LP140WH2

Liquid Crystal Display

Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ◆ ) Final Specification

Title 14.0” HD TFT LCD

Customer SONY SUPPLIER LG Display Co., Ltd.

MODEL *MODEL LP140WH2

Suffix TLL2
*When you obtain standard approval,
please use the above model name without suffix

APPROVED BY SIGNATURE APPROVED BY SIGNATURE

N. J. Seong / Manager
/
REVIEWED BY

/
S. S. Han / Engineer

/ PREPARED BY

C. H. Hwang / Engineer
S. K. Ahn / Engineer

Please return 1 copy for your confirmation with Products Engineering Dept.
your signature and comments. LG Display Co., Ltd

Ver. 1.0 Jul. 16. 2010 1 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

Contents

No ITEM Page
COVER 1

CONTENTS 2

RECORD OF REVISIONS 3

1 GENERAL DESCRIPTION 4

2 ABSOLUTE MAXIMUM RATINGS 5

3 ELECTRICAL SPECIFICATIONS

3-1 ELECTRICAL CHARACTREISTICS 6-7

3-2 INTERFACE CONNECTIONS 8

3-3 LVDS SIGNAL TIMING SPECIFICATION 9-10

3-4 SIGNAL TIMING SPECIFICATIONS 11

3-5 SIGNAL TIMING WAVEFORMS 11

3-6 COLOR INPUT DATA REFERNECE 12

3-7 POWER SEQUENCE 13

4 OPTICAL SFECIFICATIONS 14-16

5 MECHANICAL CHARACTERISTICS 17-19

6 RELIABLITY 20

7 INTERNATIONAL STANDARDS

7-1 SAFETY 21

7-2 EMC 21

7-3 Environment 21

8 PACKING

8-1 DESIGNATION OF LOT MARK 22

8-2 PACKING FORM 22

9 PRECAUTIONS 23-24

Ver. 1.0 Jul. 16. 2010 2 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

RECORD OF REVISIONS

EDID
Revision No Revision Date Page Description
ver
0.0 Apr. 09. 2010 - First Draft (Preliminary Specification) -
1.0 Jul. 16. 2010 - Final Specification -
4, 6 Update the Electrical Characteristics. (Power Consumption)
14 Update Color Coordinates
15 Update Gray Scale

Ver. 1.0 Jul. 16. 2010 3 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

1. General Description
The LP140WH2 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally white mode. This TFT-LCD has 14.0 inches diagonally measured active display area with HD
resolution (1366 horizontal by 768 vertical pixel array). Each pixel is divided into Red, Green and Blue sub-
pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is
determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144
colors. The LP140WH2 has been designed to apply the interface method that enables low power, high
speed, low EMI. The LP140WH2 is intended to support applications where thin thickness, low power are
critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-
pixels, the LP140WH2 characteristics provide an excellent flat display for office automation products such
as Notebook PC.

EEPROM
EEPROM Block
Block
for
forEDID
EDID

EEPROM
EEPROMBlock
Block 1 1366
for
forTcon
TconOperating
Operating
User connector

TFT-LCD Panel

LVDS Timing
TimingControl
Control (HD, GIP, TN)
1port (Tcon)
(Tcon)Block
Block
Min
i-LV 768
DVCC TCLKs DS
40
DVCC, AVDD
Pin

VCC Power Source Driver

Power VGH, VGL, GMA
(Bottom)
Block
Block GIP CLKs, DSC

VOUT_LED
VLED LED LED Backlight Ass’y
LEDDriver
Driver FB1~4
LED_EN
PWM Block
Block

