CODES - THE BASICS OPERATING INSTRUCTIONS

• The
 KitLock has four code levels FUNCTIONS The KitLock 1200 has a 10 button Blue LED = Code accepted LOST CODE PROCEDURE PENALTY TIME BATTERY FAILURE OVERRIDE THE PROCEDURE IS AS FOLLOWS: Every program command must commence •W
 hen in B) Public Use Function
available: Before programming select the most keypad and a # bar. Note: The procedure requires the door to • Entering three incorrect codes will The KitLock has been designed so an • Place the contact points of the PP3 by pressing the # bar when in A) Private the # bar is not required for
i) Master Code appropriate function for the application. The # bar is only used for programming Red LED = Code rejected be open. cause the lock to shutdown for 10 external PP3 battery can be placed against battery against the contact points Use Function (factory default), followed by programming. Ensure lock is
ii) Sub-Master Code functions when lock is in A) Private Use seconds. the external contacts beneath the handle at the base of the lock, making firm either the Master Code, Sub-Master Code free of User Code.
iii) User Code A) PRIVATE USE Function. • Remove the rear fixing bolts and so that the lock can be opened to replace maintained contact. or User Code.
iv) Technician Code Important Note: This is the default remove the lock from the door. BATTERY POWER batteries should they fail. • If necessary the # bar may be
• The KitLock is supplied with two function and is already CODES The lock has the following code levels: • The KitLock should provide well • The positive + PP3 terminal against the used to clear a previous entry if
factory set codes: pre-programmed in new locks. • Remove one battery. in excess of 50,000 openings, of 4 + contact on the lock, and the negative a mistake is made.
Master Code: 11 33 55 77 A) MASTER CODE C) USER CODE seconds each, from 2 x AAA 1.5v cells. – PP3 terminal against the negative
User Code: 22 44 This is the most common function The Master Code can: The User Code can: • Press and hold the 1 button, replace contact on the lock. See image. • T o enter a valid code, 10
• When fitted immediately change and is used where the same code • Open the lock • Open the lock the battery, the Blue LED will flash LOW BATTERY seconds are allowed between
the Master Code and User Code. will be repeatedly used. • Change the Master Code • Change the User Code twice, release the 1 button. Within • When the battery power is low the • Enter the Master Code. each button input; otherwise the
• All Master Codes and Sub-Master • Set the Sub-Master and User Code three seconds press the 1 button • Red LED will flash three times program will once again clear.
Codes are 8 digits long. • Change the Sub-Master and User Code
• Delete the Sub-Master and User Code
D) TECHNICIAN CODE
The Technician Code can:
three times. before the • Blue LED lights accepting • The lock will now withdraw the locking
• All User Codes are 4 digits long. B) PUBLIC USE the code. Fit new batteries as soon as pin allowing the lock to open.
• All Technician Codes are The user enters their own personal • Select between Private and Public • Open the lock in Technician mode The Blue LED will flash twice and the this happens. The lock will operate for
6 digits long. four-digit code. This locks the lock. Functions without erasing User Code when in lock will have reverted to the factory 100 times with low battery. • Fit new batteries by removing the lock
• The lock ‘open’ time is set The same code is entered to open the • Set or delete Technician Code B) Public Use Function. Master Code 11 33 55 77 and all other from the door. Refit the lock.
at 4 seconds. lock before being erased and ready • Disable or enable the sounder stored settings will be erased. • low
Code rejected
for the next new user. The same code cannot be programmed battery indication

This function is used for short term,

into more than one level.
• Code accepted
multi occupancy applications,
B) SUB-MASTER CODE
e.g. a locker in a leisure centre.
The Sub-Master Code can:
• Open the lock
• Change the Sub-Master
• Set / Change / Delete / the User Code
 KL12OO
POI-KL1200- v2:0813
CHANGE THE MASTER CODE CHANGE THE SUB-MASTER CODE CHANGING FROM A) PRIVATE USE TO B) PUBLIC USE WITH CHANGING FROM B) PUBLIC USE TO A) PRIVATE USE

