FL2000 Products

FL2000 System
Table of Contents
Introduction ....................................................................................................................1
Applications ..................................................................................................................2-6
Wall Mount Boxes - Empty ............................................................................................7
Wall Mount Boxes - Accessories ....................................................................................8
Rack or Cabinet Mount Panels - Empty
Termination Panel ....................................................................................................9
Splice Panel............................................................................................................10
Termination/Splice Panel ........................................................................................11
Value-Added Module Chassis ................................................................................12
Rack or Cabinet Mount Panels - Preconfigured
Termination Panel with Multifiber Cable ..........................................................13-14
Termination Panel with Pigtails ..............................................................................15
FL2000 System

Termination/Splice Panel with Pigtails ....................................................................16

Slack Storage Solutions
Fiber Storage Disk..................................................................................................17
Fiber Storage Tray ..................................................................................................17
Storage Deck Panel................................................................................................18
Horizontal Interbay Management Panel ................................................................18
6pak Adapter Plug-Ins
Loaded with adapters only ....................................................................................19
Loaded with adapters and pigtails ........................................................................20
Accessories
Locks ....................................................................................................................21
End Guards............................................................................................................21
Interbay Management Panel..................................................................................21
Lower Cable Troughs ............................................................................................21
803

Bonding/Grounding Kit..........................................................................................21
Cable/Clamp Kit ....................................................................................................21
Blank VCG ............................................................................................................21
FL2000 Fiber Frame
•

Network Rack ........................................................................................................22

12/00

Inner Interbay Management Panel ........................................................................22

Mounting Options ..................................................................................................23-27
Patch Cords ....................................................................................................................28
FasTerm™ Kit ..................................................................................................................29
Connector and Adapter Cleaning Kit ..........................................................................30
Index ..............................................................................................................................31

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0
 FL2000 System
Introduction

FL2000 Rack Mount

Termination Panel (Empty)

Single Fiber Access Swing-out Bulkhead Allows Full Access

The FL2000 System is a flexible, modular and economical series of fiber products
for today‘s and tomorrow‘s evolving communications and data networks.
FL2000 System

Features

• A complete line of modular panels and boxes, developed for cabinet, rack
and wall mounting.
• Fully adaptable for large or small main distribution frame (MDF),
intermediate distribution frame (IDF) or telephone closet (TC) applications.
• Designed for 19" (48.26 cm) EIA rack or cabinet environment found in FL2000 Rack Mount
many enterprise networks; optional brackets are available to accommodate Termination Panel
with IFC
23" (58.42 cm) or ETSI rack or cabinet mounting.
• Provides termination, splicing and storage capabilities for in-building cables,
outside plant cables and fiber optic terminal (FOT) equipment patch cords.
• Modular design offers maximum flexibility to satisfy both current needs
and future growth requirements.
• A full line of options and accessories ensures compatibility with existing
803

optical equipment.
• FL2000 systems accommodate the Value-Added plug-in modules, adding
flexibility and functionality to the optical transport systems. Splitters,
wavelength division multiplexers (WDMs) and other optical components FL2000 Rack Mount
•

can be easily incorporated. Termination/Splice Panel

(Empty)
12/00

• All FL2000 panels and boxes accommodate the modular FL2000 6pak
plug-ins. 6paks are available in all connector styles and can be ordered
as needed.
• ADC‘s patented removable angled retainers allow easy access for single
fiber maintenance.
• FL2000 panels and boxes feature superior vertical cable protection and
management.
• Rack mount panels are hinged on one side, allowing full access to the rear
of the front plate and the interior of the panel.
• Rack mount panels are equipped with mounting brackets to provide 5" 6pak Adapter Plug-Ins
(12.7 cm) recess mounting; mounting brackets are available for virtually any
mounting application.
• Rack mount panels can be wall mounted.
• The new FL2000 splice wheel allows easy roll-up of pigtail and buffer
tube lengths and superior bend radius protection.
• The FL2000 splice deck is available to complete existing installations.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 1
 FL2000 System
Applications

Interconnect Configuration
In an interconnect network, all outside plant (OSP) fibers are terminated at the back of the connector
module and all equipment patch cords are connected at the front. Interconnect installations are most
commonly found in small, price-sensitive and low-reconfiguration applications.

TO OSP
TO FIBER OPTIC
TERMINAL EQUIPMENT
OUTSIDE PLANT
CABLE(S) EQUIPMENT
PATCH CORDS
FL2000 System

OUTSIDE PLANT
CABLE(S)

EQUIPMENT
PATCH CORDS

Interconnect Configuration

Cross-Connect Configuration
In a cross-connect network, all OSP fibers and equipment terminations are terminated on the back of
the connector module. Patch cords are used at the front of the connector module to cross-connect OSP
fiber to the FOT equipment. The convenience and flexibility of the cross-connect system make it an
attractive method for managing your fiber plant. Cross-connect is the preferred installation for maximum
803

flexibility, simplified growth and cutovers, and protection of permanent connections.

EQUIPMENT TO FIBER OPTIC

PATCH CORDS
•

TRANSMISSION
EQUIPMENT
12/00

OUTSIDE PLANT
CABLE(S)

OSP

OSP EQUIPMENT
CABLE PATCH CORDS
FROM TO
OSP EQUIPMENT

CROSS-CONNECT
PATCH CORDS
CROSS-CONNECT
PATCH CORDS

Cross-Connect Configuration

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 2
 FL2000 System
Applications

Independent Service Provider Fiber Application

Fiber termination bays or fiber panels provide a central point for terminating incoming fibers. Fiber
jumpers, routed through a FiberGuide® protection system, connect the fiber termination bay to the
electronic equipment for optical to electronic conversion.

FiberGuide® Fiber Cable Management System Copper

Cabling
FL2000 System

Fiber Optic
Patch Cord

FIBER TERMINATION/ ELECTRICAL/OPTICAL

STORAGE BAY EQUIPMENT BAY

OUTSIDE PLANT
(OSP) FIBER SPLICE
803

ENCLOSURE
•
12/00

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 3
 FL2000 System
Applications

CATV Video Signal Path Through ADC Fiber Panel Products

1
®
FiberGuide Fiber Cable
Management System

3
Tx
4
2
FL2000
VAM
2 Panels
FL2000 System

Rx
FL2000 Intrafacility
Fiber Fiber Cable
3 Termination
Panel
5
6

8
7

9
Equipment
Rack or Cabinet

Fiber
Entrance
Cabinet
803

FL2000
Frame Outside
Plant
End Guard Cable
Interbay Management
•

Panel
12/00

CATV VIDEO SIGNAL PATH

Transmit Path Return Path
1 Video signal via coaxial cable 5 Optical video signal from
from video modulators. 1 Video signal from each node
outputs of splitters routed to the is jumpered from FL2000
2 ADC Homeworx™ transmit FL2000 termination connector termination panel to VAM
panel converts coax electrical module via fiber patch cord. chassis.
video signal to optical signal on 6 Intrafacility fiber cable (IFC)
fiber. Transmitter sends optical
2 6pak bulkhead on VAM
clamped and connected to rear connects fiber OSP patch cord
signal out. of fiber patch panel. to patch cord from upstream
3 Optical signal sent to the 7 IFC clamped to Fiber Entrance receiver.
splitters via a fiber optic patch Cabinet (FEC).
cord or pigtail. Splitters 3 Fiber patch cord from VAM
installed in FL2000 Value-Added 8 IFC fibers spliced to outside connects upstream signal to
Module (VAM). plant (OSP) fibers on FEC splice ADC Homeworx receive panel.
drawer. The receive panel converts
4 Splitter receives optical signal optical video signal to electrical
from transmitter and splits 9 OSP cable clamped to FEC.
and sends to network/ set-top
signal into several out paths control system via coaxial cable.
(1x2, 1x3, etc.). Each out path
serves one node.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 4
 FL2000 System
End User Fiber Application

Main Distribution Frame

FIBER BACKBONE COPPER BACKBONE

(RISER) CABLE (RISER) CABLE

IDF TC WORK
AREA

IDF WORK
AREA
FL2000 System

IDF TC WORK
AREA TO
(FROM)
PBX
ENTRANCE MDF
FACILITY PBX FIBER MDF (MC) AREA COPPER MDF (MC) AREA

The main distribution frame (MDF) area is generally the central point of interconnection between outside
plant (OSP) entrance cables and the in-building cabling distribution system. The MDF area is often used
as the point of demarcation between the local exchange carrier and the customer premises equipment.

