Scribd
Upload
17 views

Engineering_Drawing_Assignments

Uploaded by

rodneymufute
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
17 views

Engineering_Drawing_Assignments

Uploaded by

rodneymufute
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Mutare Polytechnic

ENGINEERING DIVISION
AUTOMOTIVE ENGINEERING DRAWING
2022 Assignments
Assignment one

1. (a) Describe the term Engineering Drawing.(2)

(B) Name 3 types of Engineering Drawing scales giving an example of each. (6)

(c) State the dimensions of thick and thin lines in Engineering Drawing. (2)

2. List 5 drawing instruments and state the purpose of each. Include the diagram of each in
your explanation. (20)
3. State 5 'A' series engineering drawing papers and their dimensions.(10)
4. List 5 Engineering Drawing line types and explain the application of each. Include a
diagram your explanation. (20)
5. List 5 types of soft and hard pencils respectively. (10)
6. Given a line 120mm long, divide it into 3 parts using the ratio of 4:5:3.show all
construction work. (10)
7. Construct the following angles with the use of a compass and straight edge only.

i) 22,5 ii) 60 iii) 45 iv) 75 v) 90 vi) 15 vii) 30 Viii) 180 ix ) 7.5 X) 150
(10)

DUE DATE 20/05/2022


Assignment Two

1. (a) Construct a perpendicular line at the middle of a line of length 90mm. (5)
(b) Bisect an angle of 45° .clearly ALL show construction lines. (5)
(c) Draw a circle and label all its parts (5)
(d) Demonstrate how an arc is blended to a straight line (5)
(e) Show how the centre of an arc is found (5)

2. (A) Construct an octagon given the length of one side of as 50mm. (10)

(b) State 5 types of Ellipses (5)

(c) Demonstrate how an external tangent is drawn to two unequal circles. (10)

(d) Show how an internal tangent is drawn to two equal circles (5)

Examiner Mavumbu T (Mr) Moderator Sithole A (Mrs)


(e) Illustrate how an external tangent is drawn to equal circles (5)

3. Draw a diagram showing the application of the following drawing lines, (6)

(a) Outlines (d) Leader line

(b) Centre lines (e) Extension lines

(c) Dimension lines (f) Hidden detail lines

4. (A) Construct a triangle with base angles 45° and 30° with a base length of 60mm. (9)

(b) Construct an inscribed circle to this triangle and state its diameter. (5)

5. With the aid of clear diagrams, explain the following dimensioning terms. (20)

(a) Functional dimensions


(b) Auxiliary dimensions
(c) Chain dimensions
(d) Datum dimensions
(e) No functional dimensions

Due Date 27 May 2022

Assignment Three

1. a) Name two instruments used in freehand sketching. (2)


b) Draw (ii) a well labelled flat file using freehand sketching. (8)
(iii) a Ball pein hammer using freehand sketching (10)
2. With the use of clearly visible diagrams, explain the following projections
a) Isometric
b) oblique
c) Orthographic (30)
3. Explain the difference among Isometric , oblique and Orthographic projections (10)
4. With the aid of clear diagrams explain the difference between diagrams in 1st and 3rd
angle orthographic projections adding the appropriate symbols. (20)
5. Draw isometric circles of diameter 50mm and 60mm respectively using
a) Ordinate method (10)
b) Compass method(10)

Due Date 17 June 2022

Examiner Mavumbu T (Mr) Moderator Sithole A (Mrs)


Assignment Four

1. (a) At what angles are Isometric diagrams drawn? (2)

(b) Draw a square of side 50mm in Isometric projection (8)

2. (a) Draw the following ellipses given major and minor axis as 80mm and 30 mm respectively
using:

(i) Auxiliary circle method (10)

(ii) Radial method (10)

3. Show the meaning of the following terms using a well-constructed Hexagon. On different
diagrams.

(i) A/F (10) (ii) A/C (10)

4. Draw the diagram below full size in Isometric projection.50 Marks

Examiner Mavumbu T (Mr) Moderator Sithole A (Mrs)


I

Due Date 15 July 2022

Examiner Mavumbu T (Mr) Moderator Sithole A (Mrs)

You might also like