LG 47lw5600 - Training Manual

1080P Direct View LCD Training
47LW56000
LED Backlights
LCD-DV Troubleshooting 47" Class 1080P 120Hz LED TV SmartTV (46.9" diagonally)
Published June 1st, 201 1
OUTLINE
Preliminary Section: y Contact Information, Preliminary Matters, LCD Overview, General Troubleshooting Steps Product Information Section: Specifications Menu Information Specifications, Cinema 3D Section: Screen design and theory Disassembly Section: Removal of Circuit Boards Troubleshooting Section: Board Operation Troubleshooting of : Switch Mode Power Supply with LED Backlight Driver Main Board T CON (TFT Panel Driver Board) T-CON Front IR/Intelligent/Soft Touch Key Board Speaker
2 June 201 LCD TV 1 47LW56000
Overview of Topics to be Discussed
47LW56000 LCD Direct View Display

Section 1
This Section will cover Contact Information and remind the Technician of Important Safety Precautions for the Customers Safety as well as the Technician and the Equipment. Basic Troubleshooting Techniques which can save time and money sometimes can be overlooked. These techniques will also be presented. This Section ill t th T h i i f ili Thi S ti will get the Technician familiar with the Disassembly, Identification and ith th Di bl Id tifi ti d Layout of the LCD Display Panel.
At the end of this Section the Technician should be able to Identify the Circuit Boards f S f C and have the ability and knowledge necessary to safely remove and replace any Circuit Board or Assembly.
June 201 LCD TV 1
47LW56000
Preliminary Matters (The Fine Print)
IMPORTANT SAFETY NOTICE

The information in this training manual is intended for use by persons possessing an adequate background in electrical equipment, electronic devices, and mechanical systems. In any attempt to repair a major Product, personal injury and property damage can result. The manufacturer or seller maintains no liability for the interpretation of this information, nor can it assume any liability in conjunction with its use. When servicing this product, under no circumstances should the original design be modified or altered without permission from LG Electronics. Unauthorized modifications will not only void the warranty, but June lead to property damage or user injury If wires screws, clips, straps, nuts, or washers used to complete a ground path are removed for injury. wires, screws clips straps nuts service, they must be returned to their original positions and properly fastened.
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for g purposes, disconnect the p , power immediately after p y performing the necessary checks. Also be g y diagnosis or test p p aware that many household products present a weight hazard. At least two people should be involved in the installation or servicing of such devices. Failure to consider the weight of an product could result in physical injury.
June 201 LCD TV 1
47LW56000
ESD Notice
(Electrostatic Static Discharge)
Todays sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage the electronics in a manner that renders them inoperative or reduces the time until their next failure. Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively, you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before removing a replacement part from its package, touch the anti static bag to a ground connection point or anti-static unpainted metal in the product. Handle the electronic control assembly by its edges only. When repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory Information l f
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to g provide reasonable p protection against harmful g Part 15 of the FCC Rules. These limits are designed to p interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction manual, June cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is reception, on, encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the dealer or an experienced radio/TV technician for help.
June 201 LCD TV 1
47LW56000
LG Contact Information
Customer Service (and Part Sales) (800) 243-0000 Technical Support (and Part Sales) (800) 847-7597 USA Website (GSFS) Customer Service Website Knowledgebase Website LG Web Training LG CS Learning Academy http://gsfs-america.lge.com http://www.us.lgservice.com http://lgtechassist.com https://lge.webex.com http://ln.lge.com/ilearn
New: 2010/11 Wireless Ready Models Software Downloads Presentations with Audio/Video and Screen Notations
http://136.166.4.200
Training Manuals, Schematics with Navigational Bookmarks, Start-Up Sequence, Owners Guides, Interconnect Diagrams, Dimensions, Connector IDs, Product Pictures and Features. I t t Di Di i C t ID P d t Pi t dF t Also available on the Plasma Page: PDP Panel Alignment Handbook, Plasma Control Board ROM Update (Jig required)
Published June 2011 by LG Technical Support and Training LG Electronics Alabama, Inc. 201 James Record Road, Huntsville, AL, 35813.
June 201 LCD TV 1
47LW56000
LCD Direct View Overview

Safety and Handling Regulations
1. Approximately 20 minute pre-run time is required before making any picture performance adjustments from the Menu. 2. Refer to the Voltage/Current silk screening on the Switch Mode Power Supply. 3. C-MOS circuits are sensitive to static electricity. C MOS Use caution when dealing with these IC and circuits. 4. Exercise care when making voltage and waveform checks to prevent costly short circuits from damaging the unit. 5 5. Be cau ous o lost sc e s a d o e metal objec s to p e e a poss b e s o in the e cautious of os screws and other e a objects o prevent possible short e circuitry.
Checking Points to be Considered

1. Check the appearance of the Replacement Panel and Circuit Boards for both physical damage and part number accuracy. 2. 2 Check the model label Verify model names and board model matches label. matches. 3. Check details of defective condition and history. Example: Oscillator failure dead set, etc
June 201 LCD TV 1
47LW56000
Basic Troubleshooting Steps

Define, Localize, Isolate and Correct Define Look at the symptom carefully and determine what circuits could be causing the failure. Use your senses Sight, Smell, Touch and Hearing. Look for burned parts and check for possible overheated components. Capacitors will sometimes leak dielectric material and give off a distinct odor Frequency of power supplies will change with the load or listen for odor. load, relay closing etc. Observation of the front Power LED June give some clues. Localize After carefully checking the symptom and determining the circuits to be checked and after giving a thorough examination using your senses the first check should always be the DC Supply Voltages to those circuits under test. Always confirm the supplies are not only the proper level but be sure they are noise free. If the supplies are missing check the resistance for possible short circuits. Isolate To further isolate the failure, check for the proper waveforms with the Oscilloscope to make a final determination of the failure. Look for correct Amplitude Phasing and Timing of the signals also check for the proper Duty Cycle of the signals. Sometimes glitches or road bumps will be an indication of an imminent failure glitches road bumps failure. Correct The final step is to correct the problem. Be careful of ESD and make sure to check the DC Supplies for proper levels. Make all necessary adjustments and lastly always perform a Safety AC Leakage Test before returning the product back to the Customer. Customer
June 201 LCD TV 1
47LW56000
47LW56000 PRODUCT INFORMATION SECTION
This section of the manual will discuss the specifications of the 47LW56000 LCD Direct View Display
9 June 201 LCD TV 1 47LW56000
Wireless Media Box

Wireless Media Box (Sold Separately)
The Wireless Media box communicates to the television via a wireless receiver called a Dongle. The Dongle attaches to the Television via two connections: 1. HDMI Cable from the Dongle to the TV to transfer Audio and Video Signals. 2. Wired Remote cable between the TV and Dongle for Control Functions.
Media Box
Wired Remote to control the Media Box TV A/V Inputs
Wireless Receiver/Transmitter Wi l R i /T itt Dongle Attaches via Velcro to the back of the set HDMI
10
June 201 LCD TV 1
47LW56000
Wireless Network Adaptor (AN-WF100)

