UM2206

User manual
STM32 Nucleo-64-P boards (MB1319)

Introduction
The STM32 Nucleo-64-P boards, based on the MB1319 reference board (NUCLEO-
L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P), provide an affordable and
flexible way for users to try out new concepts and build prototypes with the STM32
microcontroller and the external SMPS (switched-mode power supply), which provides
various combinations of performance, power consumption, and features.
ARDUINO® Uno V3 connectivity and ST morpho headers provide an easy means of
expanding the functionality of the Nucleo open development platform with a wide choice of
specialized shields.
The STM32 Nucleo-64-P boards do not require any separate probe, as they integrate the
ST-LINK/V2-1 debugger/programmer. The STM32 Nucleo-64-P boards come with the
comprehensive free STM32 software libraries and examples that are available with the
STM32Cube package.

Figure 1. Nucleo-64-P board (top view) Figure 2. Nucleo-64-P board (bottom view)

Pictures are not contractual.

June 2022 UM2206 Rev 6 1/52

www.st.com 1
Contents UM2206

Contents

1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Codification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 Development environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Development toolchains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

6 Hardware layout and configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6.1 STM32 Nucleo-64-P board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.2 STM32 Nucleo-64-P board mechanical drawing . . . . . . . . . . . . . . . . . . . 15
6.2.1 Default board configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.3 Cuttable PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.4 Embedded ST-LINK/V2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.4.1 Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.4.2 ST-LINK/V2-1 firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6.4.3 Using the ST-LINK/V2-1 to program/debug the STM32 . . . . . . . . . . . . 18
6.4.4 Using the ST-LINK/V2-1 to program/debug an external STM32
application. 18
6.5 power supply and power selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.5.1 External power supply input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.5.2 External power supply output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.5.3 SMPS power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.6 Programming/debugging when the power supply is not from
ST-LINK (5V_ST_link) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.7 OSC clock sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.7.1 LSE: OSC 32 KHz clock supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.7.2 OSC clock supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

2/52 UM2206 Rev 6

UM2206 Contents

6.8 Reset sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.9 Virtual COM port: LPUART1/USART1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.10 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.11 Push-buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.12 IDD measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.13 Jumper configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.14 Configuration of the solder bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

7 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.1 USB Micro-B connector CN1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.2 ARDUINO® Uno V3 connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.3 ST morpho connectors CN5 and CN6 . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.4 External power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

8 STM32 Nucleo-64-P board information . . . . . . . . . . . . . . . . . . . . . . . . . 42

8.1 Product marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8.2 NUCLEO-L412RB-P product history . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
8.2.1 Product identification NUL412RBP$AU1 . . . . . . . . . . . . . . . . . . . . . . . . 42
8.2.2 Product identification NUL412RBP$AU2 . . . . . . . . . . . . . . . . . . . . . . . . 42
8.3 NUCLEO-L412RB-P product limitations . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8.3.1 Product identification NUL412RBP$AU1 limitations . . . . . . . . . . . . . . . 43
8.3.2 Product identification NUL412RBP$AU2 limitations . . . . . . . . . . . . . . . 43
8.4 NUCLEO-L433RC-P product history . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8.4.1 Product identification NUCLEOL433RCP/ . . . . . . . . . . . . . . . . . . . . . . . 43
8.4.2 Product identification NUL433RCP$AU1 . . . . . . . . . . . . . . . . . . . . . . . . 43
8.5 NUCLEO-L433RC-P product limitations . . . . . . . . . . . . . . . . . . . . . . . . . 43
8.5.1 Product identification NUCLEOL433RCP/ limitations . . . . . . . . . . . . . . 43
8.5.2 Product identification NUL433RCP$AU1 limitations . . . . . . . . . . . . . . . 43
8.6 NUCLEO-L452RE-P product history . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
8.6.1 Product identification NUCLEOL452REP/ . . . . . . . . . . . . . . . . . . . . . . . 43
8.6.2 Product identification NUL452REP$AU1 . . . . . . . . . . . . . . . . . . . . . . . . 44
8.7 NUCLEO-L452RE-P product limitations . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.7.1 Product identification NUCLEOL452REP/ limitations . . . . . . . . . . . . . . 44
8.7.2 Product identification NUL452REP$AU1 limitations . . . . . . . . . . . . . . . 44
8.8 Board revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

UM2206 Rev 6 3/52

4
Contents UM2206

8.8.1 MB1319 revision B-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

8.8.2 MB1319 revision C-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.8.3 MB1319 revision C-02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.9 Board known limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.9.1 Board MB1319 revision B-02 limitations . . . . . . . . . . . . . . . . . . . . . . . . 44
8.9.2 Board MB1319 revision C-01 limitations . . . . . . . . . . . . . . . . . . . . . . . . 44
8.9.3 Board MB1319 revision C-02 limitations . . . . . . . . . . . . . . . . . . . . . . . . 44

9 NUCLEO-L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P I/O

assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

10 Federal Communications Commission (FCC)

and ISED Canada Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
10.1 FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
10.1.1 Part 15.19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
10.1.2 Part 15.21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
10.1.3 Part 15.105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
10.2 ISED Canada Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
10.2.1 Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
10.2.2 Déclaration de conformité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

11 CE / RED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
11.1 EN55032 / CISPR32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

4/52 UM2206 Rev 6

UM2206 List of tables

List of tables

Table 1. Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 2. Codification explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 3. ON/OFF convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 4. Default jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 5. ST-LINK jumper configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 6. Debug connector SWD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 7. power supply capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 8. SB9 configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 9. LPUART1 connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 10. USART1 connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 11. Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 12. Solder bridge configurations and settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 13. USB Micro-B pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 14. ARDUINO® connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 15. External power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 16. NUCLEO-L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P
I/O assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 17. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

UM2206 Rev 6 5/52

5
List of figures UM2206

List of figures

Figure 1. Nucleo-64-P board (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Figure 2. Nucleo-64-P board (bottom view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 3. Hardware block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 4. STM32 Nucleo-64-P board top layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 5. STM32 Nucleo-64-P board bottom layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 6. STM32 Nucleo-64 -P board mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 7. USB composite device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 8. ST-LINK debugger: jumper configuration for on-board MCU . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 9. ST-LINK debugger: jumper configuration for external MCU . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 10. JP5[1-2]: 5V_STL power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 11. JP5[3-4]: 5V_VIN power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 12. JP5[5-6]: E5V power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 13. JP6[7-8]: 5V_USB_CHG power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 14. USB Micro-B connector CN1 (front view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 15. ARDUINO® connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 16. ARDUINO® connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 17. ST morpho connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 18. ST morpho connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 19. External power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

6/52 UM2206 Rev 6

UM2206 Features

1 Features

 STM32L4 Series Arm®(a) Cortex®-M4 core-based microcontroller in an LQFP64

package
 SMPS: significantly reduces power consumption in Run mode
 32.768 kHz LSE crystal oscillator
 One user LED shared with ARDUINO®
 Two push-buttons: USER and RESET
 ARDUINO® Uno V3 expansion connector
 ST morpho expansion connector
 External SMPS experimentation dedicated connector
 Flexible board power supply: ST-LINK/V2-1 USB VBUS or external sources
 On-board ST-LINK/V2-1 debugger/programmer with USB reenumeration capability:
mass storage, Virtual COM port, and debug port
 Comprehensive free software libraries and examples available with the STM32Cube
package
 Support of a wide choice of Integrated Development Environments (IDEs) including IAR
Embedded Workbench®, MDK-ARM, and STM32CubeIDE

a. Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.

UM2206 Rev 6 7/52

51
Ordering information UM2206

2 Ordering information

To order an STM32 Nucleo-64-P board, refer to, refer to Table 1. Additional information is
available from the datasheet and reference manual of the target STM32.

