B650 EAGLE AX

B650 UD AC

User's Manual
Rev. 1002

GIGABYTE will reduce paper use in order to fulfill the responsibilities of a global citizen.
Also, to reduce the impacts on global warming, the packaging materials of this product
are recyclable and reusable. GIGABYTE works with you to protect the environment.
For more product details, please visit GIGABYTE's website.
Copyright
© 2024 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without
prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
„„ For detailed product information, carefully read the User's Manual.
„„ For quick set-up of the product, refer to the Quick Installation Guide on GIGABYTE's
website.
https://download.gigabyte.com/FileList/Manual/mb_manual_quick-guide_am5.pdf?m=sw

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"
means the revision of the motherboard is 1.0. Check your motherboard revision before updating
motherboard BIOS, drivers, or when looking for technical information.

Example:
 Table of Contents
Chapter 1 Product Introduction........................................................................................4
1-1 Motherboard Layout.......................................................................................... 4
1-2 Box Contents..................................................................................................... 6

Chapter 2 Hardware Installation......................................................................................7

2-1 Installation Precautions..................................................................................... 7
2-2 Product Specifications....................................................................................... 8
2-3 Installing the CPU and CPU Cooler................................................................ 12
2-4 Installing the Memory...................................................................................... 15
2-5 Installing an Expansion Card.......................................................................... 16
2-6 Back Panel Connectors................................................................................... 17
2-7 Onboard Button and LEDs.............................................................................. 19
2-8 Internal Connectors......................................................................................... 20

Chapter 3 BIOS Setup...................................................................................................31

Chapter 4 Installing the Operating System and Drivers.................................................33

4-1 Operating System Installation......................................................................... 33
4-2 Drivers Installation........................................................................................... 34

Chapter 5 Appendix.......................................................................................................35
5-1 Configuring a RAID Set................................................................................... 35

Regulatory Notices..................................................................................................... 36
Contact Us................................................................................................................. 39

-3-
Chapter 1 Product Introduction
1-1 Motherboard Layout

SYS_FAN1

CPU_OPT LED_C
ATX_12V CPU_FAN
DP_HDMI ARGB_V2_2

KB_MS_USB SOCKET AM5

USB 2.0 Hub

ATX
USB20

M2_WIFI

B650 EAGLE AX
U32C
U32G2

SYS_FAN3_PUMP
USB_LAN

AUDIO

F_U32
110 80
M2A_CPU

F_U32C
DDR5_A1

DDR5_A2
DDR5_B1
DDR5_B2

Realtek®
GbE LAN PCIEX16

110 80
M2P_CPU

AMD
Chipset
110 80
2 0
SATA3 3 1
M2C_SB

PCIEX1_1
CODEC

M_BIOS
PCIEX1_2
iTE®
Super I/O
BAT
PCIEX1_3
USB 2.0 Hub
BOOT DRAM

CLR_CMOS
VGA CPU

F_AUDIO SPI_TPM QFLED

ARGB_V2_3

ARGB_V2_1 SYS_FAN2 F_USB3 F_USB1

COM ESPI_DB QFLASH_PLUS F_USB2 F_PANEL

Temperature sensor

-4-
 SYS_FAN1

CPU_OPT LED_C
ATX_12V CPU_FAN
DP_HDMI

KB_MS_USB SOCKET AM5

USB 2.0 Hub

ATX
USB20

M2_WIFI

B650 UD AC
U32C
U32G2

SYS_FAN3_PUMP
USB_LAN

AUDIO

F_U32
110 80
M2A_CPU

F_U32C
DDR5_A1

DDR5_A2
DDR5_B1
DDR5_B2

Realtek®
GbE LAN PCIEX16

110 80
M2P_CPU

AMD
Chipset
110 80
2 0
SATA3 3 1
M2C_SB

PCIEX1_1
CODEC

M_BIOS
PCIEX1_2
iTE®
Super I/O
BAT
PCIEX1_3
USB 2.0 Hub
CLR_CMOS
F_AUDIO SPI_TPM QFLED
ARGB_V2_3

SYS_FAN2 F_USB3 F_USB1

ESPI_DB QFLASH_PLUS F_USB2 F_PANEL

Temperature sensor

-5-
1-2 Box Contents

55 B650 EAGLE AX or B650 UD AC motherboard

55 User's Manual
55 Two antennas
55 I/O Shield k
55 Two SATA cables
55 M.2 screw

* The box contents above are for reference only and the actual items shall depend on the product package you obtain.
The box contents are subject to change without notice.

k Only for B650 UD AC.

-6-
Chapter 2 Hardware Installation
2-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's
manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,
keep your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
•• Before connecting or unplugging the power supply cable from the motherboard, make sure
the power supply has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware
components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature or wet environment.
•• Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
•• If you use an adapter, extension power cable, or power strip, ensure to consult with its installation
and/or grounding instructions.

-7-
2-2 Product Specifications
CPU ŠŠ AMD Socket AM5, support for:
AMD Ryzen™ 7000 Series Processors/
AMD Ryzen™ 8000 Series Processors
(Go to GIGABYTE's website for the latest CPU support list.)
Chipset ŠŠ AMD B650
Memory ŠŠ Support for DDR5 5200/4800/4400 MT/s memory modules
ŠŠ 4 x DDR5 DIMM sockets supporting up to 192 GB (48 GB single DIMM capacity)
of system memory
ŠŠ Dual channel memory architecture
ŠŠ Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules
ŠŠ Support for AMD EXtended Profiles for Overclocking (AMD EXPO™) and Extreme
Memory Profile (XMP) memory modules
(The CPU and memory configuration may affect the supported memory types, data
rate (speed), and number of DRAM modules, please refer to "Memory Support
List" on GIGABYTE's website for more information.)
Onboard ŠŠ Integrated Graphics Processor:
Graphics - 1 x DisplayPort, supporting a maximum resolution of 3840x2160@144 Hz
* Support for DisplayPort 1.4 version.
- 1 x HDMI port, supporting a maximum resolution of 4096x2160@60 Hz
* Support for HDMI 2.1 version and HDCP 2.3.
** Support for native HDMI 2.1 TMDS compatible ports.
(Graphics specifications may vary depending on CPU support.)
Audio ŠŠ Realtek® Audio CODEC
ŠŠ High Definition Audio
ŠŠ 2/4/5.1/7.1-channel
* You can change the functionality of an audio jack using the audio software. To
configure 7.1-channel audio, access the audio software for audio settings.