Intermediate Distribution Frame

803

HORIZONTAL WIRING
TO WORK AREA
FIBER TIE CABLES
TO TC
COAX TIE CABLES
DATA GRADE TO TC
•

MPP
COPPER TIE CABLES
MODULAR TO TC
PATCH CORDS MPP
12/00

HUB
WORK
IDF TC
AREA FIBER OPTIC
PATCH CORDS FIBER
PANEL
IDF WORK
AREA VIDEO
DISTRIBUTION

IDF TC WORK
AREA

FIBER COPPER
BACKBONE AND COAX
ENTRANCE MDF
FACILITY PBX BACKBONES

The intermediate distribution frame (IDF) area is the point of interconnection between building backbone
cables and horizontal tie cable serving telephone closets or station wire serving the individual work locations.
IDFs usually serve a single floor and are typically arranged vertically in a building riser area. Electronic hub
equipment is normally installed within the IDF area because of the proximity to the backbone cabling. In
many cases, the IDF is the last connection point prior to the end workstation connection. In large
buildings, IDFs may serve multiple telephone closets (TCs) via tie cables.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 5
 FL2000 System
Applications

Telephone Closet

FIBER TIE CABLES

COPPER TIE CABLES

HORIZONTAL
COAX TIE WIRING
CABLES 2 INCH
FIBERGUIDE®
FIBER CABLE
IDF TC WORK MANAGEMENT
AREA SYSTEM
FIBER WALL
MOUNT BOX
IDF WORK
FL2000 System

110 AWI 300s

AREA
FOR COPPER
TERMINATIONS
IDF TC WORK
AREA Video
Distribution

ENTRANCE MDF
FACILITY PBX

The telephone closet (TC) is the point of interconnection between building cabling and horizontal station
wire serving the individual work locations. TCs usually serve a specific zone on a floor. Multiple TCs may be
served from single IDFs. The TC generally is the last connection point prior to the end workstation and may
not include electronic equipment.
803
•
12/00

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 6
 Wall Mount Boxes
Empty

Order the box and the 6paks separately for

Features field assembly:
• Terminate 12 or 24 fibers STEP 1.
• Constructed of economical, high strength Order empty 12 or 24 fiber wall boxes based on
polycarbonate the number of connectors/adapters required.
• Accommodate FL2000 6paks - FL2-12WBOX (12 fiber capacity wall mount box)
• Expansion kits available to convert - FL2-24WBOX (24 fiber capacity wall mount box)
12 fiber boxes to 24 fiber boxes STEP 2.
Order the required number of 6pak adapter
Fiber Panel Data
plug-ins to be placed in the wall box (see ordering
• Fiber Capacity: 12 or 24 information on pages 19-20).
• Termination
STEP 3.
FL2000 System

• Splice Order splice kits as needed (see ordering

• Pigtail Storage information on page 8).
• Wall Mount STEP 4.
Order vertical cable guides for added fiber
management and protection. The guides can be
installed on the right side of the wall box to cover
and protect the connector assembly.
803

FL2-12WBOX FL2-12GIDE FL2-24WBOX FL2-24GIDE

•
12/00

Ordering Information

Description Dimensions (HxWxD) Catalog Number

Wall Mount Boxes

12 fiber capacity 13.0" x 11.5" x 5.0" FL2-12WBOX
(33.02 x 29.21 x 12.7 cm)
24 fiber capacity 13.0" x 11.5" x 8.5" FL2-24WBOX
(33.02 x 29.21 x 21.59 cm)
Vertical Cable Guides
For 12 fiber wall box 13.0" x 5.0" x 5.0" FL2-12GIDE
(33.02 x 12.7 x 12.7 cm)
For 24 fiber wall box 13.0" x 5.0" x 8.5" FL2-24GIDE
(33.02 x 12.7 x 21.59 cm)

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 7
 Wall Mount Boxes
Accessories

Ordering Information

Description Catalog Number

6pak adapter plates, please see pages 19-20

Blank 6pak plates FL2-6PBLNK
Fill unused positions
Hubbel connector kit; includes one secure plate, one FL2-ACC001
Hubbel connector and one rubber grommet for
unused position
Hubbel connector, individual FIPM-ACC-HC Hubbel Connector Kit
Locks for wall mount boxes
Wall mount lock kit #1; includes internal mounting
FL2000 System

brackets, lock and key #1 FL2-ACC003

Wall mount lock kit #2; includes internal mounting
brackets, lock and key #2 FL2-ACC005
Locks for wall mount vertical cable guide
Key lock #1; includes lock and key #1 IPA-K1
Key lock #2; includes lock and key #2 IPA-K2
Splicing bracket kit
Locks
Adds 12 fiber splicing to wall boxes; includes mounting
bracket and one 12 fiber mini splice tray. For additional
splicing capacity (over 12 fibers), order one additional
mini splice tray
FibrLok® FL2-WSPLCE-3M
Bare fusion FL2-WSPLCE-FT
Heat shrink fusion FL2-WSPLCE-HS
Mechanical FL2-WSPLCE-MT
Rotary FL2-WSPLCE-RT
Nortel FL2-WSPLCE-NT
Mini Splice Tray
803

Mini splice trays

Expand wall boxes from 12 to 24 fiber splice
FibrLok® FST-M-3M
Bare fusion FST-M-FT
•

Heat shrink fusion FST-M-HS

Mechanical (Elastomeric) FST-M-MT
12/00

Rotary FST-M-RT
Nortel FST-M-NT
Rubber grommet kit (dust cover) – kit of 2 FL2-ACC002
Bonding/grounding kit – kit of 1 FL2-ACC006
Cable clamp kit – kit of 1
Outer diameter .2" to .8" FL2-ACC007 Rubber Grommet Kit
Outer diameter .7" to 1.0" FL2-ACC021
Wall box expansion ring
Expands a 12 fiber wall box to a 24 fiber capacity wall FL2-EXPKIT
box; assembly is required
Vertical cable guide expansion ring
Expands a 12 fiber vertical cable guide to a 24 fiber FL2-VCGEXP
vertical cable guide; assembly is required

Bonding/Grounding Kit

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 8
 Rack or Cabinet Mount Termination Panels
Empty Panels

Features
1.75" (4.45 cm) 8.75" (22.23 cm)
• Mounting
- 19" (48.26 cm) EIA rack or cabinets,
standard 5" (12.7 cm) recess
3.50" (8.89 cm)
- Wall mounting option available
- Other mounting kits available. 10.50" (20.67 cm)
Please see pages 23-27.
• Hinged on left front side1; allows full access to 5.25" (13.34 cm)

rear of front plate and interior of panel

• FL2000 6pak adapter plug-ins ordered separately
• Constructed of high strength aluminum
• Equipped with removable metal doors with
FL2000 System