Table 1. Ordering information

Board
Order code Target STM32
reference

NUCLEO-L412RB-P STM32L412RBT6P
NUCLEO-L433RC-P MB1319 STM32L433RCT6P
NUCLEO-L452RE-P STM32L452RET6P

2.1 Codification
The meaning of the codification is explained in Table 2.

Table 2. Codification explanation

NUCLEO-XXYYRT-P Description Example: NUCLEO-L452RE-P

MCU series in STM32 32-bit Arm Cortex

XX STM32L4 Series
MCUs
YY MCU product line in the series STM32L452
R STM32 package pin count 64 pins
STM32 flash memory size:
– B for 128 Kbytes
T 512 Kbytes
– C for 256 Kbytes
– E for 512 Kbytes
-P STM32 has an external SMPS function External SMPS

8/52 UM2206 Rev 6

UM2206 Development environment

3 Development environment

3.1 System requirements

 Multi-OS support: Windows® 10, Linux® 64-bit, or macOS®(a)(b)(c)
 USB Type-A or USB Type-C® to Micro-B cable

3.2 Development toolchains

 IAR Systems® - IAR Embedded Workbench®(d)
 Keil® - MDK-ARM(d)
 STMicroelectronics - STM32CubeIDE

a. macOS® is a trademark of Apple Inc., registered in the U.S. and other countries and regions.
b. Linux® is a registered trademark of Linus Torvalds.
c. Windows is a trademark of the Microsoft group of companies.
d. On Windows® only.

UM2206 Rev 6 9/52

51
Conventions UM2206

4 Conventions

Table 3 provides the conventions used for the ON and OFF settings in the present
document.

Table 3. ON/OFF convention

Convention Definition

Jumper JPx ON Jumper fitted

Jumper JPx OFF Jumper not fitted
Jumper JPx [1-2] Jumper fitted between pin 1 and pin 2
Solder bridge SBx ON SBx connections closed by 0 Ω resistor
Solder bridge SBx OFF SBx connections left open
Resistor Rx ON Resistor soldered
Resistor Rx OFF Resistor not soldered
Capacitor Cx ON Capacitor soldered
Capacitor Cx OFF Capacitor not soldered

In this document, the references for all information that is common to all sale types, are
‘STM32 Nucleo-64-P board’ and ‘STM32 Nucleo-64-P boards’.

10/52 UM2206 Rev 6

UM2206 Quick start

5 Quick start

This section describes how to start development quickly using the STM32 Nucleo-64-P
board.
Before installing and using the product, accept the Evaluation Product License Agreement
from the www.st.com/epla webpage.

5.1 Getting started

The STM32 Nucleo-64-P board is a low-cost and easy-to-use development kit to evaluate
and start quickly a development with an STM32 microcontroller in an LQFP64 package. To
start using this board, follow the steps below:
1. Check the jumper position on the board, as shown in Table 4: Default jumper settings.
2. For correct identification of all device interfaces from the host PC, install the Nucleo
USB driver available on the www.st.com/stm32nucleo webpage, before connecting the
board.
3. To power the board, connect the Nucleo-64-P board before a PC with a USB Type-A or
USB Type-C® to Micro-B cable through USB connector CN1. As a result, the green
LED LD3 (5 V PWR) lights up, LD1 (COM) and green LED LD4 blink.
4. Press user button B1 (blue).
5. Observe that the blinking frequency of the three green LEDs LD4 changes by clicking
on the button B1.
6. The software demonstration and the several software examples that allow the user to
use the Nucleo features, are available at the www.st.com/stm32nucleo webpage.
7. Develop an application using the available examples.

UM2206 Rev 6 11/52

51
Hardware layout and configuration UM2206

6 Hardware layout and configuration

The STM32 Nucleo-64-P board is designed around the STM32 microcontrollers in a

64-pins LQFP package.
Figure 3 illustrates the connection between the STM32 and the peripherals (ST-LINK/V2-1,
push-buttons, LEDs, ARDUINO® Uno V3 connector, and ST morpho connectors).
Figure 4 and Figure 5 show the location of these features on the STM32 Nucleo-64-P
board.
The mechanical dimensions of the board are shown in Figure 6.

Figure 3. Hardware block diagram

ST-LINK/V2-1 Part JP STL
USB Micro- B
nRST
connector
Jumper

COM
SWD

Embedded
ST-LINK/V2-1
nRST

VCP
VCP

JP

SWD
UART

B1 B2
User Reset
5V
5V
LED
PWR SEL

SWD VCP
UART LED

GPIO GPIO

STM32 microcontroller
ARDUINO®
ST morpho

ST morpho
ARDUINO®

GPIO GPIO

OSC_32

VDD_MCU
VDD_1V2
32 KHz 3.3V / 1.8V
crystal

Ext PWR

12/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

6.1 STM32 Nucleo-64-P board layout

Figure 4. STM32 Nucleo-64-P board top layout

UM2206 Rev 6 13/52

51
Hardware layout and configuration UM2206

Figure 5. STM32 Nucleo-64-P board bottom layout

14/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

6.2 STM32 Nucleo-64-P board mechanical drawing

Figure 6. STM32 Nucleo-64 -P board mechanical drawing

6.2.1 Default board configuration

By default the STM32 Nucleo-64-P board is delivered with the external SMPS 1.1 V enabled
and [email protected] V. It is possible to set the board for [email protected] V. Before switching to 1.8 V, the
user must check that the extension module and the external shields connected to the
Nucleo-64-P board are 1.8 V compatible.
The default jumper configuration and [email protected] V setting are shown in Table 4.

UM2206 Rev 6 15/52

51
Hardware layout and configuration UM2206

Table 4. Default jumper settings

Jumper Definition Default position Comment

CN2 SWD interface ON [1-2] ON[3-4] On-board ST-LINK/V2-1 debugger

JP1 STLK_RST OFF -
JP4 T_NRST ON -
JP5 5 V power selection ON [1-2] 5 V from ST-LINK
JP6 IDD measurement ON STM32 VDD current measurement
ON [1-2] (default) VDD_MCU voltage selection 3.3 V
JP7 VDD_MCU
ON [2-3] (optional) VDD_MCU voltage selection 1.8 V
JP8 VDD_IN_SMPS ON VDD_1V2 SMPS input power supply

6.3 Cuttable PCB

An STM32 Nucleo-64-P board is divided into two parts: ST-LINK and target STM32. The
ST-LINK part of the PCB can be cut out to reduce the board size. In this case, the remaining
target STM32 part can only be powered by VIN, E5V, and 3.3 V on the CN5 ST morpho
connector, or by VIN and 3.3 V on the CN8 ARDUINO® connector.
It is still possible to use the ST-LINK part to program the STM32, using wires between the
CN3 and SWD available signals on the ST morpho connector (SWCLK CN5 pin 17, SWDIO
CN5 pin 15, and NRST CN5 pin 14, at the same I/O level as VDD_MCU).

6.4 Embedded ST-LINK/V2-1

The ST-LINK/V2-1 programming and debugging tool is integrated on the
STM32 Nucleo-64-P board.
For information about debugging and programming features, refer to the ST-LINK/V2 in-circuit
debugger/programmer for STM8 and STM32 user manual (UM1075) at the www.st.com
website.
The changes versus the ST-LINK/V2 version are listed below.
New features supported on ST-LINK/V2-1 are:
 USB software reenumeration
 Virtual COM port interface on USB
 Mass storage interface on USB
 USB power management request for more than 100mA current on USB
The following features are no more supported on ST-LINK/V2-1:
 SWIM interface
 Application voltage lower than 3 V (need to add level shifter to support it)

16/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

The embedded ST-LINK/V2-1 can be used in two different ways according to the jumper
configuration (refer to Table 5):
 Program/debug the STM32 on board,
 Program/debug an STM32 in an external application board using a cable connected to
the SWD connector.

Table 5. ST-LINK jumper configuration

CN Definition Default position Comment

ST-LINK/V2-1 functions enabled for

T_SWCLK / T_SWDIO ON [1-2] ON [3-4]
on-board programming (default)
CN3
ST-LINK/V2-1 functions enabled from
T_SWCLK / T_SWDIO OFF [1-2] OFF [3-4]
external connector (SWD supported)

6.4.1 Drivers
Before connecting the STM32 Nucleo-64-P board to a Windows® PC (XP, 7, 8, and 10)
through USB, install the driver for the ST-LINK/V2-1 that is available at the www.st.com
website.
In case the STM32 Nucleo-64-P board is connected to the PC before installing the driver, the
PC device manager may report some Nucleo interfaces as “Unknown”. To recover from this
situation, after installing the dedicated driver, the association of “Unknown” USB devices
found on the STM32 Nucleo-64-P board to this dedicated driver, must be updated in the
device manager manually.
Note: It is recommended to proceed by using the USB composite device, as shown in Figure 7.