Control & Data Power EDID signal & Power

General Features
Active Screen Size 14.0 inches diagonal
Outline Dimension 322.3(H, typ) × 204.6(V, typ) × 3.6(D,max) [mm] (with Bracket & PCB Board)
Pixel Pitch 0.2265mm × 0.2265 mm
Pixel Format 1366 horiz. by 768 vert. Pixels RGB strip arrangement
Color Depth 6-bit, 262,144 colors
Luminance, White 200 cd/m2
Power Consumption Total 3.5 W(Typ.) Logic : 1.0 W (Typ.@ Mosaic), B/L : 2.5W (Typ.@ VLED 19V )
Weight 320g (Max.)
Display Operating Mode Transmissive mode, normally white
Surface Treatment Glare treatment (3H) of the front Polarizer
RoHS Compliance Yes
BFR / PVC / As Free Yes for all

Ver. 1.0 Jul. 16. 2010 4 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. ABSOLUTE MAXIMUM RATINGS

Values
Parameter Symbol Units Notes
Min Max
Power Input Voltage VCC -0.3 4.0 Vdc at 25 ± 5°C

Operating Temperature TOP 0 50 °C 1

Storage Temperature HST -20 60 °C 1

Operating Ambient Humidity HOP 10 90 %RH 1

Storage Humidity HST 10 90 %RH 1

Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39°C Max, and no condensation of water.

90% 80%

60 60%

Wet Bulb 50
Humidity[(%)RH]

℃]
Temperature [℃ Storage

40 40%

30 Operation
20
20%
10
0
10%

-20 0 10 20 30 40 50 60 70 80

℃]
Dry Bulb Temperature [℃

Ver. 1.0 Jul. 16. 2010 5 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics
The LP140WH2 requires two power inputs. The first logic is employed to power the LCD electronics and to
drive the TFT array and liquid crystal. The second backlight is the input about LED BL with LED Driver.

Table 2. ELECTRICAL CHARACTERISTICS

Values
Parameter Symbol Unit Notes
Min Typ Max
LOGIC :
Power Supply Input Voltage VCC 3.0 3.3 3.6 V 1
Mosaic - 315 365 mA 2
Power Supply Input Current ICC
Black 410 470 mA
Power Consumption PCC 1.0 1.2 W 2
Power Supply Inrush Current ICC_P - - 1500 mA 3
LVDS Impedance ZLVDS 90 100 110 Ω 4
BACKLIGHT : ( with LED Driver)
LED Power Input Voltage VLED 7.0 19.0 21.0 V 5
LED Power Input Current ILED - 130 150 mA
6
LED Power Consumption PLED - 2.5 2.9 W
LED Power Inrush Current ILED_P - - 1000 mA 7
PWM Duty Ratio 5 - 100 % 8
PWM Jitter - 0 - 0.2 % 9
PWM Impedance ZPWM 20 40 60 kΩ
PWM Frequency FPWM 200 - 1000 Hz 10
PWM High Level Voltage VPWM_H 3.0 - 3.6 V
PWM Low Level Voltage VPWM_L 0 - 0.3 V
LED_EN Impedance ZPWM 20 40 60 kΩ
LED_EN High Voltage VLED_EN_H 3.0 - 3.6 V
LED_EN Low Voltage VLED_EN_L 0 - 0.3 V
Life Time 12,000 - - Hrs 11

Ver. 1.0 Jul. 16. 2010 6 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

Note)
1. The measuring position is the connector of LCM and the test conditions are under 25℃, fv = 60Hz,
Black pattern.
2. The specified Icc current and power consumption are under the Vcc = 3.3V , 25℃, fv = 60Hz condition.

Mosaic Pattern
3. This Spec. is the max load condition for the cable impedance designing.
4. The below figures are the measuring Vcc condition and the Vcc control block LGD used.
The Vcc condition is same as the minimum of T1 at Power on sequence.