Plexiglas windows
• Designation labels included with each panel
10.14" 19.60"
• Complete line of accessories including locks (25.76 cm) (49.79 cm)

for security
4.95"
Fiber Panel Data (12.58 cm) 5.25"
(13.34 cm)
• Fiber Capacity*: 12, 24, 36, 48, 72 & 96
• Termination
• Pigtail Storage

*All panels can double capacity with LX.5® adapters

Ordering Information

Description Panel Height Catalog Number1

803

Rack or Cabinet Mount Termination Panel

Includes vertical cable management trough 24 Fiber Capacity
12 fiber capacity 1.75" (4.45 cm) FL2-12RPNL
•

24 fiber capacity 3.50" (8.89 cm) FL2-24RPNL

36 fiber capacity 5.25" (13.34 cm) FL2-36RPNL
12/00

48 fiber capacity 5.25" (13.34 cm) FL2-48RPNL

72 fiber capacity 8.75" (22.23 cm) FL2-72RPNL
96 fiber capacity 10.50" (26.67 cm) FL2-96RPNL
Accessories
Wall mount bracket - FL2-ACC008
72 Fiber Capacity
Needed for 12 fiber capacity panel only
Cable clamp kit -
One per cable recommended
Outer diameter .2" to .8" FL2-ACC007
Outer diameter .7" to 1.0" FL2-ACC021
Cable clamp kit for 12 fiber capacity FL2-ACC033
panel only
Bonding/grounding kit FL2-ACC006
For mounting kits and additional 96 Fiber Capacity
accessories, see pages 21-27
1
Panels with right front hinge and VCG are also available, although they are not standard products.
To order a panel with right front hinge and VCG , add "-R" after the catalog number. Example: FL2-12RPNL-R.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 9
 Rack or Cabinet Mount Splice Panels
Empty Panels

19.60"
10.14"
Features (25.76 cm)
(49.79 cm)

• Offers combination of splicing protection and

associated fiber/pigtail storage 4.95"
(12.58 cm) 3.50"
• Splice panel can be mounted in conjunction (8.89 cm)
with any FL2000 termination panel or as a
stand-alone splice panel
• Occupies same footprint and offers same
mounting options as FL2000 termination panels
(see page 9)
• Accepts the new ADC splice wheel for efficient
management of fiber cable and splice protection
TOP
SIDE
• Accepts the traditional ADC splice deck
FL2000 System

CLEAR
Fiber Panel Data COVERS

• Fiber Capacity: 48, 96, 144

SPLICE
• Splice BOTTOM
SIDE DECK

• Pigtail Storage
SPLICE CHIP(S)
Splice Deck with (HEAT SHRINK
SHOWN)
Splice Chip
Splice Wheel with
Splice Chip
Ordering Information

Description Panel Height Catalog Number1

Splice Panel for Splice Wheel

(Accepts splice wheel only)
48 fiber capacity 3.5" (8.89 cm) FL2-48SPNL2
96 fiber capacity 7" (17.78 cm) FL2-96SPNL2
803

144 fiber capacity 8.75" (22.23 cm) FL2-144SPNL2

Splice Wheel with Splice Chip
Heat shrink fusion FST-DRS12-HS
Mechanical FST-DRS12-MT
•

Nortel FST-DRS24-NT
Splice Panel for Splice Deck for existing installations
12/00

(Also accepts splice wheel)

48 fiber capacity 3.5" (8.89 cm) FL2-48SPNL
96 fiber capacity 7" (17.78 cm) FL2-96SPNL
144 fiber capacity 8.75" (22.23 cm) FL2-144SPNL
Splice Deck with Splice Chip for existing installations
Heat shrink fusion FL2-RSPLCE-HS
Mechanical FL2-RSPLCE-MT
Bare fusion FL2-RSPLCE-FT
Nortel FL2-RSPLCE-NT
Cable Clamp Kit (kit of 1)
Outer diameter .2" to .8" FL2-ACC007
Outer diameter .7" to 1.0" FL2-ACC021
For mounting kits and additional
accessories, see page 21-27

1
Panels with right front hinge and VCG are also available, although they are not standard product. To order a panel
with right VCG, add "-R" after the catalog number. Example: FL2-48SPNL-R.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 10
 Rack or Cabinet Mount Termination/Splice Panels
Empty Panels

Features
• Mounting
- 19" (48.26 cm) EIA racks or cabinets,
standard 5" (12.7 cm) recess
- Wall mounting option available
- Other mounting kits available. Please see 24 Position
pages 23-27
• Hinged on left front side1 for complete access
to interior of termination section
• Ability to quickly and easily configure, utilizing
the 6pak assemblies (ordered separately)
FL2000 System

• Complete line of accessories including locks

for security
• Uses ADC splice wheels or splice decks
Fiber Panel Data
• Termination 48 Position
• Splice
• Pigtail Storage

19.60"
10.14" (49.79 cm)
(25.76 cm)

4.95" 5.25"
(12.58 cm) (13.34 cm)
803

96 Position
•

Ordering Information
12/00

Description Panel Height Catalog Number1

Termination/splice panel
12 position 3.5" (8.89 cm) FL2-12TS350
24 position 5.25" (13.34 cm) FL2-24TS525
48 position 8.75" (22.23 cm) FL2-48TS875
72 position 14" (35.56 cm) FL2-72TS140
96 position 17.5" (44.45 cm) FL2-96TS175
Splice Wheel with Splice Chip
Heat shrink fusion FST-DRS12-HS
Mechanical FST-DRS12-MT
Nortel FST-DRS24-NT
Splice Deck with Splice Chip
Heat shrink fusion FL2-RSPLCE-HS
Mechanical FL2-RSPLCE-MT
Bare fusion FL2-RSPLCE-FT
Nortel FL2-RSPLCE-NT
1
Panels with right front hinge and VCG are also available, although they are not standard product. To order a panel
with right front hinge and VCG, add "-R" after the catalog number.
Example: FL2-24TS525-R.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 11
 Value-Added Connector Module System
Empty Panels

Features Splitter Plug-in Modules

VAM Chassis • Mounted within variously-sized modules for
• Panel can be mounted in 5" (12.7 cm) recess splitting an optical input into many optical outputs
19" (48.26 cm) EIA racks or cabinets, standard; • Used for video and voice distribution in fiber-in-
other mounting kits available (please see the-loop (FITL) networks
pages 23-27). • Used for broadcast applications in CATV networks
• Match vertical cable management features of
existing FL2000 system Monitor Plug-in Modules

• Protect and manage optical components • Eliminate the need to disconnect patch cords to
test optical circuits
• Available in either 9-position, 6-position, or
4-position configurations • Provide reliable, easy access

• Purchased empty and can be loaded with • Couplers mounted within the plug-in module to
FL2000 System

different plug-in modules (which can be mixed provide nonintrusive monitoring point for testing
and matched) or blank plates • Each module designed to meet specific customer
• Only front facing modules can be used in the requirements for access and monitor capabilities
FL2000 VAM system Access Plug-in Modules
Wavelength Division Multiplexer Plug-In • Incorporate optical jack which allows intrusive
Module (WDM) access to the fiber
• VAM chassis accommodates WDM
components, enabling service providers to
double the amount of information transmitted
19.60"
by multiplexing two signals over a single fiber 10.14" (49.79 cm)
(25.76 cm)
• Used to achieve additional capacity when fibers
of an expanded route have been exhausted
• Allows service providers to make better use of
fiber that has been deployed as network grows 4.95"
and traffic patterns change (12.58 cm)

