FAA-2019-0486-0005_attachment_4
FAA-2019-0486-0005_attachment_4
FAA-2019-0486-0005_attachment_4
SERVICE BULLETIN
CONF ALL
AIRBUS S.A.S.
Customer Services
Technical Data Support and Services
31703 Blagnac Cedex
FRANCE
- Transform Service Bulletin data from ATA iSpec 2200 norm to ASD S1000D norm
- Update the dimensions of the Threaded Pins
- Add an Additional Work Task for aircraft modified by the original issue of this Service
Bulletin.
C. CHANGES
CONF 001
SERVICE BULLETIN
General Revised text and layout changes of this revision are
not identified with revision bars.
CONF 002
SERVICE BULLETIN
General Revised text and layout changes of this revision are
not identified with revision bars.
CONF 003
SERVICE BULLETIN
General Revised text and layout changes of this revision are
not identified with revision bars.
CONF 004
SERVICE BULLETIN
General Revised text and layout changes of this revision are
not identified with revision bars.
CONF ALL
D. FILING INSTRUCTIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 160417K30483
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.
CONF 002
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 160417K30483
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.
CONF 003
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 160417K30483
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.
CONF 004
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 160417K30483
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting
the airworthiness of the product. All other changes are major changes.
NOTE: This modification related to an Airworthiness issue has been classified by Airbus
and confirmed by EASA as minor in accordance with EU Part 21.A.91. As such, this
minor change is handled by Airbus under its Design Organisation Approval No.
EASA.21J.031.
CONF ALL
B. REASON
(1) History
Several operators have reported loose or missing screws at the X-brackets, Y-
brackets and connecting plates of their Over Head Stowage Compartments (OHSC).
Investigations and a sampling program have shown that fuselage deflections (due
to pressure and temperature differences caused during a regular flight cycle) lead
to loads on the secondary X-load path in the OHSC. This is the root cause of the
screws loosening. The aircraft affected by this Service Bulletin are equipped with the
Enhanced Cabin configuration.
(2) Objective/Action
This Service Bulletin replaces the current screws in the X-brackets, Y-brackets and
connecting plates with threaded pins with applied micro-encapsulated coating and
additional self-locking nuts.
(3) Advantages
The embodiment of this Service Bulletin will improve the robustness of the OHSC
fixation system thus avoiding further unscheduled maintenance in this area.
(4) Operational/Maintenance Consequences
None
C. GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE MANDATORY COST SAVING No
A/C OPERATION NO VENDOR SB NO
AFFECTED
CANCELS INSPECTION SB NO ETOPS AFFECTED NO
PAX COMFORT AFFECTED NO POTENTIAL AD YES
RELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NO
LIFE LIMIT NO LINE MAINTENANCE AFFECTED NO
D. MAINTENANCE CONFIGURATION
CONF 001
No specific aircraft maintenance configuration required.
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 5
A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
CONF 002
No specific aircraft maintenance configuration required.
CONF 003
No specific aircraft maintenance configuration required.
CONF 004
No specific aircraft maintenance configuration required.
CONF ALL
E. MATERIAL PRICE INFORMATION
CONF 001
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
CONF 002
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
CONF 003
CONF 004
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
CONF ALL
F. APPLICABILITY
This Service Bulletin is applicable to this (these) operator(s):
15T 16T 17M 17R 20Q 31X 34L 41N 45O 46U 48O 74T 84M 89X 95V 95W 96Q AAF AAL AAR
AAW AAY ABL ABQ ABY ACA ACI ADR AEE AFL AFR AHY AIC AIJ ALK AMC AMU ANA ANZ APJ
ASL ASV AUA AVA AWC AXM AZA BAW BEC BEG BEL BGF BGH BJN BKP BTK BTN C2C CBG
CBJ CCA CCM CDC CEB CES CFG CGH CHB CQH CQN CRK CSA CSC CSN CSZ CTV DKH DLH
DRK DSM EIN ELB ETD EVA EVE EWE EWG EZY F2I FAD FCB FFT FHY FIA FIN FLI FOO GAF
GAP GCR GFA GLG GMI GOW GSW GWI HDA HIM HKE HVN HXA IAW IBE IBS IGO IRA ISR IYE
JAT JBU JCC JJP JOC JSA JST JZR KAC KAY KHV KKK KME KNE KZR LAA LAN LAO LBT LDM LGW
LKE LLC LLP LZB MAC MEA MJF MJN MKR MLM MSC NIA NKS NLY NMB NVD NWS ONE ORF
AIRCRAFT YES
EQUIPMENT NO
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
AIRCRAFT YES
EQUIPMENT NO
CONF 002
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT NO
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
AIRCRAFT YES
EQUIPMENT NO
CONF 003
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
AIRCRAFT YES
EQUIPMENT NO
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
AIRCRAFT YES
EQUIPMENT NO
CONF 004
(1) Modification
AIRCRAFT YES
EQUIPMENT NO
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
AIRCRAFT YES
EQUIPMENT NO
CONF ALL
I. MANPOWER
CONF 001
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 36.00 h
ELAPSED TIME (HOURS) 13.00 h
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
MANPOWER
TOTAL MAN-HOURS 18.25 h
ELAPSED TIME (HOURS) 8.75 h
CONF 002
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 36.00 h
ELAPSED TIME (HOURS) 13.00 h
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
MANPOWER
TOTAL MAN-HOURS 18.25 h
ELAPSED TIME (HOURS) 8.75 h
CONF 003
(1) Modification
MANPOWER
TOTAL MAN-HOURS 38.00 h
ELAPSED TIME (HOURS) 13.50 h
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
MANPOWER
TOTAL MAN-HOURS 18.50 h
ELAPSED TIME (HOURS) 9.00 h
CONF 004
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
MANPOWER
TOTAL MAN-HOURS 42.00 h
ELAPSED TIME (HOURS) 14.50 h
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
MANPOWER
TOTAL MAN-HOURS 19.00 h
ELAPSED TIME (HOURS) 9.50 h
Z260
Z250
Z240
Z230
FR66
A
TYPICAL A320
FAMILY AIRCRAFT
FR21
NOTE:
AREA OF MODIFICATION
ICN-A320-A-25XX1BGK-A-FAPE3-000C2-A-001-01
ATA SYSTEM: 25
NOTE: This Service Bulletin is only applicable to aircraft on which MOD No. 35812K10500
(Enhanced Cabin) has been embodied.
NOTE: This Service Bulletin is applicable to aircraft on which MOD No. 156667K17239 or
MOD No. 151060K13968 (Service Bulletin No. A320-25-1B60 or Service Bulletin No.
A320-25-1677) is/are embodied.
NOTE: This modification is embodied before delivery on A319 aircraft with Manufacturer
Serial Number (MSN) 07880 and subsequent.
NOTE: This modification is embodied before delivery on A320 aircraft with Manufacturer
Serial Number (MSN) 07863 thru 07904, 07906, 07910 and subsequent.
NOTE: This modification is embodied before delivery on A321 aircraft with Manufacturer
Serial Number (MSN) 07852, 07857 thru 07865, 07872 thru 07884, 07888 thru
07894, 07898 thru 07940, 07947 thru 07970, 07976 thru 08003, 08032 thru
08034, 08041 thru 08062, 08069 thru 08076, 08104 and subsequent.
(1) Models
ON A/C 4007, 4039, 5545
318-112
ON A/C 3635
318-121
ON A/C 3030, 3062, 3214, 3216, 3371, 3390, 3469, 3509, 3585, 3602, 3606, 3642
318-122
ON A/C 3281, 3298, 3336, 3364, 3380, 3403, 3411, 3413, 3426, 3432, 3442, 3443, 3466,
3537, 3544, 3555, 3569, 3571, 3608, 3615, 3634, 3651, 3657, 3675, 3683, 3702, 3720,
3735, 3742, 3744, 3746, 3754, 3763, 3774, 3788, 3794, 3799, 3808, 3810, 3824, 3838,
3844, 3845, 3854, 3888, 3942, 3998, 4004, 4040, 4048, 4056, 4069, 4076, 4080, 4087,
4125, 4129, 4132, 4313, 4327, 4380, 4385, 4418, 4425, 4427, 4437, 4444, 4451, 4624,
4635, 4640, 4667, 4693, 4705, 4717, 4744, 4759, 4764, 4778, 4781, 4785, 4787, 4837,
4859, 4875, 4910, 5018, 5130, 5294, 5383, 5424
319-111
ON A/C 3019, 3096, 3139, 3171, 3181, 3188, 3202, 3204, 3245, 3271, 3285, 3288, 3300,
3305, 3309, 3324, 3331, 3344, 3346, 3347, 3377, 3385, 3388, 3406, 3407, 3415, 3417,
3436, 3445, 3447, 3452, 3533, 3551, 3560, 3564, 3586, 3589, 3604, 3620, 3660, 3661,
3684, 3686, 3687, 3689, 3700, 3704, 3727, 3728, 3733, 3790, 3818, 3822, 3834, 3853,
3865, 3872, 3874, 3892, 3895, 3905, 3918, 3950, 3970, 3983, 4020, 4029, 4038, 4052,
4071, 4089, 4121, 4127, 4141, 4164, 4182, 4258, 4268, 4275, 4332, 4455, 4511, 4663,
4691, 4713, 4734, 4756, 4796, 4841, 4871, 5005, 5085, 5097, 5239, 5284, 5293, 5366, 5400
319-112
ON A/C 3168, 3186, 3467, 3518, 3647, 3691, 3828, 3903, 3957, 3994, 4024, 4200, 4204,
4222, 4228, 4254, 4287, 4336, 4353, 4470, 4622, 4679, 4766, 4768, 4801, 4822, 4846,
4956, 5023, 5040, 5057, 5079, 5088, 5119, 5157, 5193, 5256, 5273, 5277, 5327, 5330,
5338, 5380, 5412, 5445, 5451, 5529, 5563, 5678, 5698, 5704, 5745, 5753, 5761, 5768,
5781, 5786, 5788, 5789, 5792, 5798, 5810, 5827, 5842, 5855, 5886, 5907, 5963, 5973,
6040, 6085, 6116, 6144, 6150, 6154, 6160, 6167, 6174, 6250, 6263, 6269, 6277, 6307,
6310, 6349, 6368, 6380, 6384, 6391, 6393, 6404, 6429, 6437, 6453, 6456, 6469, 6491,
6496, 6514, 6519, 6552, 6588, 6595, 6603, 6617, 6644, 6699, 6716, 6727, 6836, 6890,
7284, 7318, 7708, 7790
319-115
ON A/C 3231, 3292
319-131
ON A/C 3248, 3252, 3276, 3317, 3421, 3424, 3428, 3454, 3463, 3491, 3520, 3548, 3561,
3578, 3580, 3588, 3590, 3595, 3614, 3638, 3663, 3671, 3685, 3694, 3710, 3757, 3759,
3768, 3770, 3772, 3779, 3801, 3803, 3832, 3839, 3841, 3842, 3860, 3890, 3911, 3914,
3958, 3982, 4000, 4036, 4163, 4166, 4171, 4192, 4227, 4256, 4282, 4285, 4301, 4389,
4403, 4422, 4563, 4598, 4605, 4629, 4665, 4695, 4755, 4773, 4774, 4790, 4998, 5043,
5219, 5280, 5345, 5406, 5457, 5467, 5535, 5569, 5826, 5920, 5941, 5944, 5978, 6052,
6068, 6099, 6132, 6191, 6298, 6593
319-132
ON A/C 3114, 3116, 3124, 3175, 3253, 3279, 3450, 3680, 3705, 3836, 3849, 3851, 3876,
3897, 3901, 3962, 4018, 4042, 4060, 4114, 4151, 4215, 4259, 4262, 4319, 4410, 4428,
4452, 4522, 4529, 4583, 4660, 4842, 4992, 4995, 5105, 5208, 5261, 5267, 5286, 5376,
5389, 5439, 5609, 5623, 5650, 5700, 5765, 5868, 5910, 5953, 7711, 7738, 7814, 7827
319-133
ON A/C 3083, 3087, 3095, 3101, 3107, 3123, 3131, 3132, 3135, 3149, 3152, 3153, 3155,
3157, 3160, 3170, 3180, 3187, 3197, 3205, 3206, 3211, 3215, 3218, 3221, 3224, 3230,
3234, 3236, 3240, 3246, 3256, 3266, 3268, 3272, 3273, 3278, 3282, 3284, 3286, 3293,
3304, 3306, 3310, 3312, 3313, 3321, 3323, 3337, 3349, 3359, 3361, 3366, 3368, 3373,
3374, 3383, 3389, 3391, 3396, 3398, 3408, 3410, 3420, 3422, 3425, 3431, 3433, 3435,
3440, 3444, 3446, 3455, 3456, 3460, 3461, 3465, 3470, 3472, 3473, 3475, 3476, 3480,
3485, 3487, 3490, 3492, 3494, 3501, 3503, 3506, 3508, 3511, 3514, 3516, 3528, 3529,
3540, 3545, 3553, 3559, 3565, 3574, 3579, 3594, 3596, 3597, 3599, 3601, 3605, 3611,
3616, 3626, 3627, 3630, 3631, 3640, 3644, 3646, 3652, 3656, 3658, 3662, 3664, 3667,
3670, 3690, 3696, 3698, 3699, 3706, 3711, 3723, 3731, 3739, 3747, 3750, 3755, 3756,
3758, 3762, 3767, 3769, 3777, 3778, 3780, 3781, 3786, 3787, 3789, 3791, 3795, 3798,
3802, 3805, 3809, 3817, 3819, 3823, 3825, 3827, 3831, 3833, 3835, 3840, 3843, 3848,
3852, 3855, 3857, 3859, 3861, 3866, 3868, 3871, 3880, 3883, 3887, 3889, 3891, 3894,
3896, 3898, 3900, 3907-3909, 3913, 3915, 3919, 3922, 3923, 3925, 3931, 3933, 3939, 3945,
3946, 3949, 3953, 3954, 3961, 3967, 3971, 3972, 3974, 3975, 3979, 3980, 3984, 3988,
3991, 3992, 3995, 4001, 4006, 4010-4015, 4021, 4026, 4028, 4030, 4032-4034, 4046, 4049,
4051, 4055, 4057, 4059, 4061, 4063, 4064, 4072, 4079, 4081, 4083, 4084, 4086, 4090,
4092, 4093, 4095, 4097, 4100-4102, 4104-4106, 4115, 4117, 4120, 4122, 4128, 4133, 4135,
4137, 4139, 4145, 4146, 4149, 4150, 4153, 4154, 4157-4162, 4167, 4168, 4172, 4175, 4179,
4187, 4188, 4190, 4191, 4193, 4196, 4199, 4201-4203, 4205, 4207, 4208, 4212, 4218, 4219,
4226, 4231, 4233-4237, 4241-4244, 4250, 4253, 4255, 4261, 4263, 4267, 4269, 4272, 4273,
4276, 4281, 4284, 4286, 4289, 4291, 4293-4295, 4298, 4304, 4307, 4310, 4314, 4316, 4320,
4322, 4324, 4325, 4329, 4331, 4335, 4337, 4344, 4345, 4347, 4349, 4357, 4362-4366, 4368,
4371, 4373, 4375, 4376, 4379, 4381, 4391-4399, 4401, 4402, 4405, 4408, 4411, 4414, 4415,
4417, 4419, 4429, 4432, 4433, 4438, 4441, 4442, 4446-4449, 4453, 4454, 4456, 4463, 4465,
4468, 4475, 4478, 4480, 4484, 4485, 4487, 4489, 4490, 4492, 4498, 4499, 4501, 4502,
4504, 4507, 4508, 4510, 4512, 4517, 4519, 4521, 4524, 4526, 4528, 4537, 4539, 4541,
4544, 4547, 4550, 4554-4556, 4558, 4559, 4562, 4564, 4565, 4567, 4568, 4572-4574, 4579,
4581, 4586-4589, 4591, 4594, 4596, 4599-4601, 4604, 4606, 4610, 4613, 4616, 4618, 4623,
4625, 4627, 4631, 4634, 4636, 4639, 4641, 4646, 4649, 4651, 4652, 4655, 4656, 4658,
4659, 4661, 4664, 4668, 4671, 4673-4676, 4678, 4680, 4681, 4684, 4685, 4688, 4689, 4692,
4694, 4699, 4702, 4704, 4708, 4709, 4711, 4712, 4714, 4715, 4718, 4720-4724, 4727, 4729,
4730, 4733, 4735, 4738, 4740, 4742, 4743, 4745, 4747-4750, 4758, 4760, 4763, 4765, 4767,
4769, 4770, 4776, 4777, 4780, 4789, 4794, 4795, 4799, 4800, 4803, 4805, 4806, 4808,
4809, 4814-4816, 4820, 4821, 4823, 4827, 4829, 4831, 4833, 4835, 4839, 4840, 4844, 4848,
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 13