Figure 7. USB composite device

6.4.2 ST-LINK/V2-1 firmware upgrade

The ST-LINK/V2-1 embeds a firmware upgrade mechanism for the in-situ upgrade through
the USB port. As the firmware may evolve during the lifetime of the ST-LINK/V2-1 product
(for example new functionalities, bug fixes, support for new microcontroller families), it is
recommended to keep the ST-LINK/V2-1 firmware up to date before starting to use an
STM32 Nucleo-64-P board. The latest version of this firmware is available at the www.st.com
website.

UM2206 Rev 6 17/52

51
Hardware layout and configuration UM2206

6.4.3 Using the ST-LINK/V2-1 to program/debug the STM32

To program the STM32, place the two jumpers marked in red on the CN2 connector, as
shown in Figure 8. Do not use the SWD connector to avoid disturbing the communication
with the STM32 microcontroller of the Nucleo-64-P board.

Figure 8. ST-LINK debugger: jumper configuration for on-board MCU

6.4.4 Using the ST-LINK/V2-1 to program/debug an external STM32

application.
It is very easy to use the ST-LINK/V2-1 to program the STM32 on an external application.
Simply remove the two jumpers from CN2, as shown in Figure 9, and connect the
application to the SWD debug connector according to Table 6.
Note: JP4 NRST (target STM32 RESET) must be OFF when CN3 pin 5 is used in an external
application.

18/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

Figure 9. ST-LINK debugger: jumper configuration for external MCU

Table 6. Debug connector SWD

Pin
Connector Pin name Signal name STM32 pin Function
number

VDD_TARGET:
1 1 PA0 VDD from application
AIN_1
2 2 T_JTCK PA5 SWD clock
3 3 GND PA12 Ground
SWD
CN3 SWD data
4 4 T_JTMS PA14
input/output
RESET of target
5 5 T_NRST PB0
STM32
6 6 T_SWO PA10 SWD out (optional)

UM2206 Rev 6 19/52

51
Hardware layout and configuration UM2206

6.5 power supply and power selection

6.5.1 External power supply input

Several DC power supplies can power the STM32 Nucleo-64-P board. It is possible to
supply the STM32 Nucleo-64-P board with any of the following sources:
 5V_ST_LINK from the ST-LINK USB connector
 VIN (7 V-12 V) from ARDUINO® connector or ST morpho connector
 E5V from ST morpho connector
 5V_USB_CHARGER from ST-LINK USB
 3.3 V on ARDUINO® connector or ST morpho connector
Note: If an external 5V DC power source is used, a power supply unit or a piece of auxiliary
equipment complying with the EN-60950-1: 2006+A11/2009 standard, which must be safety
extra-low voltage (SELV) with limited power capability, must power the Discovery kit.
The power supply capabilities are shown in Table 7.

Table 7. power supply capabilities

Input power Connector Voltage Max
Limitation
name pins range current

The maximum current depends on the

VBUS USB enumeration:
CN1 pin 1 4.75 to 5.25 V 500 mA
(5V_STLINK) – 100 mA without enumeration
– 500 mA with enumeration OK
From 7 to 12 V only and input current
capability is linked to input voltage:
– 800 mA input current when VIN=7 V
– 450 mA input current when
CN8 pin 8
VIN 7 to 12 V 800 mA 7 V<VIN<9 V
CN5 pin 24
– 300 mA input current when
10 V>VIN>9 V
– less than 300 mA input current when
VIN>10 V
E5V CN5 pin 6 4.75 to 5.25 V 500 mA
The maximum current depends on the
5V_USB_CHG CN1 pin 1 4.75 to 5.25 V 500 mA USB wall charger used to power the
Nucleo board
CN8 pin 4
Used when ST-LINK part of PCB not
3.3V CN5 pin 16 3.0 to 3.6 V -
used or removed and SB13 OFF
JP6 pin 2

5V_ST_LINK is a DC power with limitations from the ST-LINK USB connector (USB type
Micro-B connector of ST-LINK/V2-1). In this case, the JP5 jumper must be on pins 1 and 2
to select the 5V_STL power source on the JP5 silkscreen. This is the default setting. If the
USB enumeration succeeds, the 5V_ST_LINK power is enabled, by asserting the
PWR_ENn signal (from STM32F103CBT6). This pin is connected to a power switch ST890,

20/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

which powers the board. This power switch also features a current limitation to protect the
PC in case of a short circuit on board (more than 750 mA).
The STM32 Nucleo-64-P board and its shield can be powered from the ST-LINK USB
connector CN1, but only the ST-LINK circuit is powered before USB enumeration because
the host PC only provides 100 mA to the board at that time. During the USB enumeration,
the STM32 Nucleo-64-P board requires 500 mA of current to the host PC. If the host can
provide the required power, the enumeration ends by a SetConfiguration command and
then, the power transistor ST890 is switched ON, the green LED LD3 is turned ON, thus the
STM32 Nucleo-64-P board and its shield request no more than 500 mA current. If the host
is not able to provide the required current, the enumeration fails. Therefore, the power
switch ST890 stays OFF and the MCU part including the extension board is not powered. As
a consequence, the green LED LD3 stays turned OFF. In this case, it is mandatory to use an
external power supply.
USB power
5V_STL configuration: the JP5 jumper must be connected as shown in Figure 10.

Figure 10. JP5[1-2]: 5V_STL power source

VIN (5V_VIN) is the 7-12 V DC-power from the ARDUINO® CN8 pin 8 named VIN on the
ARDUINO® connector silkscreen, or from the pin 24 of the CN5 ST morpho connector. In this

UM2206 Rev 6 21/52

51
Hardware layout and configuration UM2206

case, the JP5 jumper must be on pins 3 and 4 to select the 5V_VIN power source on the JP5
silkscreen. In that case, the DC power comes from the power supply through the ARDUINO®
Uno V3 battery shield, compatible with the Adafruit® PowerBoost 500 shield.
5V_VIN configuration: The JP5 jumper must be connected as shown in Figure 11.

Figure 11. JP5[3-4]: 5V_VIN power source

E5V is the external DC power (5V DC power from ST morpho connector CN5 pin 6). In this
case, the JP5 jumper must be on pins 5 and 6 to select the E5V power source on the JP5
silkscreen.
E5V configuration: Jumper JP5[5-6] must be connected as shown in Figure 12.

22/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

Figure 12. JP5[5-6]: E5V power source

5V_USB_CHARGER is the DC power charger connected to USB ST-LINK (CN1). To select

the 5V_USB_CHARGER power source on the JP5 silkscreen, the JP5 jumper must be on
pins 7 and 8. In this case, if the STM32 Nucleo-64-P board is powered by an external USB
charger the debug is not available. If the PC is connected instead of the charger, the
limitation is no more effective. In this case, the PC could be damaged.
5V_USB_CHG configuration: the JP5 jumper must be connected as shown in Figure 13.

UM2206 Rev 6 23/52

51
Hardware layout and configuration UM2206

Figure 13. JP6[7-8]: 5V_USB_CHG power source

Caution: The solder bridge SB9 can be used to bypass the USB power protection ST890. This is not
an ST-recommended setting. SB9 can be set in case the board is powered by the USB of
the PC and the maximum current consumption on 5V_STLINK does not exceed 100 mA
(including extension board or ARDUINO® shield power consumption). In such conditions,
USB enumeration always succeeds since no more than 100 mA is requested for the PC.
Configurations of SB9 are summarized in Table 8.

Table 8. SB9 configurations

Solder
Default position Power supply Allowed current
bridge

500 mA maximum current limited by

OFF USB PWR ST890
through CN1
ON 100 mA maximum current
SB9
OFF No current limitation
VIN or E5V PWR SB9 must be removed when the board is
ON
powered(1)
1. SB9 must be removed when the board is powered by E5V (CN5 pin 6) or by VIN (CN8 pin 8 or CN5 pin 24).

24/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

Warning: In case the maximum current consumption of the STM32

Nucleo-64-P board with its extension boards exceeds
500 mA, it is recommended to power the STM32 Nucleo-64-P
board using an external power supply connected to E5V or
VIN.

