Installation instructions

Roxtec rectangular compact systems

Tools
Components
o Spanner 13 mm (not included)
o Brush (not included)
A

C Note
o For optimum reliability, wait 24 hours or longer after installation before exposing the cables/pipes to strain or pressure.
D
o An incorrectly adapted module shall be replaced (layers shall not be reused).
o Cable/pipe with a considerable weight needs to be supported to prevent damage or subsidence to the seal.
A. Roxtec compact wedge
o Approvals or certificates may include amendments or limitations related to this application.
B. Stayplate
C. Roxtec compact module o Placing spare capacity modules close to the wedge is recommended.
D. Roxtec Lubricant o The latest version of this and related documents, such as translations, are found at roxtec.com.
o Partially installed openings shall be compressed if left unattended.

Roxtec tools Additional information

After installation inspection

o Is the wedge correctly oriented?
o Are the wedge screws tightened to full mechanical stop?
o Is the combined height of modules correct according to the frame packing height?
o Are there stayplates between every module row?
o Are all modules secured by stayplates?
o Is there visible protruding lubricant?

Scan QR code or visit roxtec.com for information about Roxtec tools. Scan QR code or visit roxtec.com for additional information, such as
drawings, apertures, videos, ratings and certificates.

Disassembly Reinstallation
1 2 3 4 1 2 3

Untighten the screws alternately Remove the wedge by lifting it Remove the modules required. Keep the module rows sorted until Clean the exposed sealing sur- Lubricate the exposed sealing Lubricate the corners thoroughly.
to full stop. Do not exceed 20 Nm. over the stayplate using a flat reinstallation. If a module needs faces. surfaces.
tool. to be replaced, all modules in
that row must be replaced.
Installation

Art No: 238752

1 2 3 4 5 A
6 7 8

Doc No: DOC-005804 rev. A

h H
A

Consider your packing plan. The combined height of the mod- Clean the aperture. Lubricate the sealing surfaces of Achieve a 0.1-1.0 mm (A) gap Adapt the modules by peeling off The number of layers may not dif- Lubricate the sealing surfaces.
Measure your frame height (H). ules equals the packing height (h). the frame with Roxtec Lubricant. between the two module halves layers. fer (A) by more than one between
This decides your packing height Lubricate the corners thoroughly. when held against the cable/pipe. the corresponding module halves.
(h).

9 10 11 12 13 14 15 16

Roxtec ® and Multidiameter ® are registered trademarks of Roxtec in Sweden and/or other countries.
Lubricate the sealing surfaces of Lubricate solid modules on the Insert a module half. Insert a cable or pipe. Cables/pipes shall go in parallel Continue to fill the transit consid- Insert a stayplate between every Ensure that the modules are se-
any spare module. Do not remove sealing surfaces. with the frame. ering your packing plan. row of modules. cured within the stayplate edges.
the core.

17 18 19 20 21 22 A B 23 24

Before inserting the final row of Separate the two stayplates and A Roxtec pre-compression tool Lubricate the indicated areas of Correctly orientate the wedge Ensure that the wedge is secured The wedge can be placed any- Tighten the screws alternately
modules, insert two stayplates. insert the final row of modules can be used to make room for the the wedge. according to the markings. within the stayplate edges. The where in the frame. in small steps until full mechani-
between the stayplates. wedge, if necessary. stop edge (A) is flush to the frame cal stop (~25-30 Nm). Protruding
(B). excess lubricant indicates a tight
seal.

25 26

Disclaimer
“The Roxtec cable and pipe entry sealing system (‘the Roxtec system’) is determine the suitability of the products for the intended process, installa-
a modular-based system of sealing products consisting of different com- tion and/or use.
ponents. Each and every one of the components is necessary for the best Roxtec gives no guarantee for the Roxtec system or any part thereof and
performance of the Roxtec system. The Roxtec system has been certified to assumes no liability for any loss or damage whatsoever, whether direct, in-
resist a number of different hazards. Any such certification, and the ability direct, consequential, loss of profit or otherwise, occurred or caused by the
of the Roxtec system to resist such hazards, is dependent on all components Roxtec systems or installations containing components not manufactured
that are installed as a part of the Roxtec system. Thus, the certification is by an authorized manufacturer and/or occurred or caused by the use of the
not valid and does not apply unless all components installed as part of the Roxtec system in a manner or for an application other than for which the
Roxtec system are manufactured by or under license from Roxtec (‘authorized Roxtec system was designed or intended.
manufacturer’). Roxtec gives no performance guarantee with respect to the Roxtec expressly excludes any implied warranties of merchantability and
The visible part of the screw will Check additional documentation, Roxtec system, unless (I) all components installed as part of the Roxtec sys- fitness for a particular purpose and all other express or implied representa-
increase during tightening. if applicable. tem are manufactured by an authorized manufacturer and (II) the purchaser tions and warranties provided by statute or common law. User determines
is in compliance with (a), and (b), below. suitability of the Roxtec system for intended use and assumes all risk and
(a) During storage, the Roxtec system or part thereof, shall be kept indoors in liability in connection therewith. In no event shall Roxtec be liable for indirect,
its original packaging at room temperature. consequential, punitive, special, exemplary or incidental damages or losses. Roxtec International AB
(b) Installation shall be carried out in accordance with Roxtec installation The Roxtec products are offered and sold in accordance with the condi- Box 540, 371 23 Karlskrona, SWEDEN
instructions in effect from time to time. tions of the Roxtec General Terms of Sales. The latest version of the Roxtec
The product information provided by Roxtec does not release the purchaser General Terms of Sales can be found and downloaded from roxtec.com/ +46 455 36 67 00, [email protected]
of the Roxtec system, or part thereof, from the obligation to independently general-terms-of-sales.” www.roxtec.com