• Also employed to multiplex a video signal onto 5.25"

803

a voice circuit (13.34 cm)

FL2-4VAM525
•

Ordering Information
12/00

Description Panel Height (HxWxD) Catalog Number

VAM chassis
4 plug-in modules 5.25" x 19" x 10.14" FL2-4VAM525
(13.34 x 48.26 x 25.76 cm)
6 plug-in modules 7" x 19" x 10.14" FL2-6VAM700
(17.78 x 48.26 x 25.76 cm)
9 plug-in modules 10.5" x 19" x 10.14" FL2-9VAM105
(26.67 x 48.26 x 25.76 cm)

NOTE: The FL2000 VAM system is designed to accept only front access modules; i.e., all input and output
adapters, pigtails and/or bare fibers must be located on the front of the plug-in modules. For plug-in module
ordering information, call ADC Customer Service (1-800-366-3891) for a copy of the Value-Added Connector
Module System catalog.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 12
 Rack or Cabinet Mount Termination Panels
Preconfigured Panels with Multifiber Cable

Features
• Available with factory-installed multifiber
intrafacility cable (IFC) or OSP cable
• Panels with multifiber cable attached ship as a
single unit with cable clamp installed
• Panels come equipped with customer specified
number of adapters, retainers, connectors, cable
type and cable length
• Panels with multifiber cable attached save costly
installation time
• Simplifies ordering process by allowing one part
FL2000 System

number for the panel, adapters, connectors

and cable
• Multiple mounting styles available

Fiber Panel Data

• Termination
• Preloaded with Multifiber Cable
803
•
12/00

Ordering information appears on opposite page.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 13
 Rack or Cabinet Mount Termination Panels
Preconfigured Panels with Multifiber Cable

Catalog Number
0 __ __ __ __ __ - __ __ __ __
FL2 - __ __ __ __ 0

Panel Type
Latch Type
S Singlemode
M Multimode 0 Standard
1 Hole Plug
Nominal Capacity Panel Height 2 Screwdriver
1 12 position 1.75" (4.45cm) (1RU) 5 K1 Lock
2 24 position 3.5" (8.89 cm) (2RU) 6 K2 Lock
3 36 position 5.25" (13.34 cm) (3RU)
4 48 position 5.25" (13.34 cm) (3RU) Cable Exit Direction
FL2000 System

7 72 position 8.75" (22.23 cm) (5RU) U Up

9 96 position 10.5" (26.67 cm) (6RU) D Down

Connector Style Mounting Style2

Multimode A 19" (48.26 cm) standard
9 SC (19.6" [49.78 cm] overall)
D Duplex SC B 19" (48.26 cm) maximum
5 ST® (19" [48.26 cm] overall)
Y LX.5® C 19" (48.26 cm) flush mount
Singlemode D 23" (58.42 cm) centered
2 Ultra PCFC E 23" (58.42 cm) with oversized VCG
L FC with zirconia adapter F ETSI flush mount
F FC 8° angled polish
7 Ultra PCSC Length in Meters
N SC with zirconia adapter
XXX Cable Length (Meters)
J SC 8° angled polish
E Duplex SC
803

Cable Type
4 Ultra PCST
P ST® with zirconia adapter Multimode
K E-2000 8° angled polish C IFC Stranded 62.5/125
X LX.5®1 Singlemode
•

1 FC Hybrid (FC connector on front; A IFC Stranded Corning

12/00

SC connector on back of bulkhead) F Plenum Stranded

3 ST® Hybrid (ST® connector on front; G OSP Single Armor
SC connector on back of bulkhead) H Indoor-Outdoor
J OSP Dielectric
Cable Size K IFC Stranded Maxi-Strip
1 12 M IFC Ribbon
2 24 1 ®
LX.5 connectors and adapters double the capacity
3 36 of the panel by terminating two fibers at each adapter.
2
4 48 Mounting kit shipped unattached, if other than
7 72 standard mounting style.
9 96
A 144
Z 2 x 12 Please see pages 22-27 for mounting instructions.
Y 2 x 24
X 2 x 36
W 2 x 48

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 14
 Rack or Cabinet Mount Termination Panels
Preconfigured Panels with Pigtails

10.14" 19.60"
Features (25.76 cm) (49.79 cm)

FL2000 panels can also be shipped with 6paks

and/or pigtails pre-installed at the factory. 4.95"
(12.58 cm) 5.25"
• Reduce installation time (13.34 cm)

• Simplify ordering process

Use this configuration guide to determine the
catalog number right for your application.

Catalog Number
FL2000 System

FL2 - 0 0 - 0
1 2 3 4 5 6 7 8 9 10 11 12
Panel Type
R Termination only Number of
Nominal Capacity Panel Height Ports
Loaded
1 12 position 1.75" (4.45cm) (1U)
2 24 position 3.5" (8.89 cm) (2U)
Pigtail or Adapter Type
3 36 position 5.25" (13.34 cm) (3U)
4 48 position 5.25" (13.34 cm) (3U) A Adapters only
7 72 position 8.75" (22.23 cm) (5U) P 6 fiber softwall bundle (Corning)
9 96 position 10.5" (26.67 cm) (6U) H 6 fiber Maxi-Strip (Corning)
R 12 fiber ribbon2
Connector Style K 12 fiber softwall bundle (Corning)2
Multimode Y 12 fiber Maxi-Strip (Corning)2
9 SC
Mounting Style3
803

D Duplex SC
5 ST® A 19" (48.26 cm) standard
Y LX.5®1 (19.6" [49.78 cm] overall)
Singlemode B 19" (48.26 cm) maximum
•

2 Ultra PCFC (19" [48.26 cm] overall)

L FC with zirconia adapter C 19" (48.26 cm) flush mount
12/00

F FC 8° angled polish D 23" (58.42 cm) centered

7 Ultra PCSC E 23" (58.42 cm) with oversized VCG
N SC with zirconia adapter F ETSI flush mount
J SC 8° angled polish
E Duplex SC Latch Type
4 Ultra PCST
0 Latch
P ST® with zirconia adapter
1 Hole Plug
K E-2000 8° angled polish
2 Screwdriver
X LX.5®1
5 K1 Lock
1 FC Hybrid (FC connector on front;
6 K2 Lock
SC connector on back of bulkhead)
3 ST® Hybrid (ST® connector on front; Number of Cable Clamps
SC connector on back of bulkhead)
0 1 clamp (standard)
2 2 clamps

1 ®
LX.5 connectors and adapters double the capacity
of the panel by terminating two fibers at each adapter.
2 ®
For use with LX.5
3
Mounting kit shipped unattached, if other than
standard mounting style.

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 15
 Rack or Cabinet Mount Termination/Splice Panels
Preconfigured Panels with Pigtails

10.14" 19.60"
Features (25.76 cm) (49.79 cm)

FL2000 panels can also be shipped with 6paks

and/or pigtails pre-installed at the factory. 4.95"
(12.58 cm)
• Reduce installation time PNT1 5.25"
PNT1
(13.34 cm)
• Simplify ordering process
Use this configuration guide to determine the
catalog number right for your application.