LAN ŠŠ Realtek® GbE LAN chip (1 Gbps/100 Mbps/10 Mbps)

Wireless ŠŠ Realtek® Wi-Fi 6E RTL8852CE
Communication - WIFI a, b, g, n, ac, ax, supporting 2.4/5/6 GHz carrier frequency bands
Module j - BLUETOOTH 5.3
- Support for 11ax 160MHz wireless standard
(Actual data rate may vary depending on environment and equipment.)
Wireless ŠŠ AzureWave Wi-Fi AW-CB304NF/AW-CB515NF (Realtek® RTL8821CE)
Communication - WIFI 802.11a, b, g, n, ac, supporting 2.4/5 GHz Dual-Band
Module k - BLUETOOTH 5.0
- Support for 11ac wireless standard
(Actual data rate may vary depending on environment and equipment.)

j Only for B650 EAGLE AX.

k Only for B650 UD AC.
-8-
Expansion Slots ŠŠ 1 x PCI Express x16 slot (PCIEX16), integrated in the CPU:
 AMD Ryzen™ 7000 Series Processors support PCIe 4.0 x16 mode
 AMD Ryzen™ 8000 Series-Phoenix 1 Processors support PCIe 4.0 x8 mode
 AMD Ryzen™ 8000 Series-Phoenix 2 Processors support PCIe 4.0 x4 mode
* The PCIEX16 slot can only support a graphics card or an NVMe SSD. If only one
graphics card is to be installed, be sure to install it in the PCIEX16 slot.
ŠŠ Chipset:
- 3 x PCI Express x16 slots, supporting PCIe 3.0 and running at x1
* The PCIEX1_1 and PCIEX1_2 slots become unavailable when an AMD Ryzen™ 8000
Series-Phoenix 2 processor is used.
Storage Interface ŠŠ 1 x M.2 connector (M2A_CPU), integrated in the CPU, supporting Socket 3,
M key, type 25110/2580 SSDs:
 AMD Ryzen™ 7000 Series Processors support PCIe 5.0 x4/x2 SSDs
 AMD Ryzen™ 8000 Series-Phoenix 1 Processors support PCIe 4.0 x4/x2 SSDs
 AMD Ryzen™ 8000 Series-Phoenix 2 Processors support PCIe 4.0 x4/x2 SSDs
ŠŠ 1 x M.2 connector (M2P_CPU), integrated in the CPU, supporting Socket 3,
M key, type 22110/2280 SSDs:
 AMD Ryzen™ 7000 Series Processors support PCIe 4.0 x2 SSDs
 AMD Ryzen™ 8000 Series-Phoenix 1 Processors support PCIe 4.0 x2 SSDs
 AMD Ryzen™ 8000 Series-Phoenix 2 Processors support PCIe 4.0 x2 SSDs
ŠŠ Chipset:
- 1 x M.2 connector (Socket 3, M key, type 22110/2280 PCIe 4.0 x4/x2
SSD support) (M2C_SB)
ŠŠ 4 x SATA 6Gb/s connectors
ŠŠ RAID 0, RAID 1, and RAID 10 support for NVMe SSD storage devices
ŠŠ RAID 0, RAID 1, and RAID 10 support for SATA storage devices
USB ŠŠ CPU:
- 2 x USB 3.2 Gen 2 Type-A ports (red) on the back panel
- 1 x USB Type-C® port on the back panel, with USB 3.2 Gen 1 support
ŠŠ CPU+USB 2.0 Hub:
- 4 x USB 2.0/1.1 ports on the back panel
ŠŠ Chipset:
- 2 x USB 3.2 Gen 1 ports available through the internal USB header
- 1 x USB Type-C ® port with USB 3.2 Gen 1 support, available through the
internal USB header
- 4 x USB 2.0/1.1 ports (2 ports on the back panel, 2 ports available through
the internal USB header)
ŠŠ Chipset+USB 2.0 Hub:
- 4 x USB 2.0/1.1 ports available through the internal USB headers

-9-
 Internal ŠŠ 1 x 24-pin ATX main power connector
Connectors ŠŠ 1 x 8-pin ATX 12V power connector
ŠŠ 1 x CPU fan header
ŠŠ 1 x CPU fan/water cooling pump header
ŠŠ 2 x system fan headers
ŠŠ 1 x system fan/water cooling pump header
ŠŠ 3 x addressable RGB Gen2 LED strip headers j
ŠŠ 1 x addressable RGB Gen2 LED strip header k
ŠŠ 1 x RGB LED strip header
ŠŠ 3 x M.2 Socket 3 connectors
ŠŠ 4 x SATA 6Gb/s connectors
ŠŠ 1 x front panel header
ŠŠ 1 x front panel audio header
ŠŠ 1 x USB Type-C® header, with USB 3.2 Gen 1 support
ŠŠ 1 x USB 3.2 Gen 1 header
ŠŠ 3 x USB 2.0/1.1 headers
ŠŠ 1 x Trusted Platform Module header (For the GC-TPM2.0 SPI/GC-TPM2.0 SPI 2.0/
GC-TPM2.0 SPI V2 module only)
ŠŠ 1 x Q-Flash Plus button
ŠŠ 1 x serial port header j
ŠŠ 1 x Clear CMOS jumper
Back Panel ŠŠ 1 x DisplayPort
Connectors ŠŠ 1 x HDMI port
ŠŠ 1 x PS/2 keyboard/mouse port
ŠŠ 2 x SMA antenna connectors (2T2R) j
ŠŠ 2 x SMA antenna connectors (1T1R) k
ŠŠ 1 x USB Type-C® port, with USB 3.2 Gen 1 support
ŠŠ 2 x USB 3.2 Gen 2 Type-A ports (red)
ŠŠ 6 x USB 2.0/1.1 ports
ŠŠ 1 x RJ-45 port
ŠŠ 3 x audio jacks
I/O Controller ŠŠ iTE® I/O Controller Chip
Hardware ŠŠ Voltage detection
Monitor ŠŠ Temperature detection
ŠŠ Fan speed detection
ŠŠ Water cooling flow rate detection
ŠŠ Fan fail warning
ŠŠ Fan speed control
* Whether the fan (pump) speed control function is supported will depend on the fan
(pump) you install.

j Only for B650 EAGLE AX.

k Only for B650 UD AC.
- 10 -
 BIOS ŠŠ 1 x 256 Mbit flash
ŠŠ Use of licensed AMI UEFI BIOS
ŠŠ PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0
Unique Features ŠŠ Support for GIGABYTE Control Center (GCC)
* Available applications in GCC may vary by motherboard model. Supported functions
of each application may also vary depending on motherboard specifications.
ŠŠ Support for Q-Flash
ŠŠ Support for Q-Flash Plus
Bundled ŠŠ Norton® Internet Security (OEM version)
Software ŠŠ LAN bandwidth management software
Operating ŠŠ Support for Windows 11 64-bit
System ŠŠ Support for Windows 10 64-bit
Form Factor ŠŠ ATX Form Factor; 30.5cm x 24.4cm

* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without
prior notice.

&& Please visit the SERVICE/SUPPORT\Utility page on GIGABYTE's website to download the latest version
of apps.
https://www.gigabyte.com/Support/Utility/Motherboard?m=ut

- 11 -
2-3 Installing the CPU and CPU Cooler
Read the following guidelines before you begin to install the CPU:
•• Make sure that the motherboard supports the CPU.
(Go to GIGABYTE's website for the latest CPU support list.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage.
•• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
•• Apply an even and thin layer of thermal grease on the surface of the CPU.
•• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur.
•• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specifications, please do so according to your hardware specifications including the CPU, graphics
card, memory, hard drive, etc.

A. Note the CPU Orientation

Note the alignment keys on the motherboard CPU socket and the notches on the CPU.