Wireless Network Adaptor Sold Separately
Using the LG Wireless LAN for Broadband Adaptor, which is sold separately, allows the TV to connect to a wireless LAN network. The Wireless Network adaptor attaches to the Television via either of the two USB connections: Allows access to DLNA: Digital Living Network Alliance
AP (Wireless Router)
Side A/V Inputs
Wireless Adaptor Dongle
Cat 5 Cable with RJ 45 Connectors on each side
Modem
1 1
June 201 LCD TV 1
47LW56000
Basic Specifications
LG Smart TV1 LG Cinema 3D2 2D to 3D Conversion
Key TV Features
1
LED Plus w/Local Dimming TruMotion 120Hz Wi-Fi Ready (Adapter Included) Magic Motion Remote (Included) Full HD 1080p Resolution DLNA Certified ENERGY STAR Qualified Picture Wizard II Intelligent Sensor Smart Energy Saving ISF ISFccc Ready R d
12
Internet connection & subscriptions required and sold separately. The Magic Motion Remote does not come equipped with all LG Smart TV enabled TVs and a separate purchase maybe required. The Hulu Plus service is projected to be available via a firmware update in June 2011. The LG web browser does not support Flash 10 or HTML 5, therefore, access to certain web content June be limited or unavailable.
For a small percentage of the population, the viewing of stereoscopic 3D video technology may cause discomfort such as headaches, dizziness or nausea. If you experience any symptoms, discontinue using the 3D functionality and contact your health care provider. 4 Pairs of 3D glasses are included.
June 201 LCD TV 1
47LW56000
Logo Familiarization Page 1 of 3

LG Cinema 3D
Want 3D like you get it in the movie theater? Lightweight glasses, wider viewing angles and with clear 3D images? LG's Cinema 3D experience can bring it right to your home. Enjoy amazing depth along with smoother, crisper images, and a clear picture from virtually any angle.
LED Plus
Want deeper blacks and richer colors? LGs LED Plus technology provides even greater control of brightness through local dimming technology to deliver better contrast, amazing clarity and color detail, as well as greater energy efficiency compared to conventional LCD TVs.
LG SmartTV
A revolutionary, easy way to access virtually limitless content, thousands of movies, customizable apps, videos and browse the web all organized in a simple to use interface interface.
Magic Motion Remote (Included) Just point and choose selections with LG's unique motion-controlled Magic Remote. Remote
13
June 201 LCD TV 1
47LW56000

DLNA Certified g ,y g To build a digital network, you need digital devices. Thats obvious. But unless those devices are compatible, it wont be much of a network. DLNA Certified devices work together. FULL HD RESOLUTION 1080P HD Resolution Pixels: 1920 (H) 1080 (V) This stunning picture is the reason you wanted HDTV in the first place. With almost double the pixel resolution, Full HD 1080p gives it superior picture quality over standard HDTV. Youll see details and colors like never before. WiFi Ready: Getting your LG TV connected to NetCast Entertainment Access and other online content is easy when you are WiFi Ready. If you have existing wireless broadband, setting it up is simple and you don't need to worry about messy wires. Intelligent Sensor The Intelligent sensor will monitor the room lighting environment. When the room lights go out, the TV will automatically adjust the picture for the best viewing enjoyment. Picture Wizard Get easy self-calibration with on-screen reference points for key picture quality elements such as black level, color, tint, sharpness and backlight levels. Take the guesswork out of picture adjustments with this simple-to-use feature. It's not actually magic, but it will sure seem that way.
14
June 201 LCD TV 1
47LW56000

Clear Voice Clearer dialogue sound g Automatically enhances and amplifies the sound of the human voice frequency range to provide high-quality dialogue when background noise swells. Save Energy Save Money Energy, Home electronic products use energy when they're off to power features like clock displays and remote controls. Those that have earned the ENERGY STAR use as much as 60% less energy to perform these functions, while providing the gy same performance at the same price as less-efficient models. Less energy means you pay less on your energy bill. Draws less than 1 Watt in stand by. TruMotion 120Hz See sports, video games and high-speed action with virtually no motion blur and in crystal clarity with LGs TruMotion 120Hz technology Now your TV LG s technology. can keep up with the fastest moving scenes. 5M:1 Dynamic Contrast Ratio Worrying about dark scenes is a thing of the past. The mega contrast ratio of 5,000,000:1 delivers vivid colors and deep blacks. AV Mode "One click" Cinema, THX Cinema, Sport, Game mode. TAKE IT TO THE EDGE is a true multimedia TV with an AV Mode which allows you to choose from 4 different modes of Cinema Sports Cinema, and Game by a single click of a remote control.
15
June 201 LCD TV 1
47LW56000
47LW56000 Remote Control

TOP PORTION
p/n AKB73295502 BOTTOM PORTION
16
June 201 LCD TV 1
47LW56000
TV Rear Input / Output Jacks

Rear In/Out Jacks
USB1 or USB2 for Software Upgrades, Music, Videos and Photos. Also for the Wireless Network adaptor. p
Side In/Out Sid I /O t

USB 2 USB 1
Wireless Media Box Remote Jack AV/Component In AV/Component In Antenna In HDMI 4 HDMI 3 RS232 In HDMI 2 HDMI 1
LAN
RGB
RGB Audio
Optical Out
Head Phones
17
June 201 LCD TV 1
47LW56000
Software Updates (New and Changed Functions)

A wireless Internet Connection will work for Automatic Software Downloads, however if there are problems completing download, a Wired Internet Connection is preferred Bring up the Customers Menu then cursor down 2 times, (Input) will be highlighted. Cursor right to highlight ( (SETUP). ) Press ENTER on the Remote. Scroll down to highlight the ? mark ( (SUPPORT). ) Cursor right to highlight Software Update, Press ENTER on Remote
Highlight Check Update Version g g p to see if an update is available. Scroll up to highlight ON and cursor right to turn off automatic Software Update. p
18
June 201 LCD TV 1
47LW56000
Generic Plasma USB Automatic Software Download Instructions

1) Download the Software File.
Jump Drive Directory
Software File LG_DTV Sub-Directory
2) Copy new software (xxx epk) to "LG DTV" (xxx.epk) LG_DTV folder. Make sure to have correct software file. 3) With TV turned on, insert USB flash drive. 4) The TV Software Upgrade screen appears. (See figure to right) 5) Cursor left and highlight "START" Button and push Enter button using the remote control. 6) You can see the download progress Bar. 7) D not unplug until unit h automatically Do t l til it has t ti ll restarted. 8) When download is completed, you will see COMPLETE. 9) Your TV will be restarted automatically.
Currently Installed Version Software Version found on the USB Flash Drive File found on the USB Flash D i Fl h Drive
* CAUTION: Do not remove AC power or the th USB Flash Drive. Do not Fl h D i D t turn off Power, during the upgrade process. Highlight Start Press Select
Software Files are now available from LGTechassist.com
19
June 201 LCD TV 1
47LW56000
Manual Software Download:

Prepare the Jump Drive as described in the USB Automatic Download section and insert it into either of the USB ports. Bring up the Customers Menu then cursor down 2 times, (Input) will be highlighted. Cursor right to highlight (SETUP). Press ENTER on the Remote. ENTER Remote Scroll to OPTIONS, (Nothing should be highlighted on the right side). Press the FAV key 7 times to bring up the first screen for Manual Download Screen (Expert Mode).
Press the FAV key 7 times
Location of files found On the Jump Drive
File shown is not correct for this model. Scroll down and highlight Options Options WARNING: Use extreme Caution when using the Manual Forced Download Menu. Any file can be downloaded when selected and June cause the Main board to become inoperative if the incorrect file was selected. Highlight the Software update file which will appear at the bottom of the screen. (Scroll down if more than one file is on the jump drive). Press SELECT to begin the download process.
20
June 201 LCD TV 1
47LW56000
Product and Service Info. Menu