Catalog Number
FL2000 System

FL2 - 0 -
1 2 3 4 5 6 7 8 9 10 11 12

Panel Type Number

C Termination/Splice of Ports Number of
Loaded Splice Decks Latch Type
0 Latch
Nominal Capacity Panel Height
1 Hole Plug
1 12 position 3.5" (8.89 cm) (2U) Pigtail or Adapter Type
2 Screwdriver
2 24 position 5.25" (13.34 cm) (3U) A Adapters only 5 K1 Lock
4 48 position 8.75" (22.23 cm) (5U) P 6 fiber softwall 6 K2 Lock
7 72 position 14.00" (35.56 cm) (8U) bundle (Corning)
9 96 position 17.50" (44.45 cm) (10U) H 6 fiber Maxi-Strip Number of Cable Clamps
(Corning) 0 1 clamp (standard)
Connector Style
R 12 fiber ribbon2
803

2 2 clamps
Multimode K 12 fiber softwall
9 SC bundle (Corning)2
D Duplex SC Mounting Style3
Y 12 fiber Maxi-
5 ST® Strip (Corning)2 A 19" (48.26 cm) standard
•

Y LX.5® 1 (19.6" [49.78 cm] overall)

12/00

Singlemode Splice Type B 19" (48.26 cm) maximum

2 Ultra PCFC (19" [48.26 cm] overall)
0 None or N/A
L FC with zirconia adapter C 19" (48.26 cm) flush mount
M Mechanical (Wheel)
F FC 8° angled polish D 23" (58.42 cm) centered
W Heat Shrink
7 Ultra PCSC E 23" (58.42 cm) with
Fusion (Wheel)
N SC with zirconia adapter oversized VCG
1 Bare Fusion (Deck)
J SC 8° angled polish F ETSI flush mount
2 Heat Shrink
E Duplex SC
Fusion (Deck)
4 Ultra PCST
3 Mechanical (Deck) 1 ®
LX.5 connectors and adapters double the
P ST® with zirconia adapter
7 Raychem capacity of the panel by terminating two
K E-2000 8° angled polish
Universal (Deck) fibers at each adapter.
X LX.5® 1 2 ®
For use with LX.5 only.
8 Nortel (Deck)
1 FC Hybrid (FC connector on front; 3
Mounting kit shipped unattached if other
SC connector on back of bulkhead) than standard mounting style.
3 ST® Hybrid (ST® connector on front; Splice Type2
SC connector on back of bulkhead) M Mechanical (Wheel)
N Nortel (Wheel)

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 16
 Slack Storage Solutions
Fiber Storage Disk
19.60"
10.14" (49.79 cm)
Features (25.76 cm)

• Provides jumper storage for 3mm patch cords –

4.95"
one patch cord per disk (12.58 cm)
• Stores 3.8 meters (12.5') of patch cord in
each disk
5.25"
Fiber Panel Data (13.34 cm)

• Patch Cord Storage

ROTATE TO
• Rack/Cabinet Mount REMOVE SLACK
FL2000 System

• Wall Mount

Ordering Information

Description Dimensions (HxWxD) Catalog Number

Fiber Storage Disk

16 disks 5.25" x 19" x 10.19" FL2-16FSD525
(13.34 x 48.26 x 25.81 cm)
24 disks 8.75" x 19" x 10.19" FL2-28FSD875
(22.23 x 48.26 x 25.81 cm)

Fiber Storage Tray

803

Features 19.60 in
10.18 in (49.79 cm)
• Provides jumper storage for 3mm patch cords (25.86 cm)
4.95 in
•

(12.58 cm)
• Stores 33 m (110') of patch cord in each tray
12/00

Fiber Panel Data 5.25 in

(13.34 cm)
• Patch Cord Storage
• Rack/Cabinet Mount

Ordering Information

Description Dimensions (HxWxD) Catalog Number

Fiber Storage Tray

6 Trays 5.25" x 19" x 10.19" FL2-CST60525
(13.34 x 48.26 x 25.81 cm)

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 17
 Slack Storage Solutions
Storage Deck Panel

Features 10.14"
19.60"
(49.79 cm)
(25.76 cm)
• Mounts with FL2000 termination panels
to provide jumper storage
4.95"
• Wall, Rack, or Cabinet Mount (12.58 cm)

• Utilizes unique storage decks for patch

cord storage 3.50"
(8.89 cm)
• Each storage deck accommodates up to
32 meters (105') of 3mm cable
FL2000 System

FL2000 Storage Deck Panel Front View

Ordering Information

Description Catalog Number

Storage deck panels

(storage decks ordered separately)
2 storage deck capacity; FL2-2RSTORE
3.5" x 19" x 10.19"
(8.89 x 48.26 x 25.81 cm) Storage Deck Top View
6 storage deck capacity; FL2-6RSTORE
8.75" x 19" x 10.19"
(22.23 x 48.26 x 25.81 cm)
Storage deck FL2-TR2000
803

Horizontal Interbay Management Panel

•

Features 4.95"
19.60"
• Mounts horizontally in a bay to manage (12.58 cm)
12/00

(49.79 cm)
jumper storage
• May be modified for flush or wall mount
applications 5.25"
(13.34 cm)

Ordering Information

Description Catalog Number

Horizontal interbay FL2-HZSTORE

management panel

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 18
 6pak Adapter Plug-Ins
For all FL2000 Termination Products

Features
• Completely interchangeable between
FL2000 panel and wall box products
• Can be ordered with all standard types of
6pak Plug-In (shown with
simplex and duplex single and multimode
singlemode duplex adapters)
adapters and connectors
• Feature ADC‘s patented removable angled
retainers which provide superior fiber
management
• No tools required to install into FL2000
boxes or panels
• Can be ordered with adapters only, or for
quick and easy installation, with 6pak Plug-In (shown with
FL2000 System

pre-terminated 3 meter (9.84') or 5 meter multimode duplex adapters)

(16.4') pigtails

6pak Blank Plug-In

6pak Plug-In (shown with

singlemode simplex adapters) Ordering Information

Description Catalog Number

Multimode
SC FL2-6PMMSC
ST® FL2-6PMMST
803

FC FL2-6PMMFC
6pak Plug-In (shown with
SC (duplex) FL2-6PMMDSC
mulitmode simplex adapters)
SC, zirconia FL2-6PMMSC-Z
ST®, zirconia FL2-6PMMST-Z
•

FC, zirconia FL2-6PMMFC-Z

12/00

LX.5® FL2-6PMMLX
Singlemode
SC FL2-6PSMSC
ST® FL2-6PSMST
FC FL2-6PSMFC
6pak Plug-In (shown with SC (duplex) FL2-6PSMDSC
singlemode LX.5® adapters) FC with 8° angled polish FL2-6PSMAFC
SC with 8° angled polish FL2-6PSMASC
SC, zirconia FL2-6PSMSC-Z
ST®, zirconia FL2-6PSMST-Z
FC, zirconia FL2-6PSMFC-Z
E-2000, angled polish FL2-6PSMAE-2
LX.5® FL2-6PSMALX
Hybrid: FC front, SC back FL2-6PSMFC/SC
Hybrid: ST® front, SC back FL2-6PSMST/SC
6pak Plug-In (shown with
multimode LX.5® adapters) 6pak blank plug-in FL2-6PBLNK

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 19
 6pak Connector Plug-Ins
With Adapters and Pigtails

Features
• Available with pre-terminated 3 meter (9.84')
or 5 meter (16.4') pigtails
• Pigtails consist of a single outer jacket
containing six color-coded 900 µm fibers
• One end of pigtail terminated to chosen
connector style and installed into the 6pak
plug-in adapters
• ADC recommends specific breakouts for panel
and wall mount box products
• Saves installation time FL2000 6pak plug-in
with SC adapters and pigtails
FL2000 System

Multimode Pigtails and Adapters

Catalog Number

B __
FL2 - 6P __ __ 6 __ __ __
C __
Multimode
Connector Style Length (in meters)
5 ST® 3 m (9.84') pigtail
03W
9 SC for wall mount boxes
A FC 5 m (16.4') pigtail
05R
D Duplex SC for rack mount panels
Y LX.5®1