3.3V
Rising time
Vcc 90%

0V 10%
0.5ms

5. This impedance value is needed for proper display and measured form LVDS Tx to the mating connector.
6. The measuring position is the connector of LCM and the test conditions are under 25℃.
7. The current and power consumption with LED Driver are under the Vled = 12.0V , 25℃, Dimming of
Max luminance and White pattern with the normal frame frequency operated(60Hz).
8. The below figures are the measuring Vled condition 12.0V
and the Vled control block LGD used. Rising time 90%
VLED control block is same with Vcc control block. VLED

0V 10%
0.5ms

9. The operation of LED Driver below minimum dimming ratio may cause flickering or reliability issue.
10. If Jitter of PWM is bigger than maximum, it may induce flickering.
11. This Spec. is not effective at 100% dimming ratio as an exception because it has DC level equivalent
to 0Hz. In spite of acceptable range as defined, the PWM Frequency should be fixed and stable for
more consistent brightness control at any specific level desired.
12. The life time is determined as the time at which brightness of LCD is 50% compare to that of minimum
value specified in table 7. under general user condition.

Ver. 1.0 Jul. 16. 2010 7 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

3-2. Interface Connections

This LCD employs two interface connections, a 40 pin connector used for the module electronics interface and
the other connector used for the integral backlight system.

Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)

Pin Symbol Description Notes

1 NC No Connection [Interface Chip]
2 VCC LCD Logic and driver power (3.3V Typ.) 1. LCD :
3 VCC LCD Logic and driver power (3.3V Typ.) SiW, SW0617(LCD Controller)
4 V EEDID DDC Power (3.3V) Including LVDS Receiver.
5 NC No Connection 2. System : SiW LVDSRx or equivalent
6 Clk EEDID DDC Clock * Pin to Pin compatible with LVDS
7 DATA EEDID DDC Data
[Connector]
8 ORX0- Negative LVDS differential data input
UJU IS050-L40B-C10
9 ORX0+ Positive LVDS differential data input
LSMtron GT05Q-40S-H10 or equivalent
10 GND High Speed Ground
11 ORX1- Negative LVDS differential data input
[Mating Connector]
12 ORX1+ Positive LVDS differential data input 20345-#40E-## series or equivalent
13 GND High Speed Ground
14 ORX2- Negative LVDS differential data input [Connector pin arrangement]
15 ORX2+ Positive LVDS differential data input
16 GND High Speed Ground 40 1
17 ORXC- Negative LVDS differential clock input
18 ORXC+ Positive LVDS differential clock input
19 NC No Connection
20 NC No Connection [LCD Module Rear View]
21 NC No Connection
19 GND High Speed Ground
23 NC No Connection
24 NC No Connection
19 GND High Speed Ground
26 NC No Connection
27 NC No Connection
19 GND High Speed Ground
29 NC No Connection
30 NC No Connection
31 GND LED Backlight Ground
32 GND LED Backlight Ground
33 GND LED Backlight Ground
34 NC No Connection
35 PWM System PWM Signal input for dimming
36 LED_EN LED Backlight On/Off
37 NC No Connection
38 VLED LED Backlight Power (7V-21V)
39 VLED LED Backlight Power (7V-21V)
40 VLED LED Backlight Power (7V-21V)

Ver. 1.0 Jul. 16. 2010 8 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

3-3. LVDS Signal Timing Specifications

3-3-1. DC Specification

VDD=1.8V

Description Symbol Min Typ Max Unit Notes

LVDS Differential Voltage |VID| 100 - 600 mV -
LVDS Common mode Voltage VCM |VID| /2 1.2 VDD- |VID|/2 V -
LVDS Input Voltage Range VIN 0.3 - VDD V -

3-3-2. AC Specification

Description Symbol Min Max Unit Notes

85MHz > Fclk ≥
tSKEW - 400 + 400 ps
65MHz
LVDS Clock to Data Skew Margin
65MHz > Fclk ≥
tSKEW - 600 + 600 ps
25MHz
LVDS Clock to Clock Skew Margin (Even
tSKEW_EO - 1/7 + 1/7 Tclk -
to Odd)
Maximum deviation
FDEV - ±3 % -
of input clock frequency during SSC
Maximum modulation frequency
FMOD - 200 KHz -
of input clock during SSC

Ver. 1.0 Jul. 16. 2010 9 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

< Clock skew margin between channel >

Freq.