Alignment Key

Triangle Pin One

Marking of the
CPU Socket

AM5 CPU Socket

Alignment Key

Notch

Triangle Pin One

Marking on the
CPU
AM5 CPU

Notch

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load
plate automatically after you insert the CPU and close the load plate.

&& Please visit GIGABYTE's website for details on hardware installation.

https://www.gigabyte.com/WebPage/210/quick-guide.html?m=sw

- 12 -
B. Installing the CPU
Follow the steps below to correctly install the CPU into the motherboard CPU socket.

u l
Gently press the CPU socket lever handle
j
down and away from the socket.
Completely lift up the CPU socket lock-
k
ing lever.
With your fingers, hold the plastic protec-
l
tive cover attached to the metal load plate
to lift open the metal load plate. k

Pin One

v
Hold the CPU with your fingers by the edges.
Align the CPU pin one marking (triangle) with
the pin one corner of the CPU socket (or you
may align the CPU notches with the socket
alignment keys) and gently insert the CPU
into position.

w l
Make sure the CPU is properly installed and
then close the load plate. Secure the socket j
lever under its retention tab. The plastic
protective cover will pop off by itself and can
be removed.
* Always replace the plastic protective cover
when the CPU is not installed to protect the
CPU socket. k

Do not force to engage the CPU socket locking lever when the CPU is not installed correctly
as this would damage the CPU and CPU socket.

- 13 -
C. Installing the CPU Cooler
Be sure to install the CPU cooler after installing the CPU. (Actual installation process may differ depending the
CPU cooler to be used. Refer to the user's manual for your CPU cooler.)

u
Apply an even and thin layer of thermal
grease on the surface of the installed CPU.

v Type A

Type A:
Hook the CPU cooler clip to the mounting
lug on one side of the retention frame. On
the other side, push straight down on the k
CPU cooler clip to hook it to the mounting
lug on the retention frame. Turn the cam
handle from the left side to the right side to
lock into place.
Type B: j
First remove the four screws from the CPU
retention frame and remove the CPU reten-
tion frame. Then align the four shoulder j
v l
screws on the CPU cooler with the standoffs
Type B
from the back plate. Fasten each shoulder
screw in a 1-2-3-4 (x) pattern as shown
on the right. m
u
4 1
k
2 3
* When using a Type B CPU cooler, it is not
recommended to fasten each screw down all the
way in one step. Follow order 1-2-3-4, fasten screw
clockwise 1 rotation per step. Repeat steps 1-2-3-4
till all screws are fastened.

4 1 4 1

w 2 3 2 3

Finally, attach the power connector of

the CPU cooler to the CPU fan header
(CPU_FAN) on the motherboard.

4 1
CPU_FAN 4 1

2 3
2 3

- 14 -
2-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
•• Make sure that the motherboard supports the memory. It is recommended that memory of the same
capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest supported
memory speeds and memory modules.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the
memory to prevent hardware damage.
•• Memory modules have a foolproof design. A memory module can be installed in only one direction.
If you are unable to insert the memory, switch the direction.
•• When installing memory modules, be sure to install in the DDR5_A2 socket first.

* Recommended Memory Configurations:

DDR5_A1 DDR5_A2 DDR5_B1 DDR5_B2
1 Module -- a -- --
2 Modules* -- a -- a
4 Modules* a a a a
("a"=Installed, "- -"=No Memory)
("*"=Recommended Dual Channel Memory Configurations)

DDR5_A1
DDR5_A2
DDR5_B1
DDR5_B2

Dual Channel Memory Configuration

This motherboard provides four memory sockets and supports Dual Channel Technology. After the memory
is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual
Channel memory mode will double the original memory bandwidth.
The four memory sockets are divided into two channels and each channel has two memory sockets as following:

Channel A: DDR5_A1, DDR5_A2

Channel B: DDR5_B1, DDR5_B2

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1. Dual Channel mode cannot be enabled if only one memory module is installed.
2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of
the same capacity, brand, speed, and chips be used.

- 15 -
2-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
•• Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card.
•• Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage.

Follow the steps below to correctly install your expansion card in the expansion slot.
1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.
2. Align the card with the slot, and press down on the card until it is fully seated in the slot.
3. Make sure that the expansion card is fully seated in its slot.
4. Secure the card's metal bracket to the chassis back panel with a screw.
5. After installing all expansion cards, replace the chassis cover(s).
6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your
expansion card(s).
7. Install the driver provided with the expansion card in your operating system.

PCIEX16 Slot

- 16 -
2-6 Back Panel Connectors

DisplayPort
DisplayPort delivers high quality digital imaging and audio, supporting bi-directional audio transmission.
DisplayPort can support the HDCP 2.3 content protection mechanism. You can use this port to connect
your DisplayPort-supported monitor. Note: The DisplayPort Technology can support a maximum resolution
of 3840x2160@144 Hz but the actual resolutions supported depend on the monitor being used.
HDMI Port
The HDMI port is HDCP 2.3 compliant and supports Dolby TrueHD and DTS
HD Master Audio formats. It also supports up to 192KHz/24bit 7.1-channel
LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum
supported resolution is 4096x2160@60 Hz, but the actual resolutions supported are dependent on the
monitor being used.
After installing the DisplayPort/HDMI device, make sure to set the default sound playback device
to DisplayPort/HDMI. (The item name may differ depending on your operating system.)

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
SMA Antenna Connectors (2T2Rj/1T1Rk)
Use this connector to connect an antenna.
Tighten the antennas to the antenna connectors and then aim the antennas correctly for better
signal reception.
USB 3.2 Gen 2 Type-A Port (Red)
The USB 3.2 Gen 2 port supports the USB 3.2 Gen 2 specification and is compatible to the USB 3.2 Gen 1
and USB 2.0 specification. Use this port for USB devices.
USB 3.2 Gen 2 Type-A Port (Red) (Q-Flash Plus Port)
The USB 3.2 Gen 2 port supports the USB 3.2 Gen 2 specification and is compatible to the USB 3.2 Gen 1
and USB 2.0 specification. Use this port for USB devices. Before using Q-Flash Plus (Note), make sure to
insert the USB flash drive into this port first.
USB Type-C® Port (with USB 3.2 Gen 1 Support)
The reversible USB port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0
specification. Use this port for USB devices.

j Only for B650 EAGLE AX.

k Only for B650 UD AC.
(Note) To enable the Q-Flash Plus function, please navigate to the "Unique Features" page of GIGABYTE's
website for more information.
- 17 -
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
Speed LED Activity LED Speed LED: Activity LED:
State Description State Description
Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring
Green 100 Mbps data rate Off No data transmission or receiving is occurring
LAN Port Off 10 Mbps data rate

Line In/Rear Speaker Out (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out/Front Speaker Out (Green)
The line out jack.
Mic In/Center/Subwoofer Speaker Out (Pink)
The Mic in jack.

Audio Jack Configurations:

Headphone/
Jack 4-channel 5.1-channel 7.1-channel
2-channel
Line In/Rear Speaker Out a a a
Line Out/Front Speaker Out a a a a
Mic In/Center/Subwoofer Speaker Out a a
Front Panel Line Out/Side Speaker Out a

You can change the functionality of an audio jack using the audio software. To configure
7.1-channel audio, access the audio software for audio settings.