1) Bring up the Customers Menu then cursor down 2 times, (Input) will be highlighted. Cursor right to highlight (SETUP). Press ENTER on the Remote. 2) Scroll down to highlight the ? mark (SUPPORT). Cursor right and scroll down to highlight Product/Service Info, Press ENTER on Remote
3) Information for Customer Support appears. Note: Model Number does not include suffix.
21
June 201 LCD TV 1
47LW56000
Accessing the Host Diagnostic Screen (Page 1 of 2)

Use the Host Diagnostic screen to investigate the signal quality of a problem channel. 1) Place Television on the digital channel that ) g June be showing problems. 2) Bring up the Customers Menu. Cursor down two times and right once to highlight Setup. Press Enter on the remote. 4) Scroll down and highlight Options.
5) Press the (1) Key 5 times. The Host Diagnostics screen appears. 3) The Setup Menu appears.
See next page for more details.
22
June 201 LCD TV 1
47LW56000
42LW5600 Understanding the Host Diagnostic Screen (Page 2 of 2)

Host Diagnostics
Host Information Model Name : 42LV5500-UA (Liquid Crystal Display) Memory FLASH : 524288 KB DRAM : 524288 KB NVM : 128 KB Host Release Version Firmware Version(MP) : 3.01.15.01(31010)
Software Version Channel Selected
Current Channel (Main)
Channel Info : Digital 19-1
Blocked or Not Blocked
Parental Control : Channel is not blocked DVI/HDMI Status Cant display this information now Wireless ready Status
Wireless Host Ver:0.00.0 Wireless B/B Ver:0.00.0 Micom Version : V3.21.6 RF Region Config : Not Configured Compile Date & Time : 20110127 & 08:45:52 Media Box Type : Not Configured RF Frequency (Value):Auto (N.A.) Compile User : tu.ryu Uplink RF Power gain (Value):Auto (Min 0) FAT Status (Main) Downlink RF Power gain (Value):Auto:Auto (Min 0) Channel Frequency Center Frequency : 663.00 MHz Link Mode : Unicast Program Clock Reference (Locked or No) RX MAC Address : ff:ff:ff:ff:ff:ff PCR lock : Locked TX MAC Address : ff:ff:ff:ff:ff:ff Channel Type (8VSB, QAM 64, 256) Modulation mode : QAM 256 Wireless connection status : Disconnected Channel (Locked or Unlocked) Carrier lock status : Locked Average SNR [Db] : 0.0 (0) is good) 8VSB (Above 20 Channel Signal to Noise Ratio SNR : 37 dB QAM 64 (Above 24 is good) Signal level : 100%
Channel Signal Level (Above 80% good) QAM 256 (Above 30 is good)
Half Page
CH
Move Page
Exit
23
June 2011
LCD-DV 47LW5600
Accessing the Service Menu
To access the Service Menu. 1) You must have either Service Remote. ) p/n 105-201M or p/n MKJ39170828 2) Press In-Start 3) A Password screen appears. 4) Enter the Password. )
Note: A Password is required to enter the Service Menu. Enter; 0000 ; Note: If 0000 does not work use 0413.
105-201M
MKJ39170828
24
June 201 LCD TV 1
47LW56000
47LW5600 Service Menu First Page

Bring up the Service Menu using the Service Remote And pressing In-Start enter password 0413.
IN START
Model and S/N
1. Adjust Check Model Name: 47LW5600-UA 2. ADC Data Serial Number: 101RMCJ6B723 SW Version : 03.11.04.01 3. Power Off Status S/W Version: : 3.21.6 4. System 1 MICOM Version : 1.02.51 5. System 2 BOOT Version Video Processor : 21.00 6. Model Number D/L FRC Version Chip Type : a2.0 7. Test Option IR LED Version : 0.03/0.02 8. External ADC EDID (RGB/HDMI) : BCM 35230 9. Spread Spectrum Chip Type : 0.00.0 10. Sync Level Wireless Host Ver. : 0.00.0 11. Wireless Ready Wireless B/B/ Ver. : 1.0 12. Stable Count Vi-Fi Version :0 13. ODC Test Vi-Fi Channel 14. Local Dimming Wi-Fi MAC : 00:00:00:00:00:00 15. SDP Server Selection MAC Address : E8:5B:5B:30:31:7F 16. Network Error History Widevine : LGTV10L000024476 ESN Num. : LGE-LV5600XXXX0010AC93E8 : 21.00 Formatter Version Electronic RF Receiver Version : VB091 Serial No. : RELEASE Debug Status UTT : 12 APP History Ver.:47769E PQL DB:LGD_ELF_SANYO_XXXXXX
Units Total Time
Adjust Check Country Group 1. Country Group (Press OK to Save) Country Group Code 02 Country Group US Country US 2. Tool Option Tool Option 1 33176 Tool Option 2 4161 Tool Option 3 7295 Tool Option 4 21897 Tool Option 5 14925 Tool Option 6 667 3. Adjust White Balance: OK(12) 4. Adjust ADC: OK(Manual) 480i Component OK 1080p Component OK RGB OK 5. EDID(PCM): OK RGB OK (0x98) HDMI1 OK (0x7f,0x6F) Priority Audio HDMI2 OK (0x7f,0x5F) Processing Mode HDMI3 OK (0x7f,0x4F) HDMI4 OK (0x7f,0x3F)
25
June 2011
LCD-DV 47LW5600
47LW5600 Model Number Download Screen

When the Main Board is replaced, the Model Number and Serial Number must be corrected. Follow these instructions
IN SART Model Name: 47LW5600-UA Serial Number: 101RMCJ6B723 : 03.11.04.01 S/W Version: : 3.21.6 MICOM Version : 1.02.51 BOOT Version Select Item 6 : 21.00 FRC Version : a2.0 IR LED Version : 0.03/0.02 EDID (RGB/HDMI) : BCM 35230 Chip Type : 0.00.0 Wireless Host Ver. : 0.00.0 Wireless B/B/ Ver. : 1.0 Vi-Fi Version :0 Vi-Fi Channel Wi-Fi MAC : 00:00:00:00:00:00 MAC Address : E8:5B:5B:30:31:7F Widevine : LGTV10L000024476 ESN Num. : LGE-LV5600XXXX0010AC93E8 : 21.00 Formatter Version RF Receiver Version : VB091 : RELEASE Debug Status UTT : 12 APP History Ver.:47769E PQL DB:LGD_ELF_SANYO_XXXXXX 1. Adjust Check 2. ADC Data 3. Power Off Status 4. System 1 5. System 2 6. Model Number D/L 7. Test Option 8. External ADC 9. Spread Spectrum 10. Sync Level 11. Wireless Ready 12. Stable Count 13. ODC Test 14. Local Dimming 15. SDP Server Selection 16. Network Error History
Bring up the Service Menu using the Service Remote. Scroll down to item 6. Model Number D/L to highlight. Press ENTER or Cursor Right.
Model Number D/L 0. Model Name 1. Serial Num. 47LW5600-UA 101RMCJ6B723 Press OK to Save
To Change the Model Number 1) Use the cursor right or left to select the area to change. 2) Use the cursor up or down to change. 3) Cursor right until there is no text cursor blinking. 4) Cursor down to highlight Serial Number and change. 5) Press ENTER to Save
26
June 2011
LCD-DV 47LW5600
47LW5600 UTT Reset (IN START) Screen