Fmax
Fcenter * FDEV
Fcenter

Fmin

1
FMOD

Time

< Spread Spectrum >

3-3-3. Data Format
1) LVDS 1 Port

RCLK+

RA+/- R3 R2 R1 R0 G0 R5 R4 R3 R2 R1 R0 G0 R5 R4

RB+/- G4 G3 G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 B0 G5

RC+/- B5 B4 B3 B2 DE VSYNC HSYNC B5 B4 B3 B2 DE VSYNC HSYNC

RD+/- G7 G6 R7 R6 X B7 B6 G7 G6 R7 R6 X B7 B6

Previous (N-1)th Cycle Current(Nth) Cycle Next(N+1)th Cycle

< LVDS Data Format >

Ver. 1.0 Jul. 16. 2010 10 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

3-4. Signal Timing Specifications

This is the signal timing required at the input of the User connector. All of the interface signal timing should be
satisfied with the following specifications and specifications of LVDS Tx/Rx for its proper operation.
Table 4. TIMING TABLE

ITEM Symbol Min Typ Max Unit Note

DCLK Frequency fCLK - 72.0 - MHz

Period tHP 1470 1516 1586

Hsync Width tWH 24 32 40 tCLK

Width-Active tWHA 1366 1366 1366

Period tVP 779 790 801

Vsync
Width tWV 2 5 8 tHP

Width-Active tWVA 768 768 768

Horizontal back porch tHBP 56 70 124

tCLK
Data Horizontal front porch tHFP 24 48 48
Enable Vertical back porch tVBP 8 14 20
tHP
Vertical front porch tVFP 1 3 5

Condition : VCC =3.3V

3-5. Signal Timing Waveforms
High: 0.7VCC
Data Enable, Hsync, Vsync
Low: 0.3VCC

tCLK
DCLK 0.5 Vcc

tHP
Hsync t
WH

tHBP tWHA tHFP

Data Enable
tVP
tWV
Vsync tVFP
tVBP tWVA

Data Enable

Ver. 1.0 Jul. 16. 2010 11 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

3-6. Color Input Data Reference

The brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the
color ; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.

Table 5. COLOR DATA REFERENCE

Input Color Data
RED GREEN BLUE
Color
MSB LSB MSB LSB MSB LSB
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

Basic Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Color Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1

Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

RED (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0

RED … … … …

RED (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0

GREEN ... … … …

GREEN (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0

GREEN (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

BLUE (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

BLUE (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

BLUE … … … …

BLUE (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0

BLUE (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

Ver. 1.0 Jul. 16. 2010 12 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

3-7. Power Sequence

90% 90%
Power Supply Input
VCC
0V 10% 10%

T3 T7 T4
T1 T2 Valid Data
Interface Signal, Vi
LVDS
0V

T5 3.0V 3.0V T6
LED on/off control Signal
0V (Off)
LED_EN
T9 T10

Dimming control signal Valid Data

Of LED BL 0V (Low)
PWM
T8 T11

90% 90%
LED input Voltage
VLED 0V 10% T12 T13 10%

Table 6. POWER SEQUENCE TABLE

Logic Value LED Value
Units Units
Parameter Min. Typ. Max. Parameter Min. Typ. Max.
T1 0.5 - 10 ms T8 10 - - ms
T2 0 - 50 ms T9 10 - - ms
T3 0 - 50 ms T10 10 - - ms
T4 500 - - ms T11 10 - - ms
T5 200 - - ms T12 0.5 - - ms
T6 200 - - ms T13 0.5 - 5000 ms
T7 0.5 - 10 ms

Note)
1. Do not insert the mating cable when system turn on.
2. Valid Data have to meet “3-3. LVDS Signal Timing Specifications”
3. LVDS, LED_EN and PWM need to be on pull-down condition on invalid status.
4. LGD recommend the rising sequence of VLED after the Vcc and valid status of LVDS turn on.

