Gx Interface Support Rel.

7 Gx Interface

Rel. 7 Gx Interface
Important:
The Rel. 7 Gx functionality is supported only on StarOS 8.1 and StarOS 9.0 and later. This section describes the following topics: Introduction Supported Networks and Platforms Licensing Supported Standards Terminology and Definitions How it Works Configuring Rel. 7 Gx Interface Saving the Configuration Gathering Statistics

Introduction
For IMS deployment in GPRS/UMTS networks the system uses Rel. 7 Gx interface for policy-based admission control support and flow-based charging. The Rel. 7 Gx interface supports enforcing policy control features like gating, bandwidth limiting, etc., and also supports flow-based charging. This is accomplished via dynamically provisioned Policy Control and Charging (PCC) rules. These PCC rules are used to identify Service Data Flows (SDF) and do charging. Other parameters associated with the rules are used to enforce policy control. The PCC architecture allows operators to perform service-based QoS policy, and flow-based charging control. In the PCC architecture, this is accomplished mainly by the Policy and Charging Enforcement Function (PCEF)/Cisco Systems GGSN and the Policy and Charging Rules Function (PCRF). In GPRS/UMTS networks, the client functionality lies with the GGSN, therefore in the IMS authorization scenario it is also called the Gateway. In the following figure, Gateway is the Cisco Systems GGSN, and the PCEF function is provided by Enhanced Charging Service (ECS). The Rel 7. Gx interface is implemented as a Diameter connection. The Gx messages mostly involve installing/modifying/removing dynamic rules and activating/deactivating predefined rules. The Rel. 7 Gx reference point is located between the Gateway and the PCRF. This reference point is used for provisioning and removal of PCC rules from the PCRF to the Gateway, and the transmission of traffic plane events from the Gateway to the PCRF. The Gx reference point can be used for charging control, policy control, or both by applying AVPs relevant to the application. The following figure shows the reference points between various elements involved in the policy and charging architecture.

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Figure 8.

PCC Logical Architecture

Subscription Profile Repository (SPR)

Application Function (AF)

Rx
Policy and Charging Rules Function (PCRF)

Online Charging System (OCS) Sp

CAMEL SCP Service Data Flow Based Credit Control

Gx
Policy and Charging Enforcement Function (PCEF)

Gy

Gateway Ga
Offline Charging System (OFCS)

Within the Gateway, the IMSA and DPCA modules handle the Gx protocol related functions (at the SessMgr) and the policy enforcement and charging happens at ECS. The Gy protocol related functions are handled within the DCCA module (at the ECS). The following figure shows the interaction between components within the Gateway.

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Figure 9.

PCC Architecture within Cisco PCEF

Starent GGSN/PCEF

DPCA

IMSA

ACS

DCCA
ECSv2

Rel. 7 Gx PCRF

Gy OCS

Supported Networks and Platforms

This feature is supported on all ASR 5000 Series Platforms with StarOS Release 8.1 and later running GGSN service for the core network services.

Licensing
This feature requires the following licenses to be installed on the chassis: [ 600-00-7585 ] Dynamic Policy Interface for IMS Authorization Service feature [ 600-00-7574 ] Enhanced Charging Bundle 2 1k Sessions for ECS functionality

Supported Standards
The Rel 7. Gx interface support is based on the following standards and RFCs: 3GPP TS 23.203 V7.6.0 (2008-03): 3rd Generation Partnership Project; Technical Specification Group Services and System Aspects; Policy and charging control architecture (Release 7) 3GPP TS 29.212 V7.8.0 (2009-03): 3rd Generation Partnership Project; Technical Specification Group Core Network and Terminals; Policy and Charging Control over Gx reference point (Release 7)

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

3GPP TS 29.213 V7.4.0 (2008-03): 3rd Generation Partnership Project; Technical Specification Group Core Network and Terminals; Policy and Charging Control signalling flows and QoS parameter mapping; (Release 7) RFC 3588, Diameter Base Protocol; September 2003 RFC 4006, Diameter Credit-Control Application; August 2005

Terminology and Definitions

Policy Control
The process whereby the PCRF indicates to the PCEF how to control the IP-CAN bearer. Policy control comprises the following functions: Binding: Binding is the generation of an association between a Service Data Flow (SDF) and the IP CAN bearer (for GPRS a PDP context) transporting that SDF. The QoS demand in the PCC rule, as well as the SDF template are input for the bearer binding. The selected bearer will have the same QoS Class as the one indicated by the PCC rule. Depending on the type of IP-CAN and bearer control mode, bearer binding can be executed either by the PCRF, or both PCRF and PCEF. For UE-only IP-CAN bearer establishment mode, the PCRF performs bearer binding. When the PCRF performs bearer binding, it indicates the bearer (PDP context) by means of Bearer ID. The Bearer ID uniquely identifies the bearer within the PDP session. For UE/NW IP-CAN bearer establishment mode, the PCRF performs the binding of the PCC rules for user controlled services, while the PCEF performs the binding of the PCC rules for the networkcontrolled services. Gating Control: Gating control is the blocking or allowing of packets, belonging to an SDF, to pass through to the desired endpoint. A gate is described within a PCC rule and gating control is applied on a per SDF basis. The commands to open or close the gate leads to the enabling or disabling of the passage for corresponding IP packets. If the gate is closed, all packets of the related IP flows are dropped. If the gate is opened, the packets of the related IP flows are allowed to be forwarded. Event Reporting: Event reporting is the notification of and reaction to application events to trigger new behavior in the user plane as well as the reporting of events related to the resources in the Gateway (PCEF). Event triggers may be used to determine which IP-CAN session modification or specific event causes the PCEF to re-request PCC rules. Although event trigger reporting from PCEF to PCRF can apply for an IP CAN session or bearer depending on the particular event, provisioning of event triggers will be done at session level. Note that in 11.0 and later releases, RAR with unknown event triggers are silently ignored and responded with DIAMETER_SUCCESS. In earlier releases, when unknown event triggers were received in the RAR command from PCRF, invalid AVP result code was set in the RAA command. The Event Reporting Function (ERF) receives event triggers from PCRF during the Provision of PCC Rules procedure and performs event trigger detection. When an event matching the received event
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

trigger occurs, the ERF reports the occurred event to the PCRF. If the provided event triggers are associated with certain parameter values then the ERF includes those values in the response back to the PCRF. The Event Reporting Function is located in the PCEF.