A318/A319/A320/A321
SERVICE BULLETIN
4849, 4851, 4852, 4854, 4855, 4857, 4860-4862, 4865, 4867, 4869, 4870, 4876, 4877, 4880,
4886, 4887, 4890-4892, 4894-4896, 4900, 4903, 4907-4909, 4913, 4915, 4917, 4921, 4924,
4927, 4928, 4933, 4936-4939, 4941-4943, 4946, 4948, 4952, 4953, 4955, 4958, 4959, 4963,
4964, 4967, 4970, 4972, 4974, 4978, 4981, 4983-4985, 4987, 4988, 4991, 4993, 4999, 5001,
5003, 5004, 5006-5008, 5012-5017, 5019, 5020, 5022, 5026, 5031-5034, 5037, 5045-5048,
5051, 5052, 5056, 5058, 5063, 5064, 5066, 5067, 5069-5072, 5081, 5082, 5084, 5086, 5096,
5100-5104, 5106-5117, 5122, 5125, 5129, 5131, 5134, 5136, 5138, 5140, 5143, 5146, 5147,
5150, 5152, 5153, 5162, 5163, 5165-5167, 5171, 5172, 5174, 5175, 5178, 5179, 5181, 5184,
5187, 5189, 5191, 5195, 5200, 5201, 5203, 5204, 5206, 5209, 5213, 5216, 5220-5224, 5226,
5229, 5232, 5234, 5236, 5238, 5240, 5243, 5246, 5249, 5250, 5252, 5253, 5260, 5263,
5264, 5266, 5276, 5278, 5289, 5290, 5299, 5304, 5307, 5310, 5315, 5316, 5318-5320, 5324,
5325, 5329, 5331, 5333, 5339, 5341, 5342, 5344, 5351, 5356, 5358, 5360, 5364, 5369,
5371-5373, 5378, 5379, 5381, 5384, 5386, 5393, 5394, 5396, 5398, 5399, 5403, 5405, 5408,
5414-5416, 5419, 5421, 5423, 5425, 5434, 5440-5443, 5446, 5448, 5452-5455, 5463, 5464,
5466, 5471, 5474, 5477, 5483, 5487, 5491, 5493, 5494, 5497, 5498, 5502, 5511, 5512,
5514, 5515, 5518, 5521, 5522, 5525-5527, 5533, 5536, 5540-5542, 5544, 5548, 5550-5552,
5554, 5556, 5557, 5559, 5560, 5562, 5565, 5568, 5571, 5572, 5574, 5576, 5578, 5580,
5581, 5583, 5585-5587, 5589, 5591, 5592, 5597, 5601, 5607, 5610, 5614, 5616, 5621, 5622,
5625, 5626, 5630, 5632, 5635, 5638-5640, 5642, 5643, 5648, 5652-5654, 5656, 5658, 5661,
5664-5666, 5668, 5669, 5673, 5675, 5679, 5686-5688, 5690, 5691, 5693, 5694, 5702, 5707,
5710, 5716, 5718, 5719, 5722, 5724, 5726, 5730, 5731, 5735, 5737, 5739-5742, 5746, 5748,
5749, 5752, 5754, 5757, 5759, 5760, 5764, 5766, 5769, 5771-5773, 5777, 5778, 5785, 5799,
5801, 5802, 5809, 5811, 5816, 5818, 5822, 5830, 5831, 5833, 5841, 5844, 5845, 5848,
5859, 5862, 5867, 5869, 5873, 5874, 5878, 5879, 5883, 5889, 5891, 5901-5903, 5911, 5912,
5917, 5921, 5925-5927, 5929, 5931, 5933-5935, 5943, 5945, 5950, 5957, 5965, 5967, 5970,
5972, 5974, 5976, 5981, 5982, 5984, 5989, 5990, 5995, 5997, 6000, 6003, 6004, 6006,
6011, 6012, 6017, 6021, 6022, 6025, 6026, 6033, 6039, 6041, 6043-6045, 6047, 6048, 6050,
6051, 6054, 6055, 6057, 6060, 6061, 6064-6066, 6069, 6071-6073, 6075, 6079-6081, 6084,
6090, 6092, 6095, 6096, 6102, 6103, 6105, 6107, 6110-6112, 6117, 6118, 6124, 6125, 6127,
6135, 6139, 6141, 6149, 6151, 6153, 6157, 6158, 6164, 6166, 6169, 6171, 6173, 6176,
6177, 6183, 6184, 6188, 6192, 6202, 6204, 6206, 6207, 6209, 6213, 6215, 6216, 6218,
6220, 6224, 6225, 6231, 6234, 6239, 6242-6244, 6246, 6248, 6251, 6257-6260, 6262, 6265,
6267, 6270, 6274, 6280-6283, 6285, 6292, 6293, 6301, 6309, 6315, 6317, 6318, 6320, 6322,
6323, 6325, 6328, 6329, 6333, 6335, 6338, 6339, 6341, 6347, 6348, 6350, 6353, 6355-6358,
6361, 6365, 6367, 6369, 6372, 6373, 6375, 6378, 6379, 6386, 6392, 6397, 6403, 6408,
6410-6413, 6416, 6418, 6422, 6423, 6430, 6434, 6441, 6442, 6444, 6446, 6447, 6452, 6457,
6458, 6465-6467, 6476, 6481, 6485, 6492, 6494, 6497, 6498, 6500, 6502, 6503, 6505, 6509,
6516, 6521, 6524, 6525, 6528, 6529, 6536, 6538, 6540-6542, 6546, 6547, 6549, 6550, 6553,
6561, 6562, 6564, 6565, 6568, 6570, 6572, 6577, 6582, 6584, 6587, 6591, 6596-6598, 6600,
6605, 6606, 6608, 6619, 6622, 6626, 6628, 6633, 6634, 6636, 6637, 6640, 6646, 6648,
6651, 6654, 6661, 6664-6666, 6669, 6671, 6674, 6675, 6677, 6679-6681, 6686, 6689, 6690,
6692, 6695, 6697, 6704, 6708, 6710, 6712-6715, 6717, 6721, 6722, 6724, 6728, 6730, 6732,
6737-6739, 6741-6743, 6746, 6753, 6754, 6759, 6764, 6765, 6769, 6773, 6776, 6777, 6779,
6782, 6784, 6786-6789, 6800, 6803, 6805-6808, 6811, 6813, 6815, 6823, 6824, 6826, 6830,
6831, 6834, 6835, 6837, 6838, 6843, 6846, 6847, 6856, 6858, 6862, 6870, 6871, 6874,
6876-6878, 6881, 6885, 6889, 6892, 6893, 6896, 6902, 6911, 6918, 6922, 6924, 6925, 6927,
6929, 6931, 6937, 6939, 6941, 6942, 6944, 6947, 6950, 6951, 6953, 6954, 6958, 6959,
6962-6966, 6970, 6974, 6977, 6980-6982, 6985, 6986, 6991-6993, 6995-6997, 7002, 7004,
7012, 7016, 7019, 7022, 7024, 7025, 7027, 7035, 7038-7040, 7044, 7049, 7050, 7056, 7059,
7063, 7066-7068, 7070, 7071, 7077, 7080, 7082, 7087, 7091-7093, 7095, 7096, 7099, 7104,
7111, 7113, 7115, 7116, 7120-7122, 7132, 7138, 7145, 7148, 7151, 7158-7160, 7167-7170,
7174, 7177, 7178, 7183, 7189, 7200, 7201, 7207, 7210, 7211, 7215, 7216, 7219, 7221,
7223-7226, 7228, 7231, 7235, 7238, 7240, 7243, 7245, 7251, 7253, 7256, 7258, 7259, 7261,
7263, 7264, 7272, 7275, 7279, 7282, 7289, 7292, 7295, 7297, 7302, 7308, 7312, 7314,
7315, 7319, 7325, 7328, 7337, 7338, 7340, 7345, 7350, 7355, 7361, 7365, 7370, 7372,
7374, 7377, 7383, 7385, 7389, 7392-7394, 7397, 7398, 7404-7406, 7408, 7410-7412, 7414,
7421, 7425, 7426, 7431, 7432, 7437, 7439, 7444, 7447, 7450, 7452, 7453, 7456, 7458,
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 14
A318/A319/A320/A321
SERVICE BULLETIN
7460, 7463-7465, 7467, 7469, 7473, 7474, 7476, 7482, 7485, 7487, 7490, 7496, 7503, 7513,
7527, 7531, 7534, 7537, 7542, 7543, 7545, 7549, 7550, 7556, 7561, 7569, 7572, 7574,
7580, 7582, 7593, 7597, 7604, 7605, 7608, 7609, 7614, 7615, 7619, 7620, 7622, 7625,
7630, 7632, 7633, 7637, 7640, 7643, 7644, 7646, 7653, 7654, 7657, 7659, 7660, 7664-7666,
7669, 7670, 7673, 7681, 7683, 7685, 7687, 7693, 7696, 7699, 7701, 7704, 7712, 7713,
7716, 7718, 7728, 7730, 7740, 7742, 7743, 7745, 7747, 7748, 7750, 7762, 7766, 7767,
7772, 7773, 7779-7781, 7784, 7785, 7789, 7792, 7797, 7805, 7806, 7816, 7817, 7819, 7823,
7829, 7832, 7836, 7838, 7843, 7846, 7905
320-214
ON A/C 3140, 3154, 3173, 3178, 3182, 3194, 3201, 3213, 3223, 3232, 3261, 3277, 3291,
3295, 3299, 3325, 3327, 3328, 3338, 3343, 3353, 3362, 3370, 3394, 3404, 3412, 3427,
3448, 3464, 3477, 3482, 3486, 3489, 3502, 3505, 3515, 3521, 3532, 3536, 3549, 3563,
3568, 3576, 3582, 3598, 3609, 3610, 3628, 3643, 3666, 3679, 3695, 3701, 3715, 3729,
3732, 3765, 3776, 3813, 3815, 3846, 3875, 3885, 3906, 3921, 3956, 3963, 3976, 3978,
3997, 4019, 4035, 4070, 4075, 4088, 4098, 4108, 4119, 4126, 4143, 4147, 4152, 4195,
4249, 4278, 4302, 4333, 4346, 4361, 4367, 4386, 4390, 4404, 4426, 4458, 4462, 4477,
4486, 4520, 4523, 4536, 4557, 4571, 4582, 4793, 4797, 4807, 4882, 4889, 4969, 4979,
4980, 4989, 5098, 5137, 5149, 5215, 5272, 5283, 5347, 5353, 5359, 5397, 5420, 5428,
5430, 5431, 5468, 5486, 5501, 5505, 5547, 5570, 5590, 5593, 5619, 5627, 5657, 5692,
5703, 5706, 5729, 5762, 5812, 5815, 5824, 5839, 5846, 5851, 5863, 5866, 5887, 5888,
5897, 5905, 5906, 5908, 5914, 5918, 5959, 6015, 6034, 6088, 6145, 6170, 6178, 6240,
6405, 6428, 6676, 6702, 6972, 7030, 7057, 7136, 7164, 7583, 7624
320-216
ON A/C 3089, 3105, 3125, 3127, 3143, 3156, 3158, 3159, 3166, 3167, 3177, 3185, 3192,
3196, 3208, 3210, 3219, 3227, 3239, 3257, 3259, 3264, 3270, 3275, 3296, 3301, 3303,
3308, 3314, 3316, 3330, 3332, 3335, 3341, 3351, 3354, 3357, 3365, 3379, 3381, 3384,
3386, 3392, 3402, 3409, 3414, 3416, 3423, 3430, 3437, 3439, 3449, 3451, 3453, 3457,
3468, 3474, 3478, 3479, 3481, 3483, 3484, 3488, 3495-3497, 3499, 3517, 3519, 3526, 3531,
3541, 3547, 3550, 3554, 3558, 3562, 3567, 3572, 3577, 3581, 3591, 3603, 3607, 3613,
3618, 3621, 3622, 3641, 3649, 3650, 3654, 3659, 3668, 3672, 3674, 3676, 3677, 3692,
3693, 3697, 3703, 3707, 3709, 3713, 3714, 3716, 3718, 3719, 3721, 3724, 3726, 3734,
3736, 3741, 3743, 3745, 3748, 3753, 3760, 3771, 3773, 3775, 3782, 3783, 3785, 3793,
3797, 3800, 3804, 3807, 3811, 3812, 3829, 3837, 3850, 3863, 3870, 3873, 3877, 3902,
3904, 3910, 3912, 3917, 3927, 3929, 3935, 3937, 3941, 3943, 3947, 3959, 3965, 3968,
3986, 3990, 3999, 4003, 4008, 4017, 4023, 4027, 4037, 4043, 4053, 4065, 4066, 4068,
4077, 4094, 4109-4111, 4113, 4124, 4130, 4140, 4144, 4156, 4165, 4170, 4174, 4176-4178,
4181, 4183, 4185, 4186, 4197, 4206, 4210, 4214, 4216, 4220, 4223, 4225, 4229, 4232,
4238-4240, 4245-4248, 4252, 4257, 4260, 4264, 4265, 4270, 4279, 4288, 4290, 4296, 4297,
4300, 4303, 4305, 4306, 4308, 4309, 4312, 4317, 4321, 4323, 4326, 4328, 4339, 4340,
4342, 4343, 4348, 4350, 4351, 4354-4356, 4359, 4370, 4372, 4378, 4384, 4388, 4407, 4409,
4412, 4413, 4421, 4423, 4424, 4431, 4434-4436, 4440, 4443, 4445, 4459, 4460, 4464, 4466,
4469, 4471, 4473, 4474, 4479, 4481-4483, 4488, 4491, 4493, 4495-4497, 4505, 4506, 4509,
4513-4516, 4518, 4525, 4527, 4531-4533, 4535, 4540, 4546, 4548, 4549, 4551-4553, 4561,
4566, 4569, 4575, 4576, 4578, 4580, 4584, 4592, 4593, 4595, 4597, 4602, 4603, 4608,
4609, 4612, 4614, 4615, 4619-4621, 4628, 4630, 4632, 4633, 4637, 4642, 4644, 4645,
4647, 4657, 4666, 4670, 4677, 4683, 4686, 4687, 4696, 4697, 4700, 4707, 4716, 4725,
4726, 4736, 4739, 4751, 4752, 4754, 4757, 4762, 4772, 4775, 4782, 4784, 4786, 4791,
4802, 4804, 4810, 4812, 4813, 4817, 4818, 4825, 4836, 4845, 4853, 4858, 4864, 4866,
4868, 4872, 4874, 4879, 4883, 4884, 4888, 4897, 4899, 4902, 4904, 4905, 4911, 4912,
4914, 4918-4920, 4922, 4926, 4929-4931, 4934, 4947, 4951, 4954, 4961, 4965, 4968, 4973,
4975, 4977, 4982, 4986, 4990, 4996, 4997, 5000, 5002, 5010, 5011, 5021, 5024, 5027,
5029, 5030, 5036, 5039, 5041, 5042, 5053, 5055, 5060, 5061, 5073, 5075, 5076, 5078,
5080, 5090-5095, 5120, 5121, 5123, 5127, 5128, 5132, 5135, 5139, 5141, 5142, 5144, 5145,
5148, 5151, 5155, 5156, 5158, 5159, 5161, 5168, 5170, 5176, 5182, 5183, 5185, 5188,
5190, 5194, 5196, 5198, 5202, 5211, 5214, 5217, 5218, 5225, 5228, 5230, 5231, 5242,
5245, 5248, 5255, 5258, 5259, 5262, 5268, 5270, 5274, 5281, 5288, 5291, 5298, 5301,
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 15
A318/A319/A320/A321
SERVICE BULLETIN
5302, 5305, 5311-5313, 5323, 5326, 5334, 5335, 5348, 5349, 5352, 5355, 5361-5363, 5365,
5367, 5370, 5375, 5387, 5390, 5395, 5401, 5407, 5410, 5411, 5417, 5426, 5429, 5433,
5436, 5437, 5449, 5458, 5460, 5461, 5472, 5473, 5476, 5479, 5480, 5482, 5484, 5489,
5492, 5496, 5499, 5503, 5506-5508, 5516, 5517, 5520, 5524, 5530, 5532, 5537, 5539, 5553,
5561, 5564, 5566, 5577, 5579, 5596, 5598-5600, 5602, 5604, 5605, 5608, 5611-5613, 5615,
5617, 5618, 5620, 5624, 5628, 5629, 5631, 5634, 5637, 5641, 5645, 5646, 5649, 5660,
5662, 5671, 5672, 5676, 5677, 5680, 5682, 5683, 5685, 5695, 5697, 5701, 5708, 5711-5714,
5717, 5721, 5723, 5725, 5727, 5732, 5734, 5738, 5744, 5750, 5756, 5775, 5780, 5782,
5784, 5791, 5796, 5797, 5804-5807, 5813, 5814, 5817, 5821, 5823, 5828, 5829, 5832, 5835,
5837, 5847, 5850, 5852, 5853, 5856-5858, 5861, 5864, 5870, 5871, 5875, 5877, 5880, 5882,
5885, 5892-5894, 5896, 5898, 5900, 5915, 5923, 5924, 5928, 5930, 5937, 5940, 5942, 5948,
5951, 5952, 5954, 5956, 5962, 5964, 5968, 5971, 5977, 5979, 5985, 5986, 5992, 5993,
5999, 6001, 6007, 6008, 6010, 6018, 6019, 6023, 6028-6030, 6032, 6036, 6037, 6058, 6062,
6076-6078, 6082, 6086, 6091, 6093, 6098, 6106, 6113, 6115, 6120, 6123, 6128, 6129, 6131,
6134, 6136, 6137, 6140, 6142, 6147, 6155, 6180, 6182, 6187, 6189, 6193, 6195, 6197,
6198, 6200, 6208, 6212, 6217, 6223, 6226, 6228, 6229, 6235, 6237, 6247, 6254, 6275,
6278, 6284, 6287, 6289, 6290, 6296, 6297, 6300, 6302, 6304, 6306, 6311, 6327, 6331,
6336, 6340, 6343, 6345, 6352, 6360, 6362, 6370, 6374, 6377, 6381, 6383, 6388, 6394,
6400, 6402, 6417, 6421, 6424, 6426, 6431, 6436, 6439, 6449, 6450, 6455, 6460, 6462,
6463, 6471, 6474, 6478, 6480, 6483, 6486, 6487, 6489, 6506, 6507, 6510, 6513, 6518,
6522, 6527, 6530, 6533, 6535, 6544, 6551, 6557, 6559, 6566, 6571, 6574, 6576, 6578,
6580, 6583, 6586, 6589, 6594, 6602, 6604, 6607, 6611, 6612, 6614, 6616, 6624, 6631,
6635, 6643, 6645, 6655, 6659, 6662, 6668, 6683, 6688, 6694, 6700, 6706, 6733, 6735,
6749, 6750, 6752, 6755, 6771, 6775, 6785, 6792, 6794, 6795, 6816, 6820, 6832, 6841,
6851, 6854, 6857, 6865, 6875, 6882, 6883, 6886, 6888, 6898, 6900, 6901, 6917, 6919,
6921, 6932, 6934, 6943, 6955, 6961, 6971, 6978, 6984, 6989, 7006, 7008, 7014, 7017,
7020, 7026, 7028, 7041, 7043, 7062, 7075, 7086, 7100, 7109, 7110, 7134, 7153, 7156,
7163, 7190, 7197, 7203, 7213, 7232, 7234, 7247, 7262, 7267, 7270, 7347, 7351, 7356,
7362, 7378, 7402, 7420, 7423, 7434, 7435, 7442, 7491, 7497, 7502, 7585, 7595, 7635,
7656, 7679, 7691, 7695, 7717, 7724, 7725, 7760, 7761, 7771, 7796, 7808, 7809, 7909
320-232
ON A/C 3280, 3319, 3378, 3418, 3510, 3524, 3535, 3538, 3543, 3556, 3570, 3624, 4118,
4383, 4400, 4439, 4457, 4476, 4543, 4653, 4690, 4701, 4741, 4798, 4828, 4832, 4906,
4944, 4950, 5050, 5062, 5068, 5089, 5207, 5212, 5296, 5308, 5322, 5337, 5391, 5488,
5510, 5531, 5595, 5651, 5776, 5793, 5794, 5819, 5840, 5988, 5996, 6014, 6109, 6161,
6288, 6321, 6332, 6445, 6470, 6555, 6610, 6705, 6778, 6906, 6948, 6969, 7000, 7088,
7118, 7123, 7376, 7457
320-233
ON A/C 0970, 0995, 3130, 3146, 3191, 3212, 3233, 3247, 3249, 3262, 3267, 3326, 3334,
3340, 3367, 3401, 3471, 3498, 3504, 3557, 3573, 3584, 3593, 3612, 3619, 3629, 3633,
