Module 1 Free Electrons: The valence electrons which are loosely attached to the nucleus of an atom and

free to move when external energy is applied are called free electrons.
D.C. Circuits
Electrical Potential: The capacity of charged body to do work is called electrical potential.
Electricity: Electricity plays an important role in our day to day life. 𝐖𝐨𝐫𝐤𝐝𝐨𝐧𝐞 𝐖
Electricity is used for Electrical Potential = =
𝑪𝒉𝒂𝒓𝒈𝒆 𝑸
1. Lighting ( lamps)
2. Heating( heaters) 𝐖
V=
3. Cooling 𝑸
4. Entertainment ( T.V. and radio) Unit of electrical potential is Vollts or Joules/Coulomb.
5. Transportation Def: A body is said to have an electric potential of 1 Volt if 1 Joule of work is done to charge
6. Calculations( Calculators) the body to 1 coulomb.
Now- a- days all the activities are dependent upon electricity.
Electricity: The invisible energy which constitutes flow of electrons in a closed circuit to do Potential Difference:
work is called electricity. The difference in electrical potential of the two charged bodies is called potential difference.
Unit of potential difference is Volts.
Nature of Electricity: Every matter is electrical in nature since it contains charged particles like
electrons and protons. Therefore Electric Current: In metallic wire, a large number of electrons are available which move from
1. Ordinarily, a body is neutral as it contains same number of protons and electrons. one atom to other at random.
2. If some of electrons are removed from the body, there is a deficit of electrons and the
body attains a positive charge. When an electrical potential is applied across a metallic wire, the loosely attached free electron
3. If some of electrons are supplied to the body, there occurs excess of electrons and the start moving towards positive terminal of the cell.
body attains a negative charge.

Thus, continuous flow of electrons in an electric circuit is called electric current

Definition-
A body is said to be charged +vely or –vely if it has deficit or excess of electrons from its normal Current is rate of flow of electrons i.e. charge flowing per second.
due share respectively. 𝑸
I=
𝒕
Unit of Charge: The unit of current is Ampere (A)
The practical unit of charge is coulomb.
One Coulomb= charge on 6.28 x 1018 electrons.
 Limitations of Ohm’s Law
E.M.F. (Electromotive force) and potential difference:
E.m.f is the force that causes an electric current to flow in an electric circuit.  Ohm‟s law is not applicable in unilateral networks. Unilateral networks allow the current
Infact it is not a force but it is an energy. to flow in one direction. Such types of network consist of elements like a diode,
E.m.f: The electromotive force is the amount of energy supplied by the source to each transistor, etc.
coulomb of charge.  It is not applicable for the non-linear network (network containing non-linear elements
Potential Difference: The potential difference is the amount of energy used by the one such as electric arc etc). In the nonlinear network, the parameter of the network is varied
coulomb of charge in moving from one point to the other. with the voltage and current. Their parameter likes resistance, inductance, capacitance
In the following figure battery has emf of 12V and the potential difference between A and B is and frequency, etc., not remain constant with the times. So ohms law is not applicable to
7V. the nonlinear network. Ohm‟s law is used for finding the resistance of the circuit and also
for knowing the voltage and current of the circuit.

Resistance: The opposition offered to flow of current is called resistance. It is represented by R.

The unit of resistance is ohms (Ω)

E=12
V
Ohm’s Law
Ohm‟s laws state that the current through any two points of the conductor is directly proportional
to the potential difference applied across the conductor, provided physical conditions i.e.
temperature, etc. do not change. It is measured in (Ω) ohm.

Mathematically it is expressed as

Law of Resistance: The resistance of a wire depends upon

1. It is directly proportional to its length.
R α L ………………. 1
2. It is inversely proportional to its area of cross-section.
1
R α 𝐴 ………………..2
This constant is also called the resistance (R) of the conductor (or circuit)
3. It depends upon the nature of material of which the wire is made.
𝑉 4. It also depends upon the temperature of the wire.
R= 𝐼
Combining 1 and 2
𝐿
In a circuit, when current flows through a resistor, the potential difference across the resistor is Rα𝐴
known as voltage drops across it, i.e., V = IR. ρL
R=
𝐴
 Electric Circuit:
The close path for flow of electric current is called electric circuit. The electric circuit is an
arrangement of electrical energy sources and various circuit elements such as R, L and C are
connected in series, parallel or series parallel combinations.