6.5.2 External power supply output

5 V: 5 V (CN8 pin 5 or CN5 pin 18) can be used as the output power supply for an
ARDUINO® shield or an extension board, when the STM32 Nucleo-64-P board is powered
by USB, VIN or E5V. In this case, the maximum current allowed is shown in Table 7.
3.3 V: 3.3 V (CN8 pin 4 or CN5 pin 16) can be also used as power supply output. The
current is limited by the maximum current capability of the regulator U7 (LD39050PUR33
from STMicroelectronics). In this condition, the maximum consumption of the
STM32 Nucleo-64-P board and the connected shield must be less than 500 mA.

6.5.3 SMPS power supply

The following actions significantly improve the power figures in Run mode:
 Generate the Vcore logic supply from an external SMPS (switched-mode power supply)
or from an external connector
 Generate the VDD_MCU supply from an external SMPS (switched-mode power supply),
or from an external connector
The STM32 Nucleo-64-P board is populated with two SMPSs, U11 and U13, with the
following functions:
 SMPS U11 can supply dynamically the VDD_1V2 pins in Run mode at 1.1 V with a
maximum current of 30 mA.
 SMPS U13 can supply the VDD_MCU pin at 1.8 V with a maximum current of 50 mA
(hysteresis operation mode). The SMPS U13 can deliver higher current (PWM
operation mode) but with less efficiency. To set the U13 SMPS in PWM mode, remove
SB80 and solder SB79. This SMPS is enabled by default.
VDD_MCU configuration:
 3.3 V: JP7 [1-2] (default)
 1.8 V: JP7 [2-3] (best ULPBench score)
Note: The ST-LINK is still available in this configuration, thanks to the level shifters U5 and U6.
For all general information concerning design recommendations for the STM32 with
external SMPS, refer to the Design recommendations for STM32L4xxxx with external
SMPS, design guide for ultra-low-power applications with performance application note
(AN4978) available at the www.st.com website.

UM2206 Rev 6 25/52

51
Hardware layout and configuration UM2206

6.6 Programming/debugging when the power supply is not from

ST-LINK (5V_ST_link)
VIN or E5V is used as an external power supply in case the current consumption of the
STM32 Nucleo-64-P board and its extension boards exceed the allowed current on the
USB. In such conditions, it is still possible to use the USB for communication, programming,
or debugging only.
In this case, it is mandatory to power the board first using VIN or E5V then connect the USB
cable to the PC. Proceeding this way the enumeration succeeds, thanks to the external
power source.
The following power sequence procedure must be respected:
1. Connect jumper JP5 between pins 3 and 4 for VIN or pins 5 and 6 for E5V.
2. Be sure that SB9 is removed.
3. Connect the external power source to VIN or E5V.
4. Power ON the external power supply 7 V< VIN < 12 V to VIN, or 5 V for E5V.
5. Check that the green LED LD3 is turned ON.
6. Connect the PC to the USB connector CN1.
If this sequence is not respected, the board may be powered by VBUS first from the ST-LINK,
with the following risks:
 If the board needs more than 500 mA current, the PC may be damaged or the current
supply limited by the PC. As a consequence, the board is not powered correctly.
 500 mA is requested at the enumeration (since SB9 must be OFF): this request can be
rejected and the enumeration does not succeed if the PC cannot provide such current.
Consequently, the board is not power supplied (LED LD3 remains OFF).

6.7 OSC clock sources

Three clock sources are listed below:
 LSE, which is the 32.768 kHz crystal for the STM32 embedded RTC
 MCO, which is the 8 MHz clock from the ST-LINK MCU for the STM32 microcontroller
 HSE, which is the 8 MHz oscillator for the STM32 microcontroller. This clock is not
implemented on the STM32 Nucleo-64-P board.

6.7.1 LSE: OSC 32 KHz clock supply

There are three ways to configure the pins corresponding to the low-speed clock (LSE):
LSE on-board oscillator X3 crystal (default configuration). Refer to the Oscillator design
guide for STM8S, STM8A and STM32 microcontrollers application note (AN2867). It is
recommended to use the NX3215SA manufactured by NDK (32.768 kHz, 6 pF, 20 ppm).
Oscillator from external to PC14 input: From the external oscillator through pin 25 of the
CN5 connector.
The following configuration is needed:
 SB71 and SB72 ON
 R41 and R42 removed

26/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

LSE not used: PC14 and PC15 are used as GPIOs instead of low-speed clock providers.
The following configuration is needed:
 SB71 and SB72 ON
 R41 and R42 removed

6.7.2 OSC clock supply

There are four ways to configure the pins corresponding to the external-high-speed clock
(HSE):
MCO from ST-LINK (default: not connected): MCO output of ST-LINK MCU is used as an
input clock. This frequency cannot be changed. It is fixed at 8 MHz and connected to PH0
OSC_IN of the STM32 microcontroller.
The following configuration is needed:
 SB67, SB69, and SB70 OFF
 SB64 ON
 R19 and C10 ON respectively with 100 Ω and 20 pF
In this configuration, PH1 is used as I/O (SB68 ON).
HSE: on-board oscillator X2 crystal (default: not connected): for typical frequencies and
its capacitors and resistors, refer to the STM32 microcontroller datasheet. Refer to the
Oscillator design guide for STM8S, STM8A and STM32 microcontrollers application note
(AN2867) as the oscillator design guide for the STM32 microcontrollers. The X2 crystal has
the following characteristics: 8 MHz, 8 pF, 20 ppm. It is recommended to use NX3225GD
manufactured by NDK.
The following configuration is needed:
 SB64, SB68, SB70 OFF
 SB67 and SB69 ON
 C47 and C48 ON with 8.2 pF capacitors
External oscillator to PH0 input (default: not connected): from an external oscillator
through pin 29 of the CN5 connector.
The following configuration is needed:
 SB64, SB67, and SB69 OFF
 SB70 ON
 In this configuration, PH1 is used as I/O (SB68 ON)
HSE not used (default configuration): PH0 and PH1 are used as GPIOs and not as
clocks.
The following configuration is needed:
 SB58 and SB60 OFF
 SB59 and SB61 ON
 R21 removed

UM2206 Rev 6 27/52

51
Hardware layout and configuration UM2206

6.8 Reset sources

The reset signal of the STM32 Nucleo-64-P board is active low and the reset sources include:
 Reset button B2
 Embedded ST-LINK/V2-1
 ARDUINO® Uno V3 connector from CN8 pin 3
 ST morpho connector CN5 pin 14

6.9 Virtual COM port: LPUART1/USART1

The LPUART1 or USART1 interface of the STM32 can be connected to:
 The ST-LINK/V2-1 MCU
 The ARDUINO® Uno V3 connectors: CN9 (pins 1 and 2)
 The ST morpho connector (pins 35 and 37).
The LPUART1 or USART1 interface is selected by setting the related solder bridge (see
Table 9 and Table 10).

Table 9. LPUART1 connection

Solder bridge Feature

SB66 / SB75 ON
LPUART1 (PA2/PA3) connected to ST-LINK Virtual COM port.
SB32, SB34, SB60, SB73 OFF
SB60 / SB73 ON LPUART1 (PA2/PA3) connected to ARDUINO® and ST morpho
SB33, SB35 SB66, SB75 OFF connector.

Table 10. USART1 connection

Solder bridge Feature

SB32 / SB34 ON
USART1 (PA9/PA10) connected to ST-LINK Virtual COM port.
SB33, SB35, SB66, SB75 OFF
SB33 / SB35 ON USART1 (PA9/PA10) connected to ARDUINO® and ST morpho
SB32, SB34 SB60, SB73 OFF connector.

By default:
 Communication between the STM32 target and the ST-LINK/V2-1 MCU is enabled on
LPUART1 to support the Virtual COM port.
 Communication between the STM32 target and the ARDUINO® and ST morpho
connector is enabled on USART1.
The Virtual COM port settings are 115200 bps, 8 bits data, no parity, 1 stop bit, and no flow
control.

6.10 LEDs
Four LEDs are available on the STM32 Nucleo-64-P board. The four LEDs are located on
the top side of the board.