3639, 3682, 3708, 3749, 3752, 3792, 3830, 3879, 3884, 3928, 3955, 4002, 4009, 4058,
4074, 4078, 4096, 4099, 4103, 4116, 4138, 4148, 4155, 4194, 4274, 4280, 4334, 4338,
4369, 4416, 4461, 4467, 4500, 4542, 4577, 4590, 4611, 4648, 4728, 4811, 4838, 4925,
4962, 5009, 5038, 5044, 5059, 5065, 5126, 5133, 5271, 5285, 5295, 5314, 5328, 5354,
5377, 5444, 5447, 5475, 5485, 5504, 5509, 5513, 5538, 5549, 5588, 5594, 5603, 5644,
5659, 5674, 5681, 5684, 5696, 5720, 5733, 5755, 5779, 5790, 5808, 5843, 5849, 5872,
5876, 5881, 5913, 5919, 5966, 5969, 6005, 6016, 6024, 6038, 6042, 6053, 6056, 6067,
6087, 6114, 6119, 6122, 6156, 6168, 6172, 6179, 6210, 6221, 6232, 6268, 6276, 6312,
6314, 6342, 6351, 6364, 6376, 6389, 6398, 6406, 6409, 6414, 6432, 6433, 6435, 6438,
6454, 6459, 6468, 6477, 6484, 6488, 6501, 6511, 6515, 6526, 6545, 6548, 6585, 6590,
6592, 6615, 6627, 6629, 6632, 6639, 6653, 6658, 6670, 6678, 6685, 6696, 6698, 6701,
6707, 6718, 6719, 6726, 6729, 6747, 6756, 6762, 6767, 6780, 6793, 6797, 6798, 6814,
6817, 6825, 6844, 6845, 6852, 6855, 6872, 6873, 6884, 6891, 6894, 6895, 6899, 6905,
6926, 6935, 6936, 6945, 6949, 6957, 6960, 6968, 6979, 6999, 7003, 7005, 7010, 7023,
7036, 7037, 7042, 7048, 7054, 7055, 7064, 7072, 7073, 7081, 7084, 7090, 7097, 7098,
7101, 7117, 7119, 7127, 7128, 7130, 7137, 7142, 7143, 7171, 7176, 7179, 7184, 7187,
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 16
A318/A319/A320/A321
SERVICE BULLETIN
7193, 7194, 7198, 7202, 7204, 7212, 7222, 7227, 7237, 7239, 7241, 7244, 7250, 7254,
7255, 7260, 7265, 7271, 7276, 7278, 7286, 7287, 7294, 7298, 7300, 7306, 7311, 7313,
7317, 7320, 7332, 7339, 7342, 7344, 7346, 7348, 7358, 7360, 7366, 7369, 7371, 7379,
7382, 7400, 7413, 7418, 7424, 7427, 7430, 7433, 7446, 7454, 7461, 7478, 7481, 7493,
7498, 7506, 7524, 7536, 7551, 7558, 7573, 7575, 7586, 7601, 7628, 7641, 7645, 7650,
7652, 7655, 7658, 7667, 7675, 7678, 7680, 7684, 7689, 7715, 7720, 7726, 7736, 7749,
7758, 7759, 7769, 7782, 7787, 7793, 7801, 7810, 7818, 7830, 7833
321-211
ON A/C 3372, 3399, 3419, 3441, 3814, 3930, 4251, 4534, 4901, 5567, 7007
321-212
ON A/C 3307, 3329, 3523, 3623, 3653, 3655, 3665, 3678, 3722, 3725, 3766, 3806, 3940,
3973, 4022, 4031, 4062, 4091, 4131, 4180, 4221, 4283, 4318, 4377, 4472, 4494, 4538,
5435, 5573, 5743, 6013, 6196, 6319, 6567, 6579, 6641
321-213
ON A/C 1928, 2107, 3106, 3207, 3217, 3222, 3229, 3235, 3241, 3251, 3254, 3265, 3274,
3283, 3290, 3294, 3297, 3302, 3315, 3322, 3339, 3350, 3355, 3360, 3369, 3382, 3387,
3397, 3405, 3429, 3434, 3458, 3459, 3462, 3493, 3507, 3512, 3522, 3525, 3527, 3539,
3546, 3552, 3566, 3575, 3583, 3587, 3592, 3600, 3625, 3636, 3637, 3645, 3669, 3673,
3681, 3688, 3712, 3717, 3730, 3737, 3738, 3740, 3761, 3764, 3784, 3796, 3816, 3820,
3847, 3858, 3862, 3864, 3867, 3869, 3878, 3881, 3893, 3899, 3916, 3920, 3924, 3926,
3934, 3936, 3938, 3944, 3948, 3951, 3960, 3964, 3966, 3969, 3977, 3981, 3987, 3989,
3993, 3996, 4005, 4016, 4025, 4041, 4044, 4045, 4047, 4050, 4054, 4067, 4073, 4082,
4085, 4107, 4112, 4123, 4134, 4136, 4142, 4173, 4184, 4189, 4198, 4209, 4213, 4217,
4224, 4230, 4266, 4271, 4277, 4292, 4299, 4311, 4315, 4341, 4352, 4358, 4360, 4374,
4382, 4387, 4406, 4420, 4430, 4530, 4545, 4560, 4570, 4585, 4607, 4626, 4638, 4643,
4654, 4662, 4669, 4672, 4682, 4698, 4703, 4706, 4710, 4731, 4737, 4746, 4753, 4761,
4779, 4783, 4788, 4792, 4819, 4824, 4826, 4830, 4843, 4847, 4850, 4856, 4863, 4881,
4885, 4893, 4898, 4916, 4923, 4932, 4935, 4940, 4945, 4957, 4960, 4966, 4971, 4976,
4994, 5025, 5028, 5035, 5049, 5074, 5077, 5083, 5087, 5099, 5118, 5154, 5160, 5164,
5169, 5173, 5177, 5180, 5186, 5192, 5197, 5205, 5210, 5227, 5233, 5235, 5237, 5241,
5244, 5247, 5251, 5254, 5257, 5269, 5275, 5279, 5282, 5287, 5292, 5297, 5300, 5303,
5306, 5309, 5317, 5321, 5332, 5336, 5340, 5343, 5350, 5357, 5368, 5374, 5382, 5385,
5388, 5392, 5402, 5404, 5409, 5413, 5418, 5422, 5427, 5438, 5450, 5456, 5459, 5462,
5465, 5469, 5470, 5481, 5490, 5495, 5500, 5519, 5523, 5528, 5534, 5543, 5546, 5555,
5558, 5575, 5582, 5584, 5606, 5633, 5636, 5647, 5655, 5663, 5667, 5670, 5689, 5699,
5705, 5709, 5715, 5728, 5736, 5747, 5751, 5758, 5763, 5767, 5770, 5774, 5783, 5787,
5795, 5800, 5803, 5820, 5825, 5834, 5836, 5838, 5854, 5860, 5865, 5884, 5890, 5895,
5899, 5904, 5909, 5916, 5922, 5932, 5936, 5938, 5939, 5946, 5947, 5949, 5955, 5958,
5960, 5961, 5975, 5980, 5983, 5987, 5991, 5994, 5998, 6002, 6009, 6020, 6027, 6031,
6035, 6046, 6049, 6059, 6063, 6070, 6074, 6083, 6089, 6094, 6097, 6100, 6104, 6108,
6121, 6126, 6130, 6133, 6138, 6143, 6146, 6148, 6152, 6162, 6163, 6165, 6175, 6181,
6185, 6186, 6190, 6194, 6199, 6201, 6203, 6205, 6211, 6214, 6219, 6222, 6227, 6230,
6233, 6236, 6238, 6241, 6245, 6249, 6252, 6253, 6255, 6256, 6261, 6264, 6266, 6271,
6272, 6279, 6291, 6294, 6295, 6299, 6303, 6305, 6313, 6316, 6324, 6326, 6330, 6334,
6337, 6344, 6346, 6359, 6363, 6366, 6371, 6382, 6385, 6387, 6390, 6395, 6396, 6399,
6401, 6407, 6415, 6420, 6425, 6427, 6440, 6443, 6448, 6451, 6461, 6472, 6473, 6475,
6479, 6482, 6490, 6493, 6495, 6499, 6504, 6508, 6512, 6517, 6520, 6523, 6531, 6532,
6534, 6537, 6539, 6543, 6554, 6556, 6558, 6560, 6563, 6569, 6573, 6575, 6581, 6599,
6601, 6609, 6613, 6618, 6621, 6623, 6625, 6630, 6638, 6647, 6649, 6650, 6652, 6656,
6657, 6660, 6663, 6667, 6672, 6682, 6684, 6687, 6691, 6693, 6703, 6709, 6711, 6723,
6725, 6731, 6734, 6736, 6740, 6745, 6748, 6751, 6757, 6758, 6760, 6761, 6763, 6766,
6768, 6770, 6774, 6781, 6783, 6790, 6791, 6796, 6802, 6804, 6809, 6810, 6812, 6818,
6821, 6822, 6827, 6828, 6840, 6842, 6848, 6850, 6853, 6859, 6861, 6863, 6866, 6867,
6869, 6879, 6880, 6887, 6897, 6903, 6908-6910, 6912, 6913, 6915, 6916, 6928, 6930, 6933,
6938, 6940, 6956, 6973, 6976, 6983, 6987, 6988, 6990, 6994, 6998, 7009, 7013, 7015,
7018, 7021, 7029, 7032, 7034, 7045, 7046, 7052, 7058, 7065, 7069, 7076, 7079, 7085,
7089, 7105, 7106, 7108, 7114, 7125, 7131, 7133, 7135, 7139, 7144, 7146, 7152, 7154,
7155, 7157, 7166, 7173, 7180, 7182, 7188, 7191, 7196, 7199, 7206, 7208, 7217, 7218,
7220, 7229, 7230, 7242, 7246, 7257, 7266, 7274, 7280, 7285, 7288, 7296, 7299, 7301,
7303, 7305, 7307, 7310, 7316, 7322, 7326, 7335, 7336, 7349, 7353, 7357, 7363, 7368,
7375, 7384, 7388, 7390, 7395, 7403, 7407, 7415, 7416, 7419, 7422, 7438, 7440, 7443,
7445, 7448, 7451, 7455, 7462, 7471, 7488, 7492, 7500, 7509, 7515, 7516, 7518-7520, 7522,
7525, 7528, 7529, 7532, 7539, 7541, 7552, 7562, 7564, 7566, 7570, 7578, 7584, 7590,
7596, 7599, 7607, 7611, 7613, 7617, 7621, 7623, 7627, 7631, 7636, 7647, 7651, 7661,
7668, 7674, 7686, 7690, 7692, 7700, 7702, 7706, 7714, 7729, 7732, 7734, 7739, 7752,
7754, 7756, 7763, 7775, 7783, 7798, 7815, 7820, 7821, 7825, 7826, 7831, 7855, 7870
321-231
ON A/C 4617, 4719, 4771, 4834, 4873, 4949, 5054, 5124, 5199, 5265, 5346, 5432, 6159,
6273, 6308, 6354, 7161, 7248, 7324, 7468, 7511, 7557, 7722, 7741, 7774
321-232
CONF ALL
(2) Applicability by MSN
0970 0995 1928 2107 3019 3030 3062 3083 3087 3089 3095 3096 3101 3105-3107
3114 3116 3123-3125 3127 3130-3132 3135 3139 3140 3143 3146 3149 3152-3160
3166-3168 3170 3171 3173 3175 3177 3178 3180-3182 3185-3188 3191 3192 3194
3196 3197 3201 3202 3204-3208 3210-3219 3221-3224 3227 3229-3236 3239-3241
3245-3249 3251-3254 3256 3257 3259 3261 3262 3264-3268 3270-3286 3288
3290-3310 3312-3317 3319 3321-3332 3334-3341 3343 3344 3346 3347 3349-3351
3353-3355 3357 3359-3362 3364-3374 3377-3392 3394 3396-3399 3401-3437
3439-3499 3501-3512 3514-3529 3531-3533 3535-3541 3543-3616 3618-3631
3633-3647 3649-3750 3752-3820 3822-3825 3827-3855 3857-3881 3883-3885
3887-3931 3933-3951 3953-3984 3986-4168 4170-4210 4212-4329 4331-4449
4451-4502 4504-4649 4651-4731 4733-4877 4879-5477 5479-6100 6102-6285
6287-6418 6420-6463 6465-6619 6621-6641 6643-6672 6674-6719 6721-6743
6745-6771 6773-6798 6800 6802-6818 6820-6828 6830-6832 6834-6838 6840-6848
6850-6859 6861-6863 6865-6867 6869-6903 6905 6906 6908-6913 6915-6919 6921
6922 6924-6945 6947-6951 6953-6966 6968-6974 6976-7000 7002-7010 7012-7030
7032 7034-7046 7048-7050 7052 7054-7059 7062-7073 7075-7077 7079-7082
7084-7093 7095-7101 7104-7106 7108-7111 7113-7123 7125 7127 7128 7130-7139
7142-7146 7148 7151-7161 7163 7164 7166-7171 7173 7174 7176-7180 7182-7184
7187-7191 7193 7194 7196-7204 7206-7208 7210-7213 7215-7232 7234 7235
7237-7248 7250 7251 7253-7267 7270-7272 7274-7276 7278-7280 7282 7284-7289
7292 7294-7303 7305-7308 7310-7320 7322 7324-7326 7328 7332 7335-7340
7342 7344-7351 7353 7355-7358 7360-7363 7365 7366 7368-7372 7374-7379
7382-7385 7388-7390 7392-7395 7397 7398 7400 7402-7408 7410-7416 7418-7427
7430-7435 7437-7440 7442-7448 7450-7458 7460-7465 7467-7469 7471 7473 7474
7476 7478 7481 7482 7485 7487 7488 7490-7493 7496-7498 7500 7502 7503 7506
7509 7511 7513 7515 7516 7518-7520 7522 7524 7525 7527-7529 7531 7532 7534
7536 7537 7539 7541-7543 7545 7549-7552 7556-7558 7561 7562 7564 7566 7569
7570 7572-7575 7578 7580 7582-7586 7590 7593 7595-7597 7599 7601 7604 7605
7607-7609 7611 7613-7615 7617 7619-7625 7627 7628 7630-7633 7635-7637 7640
7641 7643-7647 7650-7661 7664-7670 7673-7675 7678-7681 7683-7687 7689-7693
7695 7696 7699-7702 7704 7706 7708 7711-7718 7720 7722 7724-7726 7728-7730
7732 7734 7736 7738-7743 7745 7747-7750 7752 7754 7756 7758-7763 7766 7767
7769 7771-7775 7779-7785 7787 7789 7790 7792 7793 7796-7798 7801 7805 7806
7808-7810 7814-7821 7823 7825-7827 7829-7833 7836 7838 7843 7846 7855 7870
7905 7909
(3) MSN by configuration
CONF 001
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 18
A318/A319/A320/A321
SERVICE BULLETIN
MSN CONFIGURATION
3030 3062 3214 3216 3371 3390 3469 3509 3585 3602 3606 001
3635 3642 4007 4039 5545
CONF 002
MSN CONFIGURATION
3019 3096 3114 3116 3124 3139 3168 3171 3175 3181 3186 002
3188 3202 3204 3231 3245 3248 3252 3253 3271 3276 3279
3281 3285 3288 3292 3298 3300 3305 3309 3317 3324 3331
3336 3344 3346 3347 3364 3377 3380 3385 3388 3403 3406
3407 3411 3413 3415 3417 3421 3424 3426 3428 3432 3436
3442 3443 3445 3447 3450 3452 3454 3463 3466 3467 3491
3518 3520 3533 3537 3544 3548 3551 3555 3560 3561 3564
3569 3571 3578 3580 3586 3588 3589 3590 3595 3604 3608
3614 3615 3620 3634 3638 3647 3651 3657 3660 3661 3663
3671 3675 3680 3683 3684 3685 3686 3687 3689 3691 3694
3700 3702 3704 3705 3710 3720 3727 3728 3733 3735 3742
3744 3746 3754 3757 3759 3763 3768 3770 3772 3774 3779
3788 3790 3794 3799 3801 3803 3808 3810 3818 3822 3824
3828 3832 3834 3836 3838 3839 3841 3842 3844 3845 3849
3851 3853 3854 3860 3865 3872 3874 3876 3888 3890 3892
3895 3897 3901 3903 3905 3911 3914 3918 3942 3950 3957
3958 3962 3970 3982 3983 3994 3998 4000 4004 4018 4020
4024 4029 4036 4038 4040 4042 4048 4052 4056 4060 4069
4071 4076 4080 4087 4089 4114 4121 4125 4127 4129 4132
4141 4151 4163 4164 4166 4171 4182 4192 4200 4204 4215
4222 4227 4228 4254 4256 4258 4259 4262 4268 4275 4282
4285 4287 4301 4313 4319 4327 4332 4336 4353 4380 4385
4389 4403 4410 4418 4422 4425 4427 4428 4437 4444 4451
4452 4455 4470 4511 4522 4529 4563 4583 4598 4605 4622
4624 4629 4635 4640 4660 4663 4665 4667 4679 4691 4693
4695 4705 4713 4717 4734 4744 4755 4756 4759 4764 4766
4768 4773 4774 4778 4781 4785 4787 4790 4796 4801 4822
4837 4841 4842 4846 4859 4871 4875 4910 4956 4992 4995
4998 5005 5018 5023 5040 5043 5057 5079 5085 5088 5097
5105 5119 5130 5157 5193 5208 5219 5239 5256 5261 5267
5273 5277 5280 5284 5286 5293 5294 5327 5330 5338 5345
5366 5376 5380 5383 5389 5400 5406 5412 5424 5439 5445
5451 5457 5467 5529 5535 5563 5569 5609 5623 5650 5678
5698 5700 5704 5745 5753 5761 5765 5768 5781 5786 5788
5789 5792 5798 5810 5826 5827 5842 5855 5868 5886 5907
5910 5920 5941 5944 5953 5963 5973 5978 6040 6052 6068
6085 6099 6116 6132 6144 6150 6154 6160 6167 6174 6191
6250 6263 6269 6277 6298 6307 6310 6349 6368 6380 6384
6391 6393 6404 6429 6437 6453 6456 6469 6491 6496 6514
6519 6552 6588 6593 6595 6603 6617 6644 6699 6716 6727
6836 6890 7284 7318 7708 7711 7738 7790 7814 7827
CONF 003
MSN CONFIGURATION
3083 3087 3089 3095 3101 3105 3107 3123 3125 3127 3131 003
3132 3135 3140 3143 3149 3152 3153 3154 3155 3156 3157
3158 3159 3160 3166 3167 3170 3173 3177 3178 3180 3182
3185 3187 3192 3194 3196 3197 3201 3205 3206 3208 3210
MSN CONFIGURATION
3211 3213 3215 3218 3219 3221 3223 3224 3227 3230 3232
3234 3236 3239 3240 3246 3256 3257 3259 3261 3264 3266
3268 3270 3272 3273 3275 3277 3278 3280 3282 3284 3286
3291 3293 3295 3296 3299 3301 3303 3304 3306 3308 3310
3312 3313 3314 3316 3319 3321 3323 3325 3327 3328 3330
3332 3335 3337 3338 3341 3343 3349 3351 3353 3354 3357
3359 3361 3362 3365 3366 3368 3370 3373 3374 3378 3379
3381 3383 3384 3386 3389 3391 3392 3394 3396 3398 3402
3404 3408 3409 3410 3412 3414 3416 3418 3420 3422 3423
3425 3427 3430 3431 3433 3435 3437 3439 3440 3444 3446
3448 3449 3451 3453 3455 3456 3457 3460 3461 3464 3465
3468 3470 3472 3473 3474 3475 3476 3477 3478 3479 3480
3481 3482 3483 3484 3485 3486 3487 3488 3489 3490 3492
3494 3495 3496 3497 3499 3501 3502 3503 3505 3506 3508