IN START Model Name: 47LW5600-UA Serial Number: 101RMCJ6B723 : 03.11.04.01 S/W Version: : 3.21.6 MICOM Version : 1.02.51 BOOT Version : 21.00 FRC Version : a2.0 IR LED Version : 0.03/0.02 EDID (RGB/HDMI) : BCM 35230 Chip Type : 0.00.0 Wireless Host Ver. : 0.00.0 Wireless B/B/ Ver. : 1.0 Vi-Fi Version :0 Vi-Fi Channel Wi-Fi MAC : 00:00:00:00:00:00 MAC Address : E8:5B:5B:30:31:7F Widevine : LGTV10L000024476 ESN Num. : LGE-LV5600XXXX0010AC93E8 : 21.00 Formatter Version RF Receiver Version : VB091 : RELEASE Debug Status
Units Total Time
SYSTEM 1 1. Adjust Check 2. ADC Data 3. Power Off Status 4. System 1 5. System 2 6. Model Number D/L 7. Test Option 8. External ADC 9. Spread Spectrum 10. Sync Level 11. Wireless Ready 12. Stable Count 13. ODC Test 14. Local Dimming 15. SDP Server Selection 16. Network Error History 0. Baudrate 1. 2 Hours Off (On Timer) 2. 2 Hours Off (Screen Mute) 3. 15Min Force Off 4. Audio EQ 5. Dynamic EQ 6. A2 Threshold 7. HDMI Sound(Port1) 8. Lip Sync Adjust(DTV) 9. Dimming 10. Tuner Option 11. Atten RF Signal 12. UTT Reset 13. Channel Mute 14. Debug Status Changes 15. NVRAM Type to Doing 16. HDEV 17. Blue back 18. China Cable SO 19. Booster On (VHF) 20. Booster Off (VHF) 21. Booster On (UHF) 22. Booster Off (UHF) 23. Auto ADC
Scroll to (UTT Reset) Press (Select) Reset changes to Doing then back to Reset
UTT : 12 APP History Ver.:47769E PQL DB:LGD_ELF_SANYO_XXXXXX

Note: After UTT is reset, the UTT time on the left will not reset to 0 until the Service Menu is exited. Scroll to (System 1) then Right Cursor
38400 On Off On On On 11 HDMI Port1 0 On Enhanced Ghost Off Reset On RELEASE EEPROM Off On On 0 0 0 0 Off
After Reset (Doing) has completed, Reset returns. After Exit the UTT Timer is 0
27
June 2011
LCD-DV 47LW5600
Service Menu: Downloading EDID Data

1) Press ADJ key. When Item 11 was selected
If Item 5 on Adjust Check in the 1st page of the Service Menu shows AC3, this shows NG. If Item 5 on Adjust Check in the 1st page of the Service Menu shows EDID PCM this shows OK(PCM) If NG was shown, highlight Start and press Select on the , g g p remote. Writing appears, then OK/(PCM) shows here. Now Item 5 on Adjust Check in the 1st page of the Service Menu shows EDID PCM. If Reset i selected, E i will appear and then this shows R t is l t d Erasing ill d th thi h NG.
When Item 12 was selected Password required

If Item 5 on Adjust Check in the 1st page of the Service Menu shows PCM, this shows NG. If Item 5 on Adjust Check in the 1st page of the Service Menu shows EDID AC3 this shows OK(AC3) If NG was shown, hi hli ht St t and press S l t on th h highlight Start d Select the remote. Writing appears, then OK/(AC3) shows here. Now Item 5 on Adjust Check in the 1st page of the Service Menu shows EDID AC3 . If Reset is selected, Erasing will appear and then this shows NG.
Note: PCM is changed from NG to OK/(PCM) then AC3 will now be NG. Note: AC3 is changed from NG to OK/(AC3) then PCM will now be NG.
28
June 201 LCD TV 1
47LW56000
47LW5600 Product Dimensions

Wattage Typica 140W Max: 165W Stand By <0.1W There must be at least 4 inches of Clearance on all sides 43-7/8" 1115.06mm Center 1-3/16" 30.48mm
21-15/16" 557.3mm 5-3/16 131.5mm
14 355.5mm Model No. Serial No. Label
15-3/4" 400mm
26-7/8" 683.26mm 29-1/2" 749.3mm
Center
15-3/4" 400mm
13-7/16" 341.63mm
Remove 4 screws to remove stand for wall mount 2-5/8" (66.04mm) 20-11/16" 525mm 10-7/8" 276.86mm
Weight w/o Stand 40.8 lbs Weight with Stand 45.6 lbs
29
June 2011 47LW5600 LCD-DV
PASSIVE 3D SECTION
PASSIVE 3D This section of the manual will discuss the Passive 3D used in the 47LW56000 LCD Direct View Television. Upon completion of this section the Technician will have a better understanding of Passive 3D.
30
June 201 LCD TV 1
47LW56000
Advantages of Passive 3D
GLASSES AG-P110

ADVANTAGES Easy Wear

Comfortable Flicker Free Light No Batteries No Charging
Light Weight : 15g

Possible to watch 3D while laying down Horizontal (Left/Right) Viewing Angle Free Large group of people can watch simultaneously No synchronization pulse to interfere with.
4 Pair Come with the TV Additional Glasses Reasonably priced
Compatibility with all types of 3D Passive TV Maker Glasses can be made by p y polarized coating on normal g g glasses
31
June 201 LCD TV 1
47LW56000
PR Type of 3D Display
Pattern Retarder makes separation of polarization status. Each eye can see left and right images respectively when wearing polarized glasses glasses.
Right i Ri ht images input to odd lines i tt dd li Left images input to even lines
32
June 201 LCD TV 1
47LW56000
FPR 3D Display Design

Polarization film (PR) is placed on the front of the LCD panel 1st 2nd 3rd 4th Cell Polarizer Pattern Retarder
Right-handed Circularly polarization Left-handed Left handed Circularly polarization
Polarized glasses
Left Eye
Right Eye
1. Patterned Retarder plate is attached on the LCD module 2. Patterned Retarder plate rotates odd line to CW 45 degree and even line CCW 45 degree 3. Odd number pixels see through the Left lens and even number pixels see through the Right lens of the Polarized glasses 4. The brain combines separated images into 3D image
33
June 201 LCD TV 1
47LW56000
Polarizer State
Pattern retarder makes 2 kinds of polarization states; LHC, RHC Polarizer glasses is possible to distinguish polarization state. state
Polarization State #4 (Linear) Polarizer Polarization St t P l i ti State #3 (Circular) Quarter Wave Plate Polarization State #2 (Circular) Pattern Retarder Polarization State #1 (Linear) Polarizer of LCD
Distinguish polarization state - LHC : Left Handed Circularly Polarization - RHC : Right Handed Circularly Polarization
Divides light output into 2 kinds of polarization states - LHC : Left Handed Circularly Polarization - RHC : Right Handed Circularly Polarization
34
June 201 LCD TV 1
47LW56000
DISASSEMBLY SECTION
Disassembly: This section of the manual will discuss Disassembly, Layout (Circuit Board Identification) of the 47LW56000 LCD Direct View Television. Upon completion of this section the Technician will have a better understanding of the disassembly procedures, the layout of the printed circuit boards and be able to identify each board.
35
June 201 LCD TV 1
47LW56000
Panel Structure and Local Dimming

