Digital Design &Computer Organization(BCS302) Module -4

MODULE 4
INPUT/OUTPUT ORGANIZATION

There are a number of input/output (I/O) devices, that can be connected to a

computer. The input maybe from a keyboard, a sensor, switch, mouse etc. Similarly
output may be a speaker, monitor, printer, a digital display etc.

These variety of I/O devices exchange information in varied format, having different
word length, transfer speed is different, but are connected to the same system and
exchange information with the same computer. Computer must be capable of handling
these wide variety of devices.

ACCESSING I/O-DEVICES
A single bus-structure can be used for connecting I/O-devices to a computer. The
simple arrangement of connecting set of I/O devices to memory and processor by
means of system bus is as shown in the figure. Such an arrangement is called as Single
Bus Organization.

Fig: A Single Bus structure

1
Digital Design &Computer Organization(BCS302) Module -4
• The single bus organization consists of
o Memory
o Processor
o System bus
o I/O device
• The system bus consists of 3 types of buses:

o Address bus (Unidirectional)

o Data bus (Bidirectional)
o Control bus (Bidirectional)

• The system bus enables all the devices connected to it to involve in the data
transfer operation.
• The system bus establishes data communication between I/O device and
processor.
• Each I/O device is assigned a unique set of address.
• When processor places an address on address-lines, the intended-
device responds to thecommand.
• The processor requests either a read or write-operation.
• The requested data are transferred over the data-lines

Steps for input operation:

• The address bus of system bus holds the address of the input device.
• The control unit of CPU generates IORD Control signal.
• When this control signal is activated the processor reads the data from
the input device(DATAIN) into the CPU register.
Steps for output operation:
• The address bus of system bus holds the address of the output device.
• The control unit of CPU generates IOWR control signal.
• When this control signal is enabled CPU transfers the data from processor
register to outputdevice(DATAOUT)

2
 Digital Design &Computer Organization(BCS302) Module -4

There are 2 schemes available to connect I/O devices to CPU

1. Memory mapped I/O:
• In this technique, both memory and I/O devices use the common bus to
transfer the data to CPU .

• same address space is used for both memory and I/O interface. They have
only one set of read and write signals.
• All memory related instructions are used for data transfer between I/O and
processor.
• In case of memory mapped I/O input operation can be
implemented as,MOVE DATAIN , R0

Source destination

This instruction sends the contents of location DATAIN to register R0.

• Similarly output can be implemented as, MOVE R DATAOUT

Source Destination

• The data is written from R0 to DATAOUT location (address of output buffer.

2) I/O Mapped I/O:
➢ In this technique, a separate bus is used for I/O devices and memory to transfer
the data to CPU. Address space for memory and I/O devices are different.
➢ Hence two sets of instruction are used for data transfer.
➢ One set for memory operations and another set for I/O
operations.Whole address space is available for the program.
➢ Eg – IN AL, DX

3
Digital Design &Computer Organization(BCS302) Module -4

I/O INTERFACE

The hardware arrangement of connecting i/p device to the system bus is as shown in
the fig.

Fig: I/O interface for an input device

This hardware arrangement is called as I/O interface. The I/O interface consists of
3 functional devicesnamely:

4
Digital Design &Computer Organization(BCS302) Module -4
1) Address Decoder:
o Its function is to decode the address, in-order to recognize the input device
whose address isavailable on the unidirectional address bus.
o The recognition of input device is done first, and then the control and data
registers becomes active.
o The unidirectional address bus of system bus is connected to input of the
address decoder asshown in figure
2) Control Circuit:
o The control bus of system bus is connected to control circuit as shown in the
fig.
o The processor sends commands to the I/O system through the control bus.
o It controls the read write operations with respect to I/O device.

3) Status & Data register:

o It specifies type of operation (either read or write operation) to be performed
on I/O device. Itspecifies the position of operation.

4) Data Register:
o The data bus carries the data from the I/O devices to or from the processor.
The data bus isconnected to the data/ status register.
o The data register stores the data, read from input device or the data, to be
written into outputdevice. There are 2 types:
DATAIN - Input-buffer associated with keyboard.
DATAOUT -Output data buffer of a display/printer.