Circuit Elements:
The circuit elements can be categorized as:
Numerical on OHM’s law 1. Active and passive elements
2. Unilateral and bilateral elements
1. A wire of length 1 m has a resistance of 2 ohms. Obtain the resistance if specific
3. Linear and non-linear elements
resistance is double, the diameter is double and the length is made three times the first.
4. Lumped and distributed elements
2. There are two wires A& B of same material. A is 20 times longer than B and has one fifth
1. Active and passive elements:
of the cross-section as that of B. If the resistance of A is 1 ohm. What is the resistance of
B? Active elements are those who supply energy or power in the form of a voltage or current to the
circuit or network.
Examples of the active components are batteries or generators etc.
Passive elements are those who receive energy in the form of voltage or current.
Examples of the passive components are resistor, capacitor and inductor.
2. Unilateral and bilateral elements:
Unilateral elements: The elements which conduct the current in one direction only are called
unilateral elements such as diodes, transistors, vacuum tubes, rectifiers etc
Bilateral elements: The elements which conduct the current in both the directions are called
bilateral elements such as resistors.
3. Linear and non-linear elements
Linear Elements: The elements which follow the linear relation between current and voltage.
e.g. resistors
Non Linear Elements: The elements which don‟t follow the linear relation between current and
voltage. e.g. Diode and transistors
4. Lumped and distributed elements:
Lumped elements: The elements in which action takes place simultaneously are lumped elements
such as resistor, capacitor and inductor. These elements are smaller in size.
Distributed elements: The elements in which for a given cause is not occurring simultaneously at
the same instant but it is distributed are called distributed elements such as transmission lines.
Voltage and Current Source: Examples of independent voltage source batteries and generators.
To deliver electrical energy to the electrical circuits, a source is required and a load is connected Examples of independent current source semiconductor devices such as Diode and transistors

to source as shown in fig.

Dependent voltage/ current source:
The voltage does dependent on another voltage or current in the circuit.
Symbol for dependent voltage and current source

The source may be d.c. source or a.c source.

D.C. source:
Ideal and practical voltage sources:
Any source that produces direct voltage continuously and has ability to deliver direct current is
Ideal voltage sources: An imaginary voltage source, which can provide a constant voltage to load
called d.c. source such as batteries and generators etc.
ranging from zero to infinity. Such voltage source is having zero internal resistance, Rs and is
A.C. source:
called Ideal Voltage Source. Practically it is not possible to build a voltage source with no
Any source that produces alternating voltage continuously and has ability to deliver the
internal resistance and constant voltage for that long range of the load.
alternating current is called a.c. source such as alternators, oscillators or signal generators.
Independent and dependent sources:
There are two types of sources- Voltage source and current source. Sources can be either
independent or dependent upon some other quantities.
Independent voltage/ current source:
The voltage ( a.c or d.c.) does not dependent on other voltages or current in the circuit.
Symbol for independent voltage and current source Practical voltage sources: Practical voltage sources always have some resistance value in series
with an ideal voltage source and because of that series resistance, voltage drops when current
passes through it. So, Practical Voltage Source has internal resistance and slightly variable
voltage.
 D. C. circuit: The closed path for flow of direct current is called D.C. circuit.
Source Transformation:
D.C Circuit is of two types:
1. Series Circuit
2. Parallel Circuit

Current in Parallel Circuit:

Then
 Network Terminology:
Voltage in Series Circuit:
1. Electric Network:
Electric network is interconnection of electric components. E.g. Batteries, resistors, inductors
and capacitors.
2. Electric Circuit:
The path for flow of electric current is called
electric circuit.
3. Active Elements:
The elements which supplies energy to the
circuit. In fig V1 and V2 are active elements.
4. Passive Elements:
The elements which receives energy. In fig
R1, R2 and R3 are passive elements.
5. Node:
Node is a point where two or more circuit elements are connected together. In Fig. A, B, C and E
are nodes.
6. Junction:
Junction is a point in the network where three or more circuit elements are connected together.
It is a point where current is divided. In Fig. B and E are junctions.
7. Loop:
The closed path of a network. E.g. ABEFA, BCDEB and ABCDEFA are loops.
8. Mesh:
The elementary form of loop which cannot be further divided is called mesh.
E.g. ABEFA, BCDEB are mesh.
Total resistance of the circuit is R=R1+R2 9. Branch:
Put the values of R in eqn 3 and 4 Part of a network which lies between two junction points. In fig. ABEFA, BCDEB AND BE are
the three branches.
 Kirchhoff’s Current Law or KCL important to maintain the same direction either clockwise or anti-clockwise or the final voltage
sum will not be equal to zero. We can use Kirchhoff‟s voltage law when analyzing series
Kirchhoff‟s Current Law or KCL, states that the “total current or charge entering a junction or circuits.
node is exactly equal to the charge leaving the node”. In other words the algebraic sum of all the
currents entering and leaving a node must be equal to zero, I(exiting) + I(entering) = 0. Analysis of simple circuits with Kirchhoff’s law

Kirchhoff‟s Current Law or KCL Q: Calculate current in given circuit using Kirchhoff's law.

Ans: Firstly we have to mark the direction of current in given circuit.

Here, the three currents entering the node, I1, I2, I3 are all positive in value and the two currents
leaving the node, I4 and I5 are negative in value. Then this means we can also rewrite the
equation as;

I1 + I2 + I3 – I4 – I5 = 0
The term Node in an electrical circuit generally refers to a connection or junction of two or more
current carrying paths or elements such as cables and components. Also for current to flow either
in or out of a node a closed circuit path must exist. We can use Kirchhoff‟s current law when Junction b: I1 + I2 + I3 = 0
analyzing parallel circuits.
So, I3 = - (I1 + I2)
Kirchhoff’s Voltage Law
Kirchhoff‟s Voltage Law or KVL, states that “in any closed loop network, the total voltage
around the loop is equal to the sum of all the voltage drops within the same loop” which is also
equal to zero. In other words the algebraic sum of all voltages within the loop must be equal to
zero.
Kirchhoff‟s Voltage Law or KVL

I3 = - (171-64) = -107mA

I3 = -107mA

Starting at any point in the loop continue in the same direction noting the direction of all the
voltage drops, either positive or negative, and returning back to the same starting point. It is
 Superposition theorem We can use the voltage divider technique because its resistors, R1 and R2, are connected in series
with a voltage source. So here‟s the voltage vo1 across resistor R2:

Superposition theorem states that in any linear, active, bilateral network having more than one
source, the response across any element is the sum of the responses obtained from each source
considered separately and all other sources are replaced by their internal resistance. The
superposition theorem is used to solve the network where two or more sources are present and
connected. Resulting current in any branch is the algebraic sum of all the currents that would be Considering Current source
produced in it.
Procedure for using superposition theorem
Step-1: Retain one source at a time in the circuit and replace all other sources with their internal
resistances.
Step-2: Determine the output (current or voltage) due to the single source acting alone using the
We can use a current divider technique because the resistors are connected in parallel with a
techniques discussed in lessons 3 and 4.
current source. The current source provides the following current i22 flowing through resistor R2:
Step-3: Repeat steps 1 and 2 for each of the other independent sources.
Step-4: Find the total contribution by adding algebraically all the contributions due to the
independent sources

Numerical We can use Ohm‟s law to find the voltage output vo2 across resistor R2

Calculate the total voltage in given fig using Superposition theorem

Now find the total output voltage across R2 for the two independent sources in Circuit C by
adding vo1 (due to the source voltage vs) and vo2 (due to the source current is). You wind up with
the following output voltage.
vo = vo1+vo2
vo = 2+2= 4 V
We need to turn off the independent sources one at a time. To do so, replace the current source
.
with an open circuit and the voltage source with a short circuit.
Considering the voltage source
 Norton’s Theorem
Statement: 𝑅𝑒𝑞
IL= ISC 𝑅𝑒𝑞 +𝑅𝐿
Norton‟s Theorem states that – A linear active network consisting of the independent or
dependent voltage source and current sources and the various circuit elements can be substituted
Where, IL is the load current, Isc is the short circuit current
by an equivalent circuit consisting of a current source in parallel with a resistance.
The current source being the short-circuited current across the load terminal and the resistance Req is the equivalentl resistance of the circuit, RL is the load resistance of the circuit
being the internal resistance of the source network.
The Norton‟s theorems reduce the networks equivalent to the circuit having one current source, Step 3: To find Req
parallel resistance and load. Norton‟s theorem is the converse of Thevenin‟s Theorem. It consists
of the equivalent current source instead of an equivalent voltage source as in Thevenin‟s Now the short circuit is removed, and the independent source is deactivated as shown in the
circuit diagram below and the value of the equivalent resistance is calculated by:
theorem.