&& Please visit GIGABYTE's website for details on configuring the audio software.
https://www.gigabyte.com/WebPage/697/realtek897-audio.html

•• When removing the cable connected to a back panel connector, first remove the cable from your
device and then remove it from the motherboard.
•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.

- 18 -
2-7 Onboard Button and LEDs
QFLASH_PLUS (Q-Flash Plus Button)
Q-Flash Plus allows you to update the BIOS when your system is off (S5 shutdown state). Save the latest BIOS
on a USB thumb drive and plug it into the dedicated port, and then you can now flash the BIOS automatically by
simply pressing the Q-Flash Plus button. The QFLED will flash when the BIOS matching and flashing activities
start and will stop flashing when the main BIOS flashing is complete.

QFLED

QFLASH_PLUS

To enable the Q-Flash Plus function, please navigate to the "Unique Features" page of GIGABYTE's
website for more information.

Status LEDs j
The status LEDs show whether the CPU, memory, graphics card, and operating system are working properly
after system power-on. If the CPU/DRAM/VGA LED is on, that means the corresponding device is not working
normally; if the BOOT LED is on, that means you haven't entered the operating system yet.

CPU: CPU status LED

DRAM: Memory status LED
VGA: Graphics card status LED
BOOT: Operating system status LED

CPU DRAM
VGA BOOT

j Only for B650 EAGLE AX.

- 19 -
2-8 Internal Connectors

1 6 3 4

7
8j

14

5
10 13

10
9
10

18
19
12
16j
8 8j 17 4 15 11

1) ATX_12V 11) F_PANEL

2) ATX 12) F_AUDIO
3) CPU_FAN 13) F_U32C
4) SYS_FAN1/2 14) F_U32
5) SYS_FAN3_PUMP 15) F_USB1/F_USB2/F_USB3
6) CPU_OPT 16) COMj
7) LED_C 17) SPI_TPM
8) ARGB_V2_1j/ARGB_V2_2j/ARGB_V2_3 18) BAT
9) SATA3 0/1/2/3 19) CLR_CMOS
10) M2A_CPU/M2P_CPU/M2C_SB

Read the following guidelines before connecting external devices:

•• First make sure your devices are compliant with the connectors you wish to connect.
•• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
•• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
j Only for B650 EAGLE AX.

- 20 -
1/2) ATX_12V/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components
on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and
all devices are properly installed. The power connector possesses a foolproof design. Connect the power
supply cable to the power connector in the correct orientation.
The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,
the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide
the required power, the result can lead to an unstable or unbootable system.

ATX_12V:
Pin No. Definition Pin No. Definition
5 8 1 GND (Only for 2x4-pin 12V) 5 +12V (Only for 2x4-pin 12V)
1 4 2 GND (Only for 2x4-pin 12V) 6 +12V (Only for 2x4-pin 12V)
ATX_12V 3 GND 7 +12V
4 GND 8 +12V

ATX:
12 24
Pin No. Definition Pin No. Definition
1 3.3V 13 3.3V
2 3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON (soft On/Off)
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 NC
9 5VSB (stand by +5V) 21 +5V
10 +12V 22 +5V
11 +12V (Only for 2x12-pin 23 +5V (Only for 2x12-pin ATX)
1 13 ATX)
12 3.3V (Only for 2x12-pin ATX) 24 GND (Only for 2x12-pin ATX)
ATX

- 21 -
3/4) CPU_FAN/SYS_FAN1/2 (Fan Headers)
All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.
When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is
the ground wire). The speed control function requires the use of a fan with fan speed control design. For
optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

1
Pin No. Definition
CPU_FAN/SYS_FAN1 1 GND
2 Voltage Speed Control
3 Sense
1 4 PWM Speed Control

SYS_FAN2

5) SYS_FAN3_PUMP (System Fan/Water Cooling Pump Header)

The fan/pump header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a
foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation
(the black connector wire is the ground wire). The speed control function requires the use of a fan with
fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed
inside the chassis. The header also provides speed control for a water cooling pump. Please navigate to
the "BIOS Setup" page of GIGABYTE's website and search for "Smart Fan 6" for more information.

Pin No. Definition

1 GND
1 2 Voltage Speed Control
3 Sense
4 PWM Speed Control

•• Be sure to connect fan cables to the fan headers to prevent your CPU and system from
overheating. Overheating may result in damage to the CPU or the system may hang.
•• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.

- 22 -
6) CPU_OPT (CPU Fan/Water Cooling Pump Header)
The fan/pump header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a
foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation
(the black connector wire is the ground wire). The speed control function requires the use of a fan with fan
speed control design.

Pin No. Definition

1 GND
1 2 Voltage Speed Control
3 Sense
4 PWM Speed Control

Connector CPU_FAN SYS_FAN1/2 SYS_FAN3_PUMP CPU_OPT

Maximum Current 2A 2A 2A 2A

Maximum Power 24W 24W 24W 24W

7) LED_C (RGB LED Strip Header)

The header can be used to connect a standard 5050 RGB LED strip (12V/G/R/B), with maximum power
rating of 2A (12V) and maximum length of 2m.
DEBUG
PORT

Pin No. Definition

1 12V
1 2 G
3 R
4 B

RGB LED Strip

Connect your RGB LED strip to the header. The power pin (marked
with a triangle on the plug) of the LED strip must be connected to Pin 1
1
(12V) of this header. Incorrect connection may lead to the damage 12V
of the LED strip.

For how to turn on/off the lights of the LED strip, please navigate to the "Unique Features" page
of GIGABYTE's website.
Before installing or removing the devices, be sure to turn off the devices and your computer. Unplug
the power cord from the power outlet to prevent damage to the devices.

- 23 -
 B3

_
B

_3

_B
_
F_

S F_
S S_F
8) ARGB_V2_1j/ARGB_V2_2j/ARGB_V2_3 (Addressable RGB Gen2 LED Strip Headers)
F_USB30 3
The headers can be used to connect a standard 5050 addressable RGB Gen2 LED strip, with maximum

B_

_
power rating of 3A (5V) and maximum number of 256 LEDs.

F
F_

_
1 Pin No. Definition

S _
ARGB_V2_2j 1 V (5V)
2 Data
S _

1 3 No Pin
ARGB_V2_1j/ARGB_V2_3 4 GND
F_USB3 F

F_
_

F_USB30 3
B_
_

Addressable RGB Gen2

Connect your addressable RGB Gen2 LED strip to the header. The power pin

S S_F
LED Strip

(marked with a triangle on the plug) of the LED strip must be connected to
S F_

Pin 1 of the addressable RGB Gen2 LED strip header. Incorrect connection

F_
1

_
_B

may lead to the damage of the LED strip.