LED Array is on the side of Mod le Arra Module Backlight Structure g LED Array
Upper Metal M t l Cover
8 Blocks
8 Blocks Each f the E h of th 16 bl k can b controlled blocks be t ll d independently (Local Dimming) or all of them as a group (Global Dimming) P-DIM This allows the panel to be darkened out in areas that are black or low brightness areas of the video. This allows for more deeper blacks and a thin design design. 36 June 201 LCD TV 1 47LW56000
Removing the Back Cover
Remove the 29 screws indicated. Pay attention to the size and type of screw as there are many different types. Putting in an improper screw when reassembling June Cause damage. g g
The AC Cord unplugs under cover. Remove plastic cover.
The Stand has to be removed before removing the back.
37
June 201 LCD TV 1
47LW56000
Circuit Board Layout

To LEDs Warning: The Frame may have sharp edges
Power Supply (SMPS) Main Board
LVDS Cables
T-CON
Panel Connection Points
IR / Soft Touch Key Board
Invisible Speaker Right
Invisible Speaker Left
Motion Remote
38
June 201 LCD TV 1
47LW56000
47LW5600 Connector Identification Diagram

To LEDs
P203 P202
p/n: EBR72948402 AUSYLHR p/n: EBR73145901 AUSYLJR p/n: EBR72948404 AUSYLUR P3503
P101 n/c
POWER SUPPLY
p/n: EAY62169801 SK100 If the Panel is replaced, reset the UTTTime. Service Menu, System 1 Item 12
AC In
Black Plug
White Plug
P701 n/c
P502 P1702 P1502 P1501 P901 P1302
P832 P201
P601 n/c
TFT PANEL
Panel p/n: EAJ61768201 AUSYLHR, AUSYLJR, AUSYLUR Panel p/n: EAJ61928101 AUSYLUR
Comes with the Panel
MAIN BOARD
CN2
CN4
T-CON
To TFT Panel
CN1
CN5
IR Soft Touch Keys p/n: EBR72671301
Speaker (Front Right)
Speaker (Front Left)
p/n: EAB62088401
p/n: EAB62088401
Motion Remote Receiver
p/n: EBR72499601
39
June 2011
LCD -DV 47LW5600
Power Supply Board Removal
p/n EAY62169801
Disconnect P201, P202, P203, P832 and AC In SK100.
P701 n/c
P201
Remove the 6 screws indicated by the arrows arrows. Note: This screw Is a different size with washer. 40
SK100 AC In
Press in gently on the two tabs to release lock
SK100 fits very snug into its connector. Press in on the two tabs to release lock
June 201 LCD TV 1
47LW56000
Removing the Main Board

N/C
Disconnect P3503, P502, P1702, P1502, P1501, P901 and P1302.
P502
P3503 Screw removed d with Back
P1702 Press in on the side release tabs to remove.
Remove any tape holding down any cables. Remove the 5 screws indicated by the arrows arrows.
Remove the board.
Press in on the two releasing tabs, pull the LVDS ribbons out.
P1502
P1501 N/C
Decorative Metal Plate After removing the Main, there are tabs sticking through the Main board holding the Metal plate in place. Screw removed with Back
Remove the board. Then Remove the wrap around decorative Metal piece. p Note: It is one piece.
P901 P1302
p/n: EBR72948402 AUSYLHR p/n: EBR73145901 AUSYLJR p/n: EBR72948404 AUSYLUR / S
Screw removed with Back
41
June 201 LCD TV 1
47LW56000
Removing the T-CON (1 of 2)
Comes with the Panel T-CON is under a Shield. Remove the T-CON Shield (3 Screws).
T-CON is under the Stand Bracket. Remove the Stand Bracket (4 Screws).
Press in on the two side unlocking tabs.
Disconnect CN1, CN2, CN4 and CN5. Return Screws if testing board.
See next page for removing Connectors. CN2 CN1 Return Screws if testing b t ti board. d CN5 Flip up the unlocking tabs.
CN4
Flip up the p p unlocking tabs.
42
June 201 LCD TV 1
47LW56000
T-CON Board Removal Continued (2 of 2)

To remove the LVDS cables CN1 and CN2; Press i on th t P in the two tabs and slowly rock th cable out of th connector. t b d l l k the bl t f the t (Shown by the arrows in Figure above)
STEP (4)
Removing LVDS
Press In
Pull Out
From the Main (Top of the board) Pull Out Press In
Press In
(CN2) LVDS
(CN1) LVDS
Removing Ribbons
CN4
To the Panel (Bottom of the board)
CN5
Flip the locking tabs upward and pull out the ribbon cables.
43
June 201 LCD TV 1
47LW56000
Removing the Front IR Page 1 of 2

The Front IR Item 510 on the parts breakdown is under a wire routing bracket Item 511. Disconnect the cable coming from the Main board and remove it from the wire holders in Item 511.
IR/Key board p/n: EBR72671301 Remove the Speaker by sliding it forward.
Speaker Wire routing bracket, Slide Right
Tab
Tab
Screw
Tab
Remove the one screw. Lift up on the three tabs at the top of Item 511 and pull th It ll the Item 511 slightly forward. li htl f d Lift Item 511 up and out.
44
June 201 LCD TV 1
47LW56000
Removing the Front IR Continued

p/n: EBR72671301
Front IR/Key Board Exposed
After gaining access to the Front IR/Intelligent Sensor Board, lay the TV down on its face and remove the LCD Panel by releasing the tabs around the perimeter of the panel. Lift the Panel up and out. p p p The Front IR / Key Board is attached to the Front Frame Item 300 p/n: ABJ73289108. It must be separated to replace independently. Part number: EBR72671301
45
June 201 LCD TV 1
47LW56000
TROUBLESHOOTING SECTION
Troubleshooting: g This section of the manual will discuss troubleshooting. Upon completion of this section the Technician will have a better understanding of how to diagnosis and resolve problems.
46
June 201 LCD TV 1
47LW56000
POWER SUPPLY SECTION

This switch mode power supply develops Stand By 3.5V at all times when AC is applied. At power on, it develops 12V and 24V for the Main board. It develops 50V f th LED B kli ht d l for the Backlights. This power supply draws less than 1 watt during stand by mode. The fuse F101 and F501 reads approximately 398V (from hot ground) during this time. The transformer T501 delivers an AC signal which is rectified and filtered by D201, D202, C201 and C202 which develops a Stand-By voltage of 3.55V 3 55V which is used by the SMPS Controller circuit and is also sent to the Main Board It is output Board. P201 pins 9~12 and sent to the P502 on the Main Board. When the controller chip on the back side of the SMPS receives the PWR-ON command 3.41V via P201 Pin 1, it turns on the Relay RL101 which supplies AC to the bridge rectifier BD101. The primary section (Power Factor Controller circuit) increases its current supplying ability. Both Primary fuses F101 and F501 now read a little more than 396V. D253 receiving switching pulses from L601 develops the 50V for the LED backlights. When the SMPS receives the DRV ON command from the Main board via P201 Pin 18 (3 26V) it DRV_ON (3.26V) turns on the on-board Inverter to start driving the LED backlights. The backlight brightness is controlled by the Main board via PWM Pin 22 and Local Dimming signals via P832. P201 Connector: (To Main Board) 3.5V_ST (3.55V) t t 3 5V ST (3 55V) output P201 pins 9 12 i 9~12 12V (12V) output P201 pins 17, 19 and 21 24V (24V) output P201 pins 2, 3 and 4. Turn on commands. P202 Connector: (To Panel LEDs) 50V output P202 pins 1 and 12. P203 Connector: (To Panel LEDs) 50V output P203 pins 1 and 13. t t i d 13 P832 Connector: (To the Main Board) This connector receives the Local Dimming signals.
47
June 201 LCD TV 1
47LW56000
47LW5600 Power Supply Drawing