3510 3511 3514 3515 3516 3517 3519 3521 3524 3526 3528
3529 3531 3532 3535 3536 3538 3540 3541 3543 3545 3547
3549 3550 3553 3554 3556 3558 3559 3562 3563 3565 3567
3568 3570 3572 3574 3576 3577 3579 3581 3582 3591 3594
3596 3597 3598 3599 3601 3603 3605 3607 3609 3610 3611
3613 3616 3618 3621 3622 3624 3626 3627 3628 3630 3631
3640 3641 3643 3644 3646 3649 3650 3652 3654 3656 3658
3659 3662 3664 3666 3667 3668 3670 3672 3674 3676 3677
3679 3690 3692 3693 3695 3696 3697 3698 3699 3701 3703
3706 3707 3709 3711 3713 3714 3715 3716 3718 3719 3721
3723 3724 3726 3729 3731 3732 3734 3736 3739 3741 3743
3745 3747 3748 3750 3753 3755 3756 3758 3760 3762 3765
3767 3769 3771 3773 3775 3776 3777 3778 3780 3781 3782
3783 3785 3786 3787 3789 3791 3793 3795 3797 3798 3800
3802 3804 3805 3807 3809 3811 3812 3813 3815 3817 3819
3823 3825 3827 3829 3831 3833 3835 3837 3840 3843 3846
3848 3850 3852 3855 3857 3859 3861 3863 3866 3868 3870
3871 3873 3875 3877 3880 3883 3885 3887 3889 3891 3894
3896 3898 3900 3902 3904 3906 3907 3908 3909 3910 3912
3913 3915 3917 3919 3921 3922 3923 3925 3927 3929 3931
3933 3935 3937 3939 3941 3943 3945 3946 3947 3949 3953
3954 3956 3959 3961 3963 3965 3967 3968 3971 3972 3974
3975 3976 3978 3979 3980 3984 3986 3988 3990 3991 3992
3995 3997 3999 4001 4003 4006 4008 4010 4011 4012 4013
4014 4015 4017 4019 4021 4023 4026 4027 4028 4030 4032
4033 4034 4035 4037 4043 4046 4049 4051 4053 4055 4057
4059 4061 4063 4064 4065 4066 4068 4070 4072 4075 4077
4079 4081 4083 4084 4086 4088 4090 4092 4093 4094 4095
4097 4098 4100 4101 4102 4104 4105 4106 4108 4109 4110
4111 4113 4115 4117 4118 4119 4120 4122 4124 4126 4128
4130 4133 4135 4137 4139 4140 4143 4144 4145 4146 4147
4149 4150 4152 4153 4154 4156 4157 4158 4159 4160 4161
4162 4165 4167 4168 4170 4172 4174 4175 4176 4177 4178
4179 4181 4183 4185 4186 4187 4188 4190 4191 4193 4195
4196 4197 4199 4201 4202 4203 4205 4206 4207 4208 4210
4212 4214 4216 4218 4219 4220 4223 4225 4226 4229 4231
4232 4233 4234 4235 4236 4237 4238 4239 4240 4241 4242
4243 4244 4245 4246 4247 4248 4249 4250 4252 4253 4255
4257 4260 4261 4263 4264 4265 4267 4269 4270 4272 4273
4276 4278 4279 4281 4284 4286 4288 4289 4290 4291 4293
4294 4295 4296 4297 4298 4300 4302 4303 4304 4305 4306
MSN CONFIGURATION
4307 4308 4309 4310 4312 4314 4316 4317 4320 4321 4322
4323 4324 4325 4326 4328 4329 4331 4333 4335 4337 4339
4340 4342 4343 4344 4345 4346 4347 4348 4349 4350 4351
4354 4355 4356 4357 4359 4361 4362 4363 4364 4365 4366
4367 4368 4370 4371 4372 4373 4375 4376 4378 4379 4381
4383 4384 4386 4388 4390 4391 4392 4393 4394 4395 4396
4397 4398 4399 4400 4401 4402 4404 4405 4407 4408 4409
4411 4412 4413 4414 4415 4417 4419 4421 4423 4424 4426
4429 4431 4432 4433 4434 4435 4436 4438 4439 4440 4441
4442 4443 4445 4446 4447 4448 4449 4453 4454 4456 4457
4458 4459 4460 4462 4463 4464 4465 4466 4468 4469 4471
4473 4474 4475 4476 4477 4478 4479 4480 4481 4482 4483
4484 4485 4486 4487 4488 4489 4490 4491 4492 4493 4495
4496 4497 4498 4499 4501 4502 4504 4505 4506 4507 4508
4509 4510 4512 4513 4514 4515 4516 4517 4518 4519 4520
4521 4523 4524 4525 4526 4527 4528 4531 4532 4533 4535
4536 4537 4539 4540 4541 4543 4544 4546 4547 4548 4549
4550 4551 4552 4553 4554 4555 4556 4557 4558 4559 4561
4562 4564 4565 4566 4567 4568 4569 4571 4572 4573 4574
4575 4576 4578 4579 4580 4581 4582 4584 4586 4587 4588
4589 4591 4592 4593 4594 4595 4596 4597 4599 4600 4601
4602 4603 4604 4606 4608 4609 4610 4612 4613 4614 4615
4616 4618 4619 4620 4621 4623 4625 4627 4628 4630 4631
4632 4633 4634 4636 4637 4639 4641 4642 4644 4645 4646
4647 4649 4651 4652 4653 4655 4656 4657 4658 4659 4661
4664 4666 4668 4670 4671 4673 4674 4675 4676 4677 4678
4680 4681 4683 4684 4685 4686 4687 4688 4689 4690 4692
4694 4696 4697 4699 4700 4701 4702 4704 4707 4708 4709
4711 4712 4714 4715 4716 4718 4720 4721 4722 4723 4724
4725 4726 4727 4729 4730 4733 4735 4736 4738 4739 4740
4741 4742 4743 4745 4747 4748 4749 4750 4751 4752 4754
4757 4758 4760 4762 4763 4765 4767 4769 4770 4772 4775
4776 4777 4780 4782 4784 4786 4789 4791 4793 4794 4795
4797 4798 4799 4800 4802 4803 4804 4805 4806 4807 4808
4809 4810 4812 4813 4814 4815 4816 4817 4818 4820 4821
4823 4825 4827 4828 4829 4831 4832 4833 4835 4836 4839
4840 4844 4845 4848 4849 4851 4852 4853 4854 4855 4857
4858 4860 4861 4862 4864 4865 4866 4867 4868 4869 4870
4872 4874 4876 4877 4879 4880 4882 4883 4884 4886 4887
4888 4889 4890 4891 4892 4894 4895 4896 4897 4899 4900
4902 4903 4904 4905 4906 4907 4908 4909 4911 4912 4913
4914 4915 4917 4918 4919 4920 4921 4922 4924 4926 4927
4928 4929 4930 4931 4933 4934 4936 4937 4938 4939 4941
4942 4943 4944 4946 4947 4948 4950 4951 4952 4953 4954
4955 4958 4959 4961 4963 4964 4965 4967 4968 4969 4970
4972 4973 4974 4975 4977 4978 4979 4980 4981 4982 4983
4984 4985 4986 4987 4988 4989 4990 4991 4993 4996 4997
4999 5000 5001 5002 5003 5004 5006 5007 5008 5010 5011
5012 5013 5014 5015 5016 5017 5019 5020 5021 5022 5024
5026 5027 5029 5030 5031 5032 5033 5034 5036 5037 5039
5041 5042 5045 5046 5047 5048 5050 5051 5052 5053 5055
5056 5058 5060 5061 5062 5063 5064 5066 5067 5068 5069
5070 5071 5072 5073 5075 5076 5078 5080 5081 5082 5084
5086 5089 5090 5091 5092 5093 5094 5095 5096 5098 5100
5101 5102 5103 5104 5106 5107 5108 5109 5110 5111 5112
MSN CONFIGURATION
5113 5114 5115 5116 5117 5120 5121 5122 5123 5125 5127
5128 5129 5131 5132 5134 5135 5136 5137 5138 5139 5140
5141 5142 5143 5144 5145 5146 5147 5148 5149 5150 5151
5152 5153 5155 5156 5158 5159 5161 5162 5163 5165 5166
5167 5168 5170 5171 5172 5174 5175 5176 5178 5179 5181
5182 5183 5184 5185 5187 5188 5189 5190 5191 5194 5195
5196 5198 5200 5201 5202 5203 5204 5206 5207 5209 5211
5212 5213 5214 5215 5216 5217 5218 5220 5221 5222 5223
5224 5225 5226 5228 5229 5230 5231 5232 5234 5236 5238
5240 5242 5243 5245 5246 5248 5249 5250 5252 5253 5255
5258 5259 5260 5262 5263 5264 5266 5268 5270 5272 5274
5276 5278 5281 5283 5288 5289 5290 5291 5296 5298 5299
5301 5302 5304 5305 5307 5308 5310 5311 5312 5313 5315
5316 5318 5319 5320 5322 5323 5324 5325 5326 5329 5331
5333 5334 5335 5337 5339 5341 5342 5344 5347 5348 5349
5351 5352 5353 5355 5356 5358 5359 5360 5361 5362 5363
5364 5365 5367 5369 5370 5371 5372 5373 5375 5378 5379
5381 5384 5386 5387 5390 5391 5393 5394 5395 5396 5397
5398 5399 5401 5403 5405 5407 5408 5410 5411 5414 5415
5416 5417 5419 5420 5421 5423 5425 5426 5428 5429 5430
5431 5433 5434 5436 5437 5440 5441 5442 5443 5446 5448
5449 5452 5453 5454 5455 5458 5460 5461 5463 5464 5466
5468 5471 5472 5473 5474 5476 5477 5479 5480 5482 5483
5484 5486 5487 5488 5489 5491 5492 5493 5494 5496 5497
5498 5499 5501 5502 5503 5505 5506 5507 5508 5510 5511
5512 5514 5515 5516 5517 5518 5520 5521 5522 5524 5525
5526 5527 5530 5531 5532 5533 5536 5537 5539 5540 5541
5542 5544 5547 5548 5550 5551 5552 5553 5554 5556 5557
5559 5560 5561 5562 5564 5565 5566 5568 5570 5571 5572
5574 5576 5577 5578 5579 5580 5581 5583 5585 5586 5587
5589 5590 5591 5592 5593 5595 5596 5597 5598 5599 5600
5601 5602 5604 5605 5607 5608 5610 5611 5612 5613 5614
5615 5616 5617 5618 5619 5620 5621 5622 5624 5625 5626
5627 5628 5629 5630 5631 5632 5634 5635 5637 5638 5639
5640 5641 5642 5643 5645 5646 5648 5649 5651 5652 5653
5654 5656 5657 5658 5660 5661 5662 5664 5665 5666 5668
5669 5671 5672 5673 5675 5676 5677 5679 5680 5682 5683
5685 5686 5687 5688 5690 5691 5692 5693 5694 5695 5697
5701 5702 5703 5706 5707 5708 5710 5711 5712 5713 5714
5716 5717 5718 5719 5721 5722 5723 5724 5725 5726 5727
5729 5730 5731 5732 5734 5735 5737 5738 5739 5740 5741
5742 5744 5746 5748 5749 5750 5752 5754 5756 5757 5759
5760 5762 5764 5766 5769 5771 5772 5773 5775 5776 5777
5778 5780 5782 5784 5785 5791 5793 5794 5796 5797 5799
5801 5802 5804 5805 5806 5807 5809 5811 5812 5813 5814
5815 5816 5817 5818 5819 5821 5822 5823 5824 5828 5829
5830 5831 5832 5833 5835 5837 5839 5840 5841 5844 5845
5846 5847 5848 5850 5851 5852 5853 5856 5857 5858 5859
5861 5862 5863 5864 5866 5867 5869 5870 5871 5873 5874
5875 5877 5878 5879 5880 5882 5883 5885 5887 5888 5889
5891 5892 5893 5894 5896 5897 5898 5900 5901 5902 5903
5905 5906 5908 5911 5912 5914 5915 5917 5918 5921 5923
5924 5925 5926 5927 5928 5929 5930 5931 5933 5934 5935
5937 5940 5942 5943 5945 5948 5950 5951 5952 5954 5956
5957 5959 5962 5964 5965 5967 5968 5970 5971 5972 5974
MSN CONFIGURATION
5976 5977 5979 5981 5982 5984 5985 5986 5988 5989 5990
5992 5993 5995 5996 5997 5999 6000 6001 6003 6004 6006
6007 6008 6010 6011 6012 6014 6015 6017 6018 6019 6021
6022 6023 6025 6026 6028 6029 6030 6032 6033 6034 6036
6037 6039 6041 6043 6044 6045 6047 6048 6050 6051 6054
6055 6057 6058 6060 6061 6062 6064 6065 6066 6069 6071
6072 6073 6075 6076 6077 6078 6079 6080 6081 6082 6084
6086 6088 6090 6091 6092 6093 6095 6096 6098 6102 6103
6105 6106 6107 6109 6110 6111 6112 6113 6115 6117 6118
6120 6123 6124 6125 6127 6128 6129 6131 6134 6135 6136
6137 6139 6140 6141 6142 6145 6147 6149 6151 6153 6155
6157 6158 6161 6164 6166 6169 6170 6171 6173 6176 6177
6178 6180 6182 6183 6184 6187 6188 6189 6192 6193 6195
6197 6198 6200 6202 6204 6206 6207 6208 6209 6212 6213
6215 6216 6217 6218 6220 6223 6224 6225 6226 6228 6229
6231 6234 6235 6237 6239 6240 6242 6243 6244 6246 6247
6248 6251 6254 6257 6258 6259 6260 6262 6265 6267 6270
6274 6275 6278 6280 6281 6282 6283 6284 6285 6287 6288
6289 6290 6292 6293 6296 6297 6300 6301 6302 6304 6306
6309 6311 6315 6317 6318 6320 6321 6322 6323 6325 6327
6328 6329 6331 6332 6333 6335 6336 6338 6339 6340 6341
6343 6345 6347 6348 6350 6352 6353 6355 6356 6357 6358
6360 6361 6362 6365 6367 6369 6370 6372 6373 6374 6375
6377 6378 6379 6381 6383 6386 6388 6392 6394 6397 6400
6402 6403 6405 6408 6410 6411 6412 6413 6416 6417 6418
6421 6422 6423 6424 6426 6428 6430 6431 6434 6436 6439
6441 6442 6444 6445 6446 6447 6449 6450 6452 6455 6457
6458 6460 6462 6463 6465 6466 6467 6470 6471 6474 6476
6478 6480 6481 6483 6485 6486 6487 6489 6492 6494 6497
6498 6500 6502 6503 6505 6506 6507 6509 6510 6513 6516
6518 6521 6522 6524 6525 6527 6528 6529 6530 6533 6535
6536 6538 6540 6541 6542 6544 6546 6547 6549 6550 6551
6553 6555 6557 6559 6561 6562 6564 6565 6566 6568 6570
6571 6572 6574 6576 6577 6578 6580 6582 6583 6584 6586
6587 6589 6591 6594 6596 6597 6598 6600 6602 6604 6605
6606 6607 6608 6610 6611 6612 6614 6616 6619 6622 6624
6626 6628 6631 6633 6634 6635 6636 6637 6640 6643 6645
6646 6648 6651 6654 6655 6659 6661 6662 6664 6665 6666
6668 6669 6671 6674 6675 6676 6677 6679 6680 6681 6683
6686 6688 6689 6690 6692 6694 6695 6697 6700 6702 6704
6705 6706 6708 6710 6712 6713 6714 6715 6717 6721 6722
6724 6728 6730 6732 6733 6735 6737 6738 6739 6741 6742
6743 6746 6749 6750 6752 6753 6754 6755 6759 6764 6765
6769 6771 6773 6775 6776 6777 6778 6779 6782 6784 6785
6786 6787 6788 6789 6792 6794 6795 6800 6803 6805 6806
6807 6808 6811 6813 6815 6816 6820 6823 6824 6826 6830
6831 6832 6834 6835 6837 6838 6841 6843 6846 6847 6851
6854 6856 6857 6858 6862 6865 6870 6871 6874 6875 6876
6877 6878 6881 6882 6883 6885 6886 6888 6889 6892 6893
6896 6898 6900 6901 6902 6906 6911 6917 6918 6919 6921
6922 6924 6925 6927 6929 6931 6932 6934 6937 6939 6941
6942 6943 6944 6947 6948 6950 6951 6953 6954 6955 6958
6959 6961 6962 6963 6964 6965 6966 6969 6970 6971 6972
6974 6977 6978 6980 6981 6982 6984 6985 6986 6989 6991
6992 6993 6995 6996 6997 7000 7002 7004 7006 7008 7012
MSN CONFIGURATION
7014 7016 7017 7019 7020 7022 7024 7025 7026 7027 7028
7030 7035 7038 7039 7040 7041 7043 7044 7049 7050 7056
7057 7059 7062 7063 7066 7067 7068 7070 7071 7075 7077
7080 7082 7086 7087 7088 7091 7092 7093 7095 7096 7099
7100 7104 7109 7110 7111 7113 7115 7116 7118 7120 7121
7122 7123 7132 7134 7136 7138 7145 7148 7151 7153 7156
7158 7159 7160 7163 7164 7167 7168 7169 7170 7174 7177
7178 7183 7189 7190 7197 7200 7201 7203 7207 7210 7211
7213 7215 7216 7219 7221 7223 7224 7225 7226 7228 7231
7232 7234 7235 7238 7240 7243 7245 7247 7251 7253 7256
7258 7259 7261 7262 7263 7264 7267 7270 7272 7275 7279
7282 7289 7292 7295 7297 7302 7308 7312 7314 7315 7319
7325 7328 7337 7338 7340 7345 7347 7350 7351 7355 7356
7361 7362 7365 7370 7372 7374 7376 7377 7378 7383 7385
7389 7392 7393 7394 7397 7398 7402 7404 7405 7406 7408
7410 7411 7412 7414 7420 7421 7423 7425 7426 7431 7432
7434 7435 7437 7439 7442 7444 7447 7450 7452 7453 7456
7457 7458 7460 7463 7464 7465 7467 7469 7473 7474 7476
7482 7485 7487 7490 7491 7496 7497 7502 7503 7513 7527
7531 7534 7537 7542 7543 7545 7549 7550 7556 7561 7569
7572 7574 7580 7582 7583 7585 7593 7595 7597 7604 7605
7608 7609 7614 7615 7619 7620 7622 7624 7625 7630 7632
7633 7635 7637 7640 7643 7644 7646 7653 7654 7656 7657
7659 7660 7664 7665 7666 7669 7670 7673 7679 7681 7683
7685 7687 7691 7693 7695 7696 7699 7701 7704 7712 7713
7716 7717 7718 7724 7725 7728 7730 7740 7742 7743 7745
7747 7748 7750 7760 7761 7762 7766 7767 7771 7772 7773
7779 7780 7781 7784 7785 7789 7792 7796 7797 7805 7806