Ver. 1.0 Jul. 16. 2010 13 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 20 minutes in
a dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface
at a viewing angle of Φ and Θ equal to 0°.
FIG. 1 presents additional information concerning the measurement equipment and method.

FIG. 1 Optical Characteristic Measurement Equipment and Method

LCD Module Equipment

Optical Stage(x,y)

±50mm
500mm±

Table 7. OPTICAL CHARACTERISTICS

Ta=25°C, VCC=3.3V, fV=60Hz, fCLK= 72.0MHz
Values
Parameter Symbol Units Notes
Min Typ Max
Contrast Ratio CR 400 500 - 1
Surface Luminance, white LWH 170 200 - cd/m2 2
Luminance Variation δ WHITE - 1.4 1.6 % 3
Response Time TrR + TrD - 16 25 ms 4
Color Coordinates
RED RX 0.556 0.586 0.616
RY 0.318 0.348 0.378
GREEN GX 0.308 0.338 0.368
GY 0.524 0.554 0.584
BLUE BX 0.126 0.156 0.186
BY 0.107 0.137 0.167
WHITE WX 0.283 0.313 0.343
WY 0.299 0.329 0.359
Viewing Angle 5
x axis, right(Φ=0°) Θr 40 - - degree
x axis, left (Φ=180°) Θl 40 - - degree
y axis, up (Φ=90°) Θu 10 - - degree
y axis, down (Φ=270°) Θd 30 - - degree
Gray Scale 6
Color Gamut C/G - 45 - %

Ver. 1.0 Jul. 16. 2010 14 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

Note)
1. Contrast Ratio(CR) is defined mathematically as

Surface Luminance with all white pixels

Contrast Ratio =
Surface Luminance with all black pixels

2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with
all pixels displaying white. For more information see FIG 1.

LWH = Average(L1,L2, … L5)

3. The variation in surface luminance , The panel total variation (δ WHITE) is determined by measuring LN
at each test position 1 through 13 and then defined as following numerical formula.
For more information see FIG 2.

Maximum(L1,L2, … L13) - Minimum(L1,L2, … L13)

δ WHITE( = * 100(%)
Maximum(L1,L2, … L13)

4. Response time is the time required for the display to transition from white to black (rise time, TrR) and
from black to white(Decay Time, TrD). For additional information see FIG 3.

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined
for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the
LCD surface. For more information see FIG 4.

6. Gray scale specification * fV = 60Hz

Gray Level Luminance [%] (Typ)

L0 0.0
L7 0.8
L15 4.25
L23 10.9
L31 21.0
L39 34.8
L47 52.5
L55 74.2
L63 100.0

Ver. 1.0 Jul. 16. 2010 15 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

FIG. 2 Luminance
<Measuring point for Average Luminance & measuring point for Luminance variation>
H

10mm A

6 7 8 10mm
2 3
B H,V : ACTIVE AREA
V A : H/4 mm
9 1 10
B : V/4 mm
POINTS: 13 POINTS
4 5 13
11 12

FIG. 3 Response Time Active Area

The response time is defined as the following figure and shall be measured by switching the input signal
for “black” and “white”.
TrR TrD
%
100
90

Optical
Response
10
0 white white
black

FIG. 4 Viewing angle Normal

Eye Y
<Dimension of viewing angle range> φ = 90 ° , Up

φ = 180 ° ,
Left θ

φ = 0° ,
Right

φ = 270 ° ,
Down

Ver. 1.0 Jul. 16. 2010 16 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LP140WH2. In addition the figures
in the next page are detailed mechanical drawing of the LCD.

Horizontal (A) 322.3 ± 0.5mm

Outline Dimension Vertical (B) 204.6 ± 0.5mm

Thickness 3.6mm (max)

Horizontal 313.40 ± 0.5mm

Bezel Area
Vertical 177.45 ± 0.5mm

Horizontal 309.40 mm
Active Display Area
Vertical 173.95 mm

Weight 320g (Max.)