100uF/100V 100uF/100V
P203
50V
P202
P201 Connector "SMPS Board" To P502 "MAIN Board"
VC_3C
L601
- + - + C257 C256
Pin 24 23 22
Label ERROR n/c PWM 12V n/c 12V DRV-ON 12V V_Sync (n/c) Gnd 3.5V Gnd 24V PWR-ON
STBY n/c n/c 0V 0V n/c 0V 0V 0V n/c Gnd 3.55V Gnd 0V 0V
Run n/c n/c 0.2V~3.3V 11.92V n/c 11.92V 3.26V 11.92V n/c Gnd 3.53V Gnd 24.19V 3.4V
Test1 0V 0V 3.52V 12V n/c 12V 0V 12V n/c Gnd 3.55V Gnd 24.41V 3.55V
Diode 2.03V OL OL 0.48V OL 0.48V OL 0.48V OL Gnd 2.63V Gnd 1.09V 1.15V
VC_1D
VC_1C
VC_4D
VC_4C
VC_2B
VC_2A
VC_1B
VC_1A
VC_4B
VC_4A
VC_3D
BD101
D253
VC_2C
VC_3B
Cold (Chassis) Gnd side
Q251 + Q602
VC_3A
21 20 19 18
VC_2D
P701
n/c
Q601 IC102 D603
SMPS BOARD p/n: EAY62169801
D251 D252 D255 D256 Stand-By 3.5V Source C202 ,1 D202
17
P832
16 13-15 9-12 5-8
T101
RL101
Hot Ground Side
D261 D201
P201
2-4 1
F100
5A / 250V
W/Washer Different Size
T501
Q102
(1)
F501 F101
3.15A / 250V Stby: 399V Run: 398.5V Stby: 397V Run: 396.5V
IC501 Q101
IC502
1.6A / 250V
SK100 AC In
P-DIM1 (Digital Dimming) Global Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and room light condition. 0.2V 0% to 3.3V 100% and the Intelligent Sensor. Output from the Video Processor IC900.
47uF/450V
Indicates Hot Ground
47uF/450V
47uF/450V
50V Line: PWR-ON turns on the 50V supply but it will only be 36V. Note: A block of LEDs can not be turned on with this voltage. It will increase to 65V then drops to 50V in less that 20 seconds when the DRV-ON line goes high.
MODEL LGP4247-11SLPB INPUT 100-240V~50/60Hz 2.5A 3.5V = 1.8A 12V = 2.8A OUTPUT 24V = 1.2A 59.2V = 1.6A
SMPS TEST 1: To Force Power Supply On. Disconnect P502 on Main board. (A) Jump pins 9, 10, 11 or 12 (3.5V) to pin 1. Test Voltage Outputs 12V, 24V to Main and 36V to the Inverter Section of the SMPS. Remove AC power. Leave the jumper in place. No Backlights at this time. SMPS TEST 2: (B) Jump pins 9, 10, 11 or 12 (3.5V) to pin 18 (DRV-ON). Apply AC power, the Backlights should turn on. Note, the LED B+ will now jump to 65V then back down to 50V. Note; If there is a problem with a load from the panel backlights, you can remove AC and Disconnect P202 or P203. When AC is reapplied, the Backlight LEDs should turn on for about 4 seconds and then shut off.
48
June 2011
LCD-DV 47LW5600
47LW5600 Power Supply Start Up Sequence

AC In
(6) 50V is 36V w/PWR_ON (8) 50V w/DRV_ON 6 8
1
No AC Det in this model
Primary side fuses: F101 Stand-By 399V Run 398.5V (Hot Gnd) F501 Stand-By 397V Run 396.5V (Hot Gnd)
POWER SUPPLY (SMPS) P202

L601 D253
50V
Relays T510 & Rectifier

Stand By 3.5V Reg
Bridge
Inverter On Starts the Inverters
On Board Inverter
8 9 10
6 4 1
Local and Global Dimming
P203
6 8 8
12V/24V Regulators
50V
BACKLIGHTS To Panel Backlights 120Hz Manipulates Backlight LEDs Low = Bright LCD PANEL
P201 Stand By 3.5V 12V 24V DRV ON
P832
Local M0_SCLK Dimming MO_M0SI, +SCL2/SDA2 L_VS
16 Blocks
Local and Global Dimming P-DIM1 (PWM-DIM) Pulse Width Dimming Global Dimming
Manipulated by: Cust Menu for Backlight and Picture Content Manipulate P-DIM
Note 1: 12V SOURCE FOR: IC501 0.9V Core IC503 Power Det IC506 5V_USB IC507 5V_Normal IC505 3.3V_Normal IC5401 1.26V_FRC IC5402 3.3V_FRC Note 2: 24V SOURCE FOR: IC1702 Audio Amp IC502 Power Det Q1002 Wireless PWR
At point 3 TV is in Stand-By state. Energy Star compliant. 0 .1 Watts
Video
PWR_ON
PWM-DIM
2
P502
3.5V_ST 2 5 Other Regs Power On/Off1/2 5
9~12
5
1
6
17 19 21
6
2~4
8
18
9
22
Globar Dimming
10
3 5 8
Voltages for the Panel
P3503
Inverter On
Q502
MAIN BOARD
See Note 2:
PWM-DIM
VCC 3.3V, VDD 16.7V, VGL_I -5V, VGH 28V, P-VDD 16V
See Note 1:
Q507
Panel VCC 12V
T-CON PWB
12V LVDS 7
12V Q504 8 INV_CTL
Q501 5 RL_ON
Q506-7
7 7
Reset Generator C608 R644
2 3
10
7 4 Video Processor IC101 FRC IC5201
P1501 P1502 P901
Model 1_Opt1 Panel Control Microprocessor IC602 Key 1 or IR
After Mute Released LVDS Video 9
Tru-Motion LVDS Video
Ft IR / Soft Touch Key Remote or Power Button Key
49
June 2011
LCD-DV 47LW5600
47LW5600 Television Turn On Commands Circuit Drawing

7
To DC to DC Conv T-CON
Panel_Vcc (12V)
11.94V
Q507
11.97V
S G
1.8V
R558 10K
R555 22K
+12V L511
R559 1.8K L507

0V
Q506
0.68V
Q505
0V
R553
47K
6 3
PWR_ON 24V
L509
SMPS P201
1 2 3 4 5 6 7 8 3.4V 24.19V 24.19V 24.19V Gnd Gnd Gnd Gnd 3.55V 3.55V 3.55V 3.55V Gnd Gnd Gnd n/c 11.92V 3.26V 11.92V n/c 11.92V 0.2V~3.3V n/c n/c
MAIN P502
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 n/c n/c n/c
+3.3V_Normal
3.35V
7 8
IC505
2 6
11.96V 3.47V
+12V
R542 10K
6
20
Panel_CTL Power On/Off 2_2
R605
100
PWR_ON +24V
L504
Power_On/Off2_2
IC602 Micro
IR
C519 0.1uF
4
2.62V
16
Q502
0V
0V
Q501
0.64V
R508
4.7K
R502
10K
RL_ON
2
36 RL_ON
7 1
R643
22 Model_Opt_1 11
1
SBY3.5V
9 10 11 12 13 14 15
1
+3.5V_ST
L503
3.5V
+3.5V_ST C508 0.1uF R644 47K R546

