Scribd
Upload
46 views4 pages

Engineering Graphics & Design

Important

Uploaded by

sachinkush1917
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
46 views4 pages

Engineering Graphics & Design

Important

Uploaded by

sachinkush1917
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

GTUSTUDY.

COM

Program Name: Engineering


Branch: All
Course / Subject Code : BE01000061
Course / Subject Name : Engineering Graphics & Design

Chapter 1: Introduction to Engineering Graphics


3-Mark Questions:

1. List the drawing instruments and their uses.

2. What is the significance of BIS – SP 46 standards in engineering drawing?

3. Define representative fraction and its application in engineering graphics.


4-Mark Questions:

1. Explain the use of plane and diagonal scales in engineering drawings.

2. Discuss the importance of proper dimensioning methods in technical drawings.


7-Mark Questions:

1. Prepare a neat diagram to show the construction and use of diagonal scales.

Chapter 2: Engineering Curves


3-Mark Questions:

1. Classify engineering curves and give one example of each type.

2. What are cycloidal curves? Mention one application.


4-Mark Questions:

1. Explain the construction of conics (parabola, ellipse, and hyperbola) with examples.

2. Discuss the steps to construct an involute of a circle.


7-Mark Questions:

VSIT :- https://gtustudy.com/ 1
GTUSTUDY.COM

1. Draw and explain the construction of a spiral curve.

Chapter 3: Projections of Points and Lines


3-Mark Questions:

1. What are the principal planes of projection?

2. Define true length and true inclination of a line.

4-Mark Questions:

1. Explain the projection of a line inclined to one reference plane.

2. Discuss the procedure for projecting a point located in different quadrants.


7-Mark Questions:

1. Solve a problem to find the true length and inclination of a line with reference planes.

Chapter 4: Projections of Planes


3-Mark Questions:

1. What are the types of planes commonly used in engineering drawings?

2. Write a short note on the projection of a circular plane.


4-Mark Questions:

1. Explain the projection of a polygonal plane inclined to one reference plane.

2. Discuss the steps to project an elliptical plane inclined to two reference planes.
7-Mark Questions:

1. Solve a numerical example to project a rectangular plane inclined to both reference


planes.

Chapter 5: Projections of Solids and Section of Solids


3-Mark Questions:

1. What are frustums of solids? Provide one example.

2. Define and classify solids based on their shapes.


4-Mark Questions:

VSIT :- https://gtustudy.com/ 2
GTUSTUDY.COM

1. Explain the projection of a cylinder with its axis inclined to one reference plane.

2. Discuss the method to find the true shape of the section of a cone.

7-Mark Questions:

1. Solve a problem to project a pyramid and determine the true shape of its section.

Chapter 6: Orthographic Projections


3-Mark Questions:

1. Define orthographic projection and its importance in engineering graphics.

2. Differentiate between first-angle and third-angle projection methods.


4-Mark Questions:

1. Explain the procedure to create orthographic views of an object.

2. Discuss the concept of sectional views in orthographic projection.


7-Mark Questions:

1. Draw the orthographic views (front, top, and side) of a given 3D object using the
firstangle projection method.

Chapter 7: Computer-Aided Drawing


3-Mark Questions:

1. List the basic AutoCAD commands for 2D drawing.

2. What is the purpose of the "Trim" and "Extend" commands in AutoCAD?


4-Mark Questions:

1. Explain the use of "Hatch" and "Chamfer" commands in AutoCAD with examples.

2. Discuss the procedure to set up a drawing template in AutoCAD.

7-Mark Questions:

1. Create a simple 2D orthographic drawing using AutoCAD commands (Line, Circle,


Rectangle, etc.).

VSIT :- https://gtustudy.com/ 3
GTUSTUDY.COM

The information contained in this document is provided "as is" for general information
purposes only. By choosing to read this PDF, you assume all risks associated with its content.
If you decide not to read or fully understand the material, that is your choice and
responsibility. The creators or distributors of this document bear no liability for
misunderstandings, omissions, or outcomes resulting from the decision not to engage with
its contents. Proceed at your own discretion.

VSIT :- https://gtustudy.com/ 4

You might also like