Introduction

▪ Computer assembly is a large part of a technician's job.

Work in a logical, methodical manner when working with
computer components
Improve computer assembly skills dramatically with practice

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 1
Overview of General Safety Issues
▪ Before beginning any
assembly process, review
safety procedures.
▪ Assembling a computer is
not an inherently dangerous
job, but being aware of
safety procedures is a good
starting point.
▪ In addition to the safety
procedures, there are safety
concerns with leaving the
computer plugged in while
working inside it.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 2
ESD Precautions
▪ Electrostatic Discharge (ESD) is
more commonly referred to as
static electricity.
▪ ESD is probably the greatest
problem when a user is
unwrapping newly purchased
computer parts and components
while preparing to assemble the
computer.
▪ Just because a discharge cannot
be felt does not mean it cannot
harm a computer component.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 3
 Creating a Computer Inventory

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 4
 Importance of an Inventory
▪ When building a computer
from scratch, it is important
to document all of the
components and parts that
are purchased.
▪ Make sure the specifics
about installation and
maintenance requirements
are saved, so that warranties
will be valid.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 5
Inventory Checklist
▪ It is important to save all the
documentation that comes
with the components.
▪ Store original documentation
in zip lock type bags and
paper work in 3-ring binders.
▪ Keep a notebook in which
websites can be referenced
with useful information
related to components such
as devices drivers, and so
on.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 6
 Open the Case
▪ Prepare the workspace before opening the computer
case:
Adequate lighting
Good ventilation
Comfortable room temperature
Workbench accessible from all sides
Avoid cluttering workbench
An antistatic mat on the table
Small containers to hold screws and other small parts
▪ There are different methods for opening cases. To
learn how, consult the user manual or manufacturer's
website.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 7
 Install the Power Supply
Power supply installation steps include the following:
1. Insert the power supply into the case
2. Align the holes in the power supply with the holes in
the case
3. Secure the power
supply to the case
using the proper
screws

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 8
 Preparing the Motherboard for Installation

