09-01-2025 12:26:09 PM

COMPUTER AIDED DRAWING AND SIMULATION Course Code : 314008

V. THEORY LEARNING OUTCOMES AND ALIGNED COURSE CONTENT

Suggested
Theory Learning Outcomes Learning content mapped with Theory
Sr.No Learning
(TLO's)aligned to CO's. Learning Outcomes (TLO's) and CO's.
Pedagogies.
Unit - I Electrical Drawings.
1.1 Symbols: Electrical and Electronic as per SP
30: 2023 Part 1, section 3.
TLO 1.1 Sketch the electrical
1.2 Types of electrical drawings (a) Power wiring
symbols as per requirement in
diagram (single line diagram (SLD) or Multiline
electrical drawings.
diagram) (b) Control wiring diagram (Schematic
TLO 1.2 Interpret given electrical Hands-on
diagram) (c) Block diagrams (d) Pictorial
power/control wiring diagram. Presentations
1 diagrams.
TLO 1.3 Identify types of electrical Lecture Using
1.3 Types of Electrical panels (a) MCC (Motor
panel. Chalk-Board
control center) Panel (b) PCC (Power control
TLO 1.4 Sketch GA Diagram of
center) panel (c) APFC (Automatic Power Factor
Electrical control panel (Assume
Controller) Panel (d) PLC (Programmable logic
suitable dimensions).
controller) Panel.
1.4 General Arrangement (GA) diagram of
Electrical control panel.
Unit - II Computer Aided Design (CAD)
TLO 2.1 Identify the function of the
Introduction.
given components of CAD classic
2.1 Components of CAD classic screen.
screen. Hands-on
2.2 Menu bar and status bar.
2 TLO 2.2 Identify the given Presentations
2.3 Open and Save file.
components of CAD screen. Demonstration
2.4 CAD Toolbars.
TLO 2.3 Identify the given toolbar
2.5 Command Box.
and commands.
2.6 Zoom in and Zoom out.
Unit - III CAD Tools and Commands.
3.1 Coordinate Method: Absolute, Relative, Polar.
Basic commands: Limits, Units.
3.2 Draw Toolbar: Line, Polyline, Circle, Arc,
TLO 3.1 Use the coordinate methods Rectangle, Ellipse, Polygon, Hatch.
and practice basic commands. 3.3 Modify Toolbar: Move, Rotate, Trim, Erase,
Hands-on
TLO 3.2 Practice Draw, Modify and Copy, Cut, Mirror, Fillet, Chamfer, Offset,
3 Demonstration
Annotation toolbar commands. Explode, Strech, Scale.
Presentations
TLO 3.3 Practice Important CAD 3.4 Annotation Toolbar: Multiline Text, Single
Modes. Line Test, Linear dimension, Aligned dimension,
Angular Dimension, Arc Length Dimension,
Radius Dimension, Diameter Dimension
3.5 Important CAD Modes : Grid, Ortho, Snap,
Polar Tracking, Object Snap Tracking.
TLO 4.1 Sketch the power wiring Unit - IV Use of CAD in Real World Electrical
diagram, control wiring diagram Engineering Drawings.
and GA Diagram of Electrical 4.1 Applications of electrical CAD software to:
control panel using CAD (a)Draw power wiring diagram of electrical
TLO 4.2 Sketch the Single line control panel. (b)Draw control wiring diagram
diagram (SLD) of the 11 kV/433 V of electrical control panel. (c)Draw GA diagram
Hands-on
distribution substation using CAD of electrical control panel.
4 Demonstration
TLO 4.3 Sketch the Single line 4.2 Applications of electrical CAD software to
Presentations
diagram (SLD) of Single line diagram (SLD) of the 11 kV/433 V
residential/commercial unit using distribution substation.
CAD 4.3 Prepare Single line diagram (SLD) of
TLO 4.4 Sketch the Single line residential/commercial unit using CAD.
diagram (SLD) of any industrial 4.4 Draw the Single line diagram (SLD) of any
plant using CAD industrial electrical installation using CAD.