Fiber Size 1
LX.5® 6paks are loaded with 12 fiber pigtails
B Multimode 62.5/125
803

C Multimode 50/125

Singlemode Pigtails and Adapters

•
12/00

Catalog Number

S __ __
FL2 - 6P __ __ 6 __ __ __
Singlemode
Connector Style Length (in meters)
E Duplex SC 3 m (9.84') pigtail
03W
2 Ultra PCFC for wall mount boxes
4 Ultra PCST 5 m (16.4') pigtail
05R
7 Ultra PCSC for rack mount panels
F PCFC 8° angled polish
Fiber Type
J PCSC 8° angled polish
K E-2000 angled polish C Corning
X LX.5®1 D Maxi-Strip (Corning)
Q PCSC 9° angled polish
1 FC Hybrid (FC connector on front;
SC connector on back of bulkhead) 1
LX.5® 6paks are loaded with 12 fiber pigtails
3 ST® Hybrid (ST® connector on front;
SC connector on back of bulkhead)

Fiber Size
S Singlemode

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 20
 Accessories for FL2000 Rack Mount Panels
RUBBER
GROMMETS
CLAMP
BRACKET

COVER

CLAMP NUTS (2)

YOKES (2) PLATE

Locks
Cable Clamp Kit

Interbay Management Panel

E-501-L139
FL2000 System

7'

Blank VCG Bonding/Grounding Kit

FL2-BLNKFULL0875
12"
2.5"
Ordering Information
End Guard
UEGP-7PW Description Catalog Number

Locks for rack mount panels

Key lock #1; includes lock and key #1 IPA-K1
Key lock #2; includes lock and key #2 IPA-K2
End guards
803

7' H x 12" W x 29/16" D; right or left side; UEGP-7PW

putty white
Interbay management panel
•

7' x 5"mounts to a standard 19" or 23" rack E-501-L139

Lower cable trough
12/00

14" H x 19" W x 5" D FL2-ACC011

7" H x 19" W x 5" D FL2-ACC012
Bonding/grounding kit – kit of 1 FL2-ACC006
14" Lower Cable Trough
Cable clamp kit – kit of 1
FL2-ACC011
Outer diameter .2" to .8" FL2-ACC007
Outer diameter .7 to 1.0" FL2-ACC021
Cable clamp kit – For use with 12 fiber FL2-ACC033
termination or termination/splice panels
Blank VCG to add cable management to frame
not fully loaded
3.5" (8.89 cm) FL2-BLNKVCG0350
8.75" (22.23 cm) FL2-BLNKVCG0875
10.5" (26.67 cm) FL2-BLNKVCG1050
Blank VCG with blank panel for aesthetics
3.5" (8.89 cm) FL2-BLNKFULL0350
5.25" (13.34 cm) FL2-BLNKFULL0525
7.0" (17.78 cm) FL2-BLNKFULL0700
8.75" (22.23 cm) FL2-BLNKFULL0875
7" Lower Cable Trough 10.5" (26.67 cm) FL2-BLNKFULL1050
FL2-ACC012

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 21
 FL2000 Fiber Frame
22.31"

Features 18.31"
44
An FL2000 fiber frame can be quickly and easily
configured to fulfill a particular application‘s FL2-
40
requirements. BLNKFULL1050

FL2-INIMP-22RU
• FL2000 components are designed to allow the 38.5" INNER-IMP (2)
customer to quickly assemble a fiber frame at 35
their location.
• ADC will assemble a loaded fiber frame at the
30
customer‘s request.

Components may include:

25
• Termination panels
FL2000 System

• Splice panels 7'

20
• Preconfigured panels with pigtails
• Value-added modules
• Storage 15

FL2-24RPNL

10

1.75"
Ordering Information 14" LHCT
5

Description Catalog Number

Network Rack
4.75"
7'H x 19"W PWUEF-7X19ERN
(214 cm x 48.2 cm) 21.50"

7'H x 23"W PWUEF-7ERN 25.88"

(214 cm x 58.42 cm) PWUEF-7ERN FRONT VIEW

803

NETWORK RACK
Contact ADC‘s Technical Assistance Center (1-800-366-3891) to
configure a loaded fiber frame. Typical Frame Application
Using FL2000 Frame, IMP and End Guard
•

Inner Interbay Management Panel

12/00

Features
• The FL2000 inner interbay management panel 22.312 REF
allows you to convert a 23" (58.42 cm) EIA rack
to a 19" (48.26 cm) EIA mounting 18.312 REF
ASSEMBLE INNER-INTERBAY
environment and provide slack storage. MANAGEMENT PANEL (2 SHOWN)
USING RACK MOUNT SCREW

Ordering Information

Description Catalog Number

Inner interbay management FIBER CABLE

five spools, length: MANAGEMENT SPOOLS
29.75" (75.57 cm) FL2-INIMP-17RU EIA HOLE
35" (88.9 cm) FL2-INIMP-20RU SPACING
38.5" (97.79 cm) FL2-INIMP-22RU
Inner interbay management FL2-INIMPCVR-22RU
3" FRAME
cover fits 22RU (38.5" long)

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 22
 Mounting Options
19" (48.26 cm) Rack Mounting

Standard Mount (as shipped)

Rear Guard Box Rack shown
(optional with some racks) for reference
Features 21.88"
(55.58 cm)
• Panels typically shipped from factory equipped 18.31"
17.50" (46.51 cm)
for this mounting (44.45 cm)

• Panels shipped with

- Left-side "L" bracket
5.00" 5.00"
- Left-side 2.5" (6.32 cm) wide vertical (12.70 cm) (12.70 cm)
cable guide (VCG)
FL2000 System

19.60"
(48.26 cm)

Flush Mount
18.83"
(47.82 cm)
17.50"
(44.45 cm)
Rear Guard Box 15.912"
(optional with some racks) (40.42 cm)

Rack shown
1.94" as reference
(4.93 cm)

6.65"
(16.89 cm)
5.00"
5.00" (12.70 cm)
(12.70 cm)
803

Ordering Information
•

Description Panel Height Catalog Number

12/00

Flush Mount 1.75" (4.45 cm) FL2-FLMT0175

Allows 1", 2" or 4" (2.54, 5.08 or 10.16 cm) 3.5" (8.89 cm) FL2-FLMT0350
recess mounting 5.25" (13.34 cm) FL2-FLMT0525
Kit includes: new vertical cable guide and 7" (17.78 cm) FL2-FLMT0700
mounting flanges 8.75" (22.23 cm) FL2-FLMT0875
10.5" (26.67 cm) FL2-FLMT1050

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 23
 Mounting Options
19" (48.26 cm) Rack Mounting

19" Maximum Mounting

21.88"
(55.58 cm)
19.00
(48.26 cm)
18.31"
(46.51 cm)
REAR GUARD BOX 17.50" RACK SHOWN
(OPTIONAL WITH SOME RACKS) (44.45 cm)
FOR REFERENCE

5.00" 5.00"
(12.70 cm) (12.70 cm)
2.93"

10.14"
(25.76 cm)
FL2000 System

4.95"
(12.58 cm)

New VCG with integrated mounting holes

Ordering Information

Description Panel Height Catalog Number

19" Maximum 1.75" (4.45 cm) FL2-19MAX0175

Allows entire panel to be contained 3.5" (8.89 cm) FL2-19MAX0350
within frame footprint 5.25" (13.34 cm) FL2-19MAX0525
Kit includes: new vertical cable guide 7" (17.78 cm) FL2-19MAX0700
with integrated mounting holes 8.75" (22.23 cm) FL2-19MAX0875
10.5" (26.67 cm) FL2-19MAX1050
14" (35.56 cm) FL2-19MAX1400
17.5" (43.18 cm) FL2-19MAX1750
803
•
12/00

