Diesel generator set X2.5 series engine 15 kVA–27 kVA 50 Hz 10.8 kW–20 kW 60 Hz
Description This Cummins® Power Generation Cooling system – Standard integral set- commercial generator set is a fully integrated mounted radiator system, designed and tested power generation system, providing optimum for rated ambient temperatures, simplifies facility performance, reliability, and versatility design requirements for rejected heat. for stationary standby, prime power, and continuous duty applications. Control system – PowerStart control, microprocessor-based generator set monitoring and control system provides a simple operator Features interface to the generator set, manual and Cummins® heavy-duty engine – Rugged remote start/stop control and shutdown fault 4-cycle industrial diesel delivers reliable indication. power, low emissions and fast response to load changes. Enclosures – Optional weather-protective and sound-attenuated enclosure. Optional excitation boost system (EBS) – Offers enhanced motor starting and Warranty – Backed by a comprehensive fault clearing short circuit capability. warranty and Worldwide distributor network.
Alternator – Several alternator sizes offer
selectable motor starting capability with low reactance 2/3 pitch windings; low waveform distortion with non-linear loads and fault clearing short-circuits capability.
Engine specifications Design 4 cycle, in-line, naturally aspirated Bore 91.7 mm Stroke 127 mm Displacement 2.5 liter (153 in3) Cylinder block Alloy cast iron, in-line, 3 cylinder Battery charging alternator 36 A Starting voltage 12 volt, negative ground Fuel system Direct injection Fuel filter Spin on fuel filters with water separator Air cleaner type Dry replaceable element Lube oil filter type(s) Spin on full flow filter, filtration efficiency 25 micron 99% (min) Standard cooling system 122 °F (50 °C) ambient radiator with coolant recovery system
Alternator specifications Design Brushless, single bearing Stator 2/3 pitch Insulation system Class H Standard temperature rise 125–163 °C Exciter type Self excited Phase rotation A (U), B (V), C (W) Alternator cooling Direct drive centrifugal blower fan AC waveform total harmonic distortion (THDV) No load to full linear load < 5%. For any single harmonic < 3% Telephone influence factor (TIF) < 50 per NEMA MG1-22.43 Telephone harmonic factor (THF) < 3%
Engine Enclosure Control panel 500 litre fuel tank Electronic engine governing Optional silent power PowerCommand 1.1 Warranty Coolant heater 120/240 V canopy 2/4 pole main circuit 5 years for standby Alternator breaker application Cooling Antifreeze 50/50 (ethylene Alternator heater Base frame 2 years for prime glycol) Excite boost system (EBS) Dual skin fully contained application fuel tank Note: Some options may not be available on all models - consult factory for availability.
Applicable for supplying power to varying electrical
C load for the duration of power interruption of a reliable utility source. Emergency standby power (ESP) is in accordance with ISO 8528. Fuel stop power in accordance with ISO 3046, AS 2789, DIN 6271 and A B BS 5514.
Limited-time running power (LTP):
ENCLOSED Applicable for supplying power to a constant electrical load for limited hours. Limited time running power (LTP) is in accordance with ISO 8528.
C Prime power (PRP): Applicable for supplying power to varying electrical load for unlimited hours. Prime power (PRP) is in A B accordance with ISO 8528. Ten percent overload capability is available in accordance with ISO 3046, AS 2789, DIN 6271 and BS 5514. This outline drawing is to provide representative configuration details for Model series only. Base load (continuous) power (COP): See respective model data sheet for specific model outline Applicable for supplying power continuously to drawing number. a constant electrical load for unlimited hours. Continuous power (COP) in accordance with ISO 8528, ISO 3046, AS 2789, DIN 6271 and BS 5514. Do not use for installation design
Weight and dimensions
Open Enclosed A B C Dry wt.* Wet wt.* A B C Dry wt.* Wet wt.* Model mm mm mm (kg) (kg) mm mm mm (kg) (kg) C17 D5 1667 930 1247 418.5 582 2082 930 1448 743.5 907 C22 D5 1667 930 1247 418.5 582 2082 930 1448 743.5 907 C28 D5 1667 930 1247 441.5 605 2082 930 1448 766.5 930 C12 D6 1667 930 1247 405 568.5 2082 930 1448 730 893.5 C16 D6 1667 930 1247 405 568.5 2082 930 1448 730 893.5 C20 D6 1667 930 1247 418.5 582 2082 930 1448 743.5 907 *Note: Weights represent a set with standard features. See outline drawings for weights of other configurations.
Certifications This generator set is designed in facilities This generator set is available with certified to ISO 9001 and manufactured in CE certification. facilities certified to ISO 9001 or ISO 9002.
The Prototype Test Support (PTS) program verifies the
performance integrity of the generator set design. Cummins Power Generation products bearing the PTS symbol meet the prototype test requirements of NFPA 110 for Level 1 systems.
Cummins Power Generation
Americas Asia Pacific Europe, CIS, Middle East and Africa
Cummins Power Generation and Cummins are registered trademarks of Cummins Inc. PowerCommand, AmpSentry, InPower and “Our energy working for you.” are trademarks of Cummins Power Generation. Other company, product, or service names may be trademarks or service marks of others. Specifications are subject to change without notice. cumminspower.com SS26-CPGK-RevA (05/12)