MSBTE Approval Dt. 21/11/2024 Semester - 4, K Scheme

Page 2/8
 09-01-2025 12:26:09 PM

COMPUTER AIDED DRAWING AND SIMULATION Course Code : 314008

Suggested
Theory Learning Outcomes Learning content mapped with Theory
Sr.No Learning
(TLO's)aligned to CO's. Learning Outcomes (TLO's) and CO's.
Pedagogies.
TLO 5.1 Select and use softwares for
Electrical and electronic circuit Unit - V Simulation of Electrical and
simulations. Electronic Circuits.
TLO 5.2 Build, Simulate and Test 5.1 Voltage, current, power across (a)Series R-L
Basic electric circuits. circuit (b)Series R-C circuit (c)Series R-L-C
TLO 5.3 Build, Simulate and Test circuit. Hands-on
5 Basic electronic circuits. 5.2 Rectifier circuit, KVL and KCL simulation. Demonstration
TLO 5.4 Measure various electrical 5.3 Triac Lamp Dimmer Circuit simulation. Presentations
parameters and Generate or plot 5.4 Basic Logic Gate and adder circuit
relevant Waveforms/Graphs. simulation.
TLO 5.5 Develop P.C.B. layout for a 5.5 Printed Circuit Board (PCB) preparation
given electrical circuit using basic information.
software.

VI. LABORATORY LEARNING OUTCOME AND ALIGNED PRACTICAL / TUTORIAL EXPERIENCES.

Practical / Tutorial / Laboratory Sr Laboratory Experiment / Practical Titles / Number Relevant
Learning Outcome (LLO) No Tutorial Titles of hrs. COs
LLO 1.1 Draw symbols of
*Symbols of Electrical and Electronic Components
different electrical and electronic
1 as per SP 30: 2011(NEC 2011) part 1, section 3 or 2 CO1
components using drawing
new equivalent IS on sketch book.
instruments.
LLO 2.1 Draw Power and control *Power and Control wiring diagram of DOL
2 2 CO1
wiring diagram for DOL starter. Starter on sketch book.
LLO 3.1 Draw Power and control
*Power and Control wiring diagram of Star Delta
wiring diagram for Star Delta 3 2 CO1
Starter on sketch book.
starter.
LLO 4.1 Draw General
Arrangement (GA) Diagram for General Arrangement Diagram for Electrical Panel
4 2 CO1
DOL/Star delta starter panel or on sketch book (Assume suitable dimensions).
any other electrical panel.
LLO 5.1 Install CAD software.
LLO 5.2 Create new drawing.
LLO 5.3 Locate components of
5 *Different components of CAD classic screen. 2 CO2
CAD Classic Screen (CAD screen
layout, Drawing area, Menu and
Toolbars, Status bar).
LLO 6.1 Create and Save drawing.
LLO 6.2 Set the drawing Limits
*CAD file operations and Limits & Units of
and Units of the file. 6 2 CO2
Drawing.
LLO 6.3 Perform Zoom in and
Zoom out functionality.
LLO 7.1 Use Draw Toolbar of CAD * Basic geometrical shapes using Draw Toolbar
CO2
for drawing basic geometrical 7 commands (Line, Polyline, Circle, Arc, Rectangle, 2
CO3
shapes. Ellipse, Polygon, Hatch).
Modifying or editing basic geometrical shapes
LLO 8.1 Use Modify Toolbar of
using modify commands (Move, Rotate, Trim, CO2
CAD for modifying or editing CAD 8 2
Erase, Copy, Cut, Mirror, Fillet, Chamfer, Offset, CO3
drawing.
Explode, Stretch, Scale).

MSBTE Approval Dt. 21/11/2024 Semester - 4, K Scheme

Page 3/8