_3

F_USB3
_

_0
For how to turn on/off the lights of the LED strip, please navigate to the "Unique Features" page

_ F

_0
of GIGABYTE's website.
U

F
•• To avoid abnormal LED behavior, do not connect addressable RGB Gen1 LED strips and
addressable RGB Gen2 LED strips to the same header at the same time.
•• Before installing or removing the devices, be sure to turn off the devices and your computer.
Unplug the power cord from the power outlet to prevent damage to the devices.

9) SATA3 0/1/2/3 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

B_
1.5Gb/s standard. Each SATA connector supports a single SATA device. The SATA connectors support
_
_

RAID 0, RAID 1, and RAID 10. Please navigate to the "Configuring a RAID Set" page of GIGABYTE's
_

website for instructions on configuring a RAID array.

USB 0_ B
G.QBOFM G.QBOFM

Pin No. Definition

_S

1 GND
S

7 1
2 TXP
S F

7 1
3 TXN
4 GND
2 0 5 RXN
B_

SATA3
3 1
6 RXP
7 GND

To enable hot-plugging for the SATA ports, please navigate to the "BIOS Setup" page of
B_

GIGABYTE's website and search for "SATA Configuration" for more information.

j Only for B650 EAGLE AX.

- 24 -
_
_

U
S
S

S
 _3 U

10) M2A_CPU/M2P_CPU/M2C_SB
_3 (M.2 USocket 3 Connectors)
There are two types of M.2 SSDs: M.2 SATA SSDs and M.2 PCIe SSDs. This motherboard only supports
M.2 PCIe SSDs. Please note that an M.2 PCIe SSD cannot be used to create a RAID set with a SATA
hard drive. Please navigate to the "Configuring a RAID Set" page of GIGABYTE's website for instructions
on configuring a RAID array. _3 U

M2A_CPU
110 80

M2P_CPU
110 80

M2C_SB
110 80

Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
M2A_CPU:
Step 1:
Use a screwdriver to unfasten the screws on the motherboard heatsink and then remove the motherboard
heatsink. Locate the proper mounting hole based on the length of your M.2 SSD drive.
To install an M.2 SSD in the 110mm hole, remove the standoff on the 80mm hole first and use the
heatsink screw to secure the heatsink and SSD.
Step 2:
Insert the M.2 SSD into the M.2 connector at an angle. Press the M.2 SSD down and then use the included
screw to secure it in the connector.
Step 3:
Remove the protective film from the thermal pad on the bottom of the heatsink. Then replace the heatsink
and secure it to the original hole.

M2P_CPU/M2C_SB:
Step 1:
Locate the proper mounting hole based on the length of your M.2 SSD drive. If needed, move the M.2 clip
to the desired mounting hole.
Step 2:
Pull the clip's tab up and out of the mounting hole. Slide the M.2 SSD into the connector at an angle. Press
down on the front end of the M.2 SSD and then secure it by pressing the clip's tab into the mounting hole.

* Types of M.2 SSDs supported by each M.2 connector:

M.2 PCIe x4 SSD M.2 PCIe x2 SSD M.2 SATA SSD
M2A_CPU a a r

M2P_CPU r a r

M2C_SB a a r

- 25 -
11) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator
on the chassis to this header according to the pin assignments below. Note the positive and negative pins
before connecting the cables.
Power LED Power Switch Speaker

PLED+

PW+

SPEAK+

SPEAK-
PLED-
G.QBOFM

PW-

NC
NC
2 20
1 19

PWR_LED+
HD-

CI+
RES+

PWR_LED-
PWR_LED-
-IC
HD+

RES-
Hard Drive Reset Power LED
Activity LED Switch
Chassis Intrusion
Header

•• PLED/PWR_LED (Power LED):

System Status LED Connects to the power status indicator on the chassis front panel. The LED
S0 On is on when the system is operating. The LED is off when the system is in S3/
S3/S4/S5 Off S4 sleep state or powered off (S5).

•• PW (Power Switch):
Connects to the power switch on the chassis front panel. You may configure the way to turn off your
system using the power switch (please navigate to the "BIOS Setup" page of GIGABYTE's website and
search for "Soft-Off by PWR-BTTN" for more information).
•• SPEAK (Speaker):
Connects to the speaker on the chassis front panel. The system reports system startup status by issuing
a beep code. One single short beep will be heard if no problem is detected at system startup.
•• HD (Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
•• RES (Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
if the computer freezes and fails to perform a normal restart.
•• CI (Chassis Intrusion Header):
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has
been removed. This function requires a chassis with a chassis intrusion switch/sensor.
•• NC: No connection.

The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis
front panel module to this header, make sure the wire assignments and the pin assignments are
matched correctly.

- 26 -
 _

_ _B _ S _
12) F_AUDIO (Front Panel Audio Header)
The front panel audio header supports High Definition audio (HD). You may connect your chassis front _ F
_
panel audio module to this header. Make sure the wire assignments of the module connector match the
pin assignments of the motherboard header. Incorrect connection between the module connector and the
motherboard header will make the device unable to work or even damage it.

_ Pin No. Definition

_0
1 MIC L
2 GND
9 1 3 MIC R
10 2 4 NC
5 Head Phone R
6 MIC Detection
_ S F_ 7 SENSE_SEND
8 No Pin
9 Head Phone L
B_ 10 Head Phone Detection
B S S_F

Some chassis provide a front panel audio module that has separated connectors on each wire
instead of a single plug. For information about connecting the front panel audio module that has
different wire assignments, please contact the chassis manufacturer.
_ F _3

F_
13) F_U32C (USB Type-C® Header, with USB 3.2
F_ Gen 1 Support)
The header conforms to USB 3.2 Gen 1 specification and can provide one USB port.

F_USB3 F_USB30 3 Pin No. Definition Pin No. Definition

B_
1 VBUS 11 VBUS
10 11
USB 0_ B 2 TX1+ 12 TX2+
3 TX1- 13 TX2-
1 20 4 GND 14 GND
5 RX1+ 15 RX2+
6 RX1- 16 RX2-
7 VBUS 17 GND
8 CC1 18 D-
9 SBU1 19 D+
10 SBU2 20 CC2

- 27 -
14) F_U32 (USBF_USB30
3.2 Gen 1 Header) F_ U F_
The header conforms to USB 3.2 Gen 1 and USB 2.0 specification and can provide two USB ports. For
purchasing the optional 3.5" front panel that provides two USB 3.2 Gen 1 ports, please contact the local
dealer.

