Safety of amusement rides and amusement devices - Part 3: Requirements for
inspection during design, manufacture, operation and use
Sicherheit von Fahrgeschäften und Vergnügungseinrichtungen - Teil 3: Anforderungen
iTeh Standards an die Überprüfung während der Konstruktion, Bemessung, Herstellung, Betrieb und Gebrauch (https://standards.iteh.ai) Sécurité des manèges et des dispositifs de divertissement - Partie 3: Exigences relatives Document à l'inspection pendant la conception, Preview la fabrication et le fonctionnement
Ta slovenski standard je istoveten SIST
z: EN 13814-3:2019 prEN 13814-3 https://standards.iteh.ai/catalog/standards/sist/4b82adb1-987c-483e-96dc-c9d73a01456f/sist-en-13814-3-2019
ICS: 97.200.40 ,JULãþD Playgrounds
oSIST prEN 13814-3:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno. oSIST prEN 13814-3:2016
NORME EUROPÉENNE prEN 13814-3 EUROPÄISCHE NORM January 2016
ICS 91.040.99; 97.200.99 Will supersede EN 13814:2004
English Version
Safety of amusement rides and amusement devices - Part
3: Requirements for inspection during design, manufacture, operation and use Sécurité des manèges et des dispositifs de Sicherheit von Fahrgeschäften und divertissement - Partie 3: Exigences relatives à Vergnügungseinrichtungen - Teil 3: Anforderungen an l'inspection pendant la conception, la fabrication et le die Überprüfung während der Konstruktion, fonctionnement Bemessung, Herstellung, Betrieb und Gebrauch
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 152.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
iTeh Standards This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
(https://standards.iteh.ai) Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Document Preview Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
SIST Recipients of this draft are invited to submit, with EN their 13814-3:2019 comments, notification of any relevant patent rights of which they are https://standards.iteh.ai/catalog/standards/sist/4b82adb1-987c-483e-96dc-c9d73a01456f/sist-en-13814-3-2019 aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
European foreword....................................................................................................................................................... 3 1 Scope .................................................................................................................................................................... 4 2 Normative references .................................................................................................................................... 4 3 Terms and definitions ................................................................................................................................... 4 4 Requirements ................................................................................................................................................... 4 4.1 Initial Approval – Procedures ..................................................................................................................... 4 4.1.1 General ................................................................................................................................................................ 4 4.1.2 Review of design documents ....................................................................................................................... 5 4.1.3 Inspection of manufacturing process ...................................................................................................... 5 4.2 Pre-use inspection and review – Procedures........................................................................................ 7 4.3 In-service inspection (periodical test) .................................................................................................... 7 4.3.1 General ................................................................................................................................................................ 7 4.3.2 Inspection process .......................................................................................................................................... 7 4.3.3 Electrical equipment ...................................................................................................................................... 9 4.3.4 Reports ................................................................................................................................................................ 9 Bibliography ................................................................................................................................................................. 10
iTeh Standards (https://standards.iteh.ai) Document Preview SIST EN 13814-3:2019 https://standards.iteh.ai/catalog/standards/sist/4b82adb1-987c-483e-96dc-c9d73a01456f/sist-en-13814-3-2019
2 oSIST prEN 13814-3:2016
prEN 13814-3:2016 (E)
European foreword
This document (prEN 13814-3:2016) has been prepared by Technical Committee CEN/TC 152 “Fairground and amusement park machinery and structures - Safety”, the secretariat of which is held by UNI. This document is currently submitted to the CEN Enquiry. This document, together with its first and second parts, will supersede EN 13814: 2004. EN 13814 consists of the following parts, under the general title “Safety of amusement rides and amusement devices” — Part 1: Design and Manufacture
— Part 2: Operation, Maintenance and Use
— Part 3: Requirements for inspection during design, manufacture, operation and use
iTeh Standards (https://standards.iteh.ai) Document Preview SIST EN 13814-3:2019 https://standards.iteh.ai/catalog/standards/sist/4b82adb1-987c-483e-96dc-c9d73a01456f/sist-en-13814-3-2019
3 oSIST prEN 13814-3:2016
prEN 13814-3:2016 (E)
1 Scope This part of EN 13814 defines requirements for the necessary inspections, in accordance with ISO/IEC 17020, of amusement devices designed, manufactured, operated and used according to prEN 13814-1:2016 and prEN 13814-2:2016.
2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. prEN 13814-1:2016, Safety of amusement rides and amusement devices — Part 1: Design and manufacture
prEN 13814-2:2016, Safety of amusement rides and amusement devices — Part 2: Operation, Maintenance and Use
EN 60204-1, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
(IEC 60204-1)
EN ISO 9712, Non-destructive testing — Qualification and certification of NDT personnel (ISO 9712)
EN ISO/IEC 17020, Conformity assessment — Requirements for the operation of various types of bodies performing inspection (ISO/IEC 17020) iTeh Standards CEN/TR 152xxx, Minimum manufacturing quality recommendations for amusement ride components
3 Terms and definitions (https://standards.iteh.ai)
Document For the purposes of this document, Preview the terms and definitions given in prEN 13814-1:2016 and prEN 13814-2:2016 apply. SIST EN 13814-3:2019 4https://standards.iteh.ai/catalog/standards/sist/4b82adb1-987c-483e-96dc-c9d73a01456f/sist-en-13814-3-2019 Requirements 4.1 Initial Approval – Procedures 4.1.1 General
The initial approval of any amusement device consists of review, inspections and tests to be carried out as follows. The inspection body performing the initial approval shall operate in accordance with EN ISO/IEC 17020. All safety-relevant design documents as well as the completed amusement device shall be subjected to review and inspection. After a successful inspection, a document confirming compliance with this standard may be issued. The results of the various reviews, inspections and tests shall become an integral part of the device log. The initial approval of the amusement device shall comprise: a) Design review;