Data buffering is an essential task of an I/O interface. Data transfer rates of

processor and memory are high, when compared with the I/O devices, hence the
data are buffered at the I/O interface circuit and then forwarded to output device,
or forwarded to processor in case of input devices.

5
 Digital Design &Computer Organization(BCS302) Module -4

Input Device DATAIN Buffer Processor

Processor DATAOUT Buffer Output Device

Input & Output registers –

Various registers in keyboard and display devices -

DATAIN register: is a part of input device. It is used to store the ASCII characters read from
keyboard.
DATAOUT register: is a part of output device. It is used to store the ASCII
characters to bedisplayed on the output device.
STATUS register stores the status of working of I/O devices –
• SIN flag – This flag is set to 1, when DATAIN buffer contains the data
from keyboard. The flag is set to 0, after the data is passed from DATAIN
buffer to the processor.
• SOUT flag – This flag is set to 1, when DATAOUT buffer is empty and
the data can be added to it by processor. The flag is set to 0, when
DATAOUT buffer has the data to be displayed.
• KIRQ (Keyboard Interrupt Request) – By setting this flag to 1, keyboard
requests the processor to obtain its service and an interrupt is sent to the
processor. It is used along with the SIN flag.

6
Digital Design &Computer Organization(BCS302) Module -4
• DIRQ(Display Interrupt Request) – The output device request the
processor to obtain its service for output operation, by activating this flag
to 1.
Control registers
KEN (keyboard Enable) – Enables the keyboard for input operations.
DEN (Display Enable) – Enables the output device for input operations.
Program Controlled I/O
➢ In this technique CPU is responsible for executing data from the memory for
output and storing data in memory for executing of Programmed I/O
➢ Drawback of the Programmed I/O: was that the CPU has to monitor the units
all the times when the program is executing. Thus, the CPU stays in a
program loop until the I/O unit indicates that it is ready for data transfer.
➢ This is a time-consuming process and the CPU time is wasted a lot in keeping
an eye to the executing of program.

• It is the process of controlling the input and output operations by executing 2

sets of instruction,one set for input operation and the next set for output
operation.

• The program checks the status of I/O register and reads or displays data.
Here the I/O operationis controlled by program.
WAITK TestBit #0, STATUS (Checks SIN
flag)Branch = 0 WAITK
Move DATAIN, R0 (Read character)[
*Code to read a character from DATAIN to R0]

This code checks the SIN flag, and if it is set to 0 (ie. If no character in DATAIN
Buffer), then move back to WAITK label. This loop continues until SIN flag is set
to 1. When SIN is 1, data ismoved from DATAIN to R0 register. Thus the program,
continuously checks for input operation.

Similarly code for Output operation,

WAITD TestBit #0, STATUS (Checks SOUT flag)
Branch = 0 WAITD
Move R0, DATAOUT (Send character for
display)
The code checks the SOUT flag, and if it is set to 1 (ie. If no character in
DATAOUT Buffer), then move back to WAITK label. This loop continues until
SOUT flag is set to 0. When SOUT is 0, data is moved from R0 register to
DATAOUT (ie. Sent by processor).

7
Digital Design &Computer Organization(BCS302) Module -4

Interrupt
• It is an event which suspends the execution of one program and begins the
execution of another program.
• In program controlled I/O, a program should continuously check whether the
I/O device is free. By this continuous checking the processor execution time is
wasted. It can be avoided by I/O device sending an ‘interrupt’ to the processor,
when I/O device is free.
• The interrupt invokes a subroutine called Interrupt Service Routine (ISR),
which resolves the cause of interrupt.
• The occurrence of interrupt causes the processor to transfer the execution
control from user program to ISR.

Program1 ISR

8
 Digital Design &Computer Organization(BCS302) Module -4

The following steps takes place when the interrupt related instruction is
executed:

• It suspends the execution of current instruction i.

• Transfer the execution control to sub program from main program.
• Increments the content of PC by 4 memory location.
• It decrements SP by 4 memory locations.
• Pushes the contents of PC into the stack segment memory whose address is
stored in SP.
• It loads PC with the address of the first instruction of the sub program.