MASTER CODE COMMANDS

SUB-MASTER CODE COMMANDS

SPECIAL MASTER CODE COMMANDS

Vertical
#Master Code • • 01 New Master Code • New Master Code •• • • •
#Sub-Master Code 06 New Sub-Master Code New Sub-Master Code •• TECHNICIAN CODE ENABLED • ••
Master Code 11
• •
Example: #11335577 01 12345678 • ••
12345678 Example: #22446688 • • 06 11335500 • 11335500 •• #Master Code • • 12 Technician Code • Technician Code•• • ••
Example: 11335577 11
Result: Master Code has been changed to 12345678. Result: Sub-Master Code has been changed to 11335500. • •
Example: #11335577 12 555555 • 555555 •• Result: Lock will revert to A) Private Use with the default User Code 2244 active until
Note: # prefix not required when in B) Public Use. Note: # prefix not required when in B) Public Use. Result: The lock is automatically set into function B) Public Use AND allows reprogrammed.
the programmed Technician Code to open the lock WITHOUT the entered User Note: When the program is changed from B) Public Use above to A) Private Use.
SET OR CHANGE THE USER CODE SET OR CHANGE THE USER CODE Code being erased. Use A) Private Use Function, the locking pin should now move to the locked position
#Master Code • •02 •• User Code #Sub-Master Code • •
07 User Code •• Note: If lock is opened with a Master Code the User Code will be erased. and previous single User Code erased. The # bar will now be required for programming.
• • ••
Example: #11335577 02 1455 Example: #11335500 • • 07 9999 ••
Result: New User Code 1455 now operative. Result: New User Code 9999 now operative. CHANGING FROM A) PRIVATE USE TO B) PUBLIC USE WITHOUT SET THE LOCK IN TECHNICIAN MODE
A TECHNICIAN CODE • • •
Master Code 12 Technician Code Technician Code ••
CODELOCKS LTD UK DELETE USER CODE DELETE USER CODE #Master Code • ••09 • •
Example: 11335577 12 555555 • 555555 ••
Tel: +44 (0) 1635 239645 #Master Code • ••
03 #Sub-Master Code • ••
08 • ••
Example: #11335577 09 Result: The lock set into Technician mode with Technician Code 555555
Fax: +44 (0) 1635 239644
[email protected]
• ••
Example: #11335577 03 Example:#11335500 • •• 08 Result: The lock will now work in B) Public Use. Note:
Result: User Code deleted. Result: User Code deleted. Note: 1. Technician Code only available when lock is set in B) Public Use.
1. The locking pin is now programmed to be withdrawn when using the above 2. The Technician Code is able to open the lock without the entered User Code
Helpline, service & spares
FREEPHONE 0800 393 405
SET OR CHANGE THE SUB-MASTER CODE code string and is waiting and ready to accept a User Code. Please note that the being erased.
#Master Code • • 04 Sub-Master Code • Sub-Master Code •• A) PRIVATE USE: CHANGING THE USER CODE keypad is now inactive when the lever is in the open position. 3. Opening the lock with the Master Code will erase the User Code.

USER CODE COMMANDS

CODELOCKS INC US • •
Example: #11335577 04 22446688 • ••
22446688 #User Code • New User Code •
New User Code •• 2. Only the Master Code and Sub-Master Code will be retained from A) Private
Tel: +1 714 979 2900 Result: Sub-Master Code 22446688 now operative. Example: #2244 • 5541 •5541 •• Use Function. DELETE THE TECHNICIAN CODE
Fax: +1 714 979 2902
[email protected]
Note: # prefix not required when in B) Public Use. Result: User Code now 5541. Master Code • • ••
13 13 Programming
RESTRICT THE LOCKED TIME Result: Technician Code deleted. & Operating
KitLock is a
DELETE THE SUB-MASTER CODE B) PUBLIC USE: SET THE USER CODE Master Code • • 10 (number of hours lock to remain locked) •• Instructions
Codelocks Ltd brand #Master Code • • ••
05 05 •
Enter personal four-digit code to lock Re-enter same code to open •• • • ••
Example: 11335577 10 04 DISABLE/ENABLE SOUNDER
www.codelocks.com • • ••
Example: #11335577 05 05 Note: Result: The lock will auto open after 4 hours. If a new User Code is entered it The default is for the sounder to activate at every button press.
Result: Sub-Master Code deleted. 1. When the lock is opened the User Code will be erased and ready for will once again relock for 4 hours. To disable the sounder enter the following toggle code string:
Note: # prefix not required when in B) Public Use. the next new user to enter their code. If the lock is opened during the 4 hour period then the lock remains open until Master Code • • ••14 14
2. When locked in B) Public Use Function the • LED will flash every two seconds a new User Code is entered as normal. Result: No sound when buttons pressed. To enable the sounder repeat above
indicating locked status. Note: This program will only work when the lock has been set into B) Public code sequence.
3. Keypad in this function is only active when lever is in closed position. Use Function. The two digits number of hours lock to remain locked is 02, 04,
06, 08, 10 or 12.
www.kitlock.com