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 24
 Mounting Options
23" (58.42 cm) Rack Mounting

23" Wide VCG Mounting

25.88"
Rear Guard Box (65.74 cm)
21.50"
(optional with (54.61 cm)
some racks) Rack shown
for reference

5.00" 5.00"
(12.70 cm) (12.70 cm)
FL2000 System

22.31"
(56.67 cm)

23" Wide VCG Mounting

Ordering Information

Description Panel Height Catalog Number

23" with Large VCG 1.75" (4.45 cm) FL2-23VCG0175

Kit includes: new vertical cable guide 3.5" (8.89 cm) FL2-23VCG0350
with integrated mounting holes 5.25" (13.34 cm) FL2-23VCG0525
7" (17.78 cm) FL2-23VCG0700
8.75" (22.23 cm) FL2-23VCG0875
10.5" (26.67 cm) FL2-23VCG1050
14" (35.56 cm) FL2-23VCG1400
803

17.5" (43.18 cm) FL2-23VCG1750

•
12/00

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 25
 Mounting Options
23" (58.42 cm) Rack Mounting

Inner IMP Mounting

Note: Standard mounting in a rack equipped with inner-IMP

25.88"
(65.74 cm)
22.31"
Rear Guard Box (56.67 cm)
(optional with 21.50"
some racks) (54.61 cm) Rack shown
for reference

5.00" 5.00"
(12.70 cm) (12.70 cm)

IMP
FL2000 System

18.31"
(46.51 cm)

23" (58.42 cm) Centered (Extender Bracket Mounting)

25.88"
(65.74 cm)
Rear Guard Box 22.31"
(optional with 21.50" (56.67 cm)
Rack shown
some racks) (54.61 cm) for reference

5.00" 5.00"
(12.70 cm) (12.70 cm)
803

Extender Bracket Extender Bracket

18.31"
•

(46.51 cm)
12/00

Ordering Information

Description Panel Height Catalog Number

23" Rack Centered 1.75" (4.45 cm) FL2-EB0175P

(with extender brackets) 3.5" (8.89 cm) FL2-EB0350P
This kit can be used with flush mount 5.25" (13.34 cm) FL2-EB0525P
brackets (see page 23) to achieve 23" 7" (17.78 cm) FL2-EB0700P
flush mounting, as well as 1", 2", or 4" 8.75" (22.23 cm) FL2-EB0875P
recess mounting 10.5" (26.67 cm) FL2-EB1050P
14" (35.56 cm) FL2-EB1400P
17.5" (43.18 cm) FL2-EB1750P

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 26
 Mounting Options
19" ETSI Mounting

21.88"
(55.58 cm)
21.22"
(53.99 cm)
20.276"
(51.50 cm)

3.02"
(7.67 cm)

5.00"
(12.70 cm) 5.00"
(12.70 cm)
4.85"
(12.32 cm)
FL2000 System

Ordering Information

Description Panel Height Catalog Number

19" ETSI Mounting 1.75" (4.45 cm) FL2-ETEB0175

Kit includes mounting brackets 3.5" (8.89 cm) FL2-ETEB0350
5.25" (13.34 cm) FL2-ETEB0525
7.0" (17.78 cm) FL2-ETEB0700
8.75" (22.23 cm) FL2-ETEB0875
10.5" (26.67 cm) FL2-ETEB1050
14" (35.56 cm) FL2-ETEB1400
17" (43.18 cm) FL2-ETEB1700
803
•
12/00

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 27
 Patch Cords
Ultra Physical Contact Fiber Optic Patch Cords
Singlemode and Multimode

Catalog Number

___ ___ -___ -___ -___ M

Length (in meters)

Cable/Fiber Option
FPC Corning fiber: S Singlemode
connector on both ends A Multimode 50/125
(patch cord) B Multimode 62.5/125
FL2000 System

FPT Corning fiber:

connector on one end Singlemode Connector Type**
(pigtail) SPFC Ultra PCFC
SPST Ultra PCST
Special Cable/Fiber SPSC Ultra PCSC
LEAVE APFC PCFC 8° Angled Polish
BLANK 3 mm Single APSC PCSC 8° Angled Polish
Z 3 mm Dual zip* AE2 E-2000 Angled Polish
M 2 mm Single ALX5 LX.5®
2 2 mm Dual zip*
OR
F 1.7 mm Single
Multimode Connector Type**
T 1.7 mm Dual zip*
MFC FC
9 900 micron cable
MST ST®
MSC SC
* Standard breakout is 45.72 cm. Contact your
MDSC Duplex SC
ADC representative for additional breakout options.
Requires Dual zip
**For hybrid patch cords, enter both connector MLX5 LX.5®
types in this field. Separate them with a slash mark.
803
•
12/00

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 28
 FasTerm™ for LX.5®, SC and ST ® Connectors
Ordering Information

Description Catalog Number

Multimode FasTerm™ Connectors

LX.5® connector FTC-LXM111
SC connector FTC-SCM111
ST® connector FTC-STM111
Singlemode FasTerm™ Connectors
SC connector FTC-SCS111
ST® connector FTC-STS111
FC connector FTC-FCS111
FasTerm™ Tool Kits
FL2000 System

Multimode LX.5® tool kit FTC-LXKIT001

Singlemode SC tool kit* FTC-KIT002-SC
Singlemode ST® tool kit* FTC-KIT002-ST
Singlemode FC tool kit* FTC-KIT002-FC
Accessories
Multimode consumables kit (100 terminations); FTC-CNSM01
connectors not included
Singlemode consumables kit (100 terminations); FTC-CNSM02
connectors not included
Multimode LX.5® consumables kit FTC-CNSM04
Multimode duplex SC connector clip (attaches 2 FBA-DCLIP-M
FasTerm™ SC connectors for duplex requirements)
Singlemode duplex SC connector clip (attaches 2 FBA-DCLIP-S
FasTerm™ SC connectors for duplex requirements)

*Each tool kit is identical except for the polishing puck. Additional pucks may be
purchased to expand the capabilities of a singlemode kit.
803
•
12/00

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 29
 Fiber Connector/Adapter Cleaning Kit

The fiber connector/adapter cleaning kit contains

all the items required to adequately clean fiber
connectors and adapters. The performance of an
optical fiber system is largely dependent on the
fiber connector cleaning procedures followed prior
to installation. It is suggested that all the connec-
tors and adapters be cleaned before making any
connections. This kit contains an instruction sheet,
lint-free wipes, isopropyl alcohol, cotton swabs,
lint-free pipe cleaners and oil-free compressed air.
The kit cleans approximately 500 connectors
FL2000 System

and/or adapters.