7808 7809 7816 7817 7819 7823 7829 7832 7836 7838 7843
7846 7905 7909
CONF 004
MSN CONFIGURATION
0970 0995 1928 2107 3106 3130 3146 3191 3207 3212 3217 004
3222 3229 3233 3235 3241 3247 3249 3251 3254 3262 3265
3267 3274 3283 3290 3294 3297 3302 3307 3315 3322 3326
3329 3334 3339 3340 3350 3355 3360 3367 3369 3372 3382
3387 3397 3399 3401 3405 3419 3429 3434 3441 3458 3459
3462 3471 3493 3498 3504 3507 3512 3522 3523 3525 3527
3539 3546 3552 3557 3566 3573 3575 3583 3584 3587 3592
3593 3600 3612 3619 3623 3625 3629 3633 3636 3637 3639
3645 3653 3655 3665 3669 3673 3678 3681 3682 3688 3708
3712 3717 3722 3725 3730 3737 3738 3740 3749 3752 3761
3764 3766 3784 3792 3796 3806 3814 3816 3820 3830 3847
3858 3862 3864 3867 3869 3878 3879 3881 3884 3893 3899
3916 3920 3924 3926 3928 3930 3934 3936 3938 3940 3944
3948 3951 3955 3960 3964 3966 3969 3973 3977 3981 3987
3989 3993 3996 4002 4005 4009 4016 4022 4025 4031 4041
4044 4045 4047 4050 4054 4058 4062 4067 4073 4074 4078
4082 4085 4091 4096 4099 4103 4107 4112 4116 4123 4131
4134 4136 4138 4142 4148 4155 4173 4180 4184 4189 4194
4198 4209 4213 4217 4221 4224 4230 4251 4266 4271 4274
4277 4280 4283 4292 4299 4311 4315 4318 4334 4338 4341
4352 4358 4360 4369 4374 4377 4382 4387 4406 4416 4420
MSN CONFIGURATION
4430 4461 4467 4472 4494 4500 4530 4534 4538 4542 4545
4560 4570 4577 4585 4590 4607 4611 4617 4626 4638 4643
4648 4654 4662 4669 4672 4682 4698 4703 4706 4710 4719
4728 4731 4737 4746 4753 4761 4771 4779 4783 4788 4792
4811 4819 4824 4826 4830 4834 4838 4843 4847 4850 4856
4863 4873 4881 4885 4893 4898 4901 4916 4923 4925 4932
4935 4940 4945 4949 4957 4960 4962 4966 4971 4976 4994
5009 5025 5028 5035 5038 5044 5049 5054 5059 5065 5074
5077 5083 5087 5099 5118 5124 5126 5133 5154 5160 5164
5169 5173 5177 5180 5186 5192 5197 5199 5205 5210 5227
5233 5235 5237 5241 5244 5247 5251 5254 5257 5265 5269
5271 5275 5279 5282 5285 5287 5292 5295 5297 5300 5303
5306 5309 5314 5317 5321 5328 5332 5336 5340 5343 5346
5350 5354 5357 5368 5374 5377 5382 5385 5388 5392 5402
5404 5409 5413 5418 5422 5427 5432 5435 5438 5444 5447
5450 5456 5459 5462 5465 5469 5470 5475 5481 5485 5490
5495 5500 5504 5509 5513 5519 5523 5528 5534 5538 5543
5546 5549 5555 5558 5567 5573 5575 5582 5584 5588 5594
5603 5606 5633 5636 5644 5647 5655 5659 5663 5667 5670
5674 5681 5684 5689 5696 5699 5705 5709 5715 5720 5728
5733 5736 5743 5747 5751 5755 5758 5763 5767 5770 5774
5779 5783 5787 5790 5795 5800 5803 5808 5820 5825 5834
5836 5838 5843 5849 5854 5860 5865 5872 5876 5881 5884
5890 5895 5899 5904 5909 5913 5916 5919 5922 5932 5936
5938 5939 5946 5947 5949 5955 5958 5960 5961 5966 5969
5975 5980 5983 5987 5991 5994 5998 6002 6005 6009 6013
6016 6020 6024 6027 6031 6035 6038 6042 6046 6049 6053
6056 6059 6063 6067 6070 6074 6083 6087 6089 6094 6097
6100 6104 6108 6114 6119 6121 6122 6126 6130 6133 6138
6143 6146 6148 6152 6156 6159 6162 6163 6165 6168 6172
6175 6179 6181 6185 6186 6190 6194 6196 6199 6201 6203
6205 6210 6211 6214 6219 6221 6222 6227 6230 6232 6233
6236 6238 6241 6245 6249 6252 6253 6255 6256 6261 6264
6266 6268 6271 6272 6273 6276 6279 6291 6294 6295 6299
6303 6305 6308 6312 6313 6314 6316 6319 6324 6326 6330
6334 6337 6342 6344 6346 6351 6354 6359 6363 6364 6366
6371 6376 6382 6385 6387 6389 6390 6395 6396 6398 6399
6401 6406 6407 6409 6414 6415 6420 6425 6427 6432 6433
6435 6438 6440 6443 6448 6451 6454 6459 6461 6468 6472
6473 6475 6477 6479 6482 6484 6488 6490 6493 6495 6499
6501 6504 6508 6511 6512 6515 6517 6520 6523 6526 6531
6532 6534 6537 6539 6543 6545 6548 6554 6556 6558 6560
6563 6567 6569 6573 6575 6579 6581 6585 6590 6592 6599
6601 6609 6613 6615 6618 6621 6623 6625 6627 6629 6630
6632 6638 6639 6641 6647 6649 6650 6652 6653 6656 6657
6658 6660 6663 6667 6670 6672 6678 6682 6684 6685 6687
6691 6693 6696 6698 6701 6703 6707 6709 6711 6718 6719
6723 6725 6726 6729 6731 6734 6736 6740 6745 6747 6748
6751 6756 6757 6758 6760 6761 6762 6763 6766 6767 6768
6770 6774 6780 6781 6783 6790 6791 6793 6796 6797 6798
6802 6804 6809 6810 6812 6814 6817 6818 6821 6822 6825
6827 6828 6840 6842 6844 6845 6848 6850 6852 6853 6855
6859 6861 6863 6866 6867 6869 6872 6873 6879 6880 6884
6887 6891 6894 6895 6897 6899 6903 6905 6908 6909 6910
6912 6913 6915 6916 6926 6928 6930 6933 6935 6936 6938
MSN CONFIGURATION
6940 6945 6949 6956 6957 6960 6968 6973 6976 6979 6983
6987 6988 6990 6994 6998 6999 7003 7005 7007 7009 7010
7013 7015 7018 7021 7023 7029 7032 7034 7036 7037 7042
7045 7046 7048 7052 7054 7055 7058 7064 7065 7069 7072
7073 7076 7079 7081 7084 7085 7089 7090 7097 7098 7101
7105 7106 7108 7114 7117 7119 7125 7127 7128 7130 7131
7133 7135 7137 7139 7142 7143 7144 7146 7152 7154 7155
7157 7161 7166 7171 7173 7176 7179 7180 7182 7184 7187
7188 7191 7193 7194 7196 7198 7199 7202 7204 7206 7208
7212 7217 7218 7220 7222 7227 7229 7230 7237 7239 7241
7242 7244 7246 7248 7250 7254 7255 7257 7260 7265 7266
7271 7274 7276 7278 7280 7285 7286 7287 7288 7294 7296
7298 7299 7300 7301 7303 7305 7306 7307 7310 7311 7313
7316 7317 7320 7322 7324 7326 7332 7335 7336 7339 7342
7344 7346 7348 7349 7353 7357 7358 7360 7363 7366 7368
7369 7371 7375 7379 7382 7384 7388 7390 7395 7400 7403
7407 7413 7415 7416 7418 7419 7422 7424 7427 7430 7433
7438 7440 7443 7445 7446 7448 7451 7454 7455 7461 7462
7468 7471 7478 7481 7488 7492 7493 7498 7500 7506 7509
7511 7515 7516 7518 7519 7520 7522 7524 7525 7528 7529
7532 7536 7539 7541 7551 7552 7557 7558 7562 7564 7566
7570 7573 7575 7578 7584 7586 7590 7596 7599 7601 7607
7611 7613 7617 7621 7623 7627 7628 7631 7636 7641 7645
7647 7650 7651 7652 7655 7658 7661 7667 7668 7674 7675
7678 7680 7684 7686 7689 7690 7692 7700 7702 7706 7714
7715 7720 7722 7726 7729 7732 7734 7736 7739 7741 7749
7752 7754 7756 7758 7759 7763 7769 7774 7775 7782 7783
7787 7793 7798 7801 7810 7815 7818 7820 7821 7825 7826
7830 7831 7833 7855 7870
CONF ALL
(4) Configuration definition
CONF 001
Configuration 001
CONF 001 is applicable for all A318 aircraft.
CONF 002
Configuration 002
CONF 002 is applicable for all A319 aircraft.
CONF 003
Configuration 003
CONF 003 is applicable for all A320 aircraft.
CONF 004
Configuration 004
CONF 004 is applicable for for all A321 aircraft.
CONF ALL
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
Several operators have reported loose or missing screws at the X-brackets, Y-
brackets and connecting plates of their Over Head Stowage Compartments (OHSC).
Investigations and a sampling program have shown that fuselage deflections (due
to pressure and temperature differences caused during a regular flight cycle) lead
to loads on the secondary X-load path in the OHSC. This is the root cause of the
screws loosening. The aircraft affected by this Service Bulletin are equipped with the
Enhanced Cabin configuration.
(2) Objective/Action
This Service Bulletin replaces the current screws in the X-brackets, Y-brackets and
connecting plates with threaded pins with applied micro-encapsulated coating and
additional self-locking nuts.
(3) Advantages
The embodiment of this Service Bulletin will improve the robustness of the OHSC
fixation system thus avoiding further unscheduled maintenance in this area.
(4) Operational/Maintenance Consequences
None
D. DESCRIPTION
To accomplish this Service Bulletin it is necessary to:
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
CONF 001
1 Modify the Left Hand (LH) Over Head Stowage Compartments (OHSC's)
CONF 002
1 Modify the Left Hand (LH) Over Head Stowage Compartments (OHSC's)
CONF 003
1 Modify the Left Hand (LH) Over Head Stowage Compartments (OHSC's)
CONF 004
1 Modify the Left Hand (LH) Over Head Stowage Compartments (OHSC's)
CONF 001
2 Modify the Right Hand (RH) Over Head Stowage Compartments (OHSC's)
CONF 002
2 Modify the Right Hand (RH) Over Head Stowage Compartments (OHSC's)
CONF 003
2 Modify the Right Hand (RH) Over Head Stowage Compartments (OHSC's)
CONF 004
2 Modify the Right Hand (RH) Over Head Stowage Compartments (OHSC's)
CONF ALL
(2) Additional Work
(a) Task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional Work for
Aircraft Modified by Revision No. 00
CONF 001
1 Check Dimension of the Threaded Pins of the Left Hand (LH) Over Head
Stowage Compartments (OHSC's)
CONF 002
1 Check Dimension of the Threaded Pins of the Left Hand (LH) Over Head
Stowage Compartments (OHSC's)
CONF 003
1 Check Dimension of the Threaded Pins of the Left Hand (LH) Over Head
Stowage Compartments (OHSC's)
CONF 004
1 Check Dimension of the Threaded Pins of the Left Hand (LH) Over Head
Stowage Compartments (OHSC's)
CONF 001
2 Check Dimension of the Threaded Pins of the Right Hand (RH) OHSC's
CONF 002
2 Check Dimension of the Threaded Pins of the Right Hand (RH) OHSC's
CONF 003
2 Check Dimension of the Threaded Pins of the Right Hand (RH) OHSC's
CONF 004
2 Check Dimension of the Threaded Pins of the Right Hand (RH) OHSC's
CONF ALL
E. COMPLIANCE
(1) Classification
MANDATORY: Service Bulletin must be accomplished.
(2) Accomplishment Timescale
Accomplishment of this Service Bulletin must be done within 72 months after issuance
of the original issue of this Service Bulletin.
This Service Bulletin has been classified Mandatory. It is expected that an
Airworthiness Directive (AD) published by the European Aviation Safety Agency (EASA)
will be issued to confirm this classification. It is anticipated that the AD will confirm
the threshold given but reference should be made to the AD for confirmation of the
mandated accomplishment timescale.
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the applicability has a modification or repair embodied that is not
of AIRBUS origin, and which affects the content of this Service Bulletin, the operator
is responsible for obtaining approval by its airworthiness authority for any adaptation
necessary before incorporation of the Service Bulletin.
G. MANPOWER
CONF 001
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Modify the Left Hand (LH) Over Head Stowage 10.00 h
Compartments (OHSC's)
Modify the Right Hand (RH) Over Head Stowage 10.00 h
Compartments (OHSC's)
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 8.00 h
TOTAL MAN-HOURS 36.00 h
ELAPSED TIME (HOURS) 13.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart.
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Check Dimension of the Threaded Pins of the Left Hand 0.75 h
(LH) Over Head Stowage Compartments (OHSC's)
Check Dimension of the Threaded Pins of the Right Hand 1.50 h
(RH) OHSC's
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 8.00 h
TOTAL MAN-HOURS 18.25 h
ELAPSED TIME (HOURS) 8.75 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart - Additional Work.
CONF 002
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Modify the Left Hand (LH) Over Head Stowage 10.00 h
Compartments (OHSC's)
Modify the Right Hand (RH) Over Head Stowage 10.00 h
Compartments (OHSC's)
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 8.00 h
TOTAL MAN-HOURS 36.00 h
ELAPSED TIME (HOURS) 13.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart.
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Check Dimension of the Threaded Pins of the Left Hand 0.75 h
(LH) Over Head Stowage Compartments (OHSC's)
Check Dimension of the Threaded Pins of the Right Hand 1.50 h
(RH) OHSC's
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 8.00 h
TOTAL MAN-HOURS 18.25 h
ELAPSED TIME (HOURS) 8.75 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart - Additional Work.
CONF 003
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Modify the Left Hand (LH) Over Head Stowage 11.00 h
Compartments (OHSC's)
Modify the Right Hand (RH) Over Head Stowage 11.00 h
Compartments (OHSC's)
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 8.00 h
TOTAL MAN-HOURS 38.00 h
ELAPSED TIME (HOURS) 13.50 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart.
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Check Dimension of the Threaded Pins of the Left Hand 1.00 h
(LH) Over Head Stowage Compartments (OHSC's)
Check Dimension of the Threaded Pins of the Right Hand 1.50 h
(RH) OHSC's
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 8.00 h
TOTAL MAN-HOURS 18.50 h
ELAPSED TIME (HOURS) 9.00 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart - Additional Work.
CONF 004
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also
not included.
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
PREPARATION
Job Set-up 8.00 h
PROCEDURE
Modify the Left Hand (LH) Over Head Stowage 13.00 h
Compartments (OHSC's)
Modify the Right Hand (RH) Over Head Stowage 13.00 h
Compartments (OHSC's)
PREPARATION FOR TEST
None
TEST
None
CLOSE-UP
Close-up 8.00 h
TOTAL MAN-HOURS 42.00 h
ELAPSED TIME (HOURS) 14.50 h
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart.
PREPARATION
Job Set-up 8.00 h
PROCEDURE
NOTE: For an explanation of the man-hours and elapsed time, refer to the
Gantt Chart given in Appendix Manpower Gantt Chart - Additional Work.