Important: In this release, event triggers IP-CAN_CHANGE and MAX_NR_BEARERS_REACHED are not supported.
QoS Control: QoS control is the authorization and enforcement of the maximum QoS that is authorized for a SDF or an IP-CAN bearer or a QoS Class Identifier (QCI). In case of an aggregation of multiple SDFs (for GPRS a PDP context), the combination of the authorized QoS information of the individual SDFs is provided as the authorized QoS for this aggregate. QoS control per SDF allows the PCC architecture to provide the PCEF with the authorized QoS to be enforced for each specific SDF. The enforcement of the authorized QoS of the IP-CAN bearer may lead to a downgrading or upgrading of the requested bearer QoS by the Gateway (PCEF) as part of a UE-initiated IP-CAN bearer establishment or modification. Alternatively, the enforcement of the authorized QoS may, depending on operator policy and network capabilities, lead to network-initiated IP-CAN bearer establishment or modification. If the PCRF provides authorized QoS for both, the IP-CAN bearer and PCC rule(s), the enforcement of authorized QoS of the individual PCC rules takes place first. QoS authorization information may be dynamically provisioned by the PCRF, or it can be a predefined PCC rule in the PCEF. In case the PCRF provides PCC rules dynamically, authorized QoS information for the IP-CAN bearer (combined QoS) may be provided. For a predefined PCC rule within the PCEF, the authorized QoS information takes affect when the PCC rule is activated. The PCEF combines the different sets of authorized QoS information, i.e. the information received from the PCRF and the information corresponding to the predefined PCC rules. The PCRF knows the authorized QoS information of the predefined PCC rules and takes this information into account when activating them. This ensures that the combined authorized QoS of a set of PCC rules that are activated by the PCRF is within the limitations given by the subscription and operator policies regardless of whether these PCC rules are dynamically provided, predefined, or both.

Important:
Supported Features:

In this release, QoS Resource Reservation is not supported.

Provisioning and Policy Enforcement of Authorized QoS: The PCRF may provide authorized QoS to the PCEF. The authorized QoS provides appropriate values for resources to be enforced. Provisioning of Authorized QoS Per IP CAN Bearer: The authorized QoS per IP-CAN bearer is used if the bearer binding is performed by the PCRF. Policy Enforcement for Authorized QoS per IP CAN Bearer: The PCEF is responsible for enforcing the policy-based authorization, i.e. to ensure that the requested QoS is in-line with the Authorized QoS per IP CAN Bearer. Policy Provisioning for Authorized QoS Per SDF: The provisioning of authorized QoS per SDF is a part of PCC rule provisioning procedure. Policy Enforcement for Authorized QoS Per SDF: If an authorized QoS is defined for a PCC rule, the PCEF limits the data rate of the SDF corresponding to that PCC rule not to exceed the maximum authorized bandwidth for the PCC rule by discarding packets exceeding the limit.
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Upon deactivation or removal of a PCC rule, the PCEF frees the resources reserved for that PCC rule. If the PCRF provides authorized QoS for both the IP-CAN bearer and PCC rule(s), the enforcement of authorized QoS of the individual PCC rules takes place first.

Important:
supported.

In this release, coordination of authorized QoS scopes in mixed mode (BCM = UE_NW) is not

Provisioning of Authorized QoS Per QCI: If the PCEF performs the bearer binding, the PCRF may provision an authorized QoS per QCI for non-GBR bearer QCI values. If the PCRF performs the bearer binding the PCRF does not provision an authorized QoS per QCI. The PCRF does not provision an authorized QoS per QCI for GBR bearer QCI values. Policy Enforcement for Authorized QoS per QCI: The PCEF can receive an authorized QoS per QCI for non GBR-bearer QCI values. Other Features: Bearer Control Mode Selection: The PCEF may indicate, via the Gx reference point, a request for Bearer Control Mode (BCM) selection at IP-CAN session establishment or IP-CAN session modification (as a consequence of an SGSN change). It will be done using the PCC Rule Request procedure. If the Bearer-Control-Mode AVP is not received from PCRF, the IP-CAN session is not terminated. The value negotiated between UE/SGSN/GGSN is considered as the BCM. The following values are considered for each of the service types: GGSN: The negotiated value between UE/SGSN/GGSN is considered. In the following scenarios UE_ONLY is chosen as the BCM: Scenario 1: UE-> UE_ONLY SGSN-> UE_ONLY GGSN-> UE_ONLY PCRF-> NO BCM Scenario 2: UE-> UE_ONLY SGSN-> UE_ONLY GGSN-> Mixed PCRF-> NO BCM GTP-PGW: BCM of UE_NW is considered. IPSG: BCM of UE_ONLY is considered. HSGW/SGW/PDIF/FA/PDSN/HA/MIPV6HA: BCM of NONE is considered. PCC Rule Error Handling: If the installation/activation of one or more PCC rules fails, the PCEF includes one or more Charging-Rule-Report AVP(s) in either a CCR or an RAA command for the
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