Surface Treatment Hard Coating(3H), Glare treatment of the front polarizer

<Outline Dimension : With Bracket and PCB Board>

Ver. 1.0 Jul. 16. 2010 17 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

<FRONT VIEW> Note) Unit:[mm], General tolerance: ± 0.5mm

Ver. 1.0 Jul. 16. 2010 18 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

<REAR VIEW> Note) Unit:[mm], General tolerance: ± 0.5mm

Ver. 1.0 Jul. 16. 2010 19 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

6. Reliability

Environment test condition

No. Test Item Conditions

1 High temperature storage test Ta= 60°C, 240h
2 Low temperature storage test Ta= -20°C, 240h
3 High temperature operation test Ta= 50°C, 50%RH, 240h
4 Low temperature operation test Ta= 0°C, 240h
5 Vibration test (non-operating) Sine wave, 5 ~ 150Hz, 1.5G, 0.37oct/min
3 axis, 30min/axis
6 Shock test (non-operating) - No functional or cosmetic defects following a shock
to all 6 sides delivering at least 180 G in a half sine
pulse no longer than 2 ms to the display module
- No functional defects following a shock delivering
at least 200 g in a half sine pulse no longer than 2
ms to each of 6 sides. Each of the 6 sides will be
shock tested with one each display, for a total of 6
displays
7 Altitude operating 0 ~ 10,000 feet (3,048m) 24Hr
storage / shipment 0 ~ 40,000 feet (12,192m) 24Hr

{ Result Evaluation Criteria }

There should be no change which might affect the practical display function when the display quality
test is conducted under normal operating condition.

Ver. 1.0 Jul. 16. 2010 20 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

7. International Standards

7-1. Safety
a) UL 60950-1, Second Edition, Underwriters Laboratories Inc.
Information Technology Equipment - Safety - Part 1 : General Requirements.
b) CAN/CSA C22.2 No.60950-1-07, Second Edition, Canadian Standards Association.
Information Technology Equipment - Safety - Part 1 : General Requirements.
c) EN 60950-1:2006 + A11:2009, European Committee for Electrotechnical Standardization (CENELEC).
Information Technology Equipment - Safety - Part 1 : General Requirements.
d) IEC 60950-1:2005, Second Edition, The International Electrotechnical Commission (IEC).
Information Technology Equipment - Safety - Part 1 : General Requirements.

7-2. EMC

a) ANSI C63.4 “American National Standard for Methods of Measurement of Radio-Noise

Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.”
American National Standards Institute (ANSI), 2003.
b) CISPR 22 “Information technology equipment – Radio disturbance characteristics – Limit and
methods of measurement." International Special Committee on Radio Interference
(CISPR), 2005.
c) CISPR 13 “Sound and television broadcast receivers and associated equipment – Radio disturbance
characteristics – Limits and method of measurement." International Special Committee on Radio
Interference (CISPR), 2006.

7-3. Environment
a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003

Ver. 1.0 Jul. 16. 2010 21 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

8. Packing
8-1. Designation of Lot Mark
a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010

Mark 1 2 3 4 5 6 7 8 9 0

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Mark 1 2 3 4 5 6 7 8 9 A B C

b) Location of Lot Mark

Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one box : 30pcs

b) Box Size : 473mm X 364mm X 338mm

Ver. 1.0 Jul. 16. 2010 22 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

9. PRECAUTIONS

Please pay attention to the followings when you use this TFT LCD module.

9-1. MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
(10) When handling the LCD module, it needs to handle with care not to give mechanical stress to the PCB
and Mounting Hole area.”

9-2. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=± 200mV(Over and under shoot voltage)

(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.

Ver. 1.0 Jul. 16. 2010 23 / 24

 LP140WH2
Liquid Crystal Display
Product Specification

9-3. ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.

9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied
to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to
remain on the polarizer.
Please carefully peel off the protection film without rubbing it against the polarizer.
(3) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the polarizer after the protection film is peeled off.
(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like chamois
soaked with normal-hexane.

Ver. 1.0 Jul. 16. 2010 24 / 24