The following steps takes place when ‘return’ instruction is executed in ISR -
• It transfers the execution control from ISR to user program.
• It retrieves the content of stack memory location whose address is stored in SP
into the PC.
• After retrieving the return address from stack memory location into the PC
it increments theContent of SP by 4 memory location.
Interrupt Latency / interrupt response time is the delay between the time
taken for receiving aninterrupt request and start of the execution of the ISR.
Generally, the long interrupt latency is unacceptable.

INTERRUPT HARDWARE
• The external device (I/O device) sends interrupt request to the processor by
activating a bus lineand called as interrupt request line.
• All I/O device uses the same single interrupt-request line.
• One end of this interrupt request line is connected to input power supply by
means of a register.
• The another end of interrupt request line is connected to INTR (Interrupt
request) signal ofprocessor as shown in the fig.

9
 Digital Design &Computer Organization(BCS302) Module -4

• The I/O device is connected to interrupt request line by means of switch,

which is grounded asshown in the fig.
• When all the switches are open the voltage drop on interrupt request line is
equal to the VDD andINTR value at process is 0.
• This state is called as in-active state of the interrupt request line.
• The I/O device interrupts the processor by closing its switch.

• When switch is closed the voltage drop on the interrupt request line is found
to be zero, as theswitch is grounded, hence INTR=0 and INTR=1.
• The signal on the interrupt request line is logical OR of requests from the
several I/O devices.Therefore, INTR=INTR1 + INTR2 + + INTRn

ENABLING AND DISABLING THE INTERRUPTS

The arrival of interrupt request from external devices or from within a process,
causes the suspension ofon-going execution and start the execution of another
program.

• Interrupt arrives at any time and it alters the sequence of execution. Hence
the interrupt to beexecuted must be selected carefully.
• All computers can enable and disable interruptions as desired.
• When an interrupt is under execution, other interrupts should not be
invoked. This is performedin a system in different ways.
• The problem of infinite loop occurs due to successive interruptions of active
INTR signals.

10
Digital Design &Computer Organization(BCS302) Module -4

• There are 3 mechanisms to solve problem of infinite loop:

1) Processor should ignore the interrupts until execution of first instruction of
the ISR.
2) Processor should automatically disable interrupts before starting the
execution of the ISR.
3) Processor has a special INTR line for which the interrupt-handling circuit.
Interrupt-circuit responds only to leading edge of signal. Such line
is called edge-triggered.
• Sequence of events involved in handling an interrupt-request:
1) The device raises an interrupt-request.
2) The processor interrupts the program currently being executed.
3) Interrupts are disabled by changing the control bits in the processor status
register (PS).
4) The device is informed that its request has been recognized. And in
response, the device deactivates the interrupt-request signal.
5) The action requested by the interrupt is performed by the interrupt-service
routine.
6) Interrupts are enabled and execution of the interrupted program is
resumed.

HANDLING MULTIPLE DEVICES

While handling multiple devices, the issues concerned are:
• How can the processor recognize the device requesting an interrupt?
• How can the processor obtain the starting address of the appropriate ISR?
• Should a device be allowed to interrupt the processor while
another interrupt isbeing serviced?
• How should 2 or more simultaneous interrupt-requests be handled?

VECTORED INTERRUPT
• A device requesting an interrupt identifies itself by sending a special-code to
processor over bus.
• Then, the processor starts executing the ISR.
• The special-code indicates starting-address of ISR.
• The special-code length ranges from 4 to 8 bits.
• The location pointed to by the interrupting-device is used to store the staring
address to ISR.

11
Digital Design &Computer Organization(BCS302) Module -4

• The staring address to ISR is called the interrupt vector.

• Processor
→ loads interrupt-vector into PC &
→ executes appropriate ISR.
• When processor is ready to receive interrupt-vector code, it activates INTA line.
• Then, I/O-device responds by sending its interrupt-vector code & turning off the
INTR signal.
• The interrupt vector also includes a new value for the Processor Status Register

INTERRUPT NESTING
• A multiple-priority scheme is implemented by using separate INTR & INTA lines for
each device
• Each INTR line is assigned a different priority-level as shown in Figure.

INTR1 INTRp
Processor

Device Device Devic p

INTA INT p

Priority

• Each device has a separate interrupt-request and interrupt-acknowledge line.