affected PCC rules. Within each Charging-Rule-Report AVP, the PCEF identifies the failed PCC rule(s) by including the Charging-Rule-Name AVP(s) or Charging-Rule-Base-Name AVP(s), identifies the failed reason code by including a Rule-Failure-Code AVP, and includes the PCC-RuleStatus AVP. If the installation/activation of one or more new PCC rules (i.e., rules which were not previously successfully installed) fails, the PCEF sets the PCC-Rule-Status to INACTIVE for both the PUSH and the PULL modes. If a PCC rule was successfully installed/activated, but can no longer be enforced by the PCEF, the PCEF shall send the PCRF a new CCR command and include a Charging-Rule-Report AVP. The PCEF shall include the Rule-Failure-Code AVP within the Charging-Rule-Report AVP and shall set the PCC-Rule-Status to INACTIVE. Time of the Day Procedures: PCEF performs PCC rule request as instructed by the PCRF. Revalidation-Time when set by the PCRF, causes the PCEF to trigger a PCRF interaction to request PCC rules from the PCRF for an established IP CAN session. The PCEF stops the timer once the PCEF triggers a REVALIDATION_TIMEOUT event.

Important: In 11.0 and later releases Rule-Activation-Time / Rule-Deactivation-Time / Revalidation-Time AVP is successfully parsed only if its value corresponds to current time or a later time than the current IPSG time, else the AVP and entire message is rejected. In earlier releases the AVP is successfully parsed only if its value corresponds to a later time than the current IPSG time, else the AVP and entire message is rejected.

Charging Control
Charging Control is the process of associating packets belonging to a SDF to a charging key, and applying online charging and/or offline charging, as appropriate. Flow-based charging handles differentiated charging of the bearer usage based on real time analysis of the SDFs. In order to allow for charging control, the information in the PCC rule identifies the SDF and specifies the parameters for charging control. The PCC rule information may depend on subscription data. In the case of online charging, it is possible to apply an online charging action upon PCEF events (e.g. re-authorization upon QoS change). It is possible to indicate to the PCEF that interactions with the charging systems are not required for a PCC rule, i.e. to perform neither accounting nor credit control for this SDF, and then no offline charging information is generated. Supported Features: Provisioning of Charging-related Information for the IP-CAN Session Provisioning of Charging Addresses: Primary or secondary event charging function name (Online Charging Server (OCS) addresses)

Important: In this release, provisioning of primary or secondary charging collection function name (Offline Charging Server (OFCS) addresses) over Gx is not supported.
Provisioning of Default Charging Method: In this release, the default charging method is sent in CCR-I message. For this, new AVPs Online/Offline are sent in CCR-I message based on the configuration.

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Charging Correlation
For the purpose of charging correlation between SDF level and application level (e.g. IMS) as well as on-line charging support at the application level, applicable charging identifiers and IP-CAN type identifiers are passed from the PCRF to the AF, if such identifiers are available. For IMS bearer charging, the IP Multimedia Core Network (IM CN) subsystem and the Packet Switched (PS) domain entities are required to generate correlated charging data. In order to achieve this, the Gateway provides the GGSN Charging Identifier (GCID) associated with the PDP context along with its address to the PCRF. The PCRF in turn sends the IMS Charging Identifier (ICID), which is provided by the P-CSCF, to the Gateway. The Gateway generates the charging records including the GCID as well as the ICID if received from PCRF, so that the correlation of charging data can be done with the billing system. PCRF also provides the flow identifier, which uniquely identifies an IP flow in an IMS session.

Policy and Charging Control (PCC) Rules

A PCC rule enables the detection of an SDF and provides parameters for policy control and/or charging control. The purpose of the PCC rule is to: Detect a packet belonging to an SDF. Select downlink IP CAN bearers based on SDF filters in the PCC rule. Enforce uplink IP flows are transported in the correct IP CAN bearer using the SDF filters within the PCC rule. Identify the service that the SDF contributes to. Provide applicable charging parameters for an SDF. Provide policy control for an SDF. The PCEF selects a PCC rule for each packet received by evaluating received packets against SDF filters of PCC rules in the order of precedence of the PCC rules. When a packet matches a SDF filter, the packet matching process for that packet is completed, and the PCC rule for that filter is applied.

There are two types of PCC rules:

Dynamic PCC Rules: Rules dynamically provisioned by the PCRF to the PCEF via the Gx interface. These PCC rules may be either predefined or dynamically generated in the PCRF. Dynamic PCC rules can be activated, modified, and deactivated at any time. Predefined PCC Rule: Rules preconfigured in the PCEF by the operators. Predefined PCC rules can be activated or deactivated by the PCRF at any time. Predefined PCC rules within the PCEF may be grouped allowing the PCRF to dynamically activate a set of PCC rules over the Gx reference point.