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 9
Motherboard Location Map
▪ A motherboard location map
shows where the hardware and
major components are located
on the motherboard.
▪ Typically, everything listed in
the specifications section of the
motherboard manual is
depicted and labeled on the
location map.
▪ The main memory is
subdivided into slots, and the
slots are identified and
numbered in sequence DIMM
bank 1, DIMM bank 2, and
DIMM bank 3.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 10
Motherboard Configuration
▪ Configuring the motherboard
typically means the taking
the following steps:
▪ Installing the CPU, installing
the heat sink and fan,
installing RAM, connecting
the power supply cables to
the motherboard power
connectors, connecting
miscellaneous connectors to
the correct switches and
status lights, and setting the
system BIOS.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 11
 Motherboard Configuration
▪ Location maps allow the correct configuration of the
motherboard for the case controls and monitor lights
on the front case panel .
▪ For the disk controllers, always remember that a
colored stripe on the data cable is pin 1.
▪ The BIOS interface can be keyboard driven, or it can
be graphical and mouse driven.
▪ When drives are replaced, memory upgraded, or
adapter boards added, the BIOS setup will need to be
updated to reflect the configuration changes and
saved to the CMOS chip.
▪ The motherboard must be configured for the
frequency of the installed processor.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 12
Motherboard Jumpers
▪ A jumper is a pair of prongs
that are electrical contact points
set into the computer
motherboard or an adapter
card.
▪ When setting a jumper, place a
plug on the prongs that
completes or closes the
contact.
▪ Closing or opening the circuits
establishes logic levels to
select functions for the
operation of the board.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 13
 Motherboard Jumpers
▪ Typically, motherboard jumpers are configured by using a
jumper to bridge a pair of pins that are to be connected
together (to complete a circuit) on the board.
▪ Removing or inserting jumpers on a set of pins will enable
or clear a given option, as specified in the motherboard
manual.
▪ There are several additional jumper settings that may have
to be set along with the general motherboard
configurations:
–BIOS Recovery
–Clear CMOS
–Password Clear
–BIOS Setup Access
–Processor Voltage
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 14
 Attach Components to the Motherboard
▪ As part of an upgrade or repair, a technician may need
to attach components to the motherboard, and then
install the motherboard.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 15
 CPU on Motherboard
▪ The CPU and motherboard are sensitive to electrostatic
discharge so use a grounded antistatic mat and wear an
antistatic wrist strap. CAUTION: When handling a CPU,
do not touch the CPU contacts.
▪ The CPU is secured to the socket on the motherboard
with a locking assembly.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 16
 Installing the CPU
1. Turn over the chip and inspect the pins to make sure none are
damaged (bent or broken). All pins should stick straight out.
2. Align pin 1 on the chip with pin 1 on the socket for a correct
installation.
3. Open the ZIF socket. Shift the lever slightly away from the
socket, from its default closed, level position and raise it to the
open, vertical position.
4. Align pin 1 according to the orientation that was determined in
Step 2. Insert the processor chip into the socket so that all of
the pins slide into the matching holes.
5. Double-check to make sure that there is no gap between the
bottom of the CPU chip and the socket. If there is none, then
the processor chip is properly inserted.
6. Secure the installed chip, push the lever gently back down to
the closed, level position.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 17
 Installing the CPU
▪ Most motherboards are flexible enough to
handle a variety of CPUs, but most CPUs are
very particular about the amount of voltage
they can handle.
▪ After installing the CPU, it is important to make
sure that the right voltage is present for the
proper performance of the processor.
▪ If the proper voltage is not set, total damage to
the system could occur, or the whole system
will never operate correctly.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 18
 Thermal Compound
▪ Thermal compound helps to keep the CPU cool.
▪ To install a used CPU, clean it and the base of the heat
sink with isopropyl alcohol to remove the old thermal
compound.
▪ Follow manufacturer’s
recommendations
about applying the
thermal compound.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 19
 Heat Sink/Fan Assembly
▪ The Heat Sink/Fan Assembly is a two-part cooling
device.
▪ The heat sink draws heat
away from the CPU.
▪ The fan moves the heat
away from the heat sink.
▪ The heat sink/fan
assembly usually has a 3-
pin power connector.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 20
 Install CPU and Heat Sink/Fan Assembly
1. Align the CPU so that the Connection 1 indicator is lined up with Pin 1 on
the CPU socket.
2. Place the CPU gently into the socket.
3. Close the CPU load plate and secure it by closing the load lever and
moving it under the load lever retention tab.
4. Apply a small amount of thermal compound to the CPU and spread it
evenly. Follow the application instructions provided by the manufacturer.
5. Line up the heat sink/fan assembly retainers to the holes on the
motherboard.
6. Place the heat sink/fan assembly onto the CPU socket, being careful not
to pinch the CPU fan wires.
7. Tighten the heat sink/fan assembly retainers to secure the assembly in
place.
8. Connect the heat sink/fan assembly power cable to the header on the
motherboard.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 21
 Install RAM
▪ RAM provides temporary data storage for the CPU
while the computer is operating.
▪ RAM should be installed in the motherboard before
the motherboard is placed in the computer case.
▪ RAM installation steps:
1. Align the notches on the RAM module to the keys in the slot
and press down until the side tabs click into place.
2. Make sure that the side tabs have locked the RAM module
and visually check for exposed contacts.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 22
 The Motherboard
▪ The motherboard is now ready to install in the
computer case.
▪ Plastic and metal standoffs are used to mount the
motherboard and to prevent it from touching the metal
portions of the case.
▪ Install only the standoffs that align with the holes in the
motherboard.
▪ Installing any additional standoffs may prevent the
motherboard from being seated properly in the
computer case.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 23
 Install Motherboard
1. Install standoffs in the computer
case.
2. Align the I/O connectors on the
back of the motherboard with the
openings in the back of the
case.
3. Align the screw holes of the
motherboard with the standoffs.
4. Insert all of the motherboard
screws.
5. Tighten all of the motherboard
ITE PC v4.0
screws.
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 24
 Install Internal Drives
▪ Drives that are installed in internal bays are called
internal drives.
▪ A hard disk drive (HDD) is an example of an internal
drive.
▪ HDD installation steps:
1. Position the HDD so that it aligns
with the 3.5-inch drive bay.
2. Insert the HDD into the drive bay so
that the screw holes in the drive line
up with the screw holes in the case.
3. Secure the HDD to the case using
the proper screws.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 25
 Install Drives in External Bays
▪ Drives, such as optical drives (CD
and DVD) and floppy drives, are
installed in drive bays that are
accessed from the front of the case.
▪ Optical drives and floppy drives
store data on removable media.
▪ Drives in external bays allow
access to the media without
opening the case.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 26
 Install Optical Drive
▪ An optical drive is a storage device that reads and
writes information to CDs or DVDs.
▪ Optical drive installation steps:
1. Position the optical drive to align with the 5.25 inch drive bay.
2. Insert the optical drive into the drive bay so that the optical
drive screw holes align with the screw holes in the case.
3. Secure the optical drive to the case using the proper screws.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 27
 Install Floppy Drive
▪ A floppy disk drive (FDD) is a storage device that reads
and writes information to a floppy disk.
▪ FDD installation steps:
1. Position the FDD so that it aligns with the 3.5 inch drive bay.
2. Insert the FDD into the drive bay so that the FDD screw holes
align with the screw holes in the case.
3. Secure the FDD to the case using the proper screws.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 28
 Install Adapter Cards
▪ Adapter cards are installed to add functionality to a
computer.
▪ Adapter cards must be compatible with the expansion
slot.
▪ Some adapter cards:
PCIe x1 NIC
PCI Wireless NIC
PCIe x16 video adapter card