CONF ALL
H. WEIGHT AND BALANCE
CONF 001
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. For the definition
of MEW and operator's items, refer to Ref. WBM.
Manufacturer's Empty Weight +0.3 kg (+0.661 lb)
Effect on Balance +4.3 kg.m (+31.102 lb.ft)
CONF 002
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. For the definition
of MEW and operator's items, refer to Ref. WBM.
Manufacturer's Empty Weight +0.3 kg (+0.661 lb)
Effect on Balance +5.1 kg.m (+36.888 lb.ft)
CONF 003
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. For the definition
of MEW and operator's items, refer to Ref. WBM.
Manufacturer's Empty Weight +0.3 kg (+0.661 lb)
Effect on Balance +6.2 kg.m (+44.845 lb.ft)
CONF 004
The weight and balance estimates given in this Service Bulletin are based on the
Manufacturer's Empty Weight (MEW) and do not include operator's items. For the definition
of MEW and operator's items, refer to Ref. WBM.
Manufacturer's Empty Weight +0.5 kg (+1.102 lb)
Effect on Balance +12.8 kg.m (+92.582 lb.ft)
CONF ALL
I. ELECTRICAL LOAD DATA
Not changed
J. REFERENCES
CONF 001
(1) Modification
(a) Task set A320-A-25-XX-1BGK-01000-93AA-A Modification
2. MATERIAL INFORMATION
A. MATERIAL APPLICABILITY
CONF 001
Material for task set A320-A-25-XX-1BGK-01000-93AA-A Modification
CONF 004
Material for task set A320-A-25-XX-1BGK-01000-93AA-A Modification
CONF 003
Part kit 251BGKD03R02
obtained through the AIRBUS Spares portal or through a request for quotation to
[email protected].
CONF 003
Components for task set A320-A-25-XX-1BGK-01000-93BA-A Inspection - Addtional
Work for Aircraft Modified by Revision No. 00
3. ACCOMPLISHMENT INSTRUCTIONS
Task set A320-A-25-XX-1BGK-01000-93AA-A
Modification
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
CONF 003
TOTAL MAN-HOURS 38.00 h
CONF 004
TOTAL MAN-HOURS 42.00 h
CONF 001
ELAPSED TIME (HOURS) 13.00h
CONF 002
ELAPSED TIME (HOURS) 13.00h
CONF 003
ELAPSED TIME (HOURS) 13.50h
CONF 004
ELAPSED TIME (HOURS) 14.50h
CONF ALL
B. PREPARATION
(1) Task A320-A-25-XX-1BGK-01001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 8.00 h
Minimum Number of person 2
Elapsed Time 4.00h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
Task 12-34-24-869-002
Task 25-23-48-000-001
AMM
Task 25-24-41-000-001
Task 25-25-11-000-001
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter 'Introduction -
Aircraft status for maintenance' in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task
12-34-24-869-002.
(b) Remove the section hoses as necessary, refer to Ref. AMM Task
25-25-11-000-001.
(c) Remove the cove light panels, refer to Ref. AMM Task 25-23-48-000-001.
(d) Remove the cover panels, refer to Ref. AMM Task 25-24-41-000-001.
C. PROCEDURE
CONF 001
(1) Task A320-A-25-XX-1BGK-01001-920A-A - Modify the Left Hand (LH) Over
Head Stowage Compartments (OHSC's)
Man-hours 10.00 h
Minimum Number of person 2
Elapsed Time 5.00h
Skills Cabin
Material necessary to do the job
Part kit 251BGKD01R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 53 PIN
11 NAS1149CN832R 247 WASHER
12 MS21042-08 247 NUT
13 FAS000033-000 194 PIN
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the LH OHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 2,
View C and Section A-A:
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the LH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 10 must fully install the
pins into the inserts.
(d) On the LH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
Ibf.in.).
(e) From the LH OHSC's remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 3,
View D and Section C-C:
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the LH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(g) On the LH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) From the LH OHSC's remove the fasteners from the Inter-Bin Connecting Plates
(ICPs), refer to Ref. Fig. Modify the LH/RH Over Head Stowage Compartments
(OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over Head Stowage
Compartments (OHSC's) SHEET 4, View E and Section E-E:
(i) On the LH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(j) On the LH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
CONF 001
Z260
Z250
Z240
Z230
C
A D
C
D
C E
D
C E C
D D
E C FR43
E E
C D
C
FR39
D
C D
FR34
D C
FR26 A 01 D
C
TYPICAL
FR21 D E E
C D
D
E C
C E E D
D C
FR66
E D
E C FR63
D FR59
E C
D
FR47
B 01
FR43
TYPICAL
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-000BM-A-002-01
CONF 001
AFFECTED
A FASTENERS
B
A
B
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
BEFORE
X-BRACKET BACK
PANEL
03
INSERT
BOTTOM 10
PANEL
12
A A 11
B B BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BN-A-004-01
CONF 001
AFFECTED
FASTENERS
C
D
C
D D
TYPICAL Y-BRACKET
(10 FASTENERS MAX) AFFECTED
FASTENERS
BOTTOM
PANEL
(11) (11)
Y-BRACKET (3) (3)
C C
BOTTOM
PANEL
11 11
Y-BRACKET
12 12
13 13 04
05
D D
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BO-A-004-01
CONF 001
AFFECTED
FASTENERS
AFFECTED
FASTENERS
E
F
E
E F
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
TOP/BOTTOM
PANEL
(11) (11)
CONNECTING (4) (4)
PLATE
E E
TOP/BOTTOM
PANEL
11 11
CONNECTING
PLATE 12 12
13 13 06
07
NOTE:
F F
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BP-A-004-01
CONF 002
(1) Task A320-A-25-XX-1BGK-01002-920A-A - Modify the Left Hand (LH) Over
Head Stowage Compartments (OHSC's)
Man-hours 10.00 h
Minimum Number of person 2
Elapsed Time 5.00h
Skills Cabin
Material necessary to do the job
Part kit 251BGKD02R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 60 PIN
11 NAS1149CN832R 274 WASHER
12 MS21042-08 274 NUT
13 FAS000033-000 214 PIN
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the LH OHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 2,
View C and Section A-A:
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the LH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 10 must fully install the
pins into the inserts.
(d) On the LH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(e) From the LH OHSC's remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 3,
View D and Section C-C:
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the LH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Sction D-D,
install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(g) On the LH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) From the LH OHSC's remove the fasteners from the Inter-Bin Connecting Plates
(ICPs), refer to Ref. Fig. Modify the LH/RH Over Head Stowage Compartments
(OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over Head Stowage
Compartments (OHSC's) SHEET 4, View E and Section E-E:
(i) On the LH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 58
A318/A319/A320/A321
SERVICE BULLETIN
(j) On the LH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
CONF 002
Z260
Z250
Z240
Z230
B
C
D
A D
C
D E
C E
D C
E
C
D
D
C D
E FR43
E E D
C FR39
C
FR36
D
C FR30
D
D C
FR26 A 01 D
TYPICAL C
FR21 D E
E
C
D D
E C
C
D D
E C
C
FR66
D D
E C FR63
D
C FR59
D
FR43 E C FR55
D B 01
FR47
TYPICAL
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-000BQ-A-003-01
CONF 002
AFFECTED
A FASTENERS
B
A
B
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
BEFORE
AFTER
X-BRACKET BACK
PANEL 02
(11)
(1) INSERT
X-BRACKET BACK
PANEL
03
INSERT
BOTTOM 10
PANEL 12
11
A A
B B BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BR-A-004-01
CONF 002
AFFECTED
FASTENERS
C
D
C
D D
TYPICAL Y-BRACKET AFFECTED
(10 FASTENERS MAX) FASTENERS
BOTTOM
PANEL
(11) (11)
Y-BRACKET (3) (3)
C C
BOTTOM
PANEL
11 11
Y-BRACKET
12 12
13 13 04
05
D D
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BS-A-004-01
CONF 002
AFFECTED
FASTENERS
AFFECTED
FASTENERS
E
F
E
E F
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL
BEFORE INSERT
TOP/BOTTOM
PANEL
(11) (11)
CONNECTING (4) (4)
PLATE
E E
TOP/BOTTOM
PANEL
11 11
CONNECTING
PLATE 12 12
13 13 06
07
NOTE:
F F
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BT-A-004-01
CONF 003
(1) Task A320-A-25-XX-1BGK-01003-920A-A - Modify the Left Hand (LH) Over
Head Stowage Compartments (OHSC's)
Man-hours 11.00 h
Minimum Number of person 2
Elapsed Time 5.50h
Skills Cabin
Material necessary to do the job
Part kit 251BGKD03R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 73 PIN
11 NAS1149CN832R 304 WASHER
12 MS21042-08 304 NUT
13 FAS000033-000 231 PIN
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the LH OHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 2,
View C and Section A-A:
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the LH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 10 must fully install the
pins into the inserts.
(d) On the LH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(e) From the LH OHSC's remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 3,
View D and Section C-C:
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the LH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(g) On the LH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) From the LH OHSC's remove the fasteners from the Inter-Bin Connecting Plates
(ICPs), refer to Ref. Fig. Modify the LH/RH Over Head Stowage Compartments
(OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over Head Stowage
Compartments (OHSC's) SHEET 4, View E and Section E-E:
(i) On the LH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 66
A318/A319/A320/A321
SERVICE BULLETIN
(j) On the LH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
CONF 003
Z260
Z250
Z240
Z230
C
B D
C
D
A E
C
D
E C
C
D D
E C FR43
C
D D
E C FR39
E E D
C
C FR34
D D
C C
FR30 A 01
D
D TYPICAL C
FR26 D E
E
C
FR21 D
E
C
D D
E C
C
FR66
D D
E C FR63
C
D D
E C FR59
D
E C FR55
D
FR43 C FR51
D B 01
FR47
TYPICAL
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-000BU-A-003-01
CONF 003
AFFECTED
A FASTENERS
B
A
B
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
BEFORE
AFTER
X-BRACKET BACK
PANEL 02
(11)
(1) INSERT
X-BRACKET BACK
PANEL
03
INSERT
BOTTOM 10
PANEL 12
11
A A
B B BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BV-A-004-01
CONF 003
AFFECTED
FASTENERS
C
D
C
D D
TYPICAL Y-BRACKET AFFECTED
(10 FASTENERS MAX) FASTENERS
BOTTOM
PANEL
(11) (11)
Y-BRACKET (3) (3)
C C
BOTTOM
PANEL
11 11
Y-BRACKET
12 12
13 13 04
05
D D
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BW-A-004-01
CONF 003
AFFECTED
FASTENERS
AFFECTED
FASTENERS
E
F
E
E F
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL
BEFORE INSERT
TOP/BOTTOM
PANEL
(11) (11)
CONNECTING (4) (4)
PLATE
E E
TOP/BOTTOM
PANEL
11 11
CONNECTING
PLATE 12 12
13 13 06
07
NOTE:
F F
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BX-A-004-01
CONF 004
(1) Task A320-A-25-XX-1BGK-01004-920A-A - Modify the Left Hand (LH) Over
Head Stowage Compartments (OHSC's)
Man-hours 13.00 h
Minimum Number of person 2
Elapsed Time 6.50h
Skills Cabin
Material necessary to do the job
Part kit 251BGKD04R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 99 PIN
11 NAS1149CN832R 532 WASHER
12 MS21042-08 532 NUT
13 FAS000033-000 433 PIN
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the LH OHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 2,
View C and Section A-A:
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the LH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 10 must fully install the
pins into the inserts.
(d) On the LH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(e) From the LH OHSC's remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 3,
View D and Section C-C:
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the LH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(g) On the LH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) From the LH OHSC's remove the fasteners from the Inter-Bin Connecting Plates
(ICPs), refer to Ref. Fig. Modify the LH/RH Over Head Stowage Compartments
(OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over Head Stowage
Compartments (OHSC's) SHEET 4, View E and Section E-E:
(i) On the LH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 74
A318/A319/A320/A321
SERVICE BULLETIN
(j) On the LH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
CONF 004
Z260
Z250
C
Z240 D
C
Z230
D
B C E
D E
C
C E
A D D
C E C FR43
D D
C E C FR39
E
D D
C E FR35.7
D C FR35.5
E D
C FR35.3
E E C
D
C FR35.1 D D
C FR34 C
D D
C A 01
E
C
FR30 TYPICAL
D D
E
FR26 C
D D
FR21 C E C
D D
E C FR64
C E D
D C FR59
C
D
D FR55
C
E D FR51
C
D FR47.5 B 01
E C
FR43 TYPICAL
FR47.2
D
FR47
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-000BY-A-002-01
CONF 004
AFFECTED
A FASTENERS
B
A
B
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
BEFORE
AFTER
X-BRACKET BACK
PANEL 02
(11)
(1) INSERT
X-BRACKET BACK
PANEL
03
INSERT
BOTTOM 10
PANEL 12
11
A A
B B BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BZ-A-004-01
CONF 004
AFFECTED
FASTENERS
C
D
C
D D
TYPICAL Y-BRACKET AFFECTED
(10 FASTENERS MAX) FASTENERS
BOTTOM
PANEL
(11) (11)
Y-BRACKET (3) (3)
C C
BOTTOM
PANEL
11 11
Y-BRACKET
12 12
13 13 04
05
D D
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000C0-A-004-01
CONF 004
AFFECTED
FASTENERS
AFFECTED
FASTENERS
E
F
E
E F
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL
BEFORE INSERT
TOP/BOTTOM
PANEL
(11) (11)
CONNECTING (4) (4)
PLATE
E E
TOP/BOTTOM
PANEL
11 11
CONNECTING
PLATE 12 12
13 13 06
07
NOTE:
F F
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000C1-A-004-01
CONF 001
(2) Task A320-A-25-XX-1BGK-02001-920A-A - Modify the Right Hand (RH) Over
Head Stowage Compartments (OHSC's)
Man-hours 10.00 h
Minimum Number of person 2
Elapsed Time 5.00h
Skills Cabin
Material necessary to do the job
Part kit 251BGKD01R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 53 PIN
11 NAS1149CN832R 247 WASHER
12 MS21042-08 247 NUT
13 FAS000033-000 194 PIN
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the RH OHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 2,
View C and Section A-A:
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the RH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 10 must fully install the
pins into the inserts.
(d) On the RH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(e) From the RH OHSC's remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 3,
View D and Section C-C:
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the RH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(g) On the RH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) From the RH OHSC's remove the fasteners from the Inter-Bin Connecting Plates
(ICPs), refer to Ref. Fig. Modify the LH/RH Over Head Stowage Compartments
(OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over Head Stowage
Compartments (OHSC's) SHEET 4, View E and Section E-E:
(i) On the RH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 82
A318/A319/A320/A321
SERVICE BULLETIN
(j) On the RH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
CONF 001
Z260
Z250
Z240
Z230
C
A D
C
D
C E
D
C E C
D D
E C FR43
E E
C D
C
FR39
D
C D
FR34
D C
FR26 A 01 D
C
TYPICAL
FR21 D E E
C D
D
E C
C E E D
D C
FR66
E D
E C FR63
D FR59
E C
D
FR47
B 01
FR43
TYPICAL
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-000BM-A-002-01
CONF 001
AFFECTED
A FASTENERS
B
A
B
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
BEFORE
X-BRACKET BACK
PANEL
03
INSERT
BOTTOM 10
PANEL
12
A A 11
B B BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BN-A-004-01
CONF 001
AFFECTED
FASTENERS
C
D
C
D D
TYPICAL Y-BRACKET
(10 FASTENERS MAX) AFFECTED
FASTENERS
BOTTOM
PANEL
(11) (11)
Y-BRACKET (3) (3)
C C
BOTTOM
PANEL
11 11
Y-BRACKET
12 12
13 13 04
05
D D
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BO-A-004-01
CONF 001
AFFECTED
FASTENERS
AFFECTED
FASTENERS
E
F
E
E F
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
TOP/BOTTOM
PANEL
(11) (11)
CONNECTING (4) (4)
PLATE
E E
TOP/BOTTOM
PANEL
11 11
CONNECTING
PLATE 12 12
13 13 06
07
NOTE:
F F
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BP-A-004-01
CONF 002
(2) Task A320-A-25-XX-1BGK-02002-920A-A - Modify the Right Hand (RH) Over
Head Stowage Compartments (OHSC's)
Man-hours 10.00 h
Minimum Number of person 2
Elapsed Time 5.00h
Skills Cabin
Material necessary to do the job
Part kit 251BGKD02R01
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 60 PIN
11 NAS1149CN832R 274 WASHER
12 MS21042-08 274 NUT
13 FAS000033-000 214 PIN
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the RH OHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 2,
View C and Section A-A:
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the RH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 10 must fully install the
pins into the inserts.
(d) On the RH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(e) From the RH OHSC's remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 3,
View D and Section C-C:
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the RH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(g) On the RH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) From the RH OHSC's remove the fasteners from the Inter-Bin Connecting Plates
(ICPs), refer to Ref. Fig. Modify the LH/RH Over Head Stowage Compartments
(OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over Head Stowage
Compartments (OHSC's) SHEET 4, View E and Section E-E:
(i) On the RH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 90
A318/A319/A320/A321
SERVICE BULLETIN
(j) On the RH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
CONF 002
Z260
Z250
Z240
Z230
B
C
D
A D
C
D E
C E
D C
E
C
D
D
C D
E FR43
E E D
C FR39
C
FR36
D
C FR30
D
D C
FR26 A 01 D
TYPICAL C
FR21 D E
E
C
D D
E C
C
D D
E C
C
FR66
D D
E C FR63
D
C FR59
D
FR43 E C FR55
D B 01
FR47
TYPICAL
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-000BQ-A-003-01
CONF 002
AFFECTED
A FASTENERS
B
A
B
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
BEFORE
AFTER
X-BRACKET BACK
PANEL 02
(11)
(1) INSERT
X-BRACKET BACK
PANEL
03
INSERT
BOTTOM 10
PANEL 12
11
A A
B B BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BR-A-004-01
CONF 002
AFFECTED
FASTENERS
C
D
C
D D
TYPICAL Y-BRACKET AFFECTED
(10 FASTENERS MAX) FASTENERS
BOTTOM
PANEL
(11) (11)
Y-BRACKET (3) (3)
C C
BOTTOM
PANEL
11 11
Y-BRACKET
12 12
13 13 04
05
D D
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BS-A-004-01
CONF 002
AFFECTED
FASTENERS
AFFECTED
FASTENERS
E
F
E
E F
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL
BEFORE INSERT
TOP/BOTTOM
PANEL
(11) (11)
CONNECTING (4) (4)
PLATE
E E
TOP/BOTTOM
PANEL
11 11
CONNECTING
PLATE 12 12
13 13 06
07
NOTE:
F F
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BT-A-004-01
CONF 003
(2) Task A320-A-25-XX-1BGK-02003-920A-A - Modify the Right Hand (RH) Over
Head Stowage Compartments (OHSC's)
Man-hours 11.00 h
Minimum Number of person 2
Elapsed Time 5.50h
Skills Cabin
Material necessary to do the job
Part kit 251BGKD03R02
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 73 PIN
11 NAS1149CN832R 304 WASHER
12 MS21042-08 304 NUT
13 FAS000033-000 231 PIN
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the RH OHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 2,
View C and Section A-A:
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the RH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 10 must fully install the
pins into the inserts.