1K 3.28V
Reset C608 0.1uF
40
Reset Power Det 14 Key 1 25
5
IC8007 IC8008
C506 0.1uF +12V

L501 12V
8
12V
n/c DRV_ON
16 17 18 19 20 21 22 23 24
+3.3V_Normal
Q504
0V
INV_ON
8
10 R547 10K R228 22 AH17
Key 2 26
n/c
8 9
PWM-DIM_22 R526 0
R532
100
INV_CTL
9 PWM-DIM1
n/c ERR OUT
P-DIM: Digital Dimming (Variable)

3.51V p/p 3.54V p/p 3 5
IC101 BCM
P832
1 0V 0.1V 0.12V
P3503
8
PWM-DIM1 (PWM Dimming) can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Range 0.37V to 3.3V.
9
L_VS M0_SCLK M0_MOSI
R3508 33 R3506 33 R3507 33
E11 C17 C16
SMPS
6 3
IC5201 BCM
(Data) 3.56V p/p Data
50
June 2011
LCD-DV
47LW5600
Power Supply Board Low Voltage Test 1

AC Should not be applied at any time while adding jumpers or While unplugging connectors as damage to the circuit Board June occur. a) When AC is applied, the SMPS MUST be producing STBY 3.5V on pins 9, 10, 11 or 12 of P201. If 3.5V Standby is not being generated, the SMPS is defective and must be replaced. There is no need to continue with the next test. But, make sure AC is arriving at the connector SK101. (b) Unplug P502 on the Main Board to make insertion of the Jumpers easier. Use P502 Side to insert resistors TEST 1: (1) Add a jumper between (3.5V STBY) pin 7, 8, 9 or 10 and Pin 1 (PWR_ON). Apply AC. This will turn on the power supply, relay will click. a) Check that the 24V (24.41V) and 12V power supplies are turned on, P201 (12V pins 17, 19 and 21) P201 (24V pins 2, 3 and 4) 2 P202 (36V pins 1 and 12) AND P203 (pins 1 and 13) (2) Remove AC power
No Backlights during this test
Pin 1 is the Brown Wire
51
June 201 LCD TV 1
47LW56000
Power Supply Board Backlights Test 2

Continue if the 1st test was OK. Leave original jumper in place. (3) Add another jumper between (STBY_3.5V) pin 9, 10, 11 or 12 and Pin 18 (DRV_ON). (4) Apply AC Power. Simulating a Power and Backlight On command. Backlights Normal: a) If normal, th b kli ht should t ) l the backlights h ld turn on. SMPS OK, Inverter OK. Backlights Abnormal: a) Recheck all connections connections. b) Confirm the DRV_ON line pulling up to at least 3V. c) Check the connections to the Panel. If the DRV_On command is pulling up to 3V and the 45V is being g p g p g generated from C256 + leg, see the Inverter Section of the Power Supply for additional checks. Note: If either P202 or P203 is disconnected, the backlights will come on, The Error line will go high, then the backlights shut off in 4~6 seconds. REMOVE AC POWER:
Pin 1 is the Brown Wire
52
June 201 LCD TV 1
47LW56000
47LW5600 2 Sided Edge Lit Panel (V6) 2011

47" TWO SIDED EDGE 2011 (Rear View) LEDs
Block: VC-2D (EL69 Rivet) P203 pin 11 Block: VC-2C (EL68 Rivet) P203 pin 10 Block: VC-2B (EL67 Rivet) P203 pin 9 Block: VC-2A (EL66 Rivet) P203 pin 8 Block: VC-1D (EL65 Rivet) P203 pin 6 Block: VC-1C (EL64 Rivet) P203 pin 5 Block: VC-1B (EL63 Rivet) P203 pin 4 Block: VC-3A (EL70 Rivet) P202 pin 3 Block: VC-3B (EL71 Rivet) P202 pin 4 Block: VC-3C (EL72 Rivet) P202 pin 5 Block: VC-3D (EL73 Rivet) P202 pin 6 Block: VC-4A (EL74 Rivet) P202 pin 7 Block: VC-4B (EL75 Rivet) P202 pin 8 Block: VC-4C (EL76 Rivet) P202 pin 9 Block: VC-4D (EL77 Rivet) P202 pin 10
50V
Block Control Signals (Drive)
50V
Example Connector
Connector
50V P203 pin 1 and 13 B+ 8 blocks Block: VC-1A (EL62 Rivet) P203 pin 3
128 Total LEDs 2 Boards (Strips) 64 LEDs per/board
16 Total Blocks 8 Blocks per/board (8 on Left, 8 on Right) 8 LEDs per/block P202 or P203
1.39V Bright ~ 13.74V Dark
50V P202 pin 1 and 12 B+ 8 blocks
ONE STRIP (Board)
Global And Local Dimming Control
LED Drive Signal 50 IRE

Off On 14V p/p 2mSec
120Hz
Driver On SMPS
50V with a Diode Check using
One LED can be tested
1 Block
6.1V drop per/LED max white
a DVM. Forward biased, the LED should light.
53
June 2011
LCD-DV
47LW5600
50V Supply Backlight Driver Section of the SMPS
C257
C256
The Power Supply for the Backlights pp y g Can be checked at the (+) side of C256 or C257 or the Cathode of D253. Note: When the PWR ON command PWR_ON Arrives, this voltage will read 36V. When the DRV_ON command arrives This voltage will rise to 65V the fall quickly Down to 50V.
50V 50V
D253
50V Location: Top Center of the SMPS
54
June 201 LCD TV 1
47LW56000
P202 and P203 Backlight Driver Section of the SMPS Association with TPs
P203 P203
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Label LED+ n/c VC-1A VC 1A VC-1B VC-1C VC-1D n/c VC-2A VC-2B VC-2C VC-2D n/c LED+ TP C256+ n/a EL62 EL63 EL64 EL65 n/a EL66 EL67 EL68 EL69 n/a C256+ EL69 EL70 EL68 EL67 EL65 EL63 EL77 EL75 EL73 EL71 EL66 EL64 EL62 EL76 EL74 EL72
P202
1
Pin 1 2 3 4 5 6 7 8 9 10 11 12
P202
Label LED+ n/c VC-3A VC 3A VC-3B VC-3C VC-3D VC-4A VC-4B VC-4C VC-4D n/c LED+ TP C256+ n/c EL70 EL71 EL72 EL73 EL74 EL75 EL76 EL77 n/c C256+
P832
55
June 201 LCD TV 1
47LW56000
P202 / P203 Power Supply Connector Voltage and Diode Check