• Each interrupt-request line is assigned a different priority level.
• Interrupt requests received over these lines are sent to a priority arbitration circuit
in the processor.
• If the interrupt request has a higher priority level than the priority of the processor,
then the request is accepted.
• Priority-level of processor is the priority of program that is currently being executed.
• Processor accepts interrupts only from devices that have higher-priority than its
own.

12
 Digital Design &Computer Organization(BCS302) Module -4
• At the time of execution of ISR for some device, priority of processor is raised to
that of the device.
• Thus, interrupts from devices at the same level of priority or lower are disabled.
Privileged Instruction
• Processor's priority is encoded in a few bits of PS word. (PS = Processor-Status).
• Encoded-bits can be changed by Privileged Instructions that write into PS.
• Privileged-instructions can be executed only while processor is running in
Supervisor Mode.
• Processor is in supervisor-mode only when executing operating-system routines.
Privileged Exception
• User program cannot
→ accidently or intentionally change the priority of the processor &
→ disrupt the system-operation.
• An attempt to execute a privileged-instruction while in user-mode leads to a
Privileged Exception.
SIMULTANEOUS REQUESTS
DAISY CHAIN
• The daisy chain with multiple priority levels is as shown in the figure.
• The interrupt request line INTR is common to all devices as shown in the fig.

• The interrupt acknowledge line is connected in a daisy fashion as shown in the figure.

• This signal propagates serially from one device to another device.

• The several devices raise an interrupt by activating INTR signal. In response to

the signal, processortransfers its device by activating INTA signal.

• This signal is received by device 1. The device-1 blocks the propagation of INTA
signal to device-2,when it needs processor service.

• The device-1 transfers the INTA signal to next device when it does not require the
processor service.

• In daisy chain arrangement device-1 has the highest priority.

Advantage: It requires fewer wires than the individual connection

13
 Digital Design &Computer Organization(BCS302) Module -4

ARRANGEMENT OF PRIORITY GROUPS

• In this technique, devices are organizes in a group and each group is connected
to the processor at adifferent priority level.

• With in a group devices are connected in a daisy chain fashion as shown in the
figure.

Direct Memory Access (DMA)

• It is the process of transferring the block of data at high speed in between
main memory and external device (I/O devices) without continuous
intervention of CPU is called as DMA.
• The DMA operation is performed by one control circuit and is part of the I/O
interface.
• This control circuit is called DMA controller. Hence DMA transfer operation is
performed by DMAcontroller.
• To initiate Directed data transfer between main memory and external devices
DMA controller needsparameters from the CPU.
• These 3 Parameters are:

1) Starting address of the

memory block. 2)No of words to
be transferred.
3)Type of operation (Read or Write).
After receiving these 3 parameters from CPU, DMA controller establishes
directed data transferoperation between main memory and external devices
without the involvement of CPU.

14
 Digital Design &Computer Organization(BCS302) Module -4

• Register of DMA Controller:

It consists of 3 type of register:

Starting address register:

The format of starting address register is as shown in the fig. It is used to store
the starting addressof the memory block.

.
Word-Count register:
The format of word count register is as shown in fig. It is used to store the no of
words to be transferredfrom main memory to external devices and vice versa.

Status and Controller register:

The format of status and controller register is as shown in fig.

a) DONE bit:
• The DMA controller sets this bit to 1 when it completes the direct data
transfer between mainmemory and external devices.
• This information is informed to CPU by means of DONE bit.
b) R/W (Read or Write):
• This bit is used to differentiate between memory read or memory write
operation.
• The R/W = 1 for read operation and
= 0 for write operation.
• When this bit is set to 1, DMA controller transfers the one block of data
from external deviceto main memory.
• When this bit is set to 0, DMA controller transfers the one block of data
from main memoryto external device.

15
Digital Design &Computer Organization(BCS302) Module -4
c) IE (Interrupt enable) bit:
• The DMA controller enables the interrupt enable bit after the completion of

DMA operationd)Interrupt request (IRQ):

• The DMA controller requests the CPU to transfer new block of data
from source todestination by activating this bit.