Explanation of Norton’s Theorem

To understand Norton‟s Theorem in detail, let us consider a circuit diagram given below

Req

So,

Req= r1|| r3+ r2

In order to find the current through the load resistance IL as shown in the circuit diagram above
r1r3
Step 1: Req= +r2
𝑟1+𝑟3

Step 2: To find Isc

Req
Now, the value of current I flowing in the circuit is found out by the equation Solution of numerical

Step-1: Short the terminals „a‟ and „b‟ after disconnecting the 6.2 resistor. The Norton‟s current
IN for the circuit shown in fig. is computed by using „mesh-current‟ method.

And the short-circuit current ISC is given by the equation shown below:

Steps for Solving a Network Utilizing Norton’s Theorem

Step 1 – Norton‟s equivalent circuit is drawn by keeping the equivalent resistance Req in parallel
with the short circuit current ISC.

Step 2 – Find the internal resistance Req of the source network by deactivating the constant
sources.

Step 3 – Now short the load terminals and find the short circuit current ISC flowing through the
shorted load terminals using conventional network analysis methods.
Norton‟s resistance RN is computed by replacing all sources by their internal resistances while
Step 4 – Reconnect the load resistance RL of the circuit across the load terminals and find the the short-circuit across the output terminal „a‟ and „b‟ is removed. From the circuit diagram fig.
current through it known as load current IL. the Norton‟s resistance is obtained between the terminals „a‟ and „b‟.

This is all about Norton‟s Theorem.

Numerical

Applying Norton‟s theorem, find the maximum power dissipated by the resistor 6.2Ω under that
situation

Note that the maximum power will dissipate in load resistance when load resistance = Norton‟s
resistance RN=RL=6.2Ω. To satisfy this condition the value of the resistance can be obtained
from equation of RN we get R=2Ω. The circuit now replaced by an equivalent Norton‟s current
source.
  Reference Node – It is a node which acts a reference point to all the other node. It is also
called the Datum Node.

Solving of Circuit Using Nodal Analysis

Basic Steps Used in Nodal Analysis:

1. Select a node as the reference node. Assign voltages V1, V2… Vn-1 to the remaining
The maximum power delivered by the given network to the load RL=6.2Ω is thus given by nodes. The voltages are referenced with respect to the reference node.
2. Apply KCL to each of the non reference nodes.
3. Use Ohm‟s law to express the branch currents in terms of node voltages.

Nodal Analysis in Electric Circuits

4. After the application of Ohm‟s Law get the „n-1‟ node equations in terms of node voltages and
resistances.
Definition of Nodal Analysis
5. Solve „n-1‟ node equations for the values of node voltages and get the required node Voltages
Nodal analysis is a method that provides a general procedure for analyzing circuits using node as result.
voltages as the circuit variables. Nodal Analysis is also called the Node-Voltage Method.
In Node-Voltage Method, we can solve for unknown voltages in a circuit using KCL.

Thevenin’s Theorem
Some Features of Nodal Analysis:
Thevenin‟s Theorem states that “Any linear circuit containing several voltages and resistances
 Nodal Analysis is based on the application of the Kirchhoff‟s Current Law (KCL).
can be replaced by just one single voltage in series with a single resistance connected across the
 Having „n‟ nodes there will be „n-1‟ simultaneous equations to solve.
 Solving „n-1‟ equations all the nodes voltages can be obtained. load“. In other words, it is possible to simplify any electrical circuit, no matter how complex, to
 The number of non reference nodes is equal to the number of Nodal equations that can be an equivalent two-terminal circuit with just a single constant voltage source in series with a
obtained. resistance (or impedance) connected to a load as shown below.