Important: A third kind of rule, the static PCC rule can be preconfigured in the chassis by the operators. Static PCC rules are not explicitly known in the PCRF, and are not under control of the PCRF. Static PCC rules are bound to general purpose bearer with no Gx control.
A PCC rule consists of:
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Rule Name: The rule name is used to reference a PCC rule in the communication between the PCEF and PCRF. Service Identifier: The service identifier is used to identify the service or the service component the SDF relates to. Service Data Flow Filter(s): The service flow filter(s) is used to select the traffic for which the rule applies. Precedence: For different PCC rules with overlapping SDF filter, the precedence of the rule determines which of these rules is applicable. When a dynamic PCC rule and a predefined PCC rule have the same priority, the dynamic PCC rule takes precedence. Gate Status: The gate status indicates whether the SDF, detected by the SDF filter(s), may pass (gate is open) or will be discarded (gate is closed) in uplink and/or in downlink direction. QoS Parameters: The QoS information includes the QoS class identifier (authorized QoS class for the SDF), the Allocation and Retention Priority (ARP), and authorized bitrates for uplink and downlink. Charging Key (i.e. rating group) Other charging parameters: The charging parameters define whether online and offline charging interfaces are used, what is to be metered in offline charging, on what level the PCEF will report the usage related to the rule, etc.

Important:
supported.

In this release, configuring the Metering Method and Reporting Level for dynamic PCC rules is not

PCC rules also include Application Function (AF) record information for enabling charging correlation between the application and bearer layer if the AF has provided this information via the Rx interface. For IMS, this includes the IMS Charging Identifier (ICID) and flow identifiers.

PCC Procedures over Gx Reference Point

Request for PCC rules

The PCEF, via the Gx reference point, requests for PCC rules in the following instances: At IP-CAN session establishment. At IP-CAN session modification. PCC rules can also be requested as a consequence of a failure in the PCC rule installation/activation or enforcement without requiring an event trigger.

Provisioning of PCC rules

The PCRF indicates, via the Rel. 7 Gx reference point, the PCC rules to be applied at the PCEF. This may be using one of the following procedures:

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

PULL (provisioning solicited by the PCEF): In response to a request for PCC rules being made by the PCEF, the PCRF provisions PCC rules in the CC-Answer. PUSH (unsolicited provisioning): The PCRF may decide to provision PCC rules without obtaining a request from the PCEF. For example, in response to information provided to the PCRF via the Rx reference point, or in response to an internal trigger within the PCRF. To provision PCC rules without a request from the PCEF, the PCRF includes these PCC rules in an RA-Request message. No CCR/CCA messages are triggered by this RARequest. For each request from the PCEF or upon unsolicited provision the PCRF provisions zero or more PCC rules. The PCRF may perform an operation on a single PCC rule by one of the following means: To activate or deactivate a PCC rule that is predefined at the PCEF, the PCRF provisions a reference to this PCC rule within a Charging-Rule-Name AVP and indicates the required action by choosing either the ChargingRule-Install AVP or the Charging-Rule-Remove AVP. To install or modify a PCRF-provisioned PCC rule, the PCRF provisions a corresponding Charging-RuleDefinition AVP within a Charging-Rule-Install AVP. To remove a PCC rule which has previously been provisioned by the PCRF, the PCRF provisions the name of this rule as value of a Charging-Rule-Name AVP within a Charging-Rule-Remove AVP. If the PCRF performs the bearer binding, the PCRF may move previously installed or activated PCC rules from one IP CAN bearer to another IP CAN bearer.

Important: In 11.0 and later releases, the maximum valid length for a charging rule name is 63 bytes. When the length of the charging rule name is greater than 63 bytes, a charging rule report with RESOURCES_LIMITATION as Rule-Failure-Code is sent. This charging rule report is sent only when the length of the rule name is lesser than 128 characters. When the charging rule name length is greater than or equal to 128 characters no charging rule report will be sent. In earlier releases, the length of the charging rule name constructed by PCRF was limited to 32 bytes.

Selecting a PCC Rule for Uplink IP Packets

If PCC is enabled, the PCEF selects the applicable PCC rule for each received uplink IP packet within an IP CAN bearer by evaluating the packet against uplink SDF filters of PCRF-provided or predefined active PCC rules of this IP CAN bearer in the order of the precedence of the PCC rules.

Important: When a PCRF-provided PCC rule and a predefined PCC rule have the same precedence, the uplink SDF filters of the PCRF-provided PCC rule is applied first. Important: In 11.0 and later releases, IMSA and ECS allow the PCRF to install two (or more) dynamic rules with the same precedence value. In earlier releases, for two distinct dynamic rules having the same precedence the second rule used to be rejected.
When a packet matches an SDF filter, the packet matching process for that packet is completed, and the PCC rule for that filter is applied. Uplink IP packets which do not match any PCC rule of the corresponding IP CAN bearer are discarded.

Selecting a PCC Rule and IP CAN Bearer for Downlink IP Packets

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

If PCC is enabled, the PCEF selects a PCC rule for each received downlink IP packet within an IP CAN session by evaluating the packet against downlink SDF filters of PCRF-provided or predefined active PCC rules of all IP CAN bearers of the IP CAN session in the order of the precedence of the PCC rules.

Important: When a PCRF-provided PCC rule and a predefined PCC rule have the same precedence, the downlink SDF filters of the PCRF-provided PCC rule are applied first.
When a packet matches a SDF filter, the packet matching process for that packet is completed, and the PCC rule for that filter is applied. The Downlink IP Packet is transported within the IP CAN bearer where the selected PCC rule is mapped. Downlink IP packets that do not match any PCC rule of the IP CAN session are discarded. The following procedures are also supported: Indication of IP-CAN Bearer Termination Implications Indication of IP-CAN Session Termination: When the IP-CAN session is being terminated (e.g. for GPRS when the last PDP Context within the IP-CAN session is being terminated) the PCEF contacts the PCRF. Request of IP-CAN Bearer Termination: If the termination of the last IP CAN bearer within an IP CAN session is requested, the PCRF and PCEF apply the Request of IP-CAN Session Termination procedure. Request of IP-CAN Session Termination: If the PCRF decides to terminate an IP CAN session due to an internal trigger or trigger from the SPR, the PCRF informs the PCEF. The PCEF acknowledges to the PCRF and instantly removes/deactivates all the PCC rules that have been previously installed or activated on that IP-CAN session. The PCEF applies IP CAN specific procedures to terminate the IP CAN session. For GPRS, the GGSN send a PDP context deactivation request with the teardown indicator set to indicate that the termination of the entire IP-CAN session is requested. Furthermore, the PCEF applies the Indication of IP CAN Session Termination procedure.