The computer with DMA controller is as shown in the fig.:

• The DMA controller connects two external devices namely disk 1 and disk 2
to system bus asshown in the above fig.
• The DMA controller also interconnects high speed network devices to system
bus as shownin the above fig.
• Let us consider direct data transfer operation by means of DMA controller
without the involvement of CPU in between main memory and disk 1 as
indicated by dotted lines (in the fig.).
• To establish direct data transfer operation between main memory and disk
1. DMA controller request the processor to obtain 3 parameters namely:
1)Starting address of the memory block.
2)No of words to be transferred.
3)Type of operation (Read or Write).

• After receiving these 3 parameters from processor, DMA controller directly

transfers block ofdata main memory and external devices (disk 1).

16
Digital Design &Computer Organization(BCS302) Module -4

• This information is informed to CPU by setting respective bits in the

status and controllerregister of DMA controller.
These are 2 types of request with respect to
system bus1). CPU request.
2). DMA request.
Highest priority will be given to DMA request.

• Actually the CPU generates memory cycles to perform read and write
operations. The DMA controller steals memory cycles from the CPU to
perform read and write operations. This approach is called as “Cycle
stealing”.

• An exclusive option will be given for DMA controller to transfer block of data from
external devices to main memory and from main memory to external devices.
This technique is called as “Burst mode of operation.”

BUS ARBITRATION
• Any device which initiates data transfer operation on bus at any instant of
time is called as Bus-Master.
• When the bus mastership is transferred from one device to another device,
the next device isready to obtain the bus mastership.
• The bus-mastership is transferred from one device to another device based
on the principle ofpriority system. There are two types of bus-arbitration
technique:

a) Centralized bus arbitration:

In this technique CPU acts as a bus-master or any control unit connected to bus
can be acts as a busmaster.

The schematic diagram of centralized bus arbitration is as shown in the fig.:

17
Digital Design &Computer Organization(BCS302) Module -4

The following steps are necessary to transfer the bus mastership from CPU to
one of the DMAcontroller:
• The DMA controller request the processor to obtain the bus mastership by
activating BR (Busrequest) signal
• In response to this signal the CPU transfers the bus mastership to
requested devices DMAcontroller1 in the form of BG (Bus grant).
• When the bus mastership is obtained from CPU the DMA controller1 blocks the
propagation of busgrant signal from one device to another device.
• The BG signal is connected to DMA controller2 from DMA controller1 in as daisy
fashion style isas shown in the figure.
• When the DMA controller1 has not sent BR request, it transfers the bus
mastership to DMAcontroller2 by unblocking bus grant signal.
• When the DMA controller1 receives the bus grant signal, it blocks the signal from
passing to DMA controller2 and enables BBSY signal. When BBSY signal is set to 1
the set of devices connected to system bus doesn’t have any rights to obtain the bus
mastership from the CPU.

b) Distributed bus arbitration:

• In this technique 2 or more devices trying to access system bus at the same
time may participatein bus arbitration process.
• The schematic diagram of distributed bus arbitration is as shown in the figure

18
 Digital Design &Computer Organization(BCS302) MODULE -4

• The external device requests the processor to obtain bus mastership by

enabling start arbitrationsignal.
• In this technique 4 bit code is assigned to each device to request the CPU in
order to obtain busmastership.
• Two or more devices request the bus by placing 4 bit code over the system bus.
• The signals on the bus interpret the 4 bit code and produces winner as a result
from the CPU.
• When the input to the one driver = 1, and input to the another driver = 0, on
the same bus line,this state is called as “Low level voltage state of bus”.
• Consider 2 devices namely A & B trying to access bus mastership at
the same time.Let assigned code for devices A & B are 5 (0101) & 6
(0110) respectively.
• The device A sends the pattern (0101) and device B sends its pattern (0110) to
master. The signals on the system bus interpret the 4 bit code for devices A & B
produces device B as a winner.
• The device B can obtain the bus mastership to initiate direct data transfer
between external devices and main memory.
The Memory System
Speed, Size and Cost
The block diagram of memory hierarchy is as shown in the figure below.