Types of Nodes in Nodal Analysis Thevenin’s Theorem is especially useful in the circuit analysis of power or battery systems and
other interconnected resistive circuits where it will have an effect on the adjoining part of the
 Non Reference Node – It is a node which has a definite Node Voltage. e.g. Here Node 1
and Node 2 are the Non Reference nodes circuit.
Thevenin’s equivalent circuit The value of the equivalent resistance, Rs is found by calculating the total resistance looking
back from the terminals A and B with all the voltage sources shorted. We then get the following
circuit.

As far as the load resistor RL is concerned, any complex “one-port” network consisting of
multiple resistive circuit elements and energy sources can be replaced by one single equivalent
resistance Rs and one single equivalent voltage Vs. Rs is the source resistance value looking back
Find the Equivalent Resistance (Rs)
into the circuit and Vs is the open circuit voltage at the terminals.
10Ω resistor in parallel with 20Ω resistor

Rs = 10*20/10+20= 200/30= 6.67Ω

Find the load current in 40 Ω in given fig using Thevenin’s theorem The voltage Vs is defined as the total voltage across the terminals A and B when there is an open
circuit between them. That is without the load resistor RL connected.

Firstly, to analyze the circuit we have to remove the centre 40Ω load resistor connected across
the terminals A-B, and remove any internal resistance associated with the voltage source(s). This
is done by shorting out all the voltage sources connected to the circuit, that is v = 0, or open
circuit any connected current sources making i = 0. The reason for this is that we want to have an
ideal voltage source or an ideal current source for the circuit analysis.
 Time-domain analysis of first-order RL circuit(Transient Response)

The short timed electrical phenomenon that occurs in a system due to sudden change in voltage,
current of load is called transient response. Transients occur in the response due to sudden
change in the sources that are applied to the electric circuit and / or due to switching action.
The transient part occurs in the response of an electrical circuit or network due to the presence of
energy storing elements such as inductor and capacitor.

 The transient part will not present in the response of an electrical circuit or network, if it
contains only resistances. Because resistor is having the ability to adjust any amount of
voltage and current.
 The transient part occurs in the response of an electrical circuit or network due to the
presence of energy storing elements such as inductor and capacitor. Because they can‟t
change the energy stored in those elements instantly.
Consider the following series RL circuit diagram.

In the above circuit, the switch was kept open up to t = 0 and it was closed at t = 0. So, the DC
voltage source having V volts is not connected to the series RL circuit up to this instant.
Therefore, there is no initial current flow through inductor.
The circuit diagram, when the switch is in closed position is shown in the following figure.

Now, the current i flows in the entire circuit, since the DC voltage source having V volts is
connected to the series RL circuit.
Now, apply KVL around the loop.
The above equation is a first order differential equation and it is in the form of Substituting the value of k in Equation 4.

By comparing Equation 1 and Equation 2, we will get the following relations.

, Therefore, the current flowing through the circuit is

,
So, the response of the series RL circuit, when it is excited by a DC voltage source, has the
following two terms.

We can re-write the Equation 5 as follows

We know that there is no initial current in the circuit. Hence, substitute, t = 0 and 𝑖 = 0 in
Equation 4 in order to find the value of the constant k.

Where, τ is the time constant and its value is equal to L/R

Transient Response of RC Circuit: A A is a constant

Consider a Transient Response of RC Circuit consisting of resistance and capacitance as shown

in fig.

The current equation becomes

The capacitor in the circuit is initially uncharged, and is in series with a resistor. When the
switch S is closed at t = 0, we can determine. the complete solution for the current. Application
of the Kirchhoff‟s voltage law to the circuit results in the following differential equation.
When switch S is closed, the response decays with time as shown in Fig.

By differentiating the above equation, we get

In the solution, the quantity RC is the time constant, and is denoted by τ,

where τ = RC sec

After 5 TC, the curve reaches 99 per cent of its final value. In. Fig. , we can find out the voltage
across each element by using the current equation. Voltage across the resistor is

A
Similarly, voltage across the capacitor is Short Questions with answers
Module 1
Q1. State Ohm‟s law and its limitations.
Ans. Ohm‟s laws state that the current through any two points of the conductor is directly
proportional to the potential difference applied across the conductor, provided physical
conditions i.e. temperature, etc. do not change. It is measured in (Ω) ohm.
At t = 0, voltage across capacitor is zero Mathematically it is expressed as

The responses are shown in Fig. 12.8.