Pin No. Definition Pin No. Definition

1 VBUS 11 D2+
20 1
2 SSRX1- 12 D2-
3 SSRX1+ 13 GND
4 GND 14 SSTX2+
B SS
5B_ SSTX1- 15 SSTX2-
6 SSTX1+ 16 GND

1
1

11 10 7 GND 17 SSRX2+ 1
_

1
8 D1- 18 SSRX2-
9 D1+ 19 VBUS
10 NC 20 No Pin
S
1 2 3

1 2 3

1 2 3
1 2 3

15) F_USB1/F_USB2/F_USB3 (USB 2.0/1.1 Headers)

The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an
optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Definition

1 Power (5V)
B SS S U
S 3 2 Power (5V)
3 USB DX-
9 1
10 2
4 USB DY-
5 USB DX+
6 USB DY+
S _
S F
7 GND
8 GND _

9 No Pin
10 NC

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power_cord
B_
from the power outlet to prevent damage to the USB bracket. S _S

S _
- 28 -
_S
16) COM (Serial Port Header) j
The COM header can provide one serial port via an optional COM port cable. For purchasing the optional
COM port cable, please contact the local dealer.
_ B S_
B B

Pin No. Definition

1 NDCD-
S B_ 2 NSIN
9 1
B 10 2 3 NSOUT
4 NDTR-
5 GND
6 NDSR-
7 NRTS-
_ S
8 NCTS-
S_ 9 NRI-
_
B 10 No Pin

_ U
_ F
_ _ 3 B

F_USB3 F

_0

17) SPI_TPM (Trusted Platform Module Header)

You may connect an SPI TPM (Trusted Platform Module) to this header.
_ _B _ S _

Pin No. Definition _ F

1 Data Output
11 1
2 Power (3.3V)
12 2 3 No Pin
4 NC
_ 5 Data Input
6 _0 F
CLK
7 Chip Select
8 GND
9 IRQ
10 NC
11 NC
S F_ 12 RST

B S S_F B_

j Only for B650 EAGLE AX.

- 29 -

_ F _3 U
18) BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one minute.
(Or use a metal object like a screwdriver to touch the positive and negative
terminals of the battery holder, making them short for 5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.

•• Always turn off your computer and unplug the power cord before replacing the battery.
•• Replace the battery with an equivalent one. Damage to your devices may occur if the battery is
replaced with an incorrect model.
•• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model.
•• When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up).
•• Used batteries must be handled in accordance with local environmental regulations.

19) CLR_CMOS (Clear CMOS Jumper)

Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear
the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

Open: Normal

Short: Clear CMOS Values

•• Always turn off your computer and unplug the power cord from the power outlet before clearing
the CMOS values.
•• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or
manually configure the BIOS settings (please navigate to the "BIOS Setup" page of GIGABYTE's
website for more information).

- 30 -
 Chapter 3 BIOS Setup
BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the
motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,
saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows
the user to modify basic system configuration settings or to activate certain system features.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to
keep the configuration values in the CMOS.

To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.

To upgrade the BIOS, use either the GIGABYTE Q-Flash or Q-Flash Plus utility.
•• Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
•• Q-Flash Plus allows you to update the BIOS when your system is off (S5 shutdown state). Save the latest
BIOS on a USB thumb drive and plug it into the dedicated port, and then you can now flash the BIOS
automatically by simply pressing the Q-Flash Plus button.
For instructions on using the Q-Flash and Q-Flash Plus utilities, please navigate to the "Unique Features" page
of GIGABYTE's website and search for "BIOS Update Utilities."

•• Because BIOS flashing is potentially risky, if you do not encounter problems using the current
version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with
caution. Inadequate BIOS flashing may result in system malfunction.
•• It is recommended that you not alter the default settings (unless you need to) to prevent system
instability or other unexpected results. Inadequately altering the settings may result in system's
failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
•• Refer to the introductions of the battery/clear CMOS jumper in Chapter 2 or navigate to the "BIOS
Setup" page of GIGABYTE's website and search for "Load Optimized Defaults" for how to clear
the CMOS values.

&& Please visit GIGABYTE's website for details on configuring BIOS Setup.
https://www.gigabyte.com/WebPage/917/amd600-bios.html

- 31 -
Startup Screen:

The following startup Logo screen will appear when the computer boots.

Function Keys

Function Keys:
<DEL>: BIOS SETUP\Q-FLASH
Press the <Delete> key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup.

<F12>: BOOT MENU

Boot Menu allows you to set the first boot device without entering BIOS Setup. In Boot Menu, use the up
arrow key <h> or the down arrow key <i> to select the first boot device, then press <Enter> to accept.
The system will boot from the device immediately.
Note: The setting in Boot Menu is effective for one time only. After system restart, the device boot order
will still be based on BIOS Setup settings.

<END>: Q-FLASH
Press the <End> key to access the Q-Flash utility directly without having to enter BIOS Setup first.

- 32 -
Chapter 4 Installing the Operating System and Drivers
4-1 Operating System Installation
With the correct BIOS settings, you are ready to install the operating system.

As some operating systems already include RAID driver, you do not need to install separate RAID driver during
the Windows installation process. After the operating system is installed, we recommend that you install all
required drivers from the GIGABYTE Control Center to ensure system performance and compatibility. If the
operating system to be installed requires that you provide additional RAID driver during the OS installation
process, please refer to the steps below:

Step 1:
Go to GIGABYTE's website, browse to the motherboard model's web page, download the AMD RAID Preinstall
Driver file on the Support\Download\SATA RAID/AHCI page, unzip the file and copy the files to your USB
thumb drive.

Step 2:
Boot from the Windows setup disc and perform standard OS installation steps. When the screen requesting you
to load the driver appears, select Browse.

Step 3:
Insert the USB thumb drive and then browse to the location of the drivers. Follow the on-screen instructions to
install the following three drivers in order.
j AMD-RAID Bottom Device
k AMD-RAID Controller
l AMD-RAID Config Device
Finally, continue the OS installation.

- 33 -
4-2 Drivers Installation
After you install the operating system, a dialog box will appear on the bottom-right corner of the desktop asking
if you want to download and install the drivers and GIGABYTE applications via GIGABYTE Control Center
(GCC). Click Install to proceed with the installation. (In BIOS Setup, make sure Settings\Gigabyte Utilities
Downloader Configuration\Gigabyte Utilities Downloader is set to Enabled.)

When the End User License Agreement dialog box appears, press <Accept> to install GIGABYTE Control Center (GCC).
On the GIGABYTE CONTROL CENTER screen, select the drivers and applications you want to install and
click Install.

Before the installation, make sure the system is connected to the Internet.

&& Please visit GIGABYTE's website for more software information.

https://www.gigabyte.com/WebPage/916/amd600-app.html

&& Please visit GIGABYTE's website for more troubleshooting information.

https://www.gigabyte.com/WebPage/351/faq.html

- 34 -
Chapter 5 Appendix
5-1 Configuring a RAID Set
RAID Levels
RAID 0 RAID 1 RAID 10
Minimum Number of ≥2 2 4
Hard Drives
Number of hard drives * (Number of hard drives/2) *
Array Capacity Size of the smallest drive
Size of the smallest drive Size of the smallest drive
Fault Tolerance No Yes Yes

Before you begin, please prepare the following items:

This motherboard supports RAID 0, RAID 1, and RAID 10. Prepare the correct number of hard drives as indicated
in the table above before configuring a RAID array.
•• SATA hard drives or SSDs. To ensure optimal performance, it is recommended that you use two hard drives
with identical model and capacity.
•• Windows setup disc.
•• An Internet connected computer.
•• A USB thumb drive.

An M.2 PCIe SSD cannot be used to set up a RAID set with a SATA hard drive.

&& Please visit GIGABYTE's website for details on configuring a RAID array.
https://www.gigabyte.com/WebPage/918/amd600-raid.html

- 35 -
Regulatory Notices
United States of America, Federal Communications Commission Statement

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Product Name: Motherboard

Trade Name: GIGABYTE
Model Number: B650 EAGLE AX/B650 UD AC

Responsible Party – U.S. Contact Information: G.B.T. Inc.

Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: 1-626-854-9338
Internet contact information: https://www.gigabyte.com

FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules, Subpart B, Unintentional Radiators.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted
by FCC certified equipment. The Intel PRO/Wireless 5000 LAN products meet the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/
IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC's
recommended limits.
The following safety precautions should be observed:
•• Do not touch or move antenna while the unit is transmitting or receiving.
•• Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face
or eyes, while transmitting.
•• Do not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged.
•• Use in specific environments:
- The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments.
- The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA).
- The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.

Antenna use: damage to this device. The maximum allowed antenna gain for use with
In order to comply with FCC RF exposure limits, low gain integrated this device is 6dBi in order tocomply with the E.I.R.P limit for the 5.25-to
antennas should be located at a minimum distance of 7.9 inches (20 cm) 5.35 and 5.725 to 5.85 GHz frequency range in point-to-point operation. To
or more from the body of all persons. comply with RF exposure requirements all antennas should be located at a
Explosive Device Proximity Warning minimum distance of 20cm, or the minimum separation distance allowed
Warning: Do not operate a portable transmitter (such as a wireless network by the module approval, from the body of all persons.
device) near unshielded blasting caps or in an explosive environment Attention: l'utilisation d'un réseau sans fil IEEE802.11a est restreinte à
unless the device has been modified to be qualified for such use. une utilisation en intérieur à cause du fonctionnement dansla bande de
Antenna Warning fréquence 5.15-5.25 GHz. Industry Canada requiert que ce produit soit
The wireless adapter is not designed for use with high-gain antennas. utilisé à l'intérieur des bâtiments pour la bande de fréquence 5.15-5.25 GHz
afin de réduire les possibilités d'interférences nuisibles aux canaux
Use On Aircraft Caution co-existants des systèmes de transmission satellites. Les radars de
Caution: Regulations of the FCC and FAA prohibit airborne operation of puissances ont fait l'objet d'une allocation primaire de fréquences dans
radio-frequency wireless devices because their signals could interfere with les bandes 5.25-5.35 GHz et 5.65-5.85 GHz. Ces stations radar peuvent
critical aircraft instruments. créer des interférences avec ce produit et/ou lui être nuisible. Le gain
Other Wireless Devices d'antenne maximum permissible pour une utilisation avec ce produit
Safety Notices for Other Devices in the Wireless Network: Refer to the est de 6 dBi afin d'être conforme aux limites de puissance isotropique
documentation supplied with wireless Ethernet adapters or other devices rayonnée équivalente (P.I.R.E.) applicable dans les bandes 5.25-5.35 GHz
in the wireless network. et 5.725-5.85 GHz en fonctionnement point-à-point. Pour se conformer aux
conditions d'exposition de RF toutes les antennes devraient être localisées
Canada, Canada-Industry Notice: à une distance minimum de 20 cm, ou la distance de séparation minimum
This device complies with Industry Canada license-exempt RSS permise par l'approbation du module, du corps de toutes les personnes.
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and Under Industry Canada regulations, this radio transmitter may only operate
(2) this device must accept any interference, including interference that using an antenna of a type and maximum (or lesser) gain approved for
may cause undesired operation of the device. the transmitter by Industry Canada. To reduce potential radio interference
Cet appareil est conforme aux normes Canada d'Industrie de RSS to other users, the antenna type and its gain should be chosen so that
permis-exempt. L'utilisation est assujetti aux deux conditions suivantes: the equivalent isotropically radiated power (e.i.r.p.) is not more than that
(1) le dispositif ne doit pas produire de brouillage préjudiciable, et necessary for successful communication.
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage Conformément à la réglementation d'Industrie Canada, le présent émetteur
susceptible de provoquer un fonctionnement indésirable. radio peut fonctionner avec une antenne d'un type et d'un gain maximal
Caution: When using IEEE 802.11a wireless LAN, this product is restricted (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
to indoor use due to its operation in the 5.15-to 5.25-GHz frequency but de réduire les risques de brouillage radio électrique à l'intention des
range. Industry Canada requires this product to be used indoors for the autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte
frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
harmful interference to co-channel mobile satellite systems. High power l'intensité nécessaire à l'établissement d'une communication satisfaisante.
radar is allocated as the primary user of the 5.25-to 5.35-GHz and 5.65 to
5.85-GHz bands. These radar stations can cause interference with and/or

- 36 -
European Union (EU) CE Declaration of Conformity CE Declaración de conformidad
This device complies with the following directives: Electromagnetic Este producto que llevan la marca CE cumplen con las siguientes
Compatibility Directive 2014/30/EU, Low-voltage Directive 2014/35/EU, Directivas de la Unión Europea: Directiva EMC 2014/30/EU, Directiva de
Radio Equipment Directive 2014/53/EU, ErP Directive 2009/125/EC, RoHS bajo voltaje 2014/35/EU, Directiva de equipamentos de rádio 2014/53/EU,
directive (recast) 2011/65/EU & the 2015/863 Statement. Directiva RoHS 2011/65/EU y la Declaración 2015/863.
This product has been tested and found to comply with all essential El cumplimiento de estas directivas se evalúa mediante las normas
requirements of the Directives. europeas armonizadas.
European Union (EU) RoHS (recast) Directive 2011/65/EU & the CE Dichiarazione di conformità
European Commission Delegated Directive (EU) 2015/863 Statement I prodotti con il marchio CE sono conformi con una o più delle seguenti
GIGABYTE products have not intended to add and safe from hazardous Direttive UE, come applicabile: Direttiva EMC 2014/30/UE, Direttiva sulla
substances (Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP, DBP and DIBP). bassa tensione 2014/35/UE, Direttiva di apparecchiature radio 2014/53/
The parts and components have been carefully selected to meet RoHS UE, Direttiva RoHS 2011/65/EU e Dichiarazione 2015/863.
requirement. Moreover, we at GIGABYTE are continuing our efforts to La conformità con tali direttive viene valutata utilizzando gli Standard
develop products that do not use internationally banned toxic chemicals. europei armonizzati applicabili.
European Union (EU) Community Waste Electrical & Electronic Deklaracja zgodności UE Unii Europejskiej
Equipment (WEEE) Directive Statement Urządzenie jest zgodne z następującymi dyrektywami: Dyrektywa
GIGABYTE will fulfill the national laws as interpreted from the 2012/19/ kompatybilności elektromagnetycznej 2014/30/UE, Dyrektywa
EU WEEE (Waste Electrical and Electronic Equipment) (recast) directive. niskonapięciowej 2014/35/UE, Dyrektywa urządzeń radiowych 2014/53/
The WEEE Directive specifies the treatment, collection, recycling and UE, Dyrektywa RoHS 2011/65/UE i dyrektywa2015/863.
disposal of electric and electronic devices and their components. Under Niniejsze urządzenie zostało poddane testom i stwierdzono jego zgodność
the Directive, used equipment must be marked, collected separately, and z wymaganiami dyrektywy.
disposed of properly.
ES Prohlášení o shodě
WEEE Symbol Statement Toto zařízení splňuje požadavky Směrnice o Elektromagnetické
The symbol shown below is on the product or on its kompatibilitě 2014/30/EU, Směrnice o Nízkém napětí 2014/35/EU,
packaging, which indicates that this product must not be Směrnice o rádiových zařízeních 2014/53/EU, Směrnice RoHS 2011/65/
disposed of with other waste. Instead, the device should be EU a 2015/863.
taken to the waste collection centers for activation of the Tento produkt byl testován a bylo shledáno, že splňuje všechny základní
treatment, collection, recycling and disposal procedure. požadavky směrnic.

