s2Oa

25/2/87

NATIONAL STANDARDS COMMISSION

NATIONAL MEASUREMENT (PATTERNS OF INSTRUMENTS) REGULATIONS

REGULATION 9

SUPPLEMENTARY CERTIFICATE OF APPROVAL No S208

This is to certify thot on opprovol for use for trode hos been granted in respect
of the pottern of the

Yamato Model EDI-302 Digital Indicator

submitted by Yamato Scale (Australia)Pty Ltd

16 Gertrude Street
Arncliffe NSW 2205.

Conditions of Approvol
._
This opproval is subject to review on or after l/9/91.
This opprovol expires in respect of new instruments on l/9/92.

Instruments purportingto comply with this opprovol sholl be morked NSC No S208.

This approval moy be withdrown if instruments ore constructed other than OS

described in the drowirgs and specifications lodged with the Commission.

The number of scale intervals applicable to any weighing instrument in which this
indicator is used shall be no greater than the number of verification scale
intervals opproved for the basework, or the lood cell(s) or the indicator (80OOe)
whichever is the smallest,

Auxiliary devices used with this instrument shall comply with the requirements of
Generol Supplementary Certificates Nos Sl/O and/or S2/0, OS appropriate,

Signed

Executive Director

DescriptiveAdvice

Potterna approved 26/8/06

. Ycmmto model EDI-302 digital indicator.

Technic01 Schedule No S208 describes the pottern.

Filing Advice

The documentation for this approval comprises:

SupplementaryCertificateof Approval No S208 dated 2512187

Technic01 Schedule No S208 dated 25/2/87
Test Procedure No S208 dated 2512187
Figure 1 doted 25/2/87
 S208
25/2/87

NATIONAL STANDARDS COMMISSION

TECHNICAL SCHEDULE No S208

Potternr Yom&o Model EDI-302 Digitol Indicator

Submittor 1 Yomoto Stole (Auetrolio) Pty Ltd

16 Gertrude Street
Arncliffe NSW 2205.

1. Descriptionof Pottern

A digitol moss indicator (Figure 1) opproved for use with up to 8000 verification
stole intervols. The indicator moy be provided with output sockets for the
connection of ouxiliory and/or peripherol devices. (Note: The numeric keyboord
fitted to the instrument is inoperative.)

1 .I Zero

Zero is outomoticolly corrected to within 20.25e whenever the instrument comes to

rest within 0.5e of zero, If the instrument comes to rest outside thot ronge but
within the zero reset range, zero may be reset by pressing the zero button. The
zero light illumitmteswhenever zero is within LO.25e.

1.2 Tore

A semi-automaticsubtractive toring device of up to maximum copocity moy be fitted,

1.3 Totolisinq

The instrument may hove o memory function ollowing successive weighings to be

totolised.

1.4 Disploy Check

A display check is initiatedwhenever power is opplied to the instrument.

1.5 Marking

Instruments ore marked with the following doto, together in one location:

Manufacturer’s nome or mork

Accuracy class @
Serial number of instrument
Moximum copocity Mox ..*.... *
Minimum copocity Min . .. . ,. . *
Verificationstole interval e = d = ,.. +
Maximum subtractivetore T = - ,....
NSC opproval numbers - Indicator NSC No S208
- Other components (OS oppropriote)
Lood cell seriol number(s)

* These morkings ore repeoted in the vicinity of each reading face, if not olreody
in thot position,

The indicator shall olso be morked NOT FOR RETAIL COUNTER USE.

1.6 VesificotionMork

Provision is mode for Q verification mork to be applied.

 S208
25/2/ 87

NATIONAL STANDARDS COMMISSION

TEST PROCEDURE No S208

The following tests should be carried out in conjunction with any test procedures
in the approval documentation for the instrument to which this indicator is
connected.

All lood applications should be in accordonce with the Commission's recommended

testing procedure for the elimination of rounding error OS set out in Document 104,

The maximum permissible errors aret

LO.58 for loads between 0 and 5OOei

+l ,Oe for loads between 501e ond 2OOOe; ond
21.5e for loods obove 2OOOe.

1. Zero Test
._
As the outomotic device resets zero when the weighing mechanism is in equilibrium
within 0.5e of zero, zero should be checked as described in Document 104, with o
lood equal to, soy, 10e on the lood receptor. The indications with 0.258 ond 0.75e
odditionolmoss on the lood receptor will be 10e ond lle respectively.

2. Zero Range

The moximum ronge of operotion of the zero setting device should not exceed 4% of
the moximum copocfty (f 2% approximately). With zero bolonce indicated opply a
10d of, soy, 2.5% of maximum capacity to the instrument and press the zero button;
the instrument should not rezero.

3. Ronge of Indication

The moximum moss indicated should not exceed the morked moximum copocity by more
than 10e; obove this indicated moss the indication should be blonk or show
non-numerical chorocters.

Below zero the indicationshould blank or show o moss preceded by o minus sign.

4. Lood Test

Test loods ore to be applied to the complete weighing instrument increasing in not
- less thon 5 opproximotely equal steps to moximum capacity, followed by decreasing
loods in not less than 5 approximatelyequol steps to zero lood.

5. Tore Test

The semi-outomotic taring device (where fitted) sholl be oble to reset the moss
indicator to zero within $0.25e at any load within its capacity: . this moy be
checked OS described for Zero Test. .

A tore sholl not be oble to be acquired obove the moximun tore ronge morked on the
instrument.
 S2UB
25/2/07
~