(d) On the RH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(e) From the RH OHSC's remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 3,
View D and Section C-C:
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the RH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(g) On the RH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) From the RH OHSC's remove the fasteners from the Inter-Bin Connecting Plates
(ICPs), refer to Ref. Fig. Modify the LH/RH Over Head Stowage Compartments
(OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over Head Stowage
Compartments (OHSC's) SHEET 4, View E and Section E-E:
(i) On the RH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 98
A318/A319/A320/A321
SERVICE BULLETIN
(j) On the RH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
CONF 003
Z260
Z250
Z240
Z230
C
B D
C
D
A E
C
D
E C
C
D D
E C FR43
C
D D
E C FR39
E E D
C
C FR34
D D
C C
FR30 A 01
D
D TYPICAL C
FR26 D E
E
C
FR21 D
E
C
D D
E C
C
FR66
D D
E C FR63
C
D D
E C FR59
D
E C FR55
D
FR43 C FR51
D B 01
FR47
TYPICAL
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-000BU-A-003-01
CONF 003
AFFECTED
A FASTENERS
B
A
B
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
BEFORE
AFTER
X-BRACKET BACK
PANEL 02
(11)
(1) INSERT
X-BRACKET BACK
PANEL
03
INSERT
BOTTOM 10
PANEL 12
11
A A
B B BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BV-A-004-01
CONF 003
AFFECTED
FASTENERS
C
D
C
D D
TYPICAL Y-BRACKET AFFECTED
(10 FASTENERS MAX) FASTENERS
BOTTOM
PANEL
(11) (11)
Y-BRACKET (3) (3)
C C
BOTTOM
PANEL
11 11
Y-BRACKET
12 12
13 13 04
05
D D
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BW-A-004-01
CONF 003
AFFECTED
FASTENERS
AFFECTED
FASTENERS
E
F
E
E F
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL
BEFORE INSERT
TOP/BOTTOM
PANEL
(11) (11)
CONNECTING (4) (4)
PLATE
E E
TOP/BOTTOM
PANEL
11 11
CONNECTING
PLATE 12 12
13 13 06
07
NOTE:
F F
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BX-A-004-01
CONF 004
(2) Task A320-A-25-XX-1BGK-02004-920A-A - Modify the Right Hand (RH) Over
Head Stowage Compartments (OHSC's)
Man-hours 13.00 h
Minimum Number of person 2
Elapsed Time 6.50h
Skills Cabin
Material necessary to do the job
Part kit 251BGKD04R03
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 99 PIN
11 NAS1149CN832R 532 WASHER
12 MS21042-08 532 NUT
13 FAS000033-000 433 PIN
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) From the RH OHSC's remove the fasteners from the X-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 2,
View C and Section A-A:
NOTE: Some X-Brackets are installed with four fasteners and some with six
fasteners.
(c) On the RH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Threaded Pins, Item 10, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 10 must fully install the
pins into the inserts.
(d) On the RH OHSC's, on the X-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 2, View C and Section B-B,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(e) From the RH OHSC’s remove the fasteners from the Y-Brackets, refer to Ref. Fig.
Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 1 and Ref.
Fig. Modify the LH/RH Over Head Stowage Compartments (OHSC's) SHEET 3,
View D and Section C-C:
NOTE: Some Y-Brackets are installed with six or eight fasteners and some with
ten fasteners.
(f) On the RH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
(g) On the RH OHSC's, on the Y-Brackets, refer to Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH
Over Head Stowage Compartments (OHSC's) SHEET 3, View D and Section D-D,
install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) From the RH OHSC's remove the fasteners from the Inter-Bin Connecting Plates
(ICPs), refer to Ref. Fig. Modify the LH/RH Over Head Stowage Compartments
(OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over Head Stowage
Compartments (OHSC's) SHEET 4, View E and Section E-E:
(i) On the RH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Threaded Pins, Item 13, given above is the maximum
required and can change on different aircraft cabin layouts.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, item 13 must fully install the
pins into the inserts.
REV 00 Oct 13/17 A320-25-1BGK
REV 01 Aug 24/18 Page 106
A318/A319/A320/A321
SERVICE BULLETIN
(j) On the RH OHSC's, on the ICP, refer to Ref. Fig. Modify the LH/RH Over Head
Stowage Compartments (OHSC's) SHEET 1 and Ref. Fig. Modify the LH/RH Over
Head Stowage Compartments (OHSC's) SHEET 4, View E and Section F-F, install:
NOTE: The quantity of Washers, Item 11, and Nuts, Item 12, given above is the
maximum required and can change on different aircraft cabin layouts.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
CONF 004
Z260
Z250
C
Z240 D
C
Z230
D
B C E
D E
C
C E
A D D
C E C FR43
D D
C E C FR39
E
D D
C E FR35.7
D C FR35.5
E D
C FR35.3
E E C
D
C FR35.1 D D
C FR34 C
D D
C A 01
E
C
FR30 TYPICAL
D D
E
FR26 C
D D
FR21 C E C
D D
E C FR64
C E D
D C FR59
C
D
D FR55
C
E D FR51
C
D FR47.5 B 01
E C
FR43 TYPICAL
FR47.2
D
FR47
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-000BY-A-002-01
CONF 004
AFFECTED
A FASTENERS
B
A
B
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
BEFORE
AFTER
X-BRACKET BACK
PANEL 02
(11)
(1) INSERT
X-BRACKET BACK
PANEL
03
INSERT
BOTTOM 10
PANEL 12
11
A A
B B BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000BZ-A-004-01
CONF 004
AFFECTED
FASTENERS
C
D
C
D D
TYPICAL Y-BRACKET AFFECTED
(10 FASTENERS MAX) FASTENERS
BOTTOM
PANEL
(11) (11)
Y-BRACKET (3) (3)
C C
BOTTOM
PANEL
11 11
Y-BRACKET
12 12
13 13 04
05
D D
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000C0-A-004-01
CONF 004
AFFECTED
FASTENERS
AFFECTED
FASTENERS
E
F
E
E F
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL
BEFORE INSERT
TOP/BOTTOM
PANEL
(11) (11)
CONNECTING (4) (4)
PLATE
E E
TOP/BOTTOM
PANEL
11 11
CONNECTING
PLATE 12 12
13 13 06
07
NOTE:
F F
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-000C1-A-004-01
CONF ALL
D. PREPARATION FOR TEST
None
E. TEST
None
F. CLOSE-UP
(1) Task A320-A-25-XX-1BGK-01001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 8.00 h
Minimum Number of person 2
Elapsed Time 4.00h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
Task 25-23-48-400-001
AMM Task 25-24-41-400-001
Task 25-25-11-400-001
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the cover panels, refer to Ref. AMM Task 25-24-41-400-001.
(c) Install the cove light panels, refer to Ref. AMM Task 25-23-48-400-001.
(d) Install the section hoses, refer to Ref. AMM Task 25-25-11-400-001.
(e) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A320-A-25-XX-1BGK-02001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given in
other documents or in other sections of the Service Bulletin. When the words “refer to”
are used and the operator has a procedure accepted by the local authority he belongs to,
the accepted alternative procedure can be used. When the words “in accordance with”
are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service Bulletin.
Operators can therefore, as deemed necessary, omit or add access and/or close-up steps
to add flexibility to their maintenance operations as long as the technical intent of the
Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Refer
to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance necessary
to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions, including RC paragraph contained herein, contact
AIRBUS for further instructions and approval.
CONF 003
TOTAL MAN-HOURS 18.50 h
CONF 004
TOTAL MAN-HOURS 19.00 h
CONF 001
ELAPSED TIME (HOURS) 8.75h
CONF 002
ELAPSED TIME (HOURS) 8.75h
CONF 003
ELAPSED TIME (HOURS) 9.00h
CONF 004
ELAPSED TIME (HOURS) 9.50h
CONF ALL
B. PREPARATION
(1) Task A320-A-25-XX-1BGK-01001-540A-A - Job Set-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 8.00 h
Minimum Number of person 2
Elapsed Time 4.00h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
Task 12-34-24-869-002
Task 25-23-48-000-001
AMM
Task 25-24-41-000-001
Task 25-25-11-000-001
Procedure
NOTE: For the basic Aircraft configuration, refer to AMM Chapter 'Introduction -
Aircraft status for maintenance' in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task
12-34-24-869-002.
(b) Remove the section hoses as necessary, refer to Ref. AMM Task
25-25-11-000-001.
(c) Remove the cove light panels, refer to Ref. AMM Task 25-23-48-000-001.
(d) Remove the cover panels, refer to Ref. AMM Task 25-24-41-000-001.
C. PROCEDURE
CONF 001
(1) Task A320-A-25-XX-1BGK-01001-720A-A - Check Dimension of the Threaded
Pins of the Left Hand (LH) Over Head Stowage Compartments (OHSC's)
Job Set-Up Information
Working Area
Man-hours 0.75 h
Minimum Number of person 1
Elapsed Time 0.75h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 1 PIN (1)
11 NAS1149CN832R 2 WASHER (1)
12 MS21042-08 2 NUT (1)
13 FAS000033-000 1 PIN (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the LH OHSC’s, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, clean any remains of adhesive from
the inserts.
(e) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, got to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the length of the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, clean any remains of adhesive from the
inserts.
(l) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3 , View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(o) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the dimensions of all the new
Threaded Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the Inter-Bin Connecting Plates (ICPs) of the LH OHSC's, refer to Ref. Fig.
Additional Work of the LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work
of the LH and RH OHSC's SHEET 4, View E and Section C-C, do a check of the
dimensions of the Threaded Pins, Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
Task A320-A-25-XX-1BGK-02ZZZ-720Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and
RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 4, View E and Section C-C, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
CONF 001
Z260
Z250
Z240
Z230
C
A D
C
D
C E
D
C E C
D D
E C FR43
E E
C D
C
FR39
D
C D
FR34
D C
FR26 A 01 D
C
TYPICAL E
FR21 D E
C D
D
E C
C E E D
D C
FR66
E D
E C FR63
D FR59
E C
D
FR47 B 01
TYPICAL
FR43
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-0090Y-A-002-01
CONF 001
AFFECTED
FASTENERS
A
A
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
02
X-BRACKET BACK
PANEL
03
INSERT
(10)
10 (12)
12
(11)
11
A A BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090Z-A-002-01
CONF 001
AFFECTED
FASTENERS
B
AFFECTED
FASTENERS
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
SIDEWALL INSERT
BOTTOM
PANEL
(11) (11)
11 11
Y-BRACKET
(12) (12)
12 12
(13) (13) 04
13 13 05
B B
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00910-A-002-01
CONF 001
AFFECTED
FASTENERS
AFFECTED
FASTENERS
C
E
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL INSERT
TOP/BOTTOM
PANEL
(11) (11)
11 11
CONNECTING (12) (12)
PLATE 12 12
(13) (13) 06
13 13 07
C C
NOTE:
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00911-A-002-01
CONF 002
(1) Task A320-A-25-XX-1BGK-01002-720A-A - Check Dimension of the Threaded
Pins of the Left Hand (LH) Over Head Stowage Compartments (OHSC's)
Job Set-Up Information
Working Area
Man-hours 0.75 h
Minimum Number of person 1
Elapsed Time 0.75h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 1 PIN (1)
11 NAS1149CN832R 2 WASHER (1)
12 MS21042-08 2 NUT (1)
13 FAS000033-000 1 PIN (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the LH OHSC’s, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, clean any remains of adhesive from
the inserts.
(e) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, got to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the length of the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, clean any remains of adhesive from the
inserts.
(l) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3 , View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(o) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the dimensions of all the new
Threaded Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the Inter-Bin Connecting Plates (ICPs) of the LH OHSC's, refer to Ref. Fig.
Additional Work of the LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work
of the LH and RH OHSC's SHEET 4, View E and Section C-C, do a check of the
dimensions of the Threaded Pins, Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
Task A320-A-25-XX-1BGK-02ZZZ-720Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and
RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 4, View E and Section C-C, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
CONF 002
Z260
Z250
Z240
Z230
B
C
D
A D
C
D E
C E
D C
E
C
D
D
C D
E FR43
E E D
C FR39
C
FR36
D
C FR30 D
D C
FR26 A 01 D
TYPICAL
C
D E
FR21 E
C
D D
E C
C
D D
E C
C
FR66
D D
E C FR63
D
C FR59
D
E C FR55
D B 01
FR47
TYPICAL
NOTE: FR43
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-0090Q-A-002-01
CONF 002
AFFECTED
FASTENERS
A
A
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
02
X-BRACKET BACK
PANEL
03
INSERT
(10)
10 (12)
12
(11)
11
A A BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090R-A-002-01
CONF 002
AFFECTED
FASTENERS
B
AFFECTED
FASTENERS
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
SIDEWALL INSERT
BOTTOM
PANEL
(11) (11)
11 11
Y-BRACKET
(12) (12)
12 12
(13) (13) 04
13 13 05
B B
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090S-A-002-01
CONF 002
AFFECTED
FASTENERS
AFFECTED
FASTENERS
C
E
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL INSERT
TOP/BOTTOM
PANEL
(11) (11)
11 11
CONNECTING (12) (12)
PLATE 12 12
(13) (13) 06
13 13 07
C C
NOTE:
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090T-A-002-01
CONF 003
(1) Task A320-A-25-XX-1BGK-01003-720A-A - Check Dimension of the Threaded
Pins of the Left Hand (LH) Over Head Stowage Compartments (OHSC's)
Job Set-Up Information
Working Area
Man-hours 1.00 h
Minimum Number of person 1
Elapsed Time 1.00h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 1 PIN (1)
11 NAS1149CN832R 2 WASHER (1)
12 MS21042-08 2 NUT (1)
13 FAS000033-000 1 PIN (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the LH OHSC’s, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, clean any remains of adhesive from
the inserts.
(e) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, got to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the length of the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, clean any remains of adhesive from the
inserts.
(l) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3 , View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(o) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the dimensions of all the new
Threaded Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the Inter-Bin Connecting Plates (ICPs) of the LH OHSC's, refer to Ref. Fig.
Additional Work of the LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work
of the LH and RH OHSC's SHEET 4, View E and Section C-C, do a check of the
dimensions of the Threaded Pins, Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
Task A320-A-25-XX-1BGK-02ZZZ-720Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and
RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 4, View E and Section C-C, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
install:
CONF 003
Z260
Z250
Z240
Z230 C
B D
C
D
E
A C
D
E C
C
D D
E C FR43
C
D D
E C FR39
E E D
C
C FR34
D D
C C
FR30 A 01 D
D
FR26
TYPICAL C
D E
E
FR21
C
D
E
C
D D
E C
C
FR66
D D
E C FR63
C
D D
E C FR59
D
E C FR55
D
C B 01
FR51
D TYPICAL
FR47
NOTE: FR43
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-00912-A-002-01
CONF 003
AFFECTED
FASTENERS
A
A
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
02
X-BRACKET BACK
PANEL
03
INSERT
(10)
10 (12)
12
(11)
11
A A BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00913-A-002-01
CONF 003
AFFECTED
FASTENERS
B
AFFECTED
FASTENERS
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
SIDEWALL INSERT
BOTTOM
PANEL
(11) (11)
11 11
Y-BRACKET
(12) (12)
12 12
(13) (13) 04
13 13 05
B B
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00914-A-002-01
CONF 003
AFFECTED
FASTENERS
AFFECTED
FASTENERS
C
E
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL INSERT
TOP/BOTTOM
PANEL
(11) (11)
11 11
CONNECTING (12) (12)
PLATE 12 12
(13) (13) 06
13 13 07
C C
NOTE:
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00915-A-002-01
CONF 004
(1) Task A320-A-25-XX-1BGK-01004-720A-A - Check Dimension of the Threaded
Pins of the Left Hand (LH) Over Head Stowage Compartments (OHSC's)
Job Set-Up Information
Working Area
Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 1 PIN (1)
11 NAS1149CN832R 2 WASHER (1)
12 MS21042-08 2 NUT (1)
13 FAS000033-000 1 PIN (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the LH OHSC’s, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, clean any remains of adhesive from
the inserts.
(e) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, got to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) On the X-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the length of the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, clean any remains of adhesive from the
inserts.
(l) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3 , View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(o) On the Y-Brackets of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the dimensions of all the new
Threaded Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the Inter-Bin Connecting Plates (ICPs) of the LH OHSC's, refer to Ref. Fig.
Additional Work of the LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work
of the LH and RH OHSC's SHEET 4, View E and Section C-C, do a check of the
dimensions of the Threaded Pins, Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
Task A320-A-25-XX-1BGK-02ZZZ-720Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and
RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 4, View E and Section C-C, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICPs of the LH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
CONF 004
Z260
Z250
C
Z240 D
C
Z230 D
B C E
D E
C
C E
A D D
C E C FR43
D D
C E C FR39
E
D D
C E FR35.7
D C FR35.5
E D
C FR35.3
C
E E D
C FR35.1 D D
C FR34 C
D D
C A 01
C E
FR30 TYPICAL D
D E
FR26 C
D D
C E C
FR21
D D
E C FR64
C E D
D C FR59
C
D
D FR55
C
E D FR51
C
D FR47.5
E C B 01
FR43
FR47.2
D TYPICAL
FR47
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-0090U-A-002-01
CONF 004
AFFECTED
FASTENERS
A
A
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
02
X-BRACKET BACK
PANEL
03
INSERT
(10)
10 (12)
12
(11)
11
A A BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090V-A-002-01
CONF 004
AFFECTED
FASTENERS
B
AFFECTED
FASTENERS
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
SIDEWALL INSERT
BOTTOM
PANEL
(11) (11)
11 11
Y-BRACKET
(12) (12)
12 12
(13) (13) 04
13 13 05
B B
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090W-A-002-01
CONF 004
AFFECTED
FASTENERS
AFFECTED
FASTENERS
C
E
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL INSERT
TOP/BOTTOM
PANEL
(11) (11)
11 11
CONNECTING (12) (12)
PLATE 12 12
(13) (13) 06
13 13 07
C C
NOTE:
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090X-A-002-01
CONF 001
(2) Task A320-A-25-XX-1BGK-02001-720A-A - Check Dimension of the Threaded
Pins of the Right Hand (RH) OHSC's
Job Set-Up Information
Working Area
Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 1 PIN (1)
11 NAS1149CN832R 2 WASHER (1)
12 MS21042-08 2 NUT (1)
13 FAS000033-000 1 PIN (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the RH OHSC’s, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, clean any remains of adhesive from
the inserts.