Ordering Information

Description Catalog Number

Fiber connector/adapter cleaning kit FPC-CLNKIT

803
•
12/00

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 30
 FL2000 System
Index

E FL2-6PSMFC ............................................................19
E-501-L139 ..............................................................21 FL2-6PSMFC-Z ..........................................................19
FL2-6PSMFC/SC........................................................19
F FL2-6PSMSC ............................................................19
FBA-DCLIP-M............................................................29 FL2-6PSMSC-Z..........................................................19
FBA-DCLIP-S ............................................................29 FL2-6PSMST..............................................................19
FIPM-ACC-HC ............................................................8 FL2-6PSMST-Z ..........................................................19
FL2-12GIDE ................................................................7 FL2-6PSMST/SC ........................................................19
FL2-12RPNL ................................................................9 FL2-6RSTORE ............................................................18
FL2-12TS350 ............................................................11 FL2-6VAM700 ..........................................................12
FL2-12WBOX..............................................................7 FL2-72RPNL ................................................................9
FL2-144SPNL ............................................................10 FL2-72TS140 ............................................................11
FL2-144SPNL2 ..........................................................10 FL2-96RPNL ................................................................9
FL2000 System

FL2-16FSD525 ..........................................................17 FL2-96SPNL ..............................................................10

FL2-19MAX0175 ......................................................24 FL2-96SPNL2 ............................................................10
FL2-19MAX0350 ......................................................24 FL2-96TS175 ............................................................11
FL2-19MAX0525 ......................................................24 FL2-9VAM105 ..........................................................12
FL2-19MAX0700 ......................................................24 FL2-ACC001 ..............................................................8
FL2-19MAX0875 ......................................................24 FL2-ACC002 ..............................................................8
FL2-19MAX1050 ......................................................24 FL2-ACC003 ..............................................................8
FL2-19MAX1400 ......................................................24 FL2-ACC005 ..............................................................8
FL2-19MAX1750 ......................................................24 FL2-ACC006 ..................................................8, 9, 21
FL2-23VCG0175 ......................................................25 FL2-ACC007 ..........................................8, 9, 10, 21
FL2-23VCG0350 ......................................................25 FL2-ACC008 ..............................................................9
FL2-23VCG0525 ......................................................25 FL2-ACC011 ............................................................21
FL2-23VCG0700 ......................................................25 FL2-ACC012 ............................................................21
FL2-23VCG0875 ......................................................25 FL2-ACC021 ..........................................8, 9, 10, 21
FL2-23VCG1050 ......................................................25 FL2-ACC033 ........................................................9, 21
FL2-23VCG1400 ......................................................25 FL2-BLNKVCG0350 ..................................................21
FL2-23VCG1750 ......................................................25 FL2-BLNKVCG0875 ..................................................21
FL2-24GIDE ................................................................7 FL2-BLNKVCG1050 ..................................................21
803

FL2-24RPNL ................................................................9 FL2-BLNKFULL0350 ..................................................21

FL2-24TS525 ............................................................11 FL2-BLNKFULL0525 ..................................................21
FL2-24WBOX..............................................................7 FL2-BLNKFULL0700 ..................................................21
FL2-28FSD875 ..........................................................17 FL2-BLNKFULL0875 ..................................................21
•

FL2-2RSTORE ............................................................18 FL2-BLNKFULL1050 ..................................................21

12/00

FL2-36RNPL ................................................................9 FL2-CST60525..........................................................17

FL2-48RPNL ................................................................9 FL2-ETEB0175 ..........................................................27
FL2-48SPNL ..............................................................10 FL2-ETEB0350 ..........................................................27
FL2-48SPNL2 ............................................................10 FL2-ETEB0525 ..........................................................27
FL2-48TS875 ............................................................11 FL2-ETEB0700 ..........................................................27
FL2-4VAM525 ..........................................................12 FL2-ETEB0875 ..........................................................27
FL2-6PBLNK ........................................................8, 19 FL2-ETEB1050 ..........................................................27
FL2-6PMMDSC ........................................................19 FL2-CST60525..........................................................17
FL2-6PMMFC............................................................19 FL2-ETEB1400 ..........................................................27
FL2-6PMMFC-Z ........................................................19 FL2-ETEB1700 ..........................................................27
FL2-6PMMLX............................................................19 FL2-EB0175P ............................................................26
FL2-6PMMSC ..........................................................19 FL2-EB0350P ............................................................26
FL2-6PMMSC-Z ........................................................19 FL2-EB0525P ............................................................26
FL2-6PMMST ............................................................19 FL2-EB0700P ............................................................26
FL2-6PMMST-Z..........................................................19 FL2-EB0875P ............................................................26
FL2-6PSMAE-2..........................................................19 FL2-EB1050P ............................................................26
FL2-6PSMAFC ..........................................................19 FL2-EB1400P ............................................................26
FL2-6PSMALX ..........................................................19 FL2-EB1750P ............................................................26
FL2-6PSMASC ..........................................................19 FL2-EXPKIT ................................................................8
FL2-6PSMDSC ..........................................................19 FL2-FLMT0175..........................................................23

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 31
 FL2000 System
Index

FL2-FLMT0350..........................................................23
FL2-FLMT0525..........................................................23
FL2-FLMT0700..........................................................23
FL2-FLMT0875..........................................................23
FL2-FLMT1050..........................................................23
FL2-HZSTORE............................................................18
FL2-INIMP-17RU ......................................................22
FL2-INIMP-20RU ......................................................22
FL2-INIMP-22RU ......................................................22
FL2-INIMPCUR-22RU ................................................22
FL2-RSPLCE-FT....................................................10, 11
FL2-RSPLCE-HS ..................................................10, 11
FL2-RSPLCE-MT ..................................................10, 11
FL2000 System

FL2-RSPLCE-NT ..................................................10, 11
FL2-TR2000 ..............................................................18
FL2-VCGEXP ..............................................................8
FL2-WSPLCE-3M ........................................................8
FL2-WSPLCE-FT ..........................................................8
FL2-WSPLCE-HS..........................................................8
FL2-WSPLCE-MT ........................................................8
FL2-WSPLCE-NT..........................................................8
FL2-WSPLCE-RT ..........................................................8
FPC-CLNKIT ..............................................................30
FST-DRS12-HS ....................................................10, 11
FST-DRS12-MT....................................................10, 11
FST-DRS24-NT ....................................................10, 11
FST-M-3M ..................................................................8
FST-M-FT ....................................................................8
FST-M-HS....................................................................8
FST-M-MT ..................................................................8
FST-M-NT....................................................................8
803

FST-M-RT ....................................................................8
FTC-CNSM01 ..........................................................29
FTC-CNSM02 ..........................................................29
FTC-CNSM04 ..........................................................29
•

FTC-FCS111..............................................................29
12/00

FTC-KIT002-FC ........................................................29
FTC-KIT002-SC ........................................................29
FTC-KIT002-ST..........................................................29
FTC-LXKIT001 ..........................................................29
FTC-LXM111 ............................................................29
FTC-SCM111............................................................29
FTC-SCS111 ............................................................29
FTC-STM111 ............................................................29
FTC-STS111 ..............................................................29

I
IPA-K1 ................................................................8, 21
IPA-K2 ................................................................8, 21

P
PWUEF-7ERN............................................................22
PWUEF-7X19ERN......................................................22

U
UEGP-7PW ..............................................................21

w w w . a d c . c o m • + 1 - 9 5 2 - 9 3 8 - 8 0 8 0 32
Web Site: www.adc.com
From North America, Call Toll Free: 1-800-366-3891 • Outside of North America: +1-952-938-8080 Fax: +1-952-946-3292
For a complete listing of ADC‘s global sales office locations, please refer to our web site.
ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, Minnesota USA 55440-1101
Specifications published here are current as of the date of publication of this document. Because we are continuously improving our
products, ADC reserves the right to change specifications without prior notice. At any time, you may verify product specifications by
contacting our headquarters office in Minneapolis. ADC Telecommunications, Inc. views its patent portfolio as an important corporate
asset and vigorously enforces its patents. Products or features contained herein may be covered by one or more U.S. or foreign patents.

803 12/00 Revision © 1994, 1996, 2000 ADC Telecommunications, Inc. All Rights Reserved An Equal Opportunity Employer