19
 Digital Design &Computer Organization(BCS302) MODULE -4

• Registers: The fastest access is to data held in registers. Hence registers are part of
the memory hierarchy. More speed, small size and cost per bit is also more.
• At the next level of hierarchy, small amount of memory can be directly
implemented on the processor chip.
• This memory is called as processor cache. It holds the copy of recently accessed
data and instructions.
There are 2 levels of caches viz level-1 and level-2.
Level-1 cache is part of the processor and level-2 cache is placed in
between level-1 cache and main memory.
• The level-2 cache is implemented using SRAM chips

• The next level in the memory hierarchy is called as main memory. It is

implemented using dynamic memory components (DRAM). The main
memory is larger but slower than cache memory. The access time for
main memory is ten times longer than the cache memory

• The level next in the memory hierarchy is called as secondary memory.

It holds huge amount of data.

• The main-memory is built with DRAM

• SRAMs are used in cache memory, where speed is essential.

• The Cache-memory is of 2 types:

1) Primary/Processor Cache (Level1 or L1 cache)
➢ It is always located on the processor-chip.
2) Secondary Cache (Level2 or L2 cache)
➢ It is placed between the primary-cache and the rest of the memory.

20
Digital Design &Computer Organization(BCS302) MODULE -4

• The memory is implemented using the dynamic components (SIMM, DIMM).

The access time for main-memory is about 10 times longer than the
access time for L1cache.
Cache Memory
It is the fast access memory located in between processor and main memory

Processor Cache Memory Main Memory

as shown inthe fig. It is designed to reduce the access time.

The cache memory holds the copy of recently accessed data and instructions.
• The processor needs less access time to read the data and instructions from
the cache memory as compared to main memory .
• Hence by incorporating cache memory, in between processor and main
memory, itis possible to enhance the performance of the system.
• The effectiveness of cache mechanism is based on the property of
“Locality of Reference”.

Locality of Reference
• Many instructions in the localized areas of program are executed repeatedly during
sometime of execution
• Remainder of the program is accessed relatively infrequently
• There are 2 types of locality reference:
1) Temporal
➢ The recently executed instructions are likely to be executed again and again.

➢ Eg –instruction in loops, nested loops and few function calls.

2) Spatial
➢ Instructions in close proximity to recently executed instruction are likely to be
executed soon. (near by instructions)
• If active segment of program is placed in cache-memory, then total execution time
can be reduced.
• Cache Block / cache line refers to the set of contiguous address locations of some
size.

• The Cache-memory stores a reasonable number of blocks at a given time.

21
 Digital Design &Computer Organization(BCS302) MODULE -4

• This number of blocks is small compared to the total number of blocks available
in main-memory.
• Correspondence b/w main-memory-block & cache-memory-block is specified by
mapping-function.
• If the cache memory is full, one of the block should be removed to create space
forthe new block, this is decided by cache control hardware.
• The collection of rule for selecting the block to be removed is called the
Replacement Algorithm.
• The cache control-circuit determines whether the requested-word currently exists in
the cache.
• If data is available, for read-operation, the data is read from cache.
• The write-operation (writing to memory) is done in 2 ways:
1) Write-throughprotocol &
2) Write-back protocol.
Write-Through Protocol
➢ Here the cache-location and the main-memory-locations are updated
simultaneously.
Write-Back Protocol
➢ This technique is to
→ update only the cache-location &
→ mark the cache-location with a flag bit called Dirty/Modified Bit.

➢ The word in memory will be updated later, when the marked-block is

removed from cache.

During Read-operation
• If the requested-word currently does not exists in the cache, then read-miss will
occur.
• To overcome the read miss, Load–through/Early restart protocol is used.
Load–Through Protocol
➢ The block of words that contains the requested-word is copied from the
memory into cache.
➢ After entire block is loaded into cache, the requested-word is forwarded
to processor.
22
Digital Design &Computer Organization(BCS302) MODULE -4
➢

During Write-operation
• If the requested-word does not exists in the cache, then write-miss will occur.
1) If Write Through Protocol is used, the information is
written directlyinto main-memory.
2) If Write Back Protocol is used,
→ then block containing the addressed word is first brought
into the cache&
→ then the desired word in the cache is over-written
with the newinformation.