Volume Reporting Over Gx

This section describes the Volume Reporting over Gx feature.

License Requirement
The Volume Reporting over Gx feature is license dependant, requiring the following license: [ 600-00-7822 ] Charging Over Gx

Supported Standards
The Volume Reporting over Gx feature is based on the following standard: 3GPP TS 29.212 V9.1.0 (2009-12): 3rd Generation Partnership Project; Technical Specification Group Core Network and Terminals; Policy and Charging Control over Gx reference point (Release 9).

Feature Overview
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

The Volume Reporting over Gx feature provides PCRF the capability to make real-time decisions based on the data usage by subscribers.

Important:

Volume Reporting over Gx is applicable only for volume quota.

Important: In 10.0 release, only total data usage reporting is supported, uplink/downlink level reporting is not supported. In 10.2 and later releases, it is supported. Important:
the beginning. The PCEF only reports the accumulated usage since the last report for usage monitoring and not from

Important: If the usage threshold is set to zero (infinite threshold), no further threshold events will be generated by PCEF, but monitoring of usage will continue and be reported at the end of the session. Important:
Usage reporting on bearer termination is not supported.

The following steps explain how Volume Reporting over Gx works: 1. PCEF after receiving the message from PCRF parses the usage monitoring related AVPs, and sends the information to IMSA. 2. IMSA updates the information to ECS. 3. Once the ECS is updated with the usage monitoring information from PCRF, the PCEF (ECS) starts tracking the data usage. 4. For session-level monitoring, the ECS maintains the amount of data usage. 5. For PCC rule monitoring, usage is monitored with the monitoring key as the unique identifier. Each node maintains the usage information per monitoring key. When the data traffic is passed, the usage is checked against the usage threshold values and reported as described in the Usage Reporting section. 6. The PCEF continues to track data usage after the threshold is reached and before a new threshold is provided by the PCRF. If a new usage threshold is not provided by the PCRF in the acknowledgement of an IP-CAN Session modification where its usage was reported, then usage monitoring does not continue in the PCEF for that IP CAN session.

Usage Monitoring
Important: In this release, the Usage-Monitoring-Information AVP is expected to be present without a new threshold to disable the usage monitoring after usage reporting when the threshold is breached. If no Usage-MonitoringInformation AVP is present in the CCA-U, the monitoring will continue with the old threshold value and the reporting happens when the threshold is breached again.
Usage Monitoring at Session Level: PCRF subscribes to the session-level volume reporting over Gx by sending the Usage-Monitoring-Information AVP with the usage threshold level set in Granted-Service-Unit AVP and
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Usage-Monitoring-Level AVP set to SESSION_LEVEL(0). After the AVPs are parsed by DPCA, IMSA updates the information to ECS. Once ECS is updated usage monitoring is started and constantly checked with the usage threshold whenever the data traffic is present. Usage Monitoring at Flow Level: PCRF subscribes to the flow-level volume reporting over Gx by sending the Usage-Monitoring-Information AVP with the usage threshold level set in Granted-Service-Unit AVP and Usage-Monitoring-Level AVP set to PCC_RULE_LEVEL(1). Monitoring Key is mandatory in case of a flowlevel monitoring since the rules are associated with the monitoring key and enabling/disabling of usage monitoring at flow level can be controlled by PCRF using it. After the AVPs are parsed by DPCA, IMSA updates the information to ECS. Once ECS is updated usage monitoring is started and constantly checked with the usage threshold whenever the data traffic is present. Usage monitoring is supported for both predefined rules and dynamic rule definitions. Usage Monitoring for Predefined Rules: If the usage monitoring needs to be enabled for the predefined rules, PCRF sends the rule and the usage monitoring information containing the monitoring key and the usage threshold. The Monitoring key should be same as the one pre-configured in PCEF for that predefined rule. There can be multiple rules associated with the same monitoring key. Hence enabling a particular monitoring key would result in the data being tracked for multiple rules having the same monitoring key. After DPCA parses the AVPs IMSA updates the information to ECS. Once ECS is updated usage monitoring is started and constantly checked with the usage threshold whenever the data traffic is present. Usage Monitoring for Dynamic Rules: If the usage monitoring needs to be enabled for dynamic ruledefs, PCRF provides the monitoring key along with a charging rule definition and the usage monitoring information containing the monitoring key and the usage threshold. This would result in the usage monitoring being done for all the rules associated with that monitoring key. After DPCA parses the AVPs, IMSA updates the information to ECS. Once ECS is updated, the usage monitoring is started and constantly checked with the usage threshold whenever the data traffic is present. Monitoring key for dynamic ruledef is dynamically assigned by PCRF which is the only difference with predefined rules in case of usage monitoring.