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 29
 Install the Network Interface Card (NIC)
▪ A NIC enables a computer to connect to a network.
▪ NICs use PCI and PCIe expansion slots on the
motherboard.
▪ NIC installation steps:
1. Align the NIC to the appropriate slot on
the motherboard.
2. Press down gently on the NIC until the
card is seated.
3. Secure the NIC PC mounting bracket to
the case with the appropriate screw.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 30
 Install the Wireless NIC
▪ A wireless NIC enables a computer
to connect to a wireless network.
▪ Some wireless NICs are installed
externally with a USB connector.
▪ Wireless NIC installation steps:
1. Align the wireless NIC to the appropriate expansion slot on
the motherboard.
2. Press down gently on the wireless NIC until the card is
fully seated.
3. Secure the mounting bracket to the case with the appropriate
screw.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 31
 Install the Video Adapter Card
▪ A video adapter card is the interface between a
computer and a display monitor.
▪ An upgraded video adapter card can provide better
graphic capabilities for games and graphic programs.
▪ Video adapter card installation steps:
1. Align the video adapter card to the appropriate expansion
slot on the motherboard.
2. Press down gently on the video
adapter card until the card is fully
seated.
3. Secure the video adapter card
PC mounting bracket to the case
with the appropriate screw.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 32
 Connect Internal Cables
▪ Power cables are used to distribute
electricity from the power supply to
the motherboard and other
components.
▪ Data cables transmit data between
the motherboard and storage devices,
such as hard drives.
▪ Additional cables connect the buttons
and link lights on the front of the
computer case to the motherboard.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 33
 Connect Power Cables
Motherboard Power Connections
▪ The Advanced Technology Extended
(ATX) main power connector has either
20 or 24 pins.

▪ The power supply may also have a 4-pin

or 6-pin Auxiliary (AUX) power connector
that connects to the motherboard.
▪ A 20-pin connector will work in a
motherboard with a 24-pin socket.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 34
 Connect Power Cables
▪ SATA Power Connectors use a 15-pin
connector to connect to hard disk drives,
optical drives, or any devices that have a SATA
power socket. SATA
▪ Molex Power Connectors are used by hard
disk drives and optical drives that do not have
SATA power sockets.
Berg ▪ CAUTION: Do not use a Molex connector and
a SATA power connector on the same drive at
the same time.
▪ 4-pin Berg Power Connector supplies power to Molex
a floppy drive.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 35
 Power Connector Installation Steps
1. Plug the SATA power connector into the HDD.
2. Plug the Molex power connector into the optical drive.
3. Plug the 4-pin Berg power connector into the FDD.
4. Connect the 3-pin fan power connector into the
appropriate fan header on the motherboard,
according to the motherboard manual.
5. Plug the additional cables from the case into the
appropriate connectors according to the motherboard
manual.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 36
 PATA Cables
▪ Drives connect to the motherboard using data cables.
Types of data cables are PATA, SATA, and floppy disk.
▪ The PATA cable (sometimes called a ribbon cable) is
wide and flat and can have either 40 or 80 conductors.
A PATA cable usually has three 40-pin connectors.
If multiple hard drives are installed, the master drive will
connect to the end connector. The slave drive will connect to
the middle connector.
▪ Many motherboards have two PATA cable sockets,
which provides support for a maximum of four PATA
drives.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 37
 SATA Cables
▪ The SATA data cable has a 7-pin connector.
One end of the cable is connected to the motherboard.
The other end is connected to any drive that has a SATA data
connector.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 38
 Floppy Drive Cables
▪ The floppy drive data cable has a 34-pin connector and
it has a stripe to denote the location of pin 1.
One connector at the end of the cable connects to the
motherboard. The other two connectors connect to drives.
If multiple floppy drives are installed, the A: drive will connect to
the end connector. The B: drive will connect to the middle
connector.