28/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

LD1 COM: LD1 is a bicolor LED. The LD1 default status is red. LD1 turns to green to
indicate that communication is in progress between the PC and the ST-LINK/V2-1 as
follows:
 Slow blinking red/OFF: At power-on before USB initialization
 Fast blinking red/OFF: After the first correct communication between the PC and the
ST-LINK/V2-1 (enumeration)
 Red LED ON: When initialization between the PC and the ST-LINK/V2-1 is successfully
ended
 Green LED ON: After successful STM32 communication initialization
 Blinking red/green: During communication with STM32
 Green ON: Communication well ended
 Orange ON: Communication ended with failure
LD2: 5V_USB: this red LED switch is ON when overcurrent is detected on USB VBUS. The
LED gives the information that more than 500 mA is requested on VBUS. In this case, it is
recommended to supply the board by E5V, VIN or in USB charger mode.
LD3: 5V_PWR: this green LED is ON when the STM32 Nucleo-64-P board is powered by a
5 V source.
LD4 USER: this green LED is a user LED connected to ARDUINO® signal D13
corresponding to STM32 I/O PB13. To light the LED, a high-logic state “1” has to be written in
the corresponding GPIO. A transistor is used to drive the LED when the I/O voltage is 1.8 V.
LD4 consumption does not impact the VDD STM32 power measurement, since LD4 is
isolated from it.

6.11 Push-buttons
Two buttons are available on the STM32 Nucleo-64-P board.
 B1 USER: The blue button for the user and wake-up function is connected by default to
the PC13 I/O or optionally to the PA0 I/O of the STM32. When the button is depressed
the logic state is “1”, otherwise the logic state is “0”.
 B2 RESET: The black button is connected to NRST and is used to RESET the STM32.
When the button is depressed the logic state is “0”, otherwise the logic state is “1”.
The blue and black plastic hats placed on these push-buttons can be removed if necessary
when a shield or an application board is plugged on top of the STM32 Nucleo-64-P board.
This is to avoid pressure on the buttons and consequently a possible permanent STM32
RESET.

6.12 IDD measurement

The JP6 jumper labeled IDD is used to measure the STM32 microcontroller, the level shifter,
and the SMPS consumptions (depending on solder-bridge configuration), by removing the
jumper and by connecting a multimeter:
 Jumper ON: directly powered (default)
 Jumper OFF: a multimeter or an external 3.3 V power source must be connected to
measure the consumption

UM2206 Rev 6 29/52

51
Hardware layout and configuration UM2206

Note: The STM32 Nucleo-64-P board LEDs are connected before the jumper. The LEDs
consumption does not impact the VDD_MCU power measurement.

6.13 Jumper configuration

The default jumper positions are shown in Table 4: Default jumper settings. Table 11
describes the other available jumper settings.

Table 11. Jumper settings

Jumper / CN Function State(1) Comment

ST-LINK/V2-1 enable for on-board

ON [1-2] ON [3-4]
T_SWCLK MCU debugger
CN2
T_SWDIO ST-LINK/V2-1 functions enabled for
OFF
external CN2 connector
ON [1-2] Used to reset ST-LINK MCU
JP1 STLK_RST
OFF Normal use
JP2/JP3 GND OFF GND probe
ON ST-LINK able to reset STM32
JP4 T_NRST
OFF ST-LINK not able to reset STM32
ON [1-2] 5 V from ST-LINK
ON [3-4] 5 V from VIN 7-12 V
JP5 5 V power selection ON [5-6] 5 V from E5V
ON [7-8] 5 V from USB_CHG
OFF No 5 V power, use 3.3 V
ON [1-2] VDD = 3.3 V
JP6 IDD measurement To connect the external source
OFF
(ULPBench probe as an example)
ON [1-2] VDD_MCU voltage selection = 3.3 V
JP7 VDD_MCU = 3.3 V ON [2-3] VDD_MCU voltage selection = 1.8 V
OFF No VDD_MCU (forbidden)
1.1 V external SMPS input power
ON [1-2]
supply
JP8 VDD_IN_SMPS
1.1 V external SMPS not powered.
OFF
Legacy configuration
1. The default jumper state is shown in bold.

6.14 Configuration of the solder bridges

Table 12 shows the solder bridge configurations and settings.

30/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

Table 12. Solder bridge configurations and settings

Definition Bridge State(1) Comment

SWD interface SB1/SB3

OFF Reserved, do not modify.
(reserved) /SB5/SB7
SWD interface SB2/SB4
ON Reserved, do not modify.
(default) /SB6/SB8

USB power by- ON USB power switch by-passed (not recommended)

SB9
pass mode OFF USB power switch protection enabled
ON SWO not connected through level shifter
SWO level
SB10 SWO connected through level shifter to target MCU
shifter by-pass OFF
for 1.8 V I/O configuration
SWO_MCU connected between ST-LINK and target
ON
STM32
SWO_MCU SB11
SWO_MCU not connected between ST-LINK and
OFF
target STM32
ON STLK_RX not connected through level shifter
STLK_RX by-
SB12 STLK_RX connected through level shifter to target
pass OFF
STM32 for 1.8 V I/O configuration
ON U7 LDO output provides 3.3 V
3.3 V LDO
SB13 U7 LDO output does NOT provide 3.3 V. The user
output OFF
has to connect an external 3.3 V source.
ON IOREF connected to VDD_MCU power supply
SB14
OFF IOREF NOT connected to VDD_MCU power supply
ON IOREF connected to the 3.3 V_PER power supply
IOREF
SB15 IOREF NOT connected to the 3.3 V_PER power
selection OFF
supply
ON IOREF connected to a 3.3 V power supply
SB21
OFF IOREF NOT connected to a 3.3 V power supply
ON User LED driven by PB13 (ARD_D13)
user LED SB17
OFF User LED not driven

Peripheral ON Peripheral power supply connected to 3.3 V

SB20
3.3 V OFF Peripheral power supply not powered
ON VDDUSB pin 48 powered by VDD
SB24
VDDUSB power OFF VDDUSB pin 48 is NOT powered by VDD
supply MCU
pin48 ON VDDUSB pin 48 powered by VDD_MCU
SB25
OFF VDDUSB pin 48 is NOT powered by VDD_MCU
U10 VDD_1V2 power switch powered by VDD-IN
ON
SMPS 3.3 V
SB29
VDD_1V2 switch U10 VDD_1V2 power switch NOT powered by VDD-IN
OFF
power supply SMPS 3.3 V
ON U10 VDD_1V2 power switch powered by 1.8 V
SB42
OFF U10 VDD_1V2 power switch NOT powered by 1.8 V

UM2206 Rev 6 31/52

51
Hardware layout and configuration UM2206

Table 12. Solder bridge configurations and settings (continued)

Definition Bridge State(1) Comment
ON U11/U12 powers VDD_1V2 through the U10 switch.

SB30 / SB46 U11/U12 directly powers VDD_1V2. U10 switch is not

OFF used (not recommended, see AN4978 on the
U11/U12 www.st.com website).
SMPS out
1.1 V U11/U12 directly powers VDD_1V2. U10 switch is not
ON used (not recommended, see AN4978 on the
SB43 www.st.com website).
OFF U11/U12 powers VDD_1V2 through the U10 switch.
The external Voutvcore from CN10 powers VDD_1V2
ON
through the U10 switch.
SB31 / SB46 The external Voutvcore from CN10 directly powers
OFF VDD_1V2. U10 switch is not used (not recommended,
see AN4978 on the www.st.com website).
VOUTCORE
The external Voutvcore from CN10 directly powers
ON VDD_1V2. U10 switch is not used (not recommended,
SB39 see AN4978 on the www.st.com website).
The external Voutvcore from CN10 powers VDD_1V2
OFF
through the U10 switch.
ON MCU VDD_1V2 connected to U12 VOUT2
VOUT2 SB51
OFF MCU VDD_1V2 NOT connected to U12 VOUT2
ON STLINK_RX connected to UART1_RX PA10
SB32
PA10 OFF STLINK_RX NOT connected to UART1_RX PA10
UART1_RX ON ARD_D0_RX connected to UART1_RX PA10
SB33
OFF ARD_D0_RX NOT connected to UART1_RX PA10
ON STLINK_TX connected to UART1_TX PA9
SB34
PA9 OFF STLINK_TX NOT connected to UART1_TX PA9
UART1_TX ON ARD_D1_TX connected to UART1_TX PA9
SB35
OFF ARD_D1_TX NOT connected to UART1_TX PA9
ON ARD_D1_TX connected to LPUART1_TX PA2
SB60
PA2 OFF ARD_D1_TX NOT connected to LPUART1_TX PA2
LPUART1_TX ON STLINK_TX connected to LPUART1_TX PA2
SB66
OFF STLINK_TX NOT connected to LPUART1_TX PA2
ON ARD_D0_RX connected to LPUART1_RX PA3
SB73 ARD_D0_RX NOT connected to LP UART1_RX
PA3 OFF
PA3
LPUART_RX
ON STLINK_RX connected to LPUART1_RX PA3
SB75
OFF STLINK_RX NOT connected to LPUART1_RX PA3