Mapping functions
There are 3 techniques to map main memory blocks into cache memory –
1. Direct mapped cache
2. Associative Mapping
3. Set-Associative Mapping
DIRECT MAPPING
• The simplest way to determine cache locations in which to store memory blocks
is the direct mapping technique as shown in the figure.

• Cache block number= (block-j of main memory)%128; • If there are 128

blocks in a cache, the
block-j of the main-memory maps onto block-jmodulo-128 of the cache . When the memory-blocks
0, 128, & 256 are loaded into cache, the block is stored in cache-block 0. Similarly, memory-
blocks 1, 129, 257 are stored in cache-block 1.(eg:1mod 128=1,
129 mod 128=1)
• The contention may arise
1) Even when the cache is full.
2) But more than one memory-block is mapped onto a given cache-block position.
• The contention is resolved by allowing the new blocks to overwrite the currently resident-block.
Memory-address determines placement of block in the cache.

23
 Digital Design &Computer Organization(BCS302) MODULE -4

main memory block has to be placed in particular

cache block number by using below formula
Cache block number=main memory block number
% number of blocks present in cache memory.

For eg: main memory block 129 has to be placed in

cache block number 1 by using above formula i.e
Cache block number=129 % 128 (consider
remainder that is 1).
Cache block number=258 % 128 (consider
remainder that is 2).
Main memory block 258 has to be placed in cache
block 2

• The main memory block is loaded into cache block by means of memory address. The main memory
address consists of 3 fields as shown in the figure.
• Each block consists of 16 words. Hence least significant 4 bits are used to select one of the 16
words.

• The 7bits of memory address are used to specify the position of the cache block, location. The most
significant 5 bits of the memory address are stored in the tag bits. The tag bits are used to map one of
25 = 32 blocks into cache block location (tag bit has value 0-31).
• The higher order 5 bits of memory address are compared with the tag bits associated with cache
location. If they match, then the desired word is in that block of the cache.
• If there is no match, then the block containing the required word must first be read from the main memory

24
Digital Design &Computer Organization(BCS302) MODULE -4
and loaded into the cache. It is very easy to implement, but not flexible.

2. Associative Mapping:
• It is also called as associative mapped cache. It is much more flexible.
• In this technique main memory block can be placed into any cache block
position.
• In this case , 12 tag bits are required to identify a memory block when it is
resident of the cache memory.
• The Associative Mapping technique is illustrated as shown in the fig.

• In this technique 12 bits of address generated by the processor are compared with
the tag bits of each block of the cache to see if the desired block is present. This
is called as associative mapping technique.

25
Digital Design &Computer Organization(BCS302) MODULE -4

3. Set Associative Mapping:

• It is the combination of direct and associative mapping techniques.
• The blocks of cache are divided into several groups. Such a groups are called as
sets.
• Each set consists of number of cache blocks. A memory block is loaded into one
of the cache sets.
• The main memory address consists of three fields, as shown in the figure.
• The lower 4 bits of memory address are used to select a word from a 16
words.
• A cache consists of 64 sets as shown in the figure. Hence 6 bit set field is used
to select a cache set from 64 sets.
• As there are 64 sets, the memory is divided into groups containing 64 blocks,
where each group is given a tag number.
• The most significant 6 bits of memory address is compared with the tag
fields of each set to determine whether memory block is available or not.
• The following figure clearly describes the working principle of Set
Associative Mapping technique.
• cache that has “k” blocks per set is called as “k-way set associative cache‟.
• Each block contains a control-bit called a valid-bit.
• The Valid-bit indicates that whether the block contains valid-data (updated data).
• The dirty bit indicates that whether the block has been modified during its cache
residency.
Valid-bit=0 - When power is initially applied to system.

Valid-bit=1 - When the block is loaded from main-memory at first time.

• If the main-memory-block is updated by a source & if the block in the source
is already exists in the cache, then the valid-bit will be cleared to “0‟.
• If Processor & DMA uses the same copies of data then it is called as Cache
Coherence Problem.
• Advantages:

26
 Digital Design &Computer Organization(BCS302) MODULE -4
1) Contention problem of direct mapping is solved by having few choices for block
placement.

2) The hardware cost is decreased by reducing the size of associative search.

27
Digital Design &Computer Organization(BCS302) MODULE -4

28