For more information about where you can drop off your waste equipment EK megfelelőségi nyilatkozata
for recycling, please contact your local government office, your household A termék megfelelnek az alábbi irányelvek és szabványok
waste disposal service or where you purchased the product for details of követelményeinek, azok a kiállításidőpontjában érvényes, aktuális
environmentally safe recycling. változatában: EMC irányelv 2014/30/EU, Kisfeszültségű villamos
berendezésekre vonatkozó irányelv 2014/35/EU, rádióberendezések
Battery Information irányelv 2014/53/EU, RoHS irányelv 2011/65/EU és 2015/863.
European Union—Disposal and recycling information
GIGABYTE Recycling Program (available in some regions) Δήλωση συμμόρφωσης ΕΕ
Είναι σε συμμόρφωση με τις διατάξεις των παρακάτω Οδηγιών
της Ευρωπαϊκής Κοινότητας: Οδηγία 2014/30/ΕΕ σχετικά με την
ηλεκτρομαγνητική συμβατότητα, Οοδηγία χαμηλή τάση 2014/35/EU,
Οδηγία 2014/53/ΕΕ σε ραδιοεξοπλισμό, Οδηγία RoHS 2011/65/ΕΕ
This symbol indicates that this product and/or battery should not be και 2015/863.
disposed of with household waste. You must use the public collection Η συμμόρφωση με αυτές τις οδηγίες αξιολογείται χρησιμοποιώντας τα
system to return, recycle, or treat them in compliance with the local ισχύοντα εναρμονισμένα ευρωπαϊκά πρότυπα.
regulations.
End of Life Directives-Recycling
The symbol shown below is on the product or on its packaging, D33006
RoHS
which indicates that this product must not be disposed of with
other waste. Instead, the device should be taken to the waste
collection centers for activation of the treatment, collection, WARNING
recycling and disposal procedure. •• INGESTION HAZARD: This product contains a button cell or
coin battery.
Déclaration de Conformité aux Directives de l'Union européenne (UE) •• DEATH or serious injury can occur if ingested.
Cet appareil portant la marque CE est conforme aux directives de l'UE • A swallowed button cell or coin battery can cause Internal
suivantes: directive Compatibilité Electromagnétique 2014/30/UE, directive Chemical Burns in as little as 2 hours.
Basse Tension 2014/35/UE, directive équipements radioélectriques •• KEEP new and used batteries OUT OF REACH of CHILDREN
•• Seek immediate medical attention if a battery is suspected to
2014/53/UE, la directive RoHS II 2011/65/UE & la déclaration 2015/863. be swallowed or inserted inside any part of the body.
La conformité à ces directives est évaluée sur la base des normes
européennes harmonisées applicables. - Battery type: CR2032
- Non-rechargeable batteries are not to be recharged.
European Union (EU) CE-Konformitätserklärung - Remove and immediately recycle or dispose of used batteries, batteries
Dieses Produkte mit CE-Kennzeichnung erfüllen folgenden EU-Richtlinien: from equipment not used for an extended period of time according to local
EMV-Richtlinie 2014/30/EU, Niederspannungsrichtlinie 2014/35/EU, regulations and keep away from children. Do NOT dispose of batteries in
Funkanlagen Richtlinie 2014/53/EU, RoHS-Richtlinie 2011/65/EU erfüllt household trash or incinerate.
und die 2015/863 Erklärung. - Even used batteries may cause severe injury or death.
Die Konformität mit diesen Richtlinien wird unter Verwendung der - Do not force discharge, recharge, disassemble, heat above (manufacturer's
entsprechenden Standards zurEuropäischen Normierung beurteilt. specified temperature rating) or incinerate. Doing so may result in injury due
to venting, leakage or explosion resulting in chemical burns.
CE declaração de conformidade
- For treatment information, call a local poison control center.
Este produto com a marcação CE estão em conformidade com das
- Ensure the batteries are installed correctly according to polarity (+ and -).
seguintes Diretivas UE: Diretiva Baixa Tensão 2014/35/EU; Diretiva
- Do not mix old and new batteries, different brands or types of batteries,
CEM 2014/30/EU; Diretiva RSP 2011/65/UE e a declaração 2015/863.
such as alkaline, carbon-zinc, or rechargeable batteries.
A conformidade com estas diretivas é verificada utilizando as normas
europeias harmonizadas.

- 37 -
European Community Radio Equipment Directive Compliance Statement:

This equipment complies with all the requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU.
This equipment is suitable for home and office use in all the European Community Member States and EFTA Member States.
The low band 5.15 -5.35 GHz is for indoor use only.
AT BE BG CH CY CZ DE
DK EE EL ES FI FR HR
HU IE IS IT LI LT LU
LV MT NL PL PT RO SE
SI SK TR UK

NCC Wireless Statements / 無線設備警告聲明：

低功率電波輻射性電機管理辦法
(1) 取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特
性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至
無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或
工業、科學及醫療用電波輻射性電機設備之干擾。
(2) 應避免影響附近雷達系統之操作。

Korea KCC NCC Wireless Statement:

5,25GHz - 5,35 GHz 대역을 사용하는 무선 장치는 실내에서만 사용하도록 제한됩니다 .

Japan Wireless Statement:

5.15 GHz 帯 ~ 5.35 GHz 帯 : 屋内のみの使用。

Wireless module approvals:

To identify your Motherboard version or revision number, look for "REV: X.X" printed on the PCB on the top left corner of the Motherboard. For
example, "REV:1.0" means the revision of the motherboard is 1.0.
Motherboard: Wireless module manufacturer, model name:
B650 EAGLE AX Realtek Semiconductor Corp. RTL8852CE
B650 UD AC Realtek Semiconductor Corp. RTL8821CE

Approvals for wireless module RTL8852CE:

Approvals for wireless module RTL8821CE:

- 38 -
 Contact Us

GIGA-BYTE TECHNOLOGY CO., LTD.

Address: No.6, Baoqiang Rd., Xindian Dist., New Taipei City 231
TEL: +886-2-8912-4000, FAX: +886-2-8912-4005
Tech. and Non-Tech. Support (Sales/Marketing) : https://esupport.gigabyte.com
WEB address (English): https://www.gigabyte.com
WEB address (Chinese): https://www.gigabyte.com/tw

•• GIGABYTE eSupport
To submit a technical or non-technical (Sales/Marketing) question, please link to:
https://esupport.gigabyte.com

- 39 -