Usage Reporting
Usage at subscriber/flow level is reported to PCRF under the following conditions: Usage Threshold Reached: PCEF records the subscriber data usage and checks if the usage threshold provided by PCRF is reached. This is done for both session and rule level reporting. For session-level reporting, the actual usage volume is compared with the usage volume threshold. For rule-level reporting the rule that hits the data traffic is used to find out if the monitoring key is associated with it, and based on the monitoring key the data usage is checked. Once the condition is met, it reports the usage information to IMSA and continues monitoring. IMSA then triggers the CCR-U if USAGE_REPORT trigger is enabled by the PCRF. The Usage-Monitoring-Information AVP is sent in this CCR with the UsedService-Unit set to the amount of data usage by subscriber. If PCRF does not provide a new usage threshold in the usage monitoring information as a result of CCR from PCEF when the usage threshold is reached, the usage monitoring is stopped at PCEF and no usage status is reported.

Important: In this release, the Usage-Monitoring-Information AVP is expected to be present without a new threshold to disable the usage monitoring after usage reporting when the threshold is breached. If no Usage-Monitoring-Information AVP is present in the CCA-U, the monitoring will
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

continue with the old threshold value and the reporting happens when the threshold is breached again. In the non-standard Volume Reporting over Gx implementation, usage monitoring will be stopped once the threshold is breached, else the monitoring will continue. There will be no further usage reporting until the CCA is received. Usage Monitoring Disabled: If the PCRF explicitly disables the usage monitoring with Usage-MonitoringSupport AVP set to USAGE_MONITORING_DISABLED, the PCEF stops monitoring and reports the usage information (when the monitoring was enabled) to PCRF if the usage monitoring is disabled by PCRF as a result of CCR from PCEF which is not related to reporting usage, other external triggers, or a PCRF internal trigger. If the PCRF does not provide a new usage threshold as a result of CCR from PCEF when the usage threshold is reached, the usage monitoring is stopped at PCEF and no further usage status is reported.

Important: In this release, the Usage-Monitoring-Information AVP is expected to be present without a new threshold to disable the usage monitoring after usage reporting when the threshold is breached. If no Usage-Monitoring-Information AVP is present in the CCA-U, the monitoring will continue with the old threshold value and the reporting happens when the threshold is breached again.
IP CAN Session Termination: When the IP CAN session is terminated, the accumulated subscriber usage information is reported to PCRF in the CCR-T from PCEF. If PCC usage level information is enabled by PCRF, the PCC usage will also be reported. PCC Rule Removal: When the PCRF deactivates the last PCC rule associated with a usage monitoring key, the PCEF sends a CCR with the data usage for that monitoring key. If the PCEF reports the last PCC rule associated with a usage monitoring key is inactive, the PCEF reports the accumulated usage for that monitoring key within the same CCR command if the Charging-Rule-Report AVP was included in a CCR command; otherwise, if the Charging-Rule-Report AVP was included in an RAA command, the PCEF sends a new CCR command to report accumulated usage for the usage monitoring key. PCRF Requested Usage Report: In 10.2 and later releases, the accumulated usage since the last report is sent even in case of immediate reporting, the usage is reset after immediate reporting and usage monitoring continued so that the subsequent usage report will have the usage since the current report. In earlier releases the behavior was to accumulate the so far usage in the next report. Revalidation Timeout: If usage monitoring and reporting is enabled and a revalidation timeout occurs, the PCEF sends a CCR to request PCC rules and reports all accumulated usage for all enabled monitoring keys since the last report (or since usage reporting was enabled if the usage was not yet reported) with the accumulated usage at IP-CAN session level (if enabled) and at service data flow level (if enabled).

Important: The Usage Reporting on Revalidation Timeout feature is available by default in non-standard implementation of Volume Reporting over Gx. In 10.2 and later releases, this is configurable in the standard implementation. This is not supported in 10.0 release for standard based volume reporting.
Once the usage is reported, the usage counter is reset to zero. The PCEF continues to track data usage from the zero value after the threshold is reached and before a new threshold is provided by the PCRF. If a new usage threshold is not provided by the PCRF in the acknowledgement of an IP-CAN Session modification where its usage was reported, then usage monitoring does not continue in the PCEF for that IP CAN session. For information on how to configure the Volume Reporting over Gx feature, see the Configuring Volume Reporting over Gx section.

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

How R7 Gx Works
This section describes how dynamic policy and charging control for subscribers works with Rel. 7 Gx interface support in GPRS/UMTS networks. The following figure and table explain the IMSA process between a system and IMS components that is initiated by the UE. In this example, the Diameter Policy Control Application (DPCA) is the Gx interface to the PCRF. The interface between IMSA with PCRF is the Gx interface, and the interface between Session Manager (SessMgr) and Online Charging Service (OCS) is the Gy interface. Note that the IMSA service and DPCA are part of SessMgr on the system and separated in the figure for illustration purpose only.
Figure 10. Rel. 7 Gx IMS Authorization Call Flow

UE 1

SessMgr

IMSA

DPCA

PCRF

ECSv2

OCS

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Table 5. Rel. 7 Gx IMS Authorization Call flow Description