32/52 UM2206 Rev 6

UM2206 Hardware layout and configuration

Table 12. Solder bridge configurations and settings (continued)

Definition Bridge State(1) Comment
ON User button connected to PC13
SB50
OFF User button NOT connected to PC13
User button
ON User button connected to PA0
SB62
OFF User button NOT connected to PA0
AGND SB56 ON AGND connected to GND. Reserved, do not modify.
ON VBAT pin 1 powered by VDD_MCU
SB61
VBAT MCU OFF VBAT pin 1 NOT powered by VDD_MCU
power supply
pin1 ON VBAT pin 1 powered by VDD
SB65
OFF VBAT pin 1 NOT powered by VDD
ON ST-LINK MCO used for HSE CLK
SB64
OFF ST-LINK MCO NOT used for HSE CLK
ON HSE provided by the external HSE CLK X2
SB67/SB69
OFF HSE NOT provided by the external HSE CLK X2
HSE CLK
selection ON PH1 connected to ST morpho connector I/O usage
SB68
OFF PH1 NOT connected to ST morpho connector
ON PH0 connected to ST morpho connector
SB70 PH0 NOT connected to ST morpho connector MCO
OFF
usage
PC14 and PC15 connected to ST morpho
ON connector, LSE NOT provided by the external LSE
LSE CLK CLK X3
SB71/SB72
selection LSE provided by the external HSE CLK X3
OFF (R41/R42). PC13 and PC14 are not connected to
ST morpho connector

SMPS 1.8 V ON SMPS 1.8 V U13/U14 powered by VDD=3.3 V

SB76
part input OFF SMPS 1.8 V U13/U14 NOT powered
ON VDDA pin 13 powered by VDD
SB77
OFF VDDA pin 13 NOT powered by VDD
AVDD / VREF
ON VDDA pin 13 powered by VDD_MCU
SB78
OFF VDDA pin 13 NOT powered by VDD_MCU
SB79
U13 is in PWM mode
U13 mode SB79 ON
SYN/PWM SB80 SB80
U13 is in hysteresis mode
ON

ST1PS02 SB81/SB82
Refer to the ST1PS02 datasheet for the voltage
voltage SB90/SB91/SB94
range configuration
selection SB96/SB97

UM2206 Rev 6 33/52

51
Hardware layout and configuration UM2206

Table 12. Solder bridge configurations and settings (continued)

Definition Bridge State(1) Comment

ADP5301 output voltage factory

ADP5301 U9 ON ADP5301 opt0 = 2.5 V
SB83
VID selection ADP5301 Opt1 = 1.3 V
OFF ADP5301 output voltage defined by R39
SB84
ADP5301 EN pin driven by I/O: SMPS_EN PA4
ADP5301 U9 ON
SB84 / SB85
EN selection SB85
ADP5301 always enabled (level 1)
ON
SB86 ADP5301 set in PWM mode (500 mA out, low
ADP5301 ON efficiency)
SB86 / SB95
mode selection SB95 ADP5301 set in hysteresis mode (50 mA out, best
ON efficiency)

VDD_MCU ON VDD_MCU connected to CN11 VOUT VDD

SB87
selection OFF VDD_MCU not connected to CN11 VOUT VDD
ON Switch driven by I/O SMPS_SW PA7
SMPS_SW
SB88 Switch NOT driven by I/O,
enable OFF
Switch driven by U12 pin 1 AUX or CN11 pin 5
ST1PS02 U12 output selection by I/O SMPS_V1
ST1PS02 U12 ON
PA5
voltage SB89
selection ST1PS02 U12 output fixed by solder bridge, or
OFF
driven by U11 pin 4
SMPS U11/ U12 enabled pin driven by the I/O
SMPS ON
SMPS_EN PA4
U11/U12 SB92
enable SMPS U11/ U12 NOT enabled by I/O. Enable pin
OFF
level fixed by solder bridge or driven by CN11 pin 5
SMPS U11/ U12 power good connected to
ON
SMPS SMPS_PG PA6 I/O
U11/U12 PWR SB93 SMPS U11/ U12 power good NOT connected to
GOOD OFF I/O, but a configuration is possible for CN11 pin 7 to
drive it.
1. The default SBx state is shown in bold.

SB16, SB18, SB19, SB22, SB23, SB26, SB27, SB28, SB36, SB37, SB38, SB40, SB41,
SB44, SB45, SB47, SB48, SB49, SB52, SB53, SB54, SB55, SB57, SB58, SB59, SB63, are
linked to the STM32 configuration. Do not modify them.
All STM32 Nucleo-64-P boards are delivered with solder bridges configured according to the
target STM32 supported.

34/52 UM2206 Rev 6

UM2206 Connectors

7 Connectors

Eight connectors are implemented on the STM32 Nucleo-64-P board:

 CN1: ST-LINK USB connector
 CN7, CN8, CN9, and CN10: ARDUINO® Uno V3 connectors
 CN5 and CN6: ST morpho connectors
 CN11: External SMPS connector

7.1 USB Micro-B connector CN1

The USB connector CN1 is used to connect the embedded ST-LINK/V2-1 to the PC for
programming and debugging the STM32 Nucleo-64-P board microcontroller.

Figure 14. USB Micro-B connector CN1 (front view)

The related pinout for the USB ST-LINK connector is listed in Table 13.

Table 13. USB Micro-B pinout

Pin Pin ST-LINK
Connector Signal name Function
number name MCU pin

5V_STLINK /
1 VBUS - 5 V power
5V_USB_CHG
2 DM (D-) STLINK_USB_D_N PA11 USB diff pair M
CN1
3 DP (D+) STLINK_USB_D_P PA12 USB diff pair P
4 ID - - -
5 GND - - GND

UM2206 Rev 6 35/52

51
Connectors UM2206

7.2 ARDUINO® Uno V3 connectors

The CN7, CN8, CN9, and CN10 ARDUINO® connectors (see Figure 15) are female
connectors compatible with the ARDUINO® standard. Most shields designed for ARDUINO®
can fit the STM32 Nucleo-64-P board.
The ARDUINO® connectors on the STM32 Nucleo-64-P board support the ARDUINO® Uno V3.

Figure 15. ARDUINO® connectors

The related pinout for the ARDUINO® connector is shown in Figure 16 and listed in Table 14.

36/52 UM2206 Rev 6

UM2206 Connectors

Figure 16. ARDUINO® connector pinout

Note: ARDUINO® Uno V3 D0 and D1 signals are connected by default on USART1 (MCU I/O PA9
and PA10). For details about how to modify the UART interface, refer to Section 6.9: Virtual
COM port: LPUART1/USART1.

Table 14. ARDUINO® connector pinout

Connector Pin number Pin name Signal name STM32 pin Function

1 NC - - Reserved for test

2 IOREF - - I/O reference
3 NRST NRST NRST RESET
4 3.3 V - - 3.3 V input/output
CN8
5 5V - - 5 V output
6 GND - - GND
7 GND - - GND
8 VIN - - 7-12 V power input

UM2206 Rev 6 37/52

51
Connectors UM2206

Table 14. ARDUINO® connector pinout (continued)

Connector Pin number Pin name Signal name STM32 pin Function

1 A0 ADC PA0 ADC1_IN5

2 A1 ADC PA1 ADC1_IN6
3 A2 ADC PC3 ADC1_IN4

CN10 4 A3 ADC PC2 ADC1_IN3

ADC1_IN2/I2C3_
5 A4 ADC PC1
SDA
ADC1_IN1/I2C3_
6 A5 ADC PC0
SCL
10 SCL/D15 ARD_D15 PB8 I2C1_SCL
9 SDA/D14 ARD_D14 PB7 I2C1_SDA
8 AVDD VREF - VREF
7 GND - - Ground
6 SCK/D13 ARD_D13 PB13 SPI2_SCK