▪ Motherboards have one floppy drive controller which

provides support for a maximum of two floppy drives.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 39
 Install Data Cables
1. Plug the motherboard end of the PATA cable into the
motherboard socket.
2. Plug the connector at the far end of the PATA cable
into the optical drive.
3. Plug one end of the SATA cable into the motherboard
socket.
4. Plug the other end of the SATA cable into the HDD.
5. Plug the motherboard end of the FDD cable into the
motherboard socket.
6. Plug the connector at the far end of the FDD cable
into the floppy drive.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 40
 Re-attach Panels, Connect External Cables
▪ Now that all the internal components have been
installed and connected to the motherboard and power
supply, the side panels are re-attached to the computer
case.
▪ The next step is to connect the cables for all computer
peripherals and the power cable.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 41
 Re-attach Side Panels
▪ Most computer cases have two panels, one on each
side.
▪ Once the cover is in place, make sure that it is secured
at all screw locations.
▪ Refer to the documentation or manufacturer’s website if
you are unsure about how to remove or replace your
computer case.
▪ CAUTION: Handle case parts
with care. Some computer case
covers have sharp or jagged
edges.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 42
 Connect External Cables
▪ After the case panels have been re-attached, connect
the external cables to the back of the computer.
▪ External cable connections include:
Monitor USB
Keyboard Power
Mouse Ethernet
▪ CAUTION: When attaching cables, never force a
connection.
▪ NOTE: Plug in the power cable after you have
connected all other cables.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 43
 Connect External Cables
1. Attach the monitor cable to the video port.
2. Secure the cable by tightening the screws on the
connector.
3. Plug the keyboard cable into the PS/2 keyboard
port.
4. Plug the mouse cable into the PS/2 mouse port.
5. Plug the USB cable into a USB port.
6. Plug the network cable into the network port.
7. Connect the wireless antenna to the antenna
connector.
8. Plug the power cable into the power supply.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 44
 Front Panel Connections

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 45
Fitting the Case Together
▪ Once all the components and
parts have been installed in the
case, it is time to complete the PC
assembly process.
▪ Check to make sure that all of the
pin 1 indicators on the cables
match up with all of the pin 1
indicators on the sockets and that
connections are snug.
▪ Make sure that all of the screws
are properly tightened.
▪ When securing the case, make
sure no cables or wires are
sticking out or are caught between
the parts of the case.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 46
 Boot Computer for the First Time
▪ The BIOS is a set of instructions stored in a nonvolatile
memory chip.
▪ When the computer is booted, the basic input/output system
(BIOS) will perform a power-on self test (POST) to check on
all of the internal components.

▪ A special key or combination of keys on the keyboard is

used to enter the BIOS setup program.
▪ The BIOS setup program displays information about all of
ITE PC v4.0
the components in the computer.
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 47
 Identify Beep Codes
▪ POST checks to see that all of the hardware in the
computer is operating correctly.
▪ If a device is malfunctioning, an error or a beep code
alerts the technician that there is a problem.
▪ Typically, a single beep denotes that the computer is
functioning properly.
▪ If there is a hardware problem, the computer may emit
a series of beeps.
▪ Each BIOS manufacturer uses different codes to
indicate hardware problems.
▪ Consult the motherboard documentation to view beep
codes for your computer.
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 48
 BIOS Setup
▪ The BIOS contains a setup program used to configure
settings for hardware devices.
▪ The configuration data is saved to a special memory
chip called a complementary metal-oxide
semiconductor (CMOS).
▪ CMOS is maintained by the battery in the computer.
▪ If this battery dies, all BIOS setup configuration data
will be lost.
▪ Replace the battery and reconfigure the BIOS settings.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 49
 BIOS Setup Program
BIOS settings are configured in the BIOS setup program.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 50
 Chapter 3 Summary
Computer Assembly
▪ Installation of all computer components
▪ Connection of all cables
▪ Description of BIOS
▪ Description of POST

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 51
 Instructor Training Discussion
▪ Share and discuss with the other
instructors, your list of any potential
student issues and questions
regarding the Virtual Desktop
activities and labs.

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 52
 Additional Resources
▪ Whatis?com: IT Encyclopedia and Learning Center
http://whatis.com
▪ TechTarget: The Most Targeted IT Media http://techtarget.com
▪ ZDNet: Tech News, Blogs and White Papers for IT Professionals
http://www.zdnet.com
▪ HowStuffWorks: It's Good to Know
http://computer.howstuffworks.com
▪ CNET.com http://www.cnet.com
▪ PC World http://www.pcworld.com
▪ ComputerWorld http://www.computerworld.com
▪ WIRED NEWS http://www.wired.com
▪ eWEEK.com http://www.eweek.com
ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 53
 Q and A

ITE PC v4.0
Chapter 3 © 2007 Cisco Systems, Inc. All rights reserved. Cisco Public 54