Step 1 2 3 4 5 6

Description UE (IMS subscriber) requests for primary PDP context activation/creation. SessMgr allocates an IP address to the UE. SessMgr requests IMS Authorization, if IMSA is enabled for the APN. IMSA allocates resources for the IP CAN session and the bearer, and selects the PCRF to contact based on the user's selection key (ex msisdn). IMSA requests the DPCA module to issue an auth request to the PCRF. DPCA sends a CCR initial message to the selected PCRF. This message includes the Context-Type AVP set to PRIMARY and the IP address allocated to the UE. The message may include the Bearer-Usage AVP set to GENERAL. The BearerOperation is set to Establishment. The Bearer ID is included if the PCRF does the bearer binding. PCRF may send preconfigured charging rules in CCA, if a preconfigured rule set for general purpose PDP context is provided in PCRF. The dynamic rules and the authorized QoS parameters could also be included by the PCRF. DPCA passes the charging rule definition, charging rule install, QoS information received from the PCRF, event triggers, etc. along with the Bearer ID that corresponds to the rules received from the PCRF to IMSA. IMSA stores the information. If the Bearer ID is absent, and PCRF does the bearer binding, the rule is skipped. Whereas, if the Bearer ID is absent and the PCEF does the bearer binding, the rule is passed onto the ECS to perform bearer binding. DPCA calls the callback function registered with it by IMSA. IMSA stores the bearer authorized QoS information and notifies the SessMgr. Other PCRF provided information common to the entire PDP session (event trigger, primary/secondary OCS address, etc.) is stored within the IMSA. After processing the information, IMSA notifies the SessMgr about the policy authorization complete. If the validation of the rules fails in IMSA/DPCA, a failure is notified to PCRF containing the Charging-Rule-Report AVP. Else, IMSA initiates creation of ECS session. The APN name, primary/secondary OCS server address, etc. are sent to the ECS from the SessMgr. ECS performs credit authorization by sending CCR(I) to OCS with CC-Request-Type set to INITIAL_REQUEST to open the credit control session. This request includes the active Rulebase-Id (default rulebase ID from the APN/AAA) and GPRS specific attributes (e.g. APN, UMTS QoS, etc.). OCS returns a CCA initial message that may activate a statically configured Rulebase and may include pre-emptive quotas. ECS responds to SessMgr with the response message. SessMgr requests IMSA for the dynamic rules. IMSA sends the dynamic rules to SessMgr. Note that until the primary PDP context is established, all RAR messages from the PCRF are rejected. SessMgr sends the dynamic rule information to the ECS. The gate flow status information and the QoS per flow (charging rule) information are also sent in the message. ECS activates the predefined rules received, and installs the dynamic rules received. Also, the gate flow status and the QoS parameters are updated by ECS as per the dynamic charging rules. The Gx rulebase is treated as an ECS group-of-ruledefs. The response message contains the Charging Rule Report conveying the status of the rule provisioning at the ECS. ECS performs PCEF bearer binding for rules without bearer ID. If the provisioning of rules fails partially, the context setup is accepted, and a new CCR-U is sent to the PCRF with the Charging-Rule-Report containing the PCC rule status for the failed rules. If the provisioning of rules fails completely, the context setup is rejected.
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

7 8

9 10

11

12

13 14 15 16 17 18

19

Gx Interface Support Rel. 7 Gx Interface

Step 20

Description Depending on the response for the PDP Context Authorization, SessMgr sends the response to the UE and activates/rejects the call. If the Charging-Rule-Report contains partial failure for any of the rules, the PCRF is notified, and the call is activated. If the Charging-Rule-Report contains complete failure, the call is rejected. Based on the PCEF bearer binding for the PCC rules at Step 18, the outcome could be one or more network initiated PDP context procedures with the UE (Network Requested Update PDP Context (NRUPC) / Network Requested Secondary PDP Context Activation (NRSPCA)).

21

Configuring Rel. 7 Gx Interface

To configure Rel. 7 Gx interface functionality, the IMS Authorization service must be configured at the context level, and then the APN configured to use the IMS Authorization service. To configure Rel. 7 Gx interface functionality: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Configure IMS Authorization service at the context level for IMS subscriber in GPRS/UMTS network as described in the Configuring IMS Authorization Service at Context Level section. Verify your configuration as described in the Verifying the Configuration section. Configure an APN within the same context to use the IMS Authorization service for IMS subscriber as described in the Applying IMS Authorization Service to an APN section. Verify your configuration as described in the Verifying Subscriber Configuration section. Optional: Configure the Volume Reporting over Gx feature as described in the Configuring Volume Reporting over Gx section. Save your configuration as described in the Verifying and Saving Your Configuration chapter.

Important: Commands used in the configuration examples in this section provide base functionality to the extent that the most common or likely commands and/or keyword options are presented. In many cases, other optional commands and/or keyword options are available. Refer to the Command Line Interface Reference for complete information regarding all commands.

Configuring IMS Authorization Service at Context Level

Use the following example to configure IMS Authorization service at context level for IMS subscribers in GPRS/UMTS networks:

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Notes: must be the name of the context where you want to enable IMS Authorization service. must be the name of the IMS Authorization service to be configured for Rel. 7 Gx interface authentication. A maximum of 16 authorization services can be configured globally in a system. There is also a system limit for the maximum number of total configured services. To enable Rel. 7 Gx interface support, pertinent Diameter dictionary must be configured. For information on the specific Diameter dictionary to use, please contact your local service representative. When configuring the MSISDN prefix range based PCRF selection mechanism: To enable the Gx interface to connect to a specific PCRF for a range of subscribers configure and the starting and ending MSISDNs respectively. To enable the Gx interface to connect to a specific PCRF for a specific subscriber, configure both and the same MSISDN.
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

with

with

Gx Interface Support Rel. 7 Gx Interface

In StarOS 8.1 and later releases, per MSISDN prefix range table a maximum of 128 rows can be added. In StarOS 8.0 and earlier releases, a maximum of 100 rows can be added. The MSISDN ranges must not overlap between rows. The Round Robin algorithm for PCRF selection is effective only over a large number of PCRF selections, and not at a granular level. Optional: To configure the Quality of Service (QoS) update timeout for a subscriber, in the IMS Authorization Service Configuration Mode, enter the following command: Optional: To configure signalling restrictions, in the IMS Authorization Service Configuration Mode, enter the following commands:

Optional: To configure action on packets that do not match any policy gates in the general purpose PDP context, in the IMS Authorization Service Configuration Mode, enter the following command:

To configure the PCRF host destinations configured in the GGSN/PCEF, use the CLI commands. To configure the GGSN/PCEF to use a pre-defined rule when the Gx fails, set the CLI to . Policies available/in use will continue to be used and there will be no further interaction with the PCRF. For provisioning of default charging method, use the following configurations. For this, the AVPs Online and Offline will be sent in CCR-I message based on the configuration. To send Enable Online:

To send Enable Offline:

Verifying the Configuration

To verify the IMS Authorization service configuration:
Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Step 1

Change to the context where you enabled IMS Authorization service by entering the following command:

Step 2

Verify the IMS Authorization services configurations by entering the following command:

Applying IMS Authorization Service to an APN

After configuring IMS Authorization service at the context-level, an APN within the same context must be configured to use the IMS Authorization service for an IMS subscriber. Use the following example to apply IMS Authorization service functionality to a previously configured APN within the context configured in the Configuring Rel. 7 Gx Interface section.

Notes: must be the name of the context in which the IMS Authorization service was configured. must be the name of the IMS Authorization service configured for IMS authentication in the context. For Rel. 7 Gx, the ECS rulebase must be configured in the APN. ECS allows change of rulebase via Gx for PCEF binding scenarios. When the old rulebase goes away, all the rules that were installed from that rulebase are removed. This may lead to termination of a few bearers (PDP contexts) if they are left without any rules. If there is a Gx message that changes the rulebase, and also activates some predefined rules, the rulebase change is made first, and the rules are activated from the new rulebase. Also, the rulebase applies to the entire call. All PDP contexts (bearers) in one call use the same ECS rulebase. For predefined rules configured in the ECS, MBR/GBR of a dynamic/predefined rule is checked before it is used for PCEF binding. All rules (dynamic as well as predefined) have to have an MBR associated with them and all rules with GBR QCI should have GBR also configured. So for predefined rules, one needs to configure appropriate peak-data-rate, committed-data-rate as per the QCI being GBR QCI or non-GBR QCI. For more information, in the ACS Charging Action Configuration Mode, see the CLI command. Provided interpretation of the Gx rulebase is chosen to be ECS group-of-ruledefs, in the Active Charging Service Configuration Mode configure the following command:

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Verifying Subscriber Configuration

Verify the IMS Authorization service configuration for subscriber(s) by entering the following command: must be the name of the IMS Authorization service configured for IMS authentication.

Configuring Volume Reporting over Gx

This section describes the configuration required to enable Volume Reporting over Gx. To enable Volume Reporting over Gx, use the following configuration:

Notes: The maximum accepted monitoring key value by the PCEF is 4294967295. If the PCEF sends a greater value, the value is converted to an Unsigned Integer value. The CLI which enables volume usage report to be sent in event updates is available only in 10.2 and later releases. The optional keyword enables to support delta reporting wherein the usage is reported and reset at PCEF. If this option is not configured, the behavior is to send the usage information as part of event update but not reset at PCEF.

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 7 Gx Interface

Saving the Configuration

To save changes to the configuration, refer to the Verifying and Saving Your Configuration chapter.

Gathering Statistics
This section explains how to gather Rel. 7 Gx statistics and configuration information. In the following table, the first column lists what statistics to gather, and the second column lists the action to perform.
Table 6. Gathering Rel. 7 Gx Statistics and Information

Statistics/Information Information and statistics specific to policy control in IMS Authorization service. Information and statistics specific to the authorization servers used for IMS Authorization service. Information of all IMS Authorization service. Statistics of IMS Authorization service. Information, configuration, and statistics of sessions active in IMS Authorization service. Complete information, configuration, and statistics of sessions active in IMS Authorization service. Summarized information of sessions active in IMS Authorization service. Complete statistics for active charging service sessions. Information for all rule definitions configured in the service. Information for all rulebases configured in the system. Information on all group of ruledefs configured in the system. Information on policy gate counters and status.

Action to perform

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02

Gx Interface Support Rel. 8 Gx Interface

Rel. 8 Gx Interface
Important:
The Rel. 8 Gx functionality is supported only on StarOS 10.0 and StarOS 11.0 and later. This section describes the following topics: Introduction

Introduction
The Gx reference point is located between the Policy and Charging Rules Function (PCRF) and the Policy and Charging Enforcement Function (PCEF) on the Packet Data Network (PDN) Gateway (P-GW). The Gx reference point is used for provisioning and removal of PCC rules from the PCRF to the PCEF and the transmission of traffic plane events from the PCEF to the PCRF. The Gx reference point can be used for charging control, policy control, or both, by applying AVPs relevant to the application. The PCEF is the functional element that encompasses policy enforcement and flow based charging functionalities. This functional entity is located at the P-GW. The main functionalities include: Control over the user plane traffic handling at the gateway and its QoS. Service data flow detection and counting, as well as online and offline charging interactions. For a service data flow that is under policy control, the PCEF shall allow the service data flow to pass through the gateway if and only if the corresponding gate is open. For a service data flow that is under charging control, the PCEF shall allow the service data flow to pass through the gateway if and only if there is a corresponding active PCC rule and, for online charging, the OCS has authorized the applicable credit with that charging key. If requested by the PCRF, the PCEF shall report to the PCRF when the status of the related service data flow changes. In case the SDF is tunnelled at the BBERF, the PCEF shall inform the PCRF about the mobility protocol tunnelling header of the service data flows at IP-CAN session establishment.

Cisco ASR 5000 Series Enhanced Feature Configuration Guide OL-23924-02