CN7 5 MISO/D12 ARD_D12 PB14 SPI2_MISO

PWM/MOSI/ TIM15_CH2/SPI2_
4 ARD_D11 PB15
D11 MOSI
TIM1_CH4/SPIx_
3 PWM/CS/D10 ARD_D10 PA11
NSS
2 PWM/D9 ARD_D9 PA8 TIM1_CH1
1 D8 ARD_D8 PB6 IO
8 D7 ARD_D7 PC7 IO
7 PWM/D6 ARD_D6 PB10 TIM2_CH3
6 PWM/D5 ARD_D5 PA15 TIM2_CH1
5 D4 ARD_D4 PB5 EXT_IT_5
4 PWM/D3 ARD_D3 PB3 TIM2_CH2
CN9
3 D2 ARD_D2 PA12 IO
PA2 / LPUSART1_TX /
2 TX/D1 ARD_D1
PA9 USART1_TX

PA3 / LPUSART1_RX /
1 RX/D0 ARD_D0
PA10 USART1_RX

38/52 UM2206 Rev 6

UM2206 Connectors

7.3 ST morpho connectors CN5 and CN6

The ST morpho connectors CN5 and CN6 are male pin headers accessible on both sides of
the STM32 Nucleo-64-P board (see Figure 17). All signals and power pins, except
VDD_CORE 1.2 V of the STM32, are available on the ST morpho connectors. An
oscilloscope, logical analyzer, or voltmeter can also probe these connectors.

Figure 17. ST morpho connector

The related pinout and the MCU assignment for the ST morpho connector are listed in
Figure 18.

UM2206 Rev 6 39/52

51
Connectors UM2206

Figure 18. ST morpho connector pinout

Note: ARDUINO® Uno V3 D0 and D1 signals are connected by default on USART1 (MCU I/O PA9
and PA10). Refer to Section 6.9: Virtual COM port: LPUART1/USART1 for details about
UART interface modification.

7.4 External power connector

The external power connector CN11 is an 8-pin, single-row, 2.54 mm-pitch connector. By
default, this connector is not soldered. The PCB footprint gives the possibility to control
easily the Vcore logic and the VDD_MCU power supply with an external source. The external
power connector is shown in Figure 19.

40/52 UM2206 Rev 6

UM2206 Connectors

Figure 19. External power connector

The related pinout for the external power connector is listed in Table 15.

Table 15. External power connector pinout

Pin
Connector Signal name STM32 pin Function
number

1 VDD VDD VDD @ 3.3 V supply

2 VOUTCORE VDD_1V2 MCU core PWR 1.2 V/1.1 V
3 VOUTVDD VDD_MCU VDD_MCU: 1.8 V / 3.3 V
4 SMPS_V1 PA5 I/O for voltage selection
CN11
5 SMPS_EN PA4 I/O for SMPS enable
6 SMPS_SW PA7 I/O for switch control
7 SMPS_PG PA6 I/O for power good signal
8 GND GND Ground

UM2206 Rev 6 41/52

51
STM32 Nucleo-64-P board information UM2206

8 STM32 Nucleo-64-P board information

8.1 Product marking

The stickers located on the top or bottom side of the PCB provide product information:
 Product order code and product identification for the first sticker
 Board reference with revision, and serial number for the second sticker
On the first sticker, the first line provides the product order code, and the second line the
product identification.
On the second sticker, the first line has the following format: "MBxxxx-Variant-yzz", where
"MBxxxx" is the board reference, "Variant" (optional) identifies the mounting variant when
several exist, "y" is the PCB revision and "zz" is the assembly revision, for example B01.
The second line shows the board serial number used for traceability.
Evaluation tools marked as "ES" or "E" are not yet qualified and therefore not ready to be
used as reference design or in production. Any consequences deriving from such usage will
not be at ST charge. In no event, ST will be liable for any customer usage of these
engineering sample tools as reference designs or in production.
"E" or "ES" marking examples of location:
 On the targeted STM32 that is soldered on the board (For an illustration of STM32
marking, refer to the STM32 datasheet "Package information" paragraph at the
www.st.com website).
 Next to the evaluation tool ordering part number that is stuck or silk-screen printed on
the board.
Some boards feature a specific STM32 device version, which allows the operation of any
bundled commercial stack/library available. This STM32 device shows a "U" marking option
at the end of the standard part number and is not available for sales.
To use the same commercial stack in their applications, the developers may need to
purchase a part number specific to this stack/library. The price of those part numbers
includes the stack/library royalties.

8.2 NUCLEO-L412RB-P product history

8.2.1 Product identification NUL412RBP$AU1

This product identification is based on the MB1319-L412RB-C01 mother board.
It embeds the STM32L412RBT6P microcontroller with silicon revision code "A". The
limitations of this silicon revision are detailed in the errata sheet STM32L412xx device errata
(ES0456).

8.2.2 Product identification NUL412RBP$AU2

This product identification is based on the MB1319-L412RB-C02 mother board.
It embeds the STM32L412RBT6P microcontroller with silicon revision code "A". The
limitations of this silicon revision are detailed in the errata sheet STM32L412xx device errata
(ES0456).

42/52 UM2206 Rev 6

UM2206 STM32 Nucleo-64-P board information

8.3 NUCLEO-L412RB-P product limitations

8.3.1 Product identification NUL412RBP$AU1 limitations

No limitation identified for this product identification.

8.3.2 Product identification NUL412RBP$AU2 limitations

No limitation identified for this product identification.

8.4 NUCLEO-L433RC-P product history

8.4.1 Product identification NUCLEOL433RCP/

This product identification is based on the MB1319-L433RC-C01 mother board.
It embeds the STM32L433RCT6P microcontroller with silicon revision code "Z". The
limitations of this silicon revision are detailed in the errata sheet STM32L433xx/443xx
device errata (ES0318).

8.4.2 Product identification NUL433RCP$AU1

This product identification is based on the MB1319-L433RC-C02 mother board.
It embeds the STM32L433RCT6P microcontroller with silicon revision code "Z". The
limitations of this silicon revision are detailed in the errata sheet STM32L433xx/443xx
device errata (ES0318).

8.5 NUCLEO-L433RC-P product limitations

8.5.1 Product identification NUCLEOL433RCP/ limitations

No limitation identified for this product identification.

8.5.2 Product identification NUL433RCP$AU1 limitations

No limitation identified for this product identification.

8.6 NUCLEO-L452RE-P product history

8.6.1 Product identification NUCLEOL452REP/

This product identification is based on the MB1319-L452RE-C01 mother board.
It embeds the STM32L452RET6P microcontroller with silicon revision code "Y". The
limitations of this silicon revision are detailed in the errata sheet STM32L452xx device errata
(ES0388).

UM2206 Rev 6 43/52

51
STM32 Nucleo-64-P board information UM2206

8.6.2 Product identification NUL452REP$AU1

This product identification is based on the MB1319-L452RE-C02 mother board.
It embeds the STM32L452RET6P microcontroller with silicon revision code "Y". The
limitations of this silicon revision are detailed in the errata sheet STM32L452xx device errata
(ES0388).

8.7 NUCLEO-L452RE-P product limitations

8.7.1 Product identification NUCLEOL452REP/ limitations

No limitation identified for this product identification.

8.7.2 Product identification NUL452REP$AU1 limitations

No limitation identified for this product identification.

8.8 Board revision history

8.8.1 MB1319 revision B-02

The revision B-02 of the MB1319 is the initially released version.

8.8.2 MB1319 revision C-01

Addition of two solder bridges (SB96 and SB97) to support the optional configuration with
U12: ST1PS02D1QTR IC.

8.8.3 MB1319 revision C-02

Replacement of LEDs and capacitor references.

8.9 Board known limitations

8.9.1 Board MB1319 revision B-02 limitations

No limitation identified for this board revision.

8.9.2 Board MB1319 revision C-01 limitations

No limitation identified for this board revision.

8.9.3 Board MB1319 revision C-02 limitations

No limitation identified for this board revision.

44/52 UM2206 Rev 6

UM2206 NUCLEO-L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P I/O assignment

9 NUCLEO-L412RB-P, NUCLEO-L433RC-P, and

NUCLEO-L452RE-P I/O assignment

Table 16. NUCLEO-L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P

I/O assignment
Pin
Pin name Signal or label Main feature / optional feature (SB)
No.