Power in the resistor

This constant is also called the resistance (R) of the conductor (or circuit)

𝑉
R= 𝐼
Power in the capacitor

In a circuit, when current flows through a resistor, the potential difference across the resistor is
known as voltage drops across it, i.e., V = IR.
Limitations of Ohm‟s Law
 Ohm‟s law is not applicable in unilateral networks. Unilateral networks allow the current
The responses are shown in Fig. to flow in one direction. Such types of network consist elements like a diode, transistor,
etc.
 It is not applicable for the non-linear network. In the nonlinear network, the parameter of
the network is varied with the voltage and current. Their parameter likes resistance,
inductance, capacitance and frequency, etc., not remain constant with the times. So ohms
law is not applicable to the nonlinear network. Ohm‟s law is used for finding the
resistance of the circuit and also for knowing the voltage and current of the circuit.
Q2. Differentiate between Ideal and practical voltage sources.
Ans. Ideal voltage sources: An imaginary voltage source, which can provide a constant voltage
to load ranging from zero to infinity. Such voltage source is having zero internal resistance, Rs
and is called Ideal Voltage Source. Practically it is not possible to build a voltage source with no Ans. The solution of the linear differential equation gives the response of the system. The
internal resistance and constant voltage for that long range of the load. representation of a electrical system by a linear differential equation of functions of time and its
solution is collectively called time domain analysis of electrical system
Q7.State Thevenin‟s Theorem
Ans. Thevenin‟s Theorem states that “Any linear circuit containing several voltages and
resistances can be replaced by just one single voltage in series with a single resistance connected
across the load“. In other words, it is possible to simplify any electrical circuit, no matter how
Practical voltage sources: Practical voltage sources always have some resistance value in series complex, to an equivalent two-terminal circuit with just a single constant voltage source in series
with an ideal voltage source and because of that series resistance, voltage drops when current with a resistance (or impedance) connected to a load .
passes through it. So, Practical Voltage Source has internal resistance and slightly variable Q8.If a 30 V source can force 1.5 A through a certain linear circuit, how much current can10 V
voltage force through the same circuit?
𝑉
Q3. How will you differentiate between Linear and Non Linear elements? Ans. R= 𝐼
Ans. In Electrical Circuits Linear Elements are the devices that follow the linear relation between 30
R=
1.5
current and voltage. e.g. an ideal Resistance.
R= 20 Ω
Non Linear Elements are devices which don't follow the linear relation between current and
V=IR
voltage. e.g. Diode.
𝑉 10
Q4. Differentiate between active and passive elements. I= , I =
𝑅 20

Ans. Active components are those who deliver or supply energy or power in the form of a I= 0.5 A
voltage or current. Passive components are those who utilizes or store energy in the form of Q9. State Norton‟s Theorem.
voltage or current. Ans. Norton‟s Theorem states that a linear active network consisting of independent or
Examples of the active components are Diodes, transistors, SCR, integrated circuits, etc. dependent voltage source and current sources and the various circuit elements can be substituted
Examples of the passive components are resistor, capacitor and inductor. by an equivalent circuit consisting of a current source in parallel with a resistance. The current
Q5. State superposition theorem. source being the short-circuited current across the load terminal and the resistance being the
Ans. Superposition theorem states that in any linear, active, bilateral network having more than internal resistance of the source network.
one source, the response across any element is the sum of the responses obtained from each Q10. State Kirchhoff‟s law.
source considered separately and all other sources are replaced by their internal resistance. The Ans. Kirchhoffs Current Law or KCL, states that the “total current or charge entering a junction
superposition theorem is used to solve the network where two or more sources are present and or node is exactly equal to the charge leaving the node”. In other words the algebraic sum of all
connected the currents entering and leaving a node must be equal to zero, I(exiting) + I(entering) = 0.
Q6. What do you mean by time domain analysis? Discuss Kirchhoffs Voltage Law or KVL, states that “in any closed loop network, the total voltage
around the loop is equal to the sum of all the voltage drops within the same loop” which is also