(e) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, got to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the length of the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, clean any remains of adhesive from the
inserts.
(l) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3 , View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(o) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the dimensions of all the new
Threaded Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the Inter-Bin Connecting Plates (ICPs) of the RH OHSC's, refer to Ref. Fig.
Additional Work of the LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work
of the LH and RH OHSC's SHEET 4, View E and Section C-C, do a check of the
dimensions of the Threaded Pins, Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
Task A320-A-25-XX-1BGK-02ZZZ-720Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 4, View E and Section C-C, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
CONF 001
Z260
Z250
Z240
Z230
C
A D
C
D
C E
D
C E C
D D
E C FR43
E E
C D
C
FR39
D
C D
FR34
D C
FR26 A 01 D
C
TYPICAL E
FR21 D E
C D
D
E C
C E E D
D C
FR66
E D
E C FR63
D FR59
E C
D
FR47 B 01
TYPICAL
FR43
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-0090Y-A-002-01
CONF 001
AFFECTED
FASTENERS
A
A
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
02
X-BRACKET BACK
PANEL
03
INSERT
(10)
10 (12)
12
(11)
11
A A BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090Z-A-002-01
CONF 001
AFFECTED
FASTENERS
B
AFFECTED
FASTENERS
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
SIDEWALL INSERT
BOTTOM
PANEL
(11) (11)
11 11
Y-BRACKET
(12) (12)
12 12
(13) (13) 04
13 13 05
B B
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00910-A-002-01
CONF 001
AFFECTED
FASTENERS
AFFECTED
FASTENERS
C
E
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL INSERT
TOP/BOTTOM
PANEL
(11) (11)
11 11
CONNECTING (12) (12)
PLATE 12 12
(13) (13) 06
13 13 07
C C
NOTE:
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00911-A-002-01
CONF 002
(2) Task A320-A-25-XX-1BGK-02002-720A-A - Check Dimension of the Threaded
Pins of the Right Hand (RH) OHSC's
Job Set-Up Information
Working Area
Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 1 PIN (1)
11 NAS1149CN832R 2 WASHER (1)
12 MS21042-08 2 NUT (1)
13 FAS000033-000 1 PIN (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the RH OHSC’s, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, clean any remains of adhesive from
the inserts.
(e) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, got to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).
(h) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the length of the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, clean any remains of adhesive from the
inserts.
(l) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3 , View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(o) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the dimensions of all the new
Threaded Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the Inter-Bin Connecting Plates (ICPs) of the RH OHSC's, refer to Ref. Fig.
Additional Work of the LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work
of the LH and RH OHSC's SHEET 4, View E and Section C-C, do a check of the
dimensions of the Threaded Pins, Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
Task A320-A-25-XX-1BGK-02ZZZ-720Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 4, View E and Section C-C, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
CONF 002
Z260
Z250
Z240
Z230
B
C
D
A D
C
D E
C E
D C
E
C
D
D
C D
E FR43
E E D
C FR39
C
FR36
D
C FR30 D
D C
FR26 A 01 D
TYPICAL
C
D E
FR21 E
C
D D
E C
C
D D
E C
C
FR66
D D
E C FR63
D
C FR59
D
E C FR55
D B 01
FR47
TYPICAL
NOTE: FR43
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-0090Q-A-002-01
CONF 002
AFFECTED
FASTENERS
A
A
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
02
X-BRACKET BACK
PANEL
03
INSERT
(10)
10 (12)
12
(11)
11
A A BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090R-A-002-01
CONF 002
AFFECTED
FASTENERS
B
AFFECTED
FASTENERS
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
SIDEWALL INSERT
BOTTOM
PANEL
(11) (11)
11 11
Y-BRACKET
(12) (12)
12 12
(13) (13) 04
13 13 05
B B
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090S-A-002-01
CONF 002
AFFECTED
FASTENERS
AFFECTED
FASTENERS
C
E
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL INSERT
TOP/BOTTOM
PANEL
(11) (11)
11 11
CONNECTING (12) (12)
PLATE 12 12
(13) (13) 06
13 13 07
C C
NOTE:
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090T-A-002-01
CONF 003
(2) Task A320-A-25-XX-1BGK-02003-720A-A - Check Dimension of the Threaded
Pins of the Right Hand (RH) OHSC's
Job Set-Up Information
Working Area
Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 1 PIN (1)
11 NAS1149CN832R 2 WASHER (1)
12 MS21042-08 2 NUT (1)
13 FAS000033-000 1 PIN (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the RH OHSC’s, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, clean any remains of adhesive from
the inserts.
(e) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, got to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the length of the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, clean any remains of adhesive from the
inserts.
(l) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3 , View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to 2.2 and 2.8 Nm (19.47 and 24.78 lbf.in.).
(o) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the dimensions of all the new
Threaded Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the Inter-Bin Connecting Plates (ICPs) of the RH OHSC's, refer to Ref. Fig.
Additional Work of the LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work
of the LH and RH OHSC's SHEET 4, View E and Section C-C, do a check of the
dimensions of the Threaded Pins, Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
Task A320-A-25-XX-1BGK-02ZZZ-720Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 4, View E and Section C-C, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
CONF 003
Z260
Z250
Z240
Z230 C
B D
C
D
E
A C
D
E C
C
D D
E C FR43
C
D D
E C FR39
E E D
C
C FR34
D D
C C
FR30 A 01 D
D
FR26
TYPICAL C
D E
E
FR21
C
D
E
C
D D
E C
C
FR66
D D
E C FR63
C
D D
E C FR59
D
E C FR55
D
C B 01
FR51
D TYPICAL
FR47
NOTE: FR43
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-00912-A-002-01
CONF 003
AFFECTED
FASTENERS
A
A
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
02
X-BRACKET BACK
PANEL
03
INSERT
(10)
10 (12)
12
(11)
11
A A BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00913-A-002-01
CONF 003
AFFECTED
FASTENERS
B
AFFECTED
FASTENERS
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
SIDEWALL INSERT
BOTTOM
PANEL
(11) (11)
11 11
Y-BRACKET
(12) (12)
12 12
(13) (13) 04
13 13 05
B B
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00914-A-002-01
CONF 003
AFFECTED
FASTENERS
AFFECTED
FASTENERS
C
E
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL INSERT
TOP/BOTTOM
PANEL
(11) (11)
11 11
CONNECTING (12) (12)
PLATE 12 12
(13) (13) 06
13 13 07
C C
NOTE:
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-00915-A-002-01
CONF 004
(2) Task A320-A-25-XX-1BGK-02004-720A-A - Check Dimension of the Threaded
Pins of the Right Hand (RH) OHSC's
Job Set-Up Information
Working Area
Man-hours 1.50 h
Minimum Number of person 1
Elapsed Time 1.50h
Skills Cabin
Material necessary to do the job
Components
ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES
10 FAS000033-002 1 PIN (1)
11 NAS1149CN832R 2 WASHER (1)
12 MS21042-08 2 NUT (1)
13 FAS000033-000 1 PIN (1)
NOTE(S)
(1): The above list of components is not an AIRBUS Kit, the required parts shall be ordered
as necessary through the given channel.
Referenced Information
Manuals/Drawings References/Sheets
06-20-00, Page Block 001
AMM
06-31-53, Page Block 001
Procedure
(a) Standard Practices:
1 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.
2 For the Frame (FR) identification, refer to Ref. AMM 06-31-53, Page Block
001.
3 Tag all the parts you must remove and retain to make the subsequent
installation easier.
4 Put all the retained hardware in identified plastic bags and attach the bags
to the related unit.
(b) On the X-Brackets of the RH OHSC’s, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item (10):
1 If all the Threaded Pins, Item (10), are installed within tolerance, go to
work-step (i).
2 If any of the Threaded Pins, Item (10), are installed out of tolerance go to
the next work-step.
(c) From the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(d) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, clean any remains of adhesive from the inserts.
(e) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, got to work-step (f).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(f) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 10, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 10, must fully install
the pins into the inserts.
(g) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 2, View C and Section A-A, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(h) On the X-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the
LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 2, View C and Section A-A, do a check of the dimensions of all the
Threaded Pins, Item 10:
1 If all the new Threaded Pins, Item 10, are installed within tolerance, go to
work-step (i).
2 If any of the new Threaded Pins, Item 10, are installed out of tolerance,
repeat work-steps (c) thru (h).
(i) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the length of the Threaded Pins,
Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to
work-step (p).
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(j) From the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(k) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, clean any remains of adhesive from the
inserts.
(l) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (m).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(m) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(n) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3 , View D and Section B-B, install:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
1 Torque the Nuts, Item 12, to between 2.2 and 2.8 Nm (19.47 and 24.78
lbf.in.).
(o) On the Y-Brackets of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 3, View D and Section B-B, do a check of the dimensions of all the new
Threaded Pins, Item 13:
1 If all the new Threaded Pins, Item 13, are installed within tolerance, go to
work-step (p).
2 If any of the new Threaded Pins, Item 13, are installed out of tolerance,
repeat work-steps (j) thru (o).
(p) On the Inter-Bin Connecting Plates (ICPs) of the RH OHSC's, refer to Ref. Fig.
Additional Work of the LH and RH OHSC's SHEET 1 and Ref. Fig. Additional Work
of the LH and RH OHSC's SHEET 4, View E and Section C-C, do a check of the
dimensions of the Threaded Pins, Item (13):
1 If all the Threaded Pins, Item (13), are installed within tolerance, go to Ref.
Task A320-A-25-XX-1BGK-02ZZZ-720Z-A.
2 If any of the Threaded Pins, Item (13), are installed out of tolerance go to
the next work-step.
(q) From the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH
and RH OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's
SHEET 4, View E and Section C-C, carefully remove:
NOTE: The quantity of fasteners given above is the minimum required for
removal and can change depending on the inspection result.
(r) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, clean any remains of adhesive from the inserts.
(s) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, do a check of the inserts for damage:
1 If there is no damage to any of the inserts, go to work-step (t).
2 If there is damage to any of the inserts, contact AIRBUS and follow their
instructions.
(t) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
NOTE: The quantity of fasteners given above is the minimum required for
installation and can change depending on the inspection result.
1 Torque tighten the Threaded Pins, Item 13, to between 0.8 and 1.6 Nm
(7.08 and 14.16 lbf.in.).
NOTE: The final torque of the Threaded Pins, Item 13, must fully install
the pins into the inserts.
(u) On the ICPs of the RH OHSC's, refer to Ref. Fig. Additional Work of the LH and RH
OHSC's SHEET 1 and Ref. Fig. Additional Work of the LH and RH OHSC's SHEET 4,
View E and Section C-C, install:
CONF 004
Z260
Z250
C
Z240 D
C
Z230 D
B C E
D E
C
C E
A D D
C E C FR43
D D
C E C FR39
E
D D
C E FR35.7
D C FR35.5
E D
C FR35.3
C
E E D
C FR35.1 D D
C FR34 C
D D
C A 01
C E
FR30 TYPICAL D
D E
FR26 C
D D
C E C
FR21
D D
E C FR64
C E D
D C FR59
C
D
D FR55
C
E D FR51
C
D FR47.5
E C B 01
FR43
FR47.2
D TYPICAL
FR47
NOTE:
01 DIFFERENT DOOR TYPES OR LAVATORY POSITIONS WILL AFFECT THE POSITIONS OF THE
X-BRACKETS, Y-BRACKETS AND INTER-BIN CONNECTING PLATES.
ICN-A320-A-25XX1BGK-A-FAPE3-0090U-A-002-01
CONF 004
AFFECTED
FASTENERS
A
A
AFFECTED
FASTENERS
C
TYPICAL X-BRACKET
(6 FASTENERS MAX)
02
X-BRACKET BACK
PANEL
03
INSERT
(10)
10 (12)
12
(11)
11
A A BOTTOM
PANEL
NOTE:
02 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 10, MUST BE BETWEEN 12.70 mm (0.500 in) AND 16.00 mm (0.630 in).
03 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 10, MUST BE BETWEEN 1.60 mm (0.063 in) AND 4.80 mm (0.189 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090V-A-002-01
CONF 004
AFFECTED
FASTENERS
B
AFFECTED
FASTENERS
D
TYPICAL Y-BRACKET
(10 FASTENERS MAX)
SIDEWALL INSERT
BOTTOM
PANEL
(11) (11)
11 11
Y-BRACKET
(12) (12)
12 12
(13) (13) 04
13 13 05
B B
NOTE:
04 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 9.30 mm (0.366 in) AND 12.90 mm (0.508 in).
05 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 4.50 mm (0.177 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090W-A-002-01
CONF 004
AFFECTED
FASTENERS
AFFECTED
FASTENERS
C
E
TYPICAL
LOWER PLATE SHOWN
UPPER PLATE SIMILAR
SIDEWALL INSERT
TOP/BOTTOM
PANEL
(11) (11)
11 11
CONNECTING (12) (12)
PLATE 12 12
(13) (13) 06
13 13 07
C C
NOTE:
06 THE DISTANCE BETWEEN THE INSERT SURFACE AND THE END OF THE THREADED
PIN, ITEM 13, MUST BE BETWEEN 10.20 mm (0.402 in) AND 12.90 mm (0.508 in).
07 THE DISTANCE BETWEEN THE TOP OF THE NUT, ITEM 12, AND THE END OF THE
THREADED PIN, ITEM 13, MUST BE BETWEEN 0.90 mm (0.035 in) AND 3.60 mm (0.142 in).
ICN-A320-A-25XX1BGK-A-FAPE3-0090X-A-002-01
CONF ALL
D. PREPARATION FOR TEST
None
E. TEST
None
F. CLOSE-UP
(1) Task A320-A-25-XX-1BGK-01001-740A-A - Close-up
Job Set-Up Information
Manpower/Resources/Skills
Man-hours 8.00 h
Minimum Number of person 2
Elapsed Time 4.00h
Skills Airframe
Referenced Information
Manuals/Drawings References/Sheets
Task 25-23-48-400-001
AMM Task 25-24-41-400-001
Task 25-25-11-400-001
Procedure
(a) Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b) Install the cover panels, refer to Ref. AMM Task 25-24-41-400-001.
(c) Install the cove light panels, refer to Ref. AMM Task 25-23-48-400-001.
(d) Install the section hoses, refer to Ref. AMM Task 25-25-11-400-001.
(e) Put the aircraft back to its initial configuration.
G. ADMINISTRATIVE
(1) Task A320-A-25-XX-1BGK-01001-90AA-A - Administrative
Procedure
Confirm in the applicable aircraft records that you have completed all the work defined
in this Service Bulletin task set as required.
01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-25-1BGK
02
0 2 4 6 8 10 12 14
SB ELAPSED TIME
TOTAL MANHOURS 36.00 (HOURS)
SB ELAPSED TIME 13.00
NOTES:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
PER : NUMBER OF PERSONS ARE NOT REFLECTED IN THIS GANTT CHART.
ET/S: ELAPSED TIME PER STEP ICN-A320-A-25XX1BGK-A-FAPE3-000BJ-A-003-01
01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-25-1BGK
02
0 2 4 6 8 10 12 14
SB ELAPSED TIME
TOTAL MANHOURS 38.00 (HOURS)
SB ELAPSED TIME 13.50
NOTES:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
PER : NUMBER OF PERSONS ARE NOT REFLECTED IN THIS GANTT CHART.
ET/S: ELAPSED TIME PER STEP ICN-A320-A-25XX1BGK-A-FAPE3-000BK-A-003-01
01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-25-1BGK
02
0 2 4 6 8 10 12 14
SB ELAPSED TIME
TOTAL MANHOURS 42.00 (HOURS)
SB ELAPSED TIME 14.50
NOTES:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
PER : NUMBER OF PERSONS ARE NOT REFLECTED IN THIS GANTT CHART.
ET/S: ELAPSED TIME PER STEP ICN-A320-A-25XX1BGK-A-FAPE3-000BL-A-003-01
01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-25-1BGK
02
0 1 2 3 4 5 6 7 8 9
SB ELAPSED TIME
TOTAL MANHOURS 18.00 (HOURS)
SB ELAPSED TIME 9.00
NOTES:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
PER : NUMBER OF PERSONS ARE NOT REFLECTED IN THIS GANTT CHART.
ET/S: ELAPSED TIME PER STEP ICN-A320-A-25XX1BGK-A-FAPE3-00962-A-001-01
01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-25-1BGK
02
0 1 2 3 4 5 6 7 8 9
SB ELAPSED TIME
TOTAL MANHOURS 19.00 (HOURS)
SB ELAPSED TIME 9.50
NOTES:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
PER : NUMBER OF PERSONS ARE NOT REFLECTED IN THIS GANTT CHART.
ET/S: ELAPSED TIME PER STEP ICN-A320-A-25XX1BGK-A-FAPE3-00964-A-001-01
01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No A320-25-1BGK
02
0 1 2 3 4 5 6 7 8
SB ELAPSED TIME
TOTAL MANHOURS 17.50 (HOURS)
SB ELAPSED TIME 8.75
NOTES:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
PER : NUMBER OF PERSONS ARE NOT REFLECTED IN THIS GANTT CHART.
ET/S: ELAPSED TIME PER STEP ICN-A320-A-25XX1BGK-A-FAPE3-00963-A-001-01
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.
It is revised on a regular basis.
If you have difficulties in the accomplishment of this SB please quote below the area(s) and
give a short description of the issue.
Comments :
Operator : Date :
Name/Title
Please return this form to :
AIRBUS CUSTOMER SERVICES DIRECTORATE
Service Bulletins Management
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Fax: (+33) 5 61 93 42 51
Or via your Resident Customer Support Office.