1 VBAT VBAT PWR VBAT

2 PC13 PC13 User button / I/O
3 PC14-OSC32_IN OSC32_IN / PC14 LSE CLK / I/O
4 PC15-OSC32_OUT OSC32_OUT / PC15 LSE CLK / IO
5 PH0-OSC_IN OSC_IN / PH0 I/O / HSE CLK
6 PH1-OSC_OUT OSC_OUT / PH1 I/O / HSE CLK
7 NRST NRST RESET
8 PC0 PC0 ARD_A5 - ADC1_IN1 / I2C3_SCL / IO
9 PC1 PC1 ARD_A4 - ADC1_IN2 / I2C3_SDA / IO
10 PC2 PC2 ARD_A3 - ADC1_IN3 / IO
11 PC3 PC3 ARD_A2 - ADC1_IN4 / IO
12 VSSA GND PWR GND
13 VDDA/VREF+ AVDD PWR AVDD
14 PA0 PA0 ARD_A0 - ADC1_IN5 / user button
15 PA1 PA1 ARD_A1 - ADC1_IN6
16 PA2 LPUART1_TX STLINK_TX / ARD_D1_TX
17 PA3 LPUART1_RX STLINK_RX / ARD_D0_RX
18 VSS GND PWR GND
19 VDD VDD_MCU PWR VDD_MCU 1.8 V / 3.3 V
20 PA4 PA4 SMPS_EN / IO
21 PA5 PA5 SMPS_V1 / IO
22 PA6 PA6 SMPS_PG / IO
23 PA7 PA7 SMPS_SW / IO
24 PC4 PC4 I/O
25 PB0 PB0 I/O
26 PB1 PB1 I/O
27 PB2 PB2 PB2
28 PB10 PB10 ARD_D6 / TIM2_CH3
29 PB11 PB11 I/O
30 VDD1V2 VDD12 PWR ExtSMPS 1V1

UM2206 Rev 6 45/52

51
NUCLEO-L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P I/O assignment UM2206

Table 16. NUCLEO-L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P

I/O assignment (continued)
Pin
Pin name Signal or label Main feature / optional feature (SB)
No.

31 VSS GND PWR GND

32 VDD VDD_MCU PWR VDD_MCU 1.8 V / 3.3 V
33 PB12 PB12 I/O
34 PB13 PB13 ARD_D13 - SPI2_SCK / LED / IO
35 PB14 PB14 ARD_D12 - SPI2_MISO / IO
ARD_D11 - SPI2_MOSI - TIM15_CH2 /
36 PB15 PB15
I/O
37 PC6 PC6 I/O
38 PC7 PC7 ARD_D7 / IO
39 PC8 PC8 I/O
40 PC9 PC9 I/O
41 PA8 PA8 ARD_D9 -TIM1_CH1 / IO
42 PA9 UART1_TX ARD_D1_TX / STLINK_TX
43 PA10 UART1_RX ARD_D0_RX / STLINK_RX
44 PA11 PA11 ARD_D10 -TIM1_CH4 - SPIx-CS / IO
45 PA12 PA12 ARD_D2 / IO
46 PA13 PA13 TMS_SWDIO
47 VSSUSB GND PWR GND
48 VDDUSB VDD_MCU / VDD PWR VDD_MCU 1.8 V / 3.3 V
49 PA14 PA14 TCK_SWCLK
50 PA15 PA15 ARD_D5 - TIM2_CH1 / IO
51 PC10 PC10 I/O
52 PC11 PC11 I/O
53 PC12 PC12 I/O
54 PB3 PB3 ARD_D3 - TIM2_CH2 / SWO
55 PB4 PB4 I/O
56 PB5 PB5 ARD_D4 / IT5
57 PB6 PB6 ARD_D8 / IO
58 PB7 PB7 ARD_D14 - I2C1_SDA / IO
59 PH3-BOOT0 BOOT0 BOOT0
60 PB8 PB8 ARD_D15 - I2C1_SCL / IO
61 PB9 PB9 I/O
62 VDD1V2 VDD12 PWR ExtSMPS 1.1 V

46/52 UM2206 Rev 6

UM2206 NUCLEO-L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P I/O assignment

Table 16. NUCLEO-L412RB-P, NUCLEO-L433RC-P, and NUCLEO-L452RE-P

I/O assignment (continued)
Pin
Pin name Signal or label Main feature / optional feature (SB)
No.

63 VSS GND PWR GND

64 VDD VDD_MCU PWR VDD_MCU 1.8 V / 3.3 V

UM2206 Rev 6 47/52

51
Federal Communications Commission (FCC) and ISED Canada Compliance UM2206

10 Federal Communications Commission (FCC)

and ISED Canada Compliance

10.1 FCC Compliance Statement

10.1.1 Part 15.19

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.

10.1.2 Part 15.21

Any changes or modifications to this equipment not expressly approved by
STMicroelectronics may cause harmful interference and void the user's authority to operate
this equipment.

10.1.3 Part 15.105

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception which can be determined by turning the equipment off and on, the user
is encouraged to try to correct interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on circuit different from that to which the receiver
is connected.
 Consult the dealer or an experienced radio/TV technician for help.

Responsible party (in the USA)

Terry Blanchard
Americas Region Legal | Group Vice President and Regional Legal Counsel, The Americas
STMicroelectronics, Inc.
750 Canyon Drive | Suite 300 | Coppell, Texas 75019
USA
Telephone: +1 972-466-7845

10.2 ISED Canada Compliance Statement

This device complies with FCC and ISED Canada RF radiation exposure limits set forth for
general population for mobile application (uncontrolled exposure). This device must not be
collocated or operating in conjunction with any other antenna or transmitter.

48/52 UM2206 Rev 6

UM2206 Federal Communications Commission (FCC) and ISED Canada Compliance

10.2.1 Compliance Statement

Notice: This device complies with Innovation, Science and Economic Development
Canada’s licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
ISED Canada ICES-003 Compliance Label: CAN ICES-3 (B) / NMB-3 (B).

10.2.2 Déclaration de conformité

Avis: Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement
Économique Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Etiquette de conformité à la NMB-003 d'ISDE Canada : CAN ICES-3 (B) / NMB-3 (B).

UM2206 Rev 6 49/52

51
CE / RED UM2206

11 CE / RED

11.1 EN55032 / CISPR32

Warning: This device is compliant with Class B of EN55032 / CISPR32. In a residential
environment, this equipment may cause radio interference.
Avertissement: Cet équipement est conforme à la Classe B de la EN55032 / CISPR32.
Dans un environnement résidentiel, cet équipement peut créer des interférences radio.

50/52 UM2206 Rev 6

UM2206 Revision history

Revision history

Table 17. Document revision history

Date Revision Changes

8-Jun-2017 1 Initial release.

Updated Appendix C: Federal Communications
6-Sep-2017 2 Commission (FCC) and Industry Canada (IC)
Compliance and Section Appendix D: CISPR32.
Extended document scope to the NUCLEO-L412RB-P
board: updated Introduction, Table 1: Ordering
information, ST1PS02 voltage selection in Table 12:
Solder bridge configurations and settings, and Table 16:
23-Aug-2018 3 NUCLEO-L412RB-P, NUCLEO-L433RC-P, and
NUCLEO-L452RE-P I/O assignment.
Updated Section 2: Product marking.
Updated schematics from Figure 20 to Figure 26 for
board revision C-01.
Updated UART1_TX/SB35 description in Table 12:
Solder bridge configurations and settings.
Removed Electrical schematics.
Reorganized the beginning of the document:
3-Apr-2020 4
– Updated document title
– Updated Features, Ordering information, and
Development toolchains
– Added Product marking and Codification
Updated Section 6.7.2: OSC clock supply with R19 and
C10 values for the MCO from ST-LINK configuration.
15-Dec-2020 5 Added Section 8: STM32 Nucleo-64-P board
information including Section 8.1: Product marking.
Updated Section 3: Development environment.
Updated Section 8: STM32 Nucleo-64-P board
information with added Section 8.2: NUCLEO-L412RB-
P product history to Section 8.7: NUCLEO-L452RE-P
24-Jun-2022 6 product limitations.
Removed the references to Arm® Mbed™ and
Demonstration software section.

UM2206 Rev 6 51/52

51
 UM2206

IMPORTANT NOTICE – READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgment.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of purchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks. All other
product or service names are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2022 STMicroelectronics – All rights reserved

52/52 UM2206 Rev 6