P202 White Plug "SMPS Board" To "Panel LEDs" Pin 1 2 3 4 5 6 7 8 9 10 11 12 Label LED+ n/c VC-3A VC-3B VC 3B VC-3C VC-3D VC-4A VC-4B VC 4B VC-4C VC-4D n/c LED+ TP C256+ n/c EL70 EL71 EL72 EL73 EL74 EL75 EL76 EL77 n/c C256+ Run 50V n/c *1.39V~13.74V *1 39V~13 74V 1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1 39V 13 74V *1.39V~13.74V *1.39V~13.74V n/c 50V Diode Check OL OL OL OL OL OL OL OL OL OL OL OL P203 Black Plug "SMPS Board" To "Panel LEDs" Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Label LED+ n/c VC-1A VC 1B VC-1B VC-1C VC-1D n/c VC-2A VC 2A VC-2B VC-2C VC-2D n/c / LED+ TP C256+ n/a EL62 EL63 EL64 EL65 n/a EL66 EL67 EL68 EL69 n/a / C256+ Run 50V n/c *1.39V~13.74V *1 39V~13 74V 1.39V 13.74V *1.39V~13.74V *1.39V~13.74V n/c *1.39V~13.74V *1 39V 13 74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V n/c / 50V Diode Check OL OL OL OL OL OL OL OL OL OL OL OL OL *White to Black screen
*White to Black screen
P203
50V
P202
*The drive signal changes due to the brightness level of the backlights. L b kli ht Low indicates Bright. Hi h i di t Di i di t B i ht High indicates Dim.
Diode Mode values taken with all Connectors Removed
56
June 201 LCD TV 1
47LW56000
P832 Local Dimming Drive Waveforms

P832 "SMPS" to P1601 "MAIN" Pin 1 2 3 4 5 6 7 8 Label VSYNC SDA SCL SIN Gnd L/DIM0_SCLK n/c Reverse Top Waveforms are 500uSec/div Bottom Waveforms are 100uSec/div
P832 Pin 2 SDA 3.3V p/p
P832 Pin 3 SCL 3.2V p/p
2mSec/div
P832 Pin 4 SIN 3.35V p/p P832 Pin 1 VSYNC 3.5V p/p
P832 Pin 6 SCLK 3.3V p/p
57
June 201 LCD TV 1
47LW56000
P832 Voltages and Diode Checks

P832 "SMPS" to P1601 "MAIN Board" Pin 8 7 6 5 4 3 2 1 Label Reverse n/c L/DIM0_SCLK Gnd SIN SCL SDA VSYNC STBY 0V 0V 0V 0V Gnd 0V n/c 0V Run 0V 3.25V 3.25V 0.12V Gnd 0.1V 0 1V n/c 0.1V Diode Check 1.91V OL OL Gnd OL OL OL OL P832 Connector
58
June 201 LCD TV 1
47LW56000
P201 Power Supply Connector Voltage and Diode Check

P201 Connector "SMPS Board" To P502 "MAIN Board" Pin 24 23 22 21 20 19 18 17 16 13-15 9-12 5-8 2-4 1
1 2 3
Label ERROR n/c PWM 12V n/c 12V DRV-ON 12V V-SYNC Gnd 3.5V Gnd 24V PWR-ON
STBY n/c n/c 0V 0V n/c 0V 0V 0V n/c Gnd 3.55V Gnd 0V 0V
Run n/c n/c 0.2V~3.3V 11.92V 11 92V n/c 11.92V 3.26V 11.92V n/c Gnd 3.53V Gnd 24.19V 3.4V
Diode Check 2.03V n/c OL 0.48V 0 48V n/c 0.48V OL 0.48V n/c Gnd 2.63V Gnd 1.09V 1.15V
P201 Connector
Odd pins are on top row
(1) PWR_ON Pi 1 t PWR ON Pin turns on the SMPS which send 12V and th hi h d d 24V to the Main. The 50V Power Supply turns on too, but only generates 36.7V at this time.
(3) PDIM1 Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor g g g (room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V. . P-DIM1 3.66V 3 66V p/p 50IRE
59
June 201 LCD TV 1
47LW56000
SK100 and AC Fuse Power Supply Voltage and Diode Check

SK100 "SMPS" to AC IN Pin EL1 F100 5A/250V AC IN EL3 Label L N STBY Run Diode Check OL OL
120Vac
AC Voltage Readings (From Hot Ground) Pins 1 and 2 for STBY and RUN.
F100
F100 (Diode Check)
Red or Black Lead on Fuse (Open) Other Lead on Hot Ground
Bottom Left of SMPS
SK100 60 June 201 LCD TV 1 47LW56000
F101 and F103 Power Supply Voltage Checks
F101 3.15A/250V From Hot Gnd STBY 399V Run 398.5V
F501 1.6A/250V From Hot Gnd STBY 397V Run 396.5V
If the set was on and then turned off, the voltage takes a while to bleed down.
61
June 201 LCD TV 1
47LW56000
MAIN BOARD SECTION

The Main board receives its operational B+ from the Power Supply via P502. There are two LVDS cable feeds that are output to the T-CON (TFT Driver). These carry the duel 24 bit LVDS Video and TruMotion Video equaling a 120Hz video signal. These signals have already been prepared for the T-CON board. The Main board also includes the Frame Rate Converter for 3D, Tuner, Audio and Audio/Video inputs and selection circuits.
Input Voltages from SMPS. STAND-BY STAND BY STBY 3.5V (P502 pins 9~12) The Main board also develops several B+ sources on the board. STAND-BY VOLTAGES 3.3V_ST (Direct from SMPS through L503). LVDS Panel_VCC (12V Not generated, but switched by Q507 from the 12V arriving f b Q 0 f h i i from the SMPS) h SMPS). TUNER TU2101 and VSB CIRCUIT 5V_TU (Made from 5V_Normal through L2101 / 4) 3.3V_TU (Made from 3.3V_Normal L2103). 1.26V TU IC2103 (Made from 3.3V_TU). 1.26V_TU 3 3V TU) AUDIO IC1702 3.3V_AU_AVDD (Made from 3.3V_Normal). 3.3V_DVDD (Made from 3.3V_Normal). 1.8V (Made from 3.3V_Normal). 24V (Direct from SMPS through L504). GENERAL 5V_Normal IC507 (Made from 12V In). 3.3V_Normal IC505 (Made from 12V In). 5V USB IC506 (Made from 12V In). BCM IC101 Video Processor 3.3V_ST (Direct from SMPS through L503). 2.5V_BCM52230 (IC504) D1.5V_DDR (IC508 ) 0.9V_CORE (IC501) Frame Rate Converter (IC5201) FRC 1.26V_FRC (IC5401) 3.3V_FRC (IC5402), 1.5V_FRC (IC5403) HDMI SELECTOR VOLTAGES (IC701) 3.3V_HDMI (From 3.3V_Normal through L701) RUN 12V (P502 pins 17, 19 and 21). 24V (P502 pins 2~4).
62
June 201 LCD TV 1
47LW56000
Main Board Layout

P502 To SMPS P1702 To Speakers P3503 To SMPS P101 n/c IC1702 Audio
p/n: EBR72948402 AUSYLHR p/n: EBR73145901 AUSYLJR p/n: EBR72948404 AUSYLUR VIDEO PROCESSOR IC101 Is under a Heat Sink. It runs Hot Hot. This is normal. USB 1 USB 2 See next page for component identification HDMI 4 Wireless Remote HDMI 3
P1502 To T-CON
IC5201 FRC IC101 BCM P601 n/c IC602 Micro
IC102 NAND FLASH
P1501 To T-CON
P901 To Ft. IR P1302 To Motion Remote RS232 n/c LAN RGB RGB Audio
Component 1 Composite 1 Tuner TU2101 Optical RF Component 2 Composite 2
HDMI 2
HDMI 1 Headphones Component In C

These connectors are Mini plug type
63
June 201 LCD TV 1
47LW56000
47LW5600 Main Board (Front and Back Side) Component Layout

P502
P201 "SMPS Board" To P502 "MAIN Board" Pin Label STBY Run Diode Check 1 PWR-ON 0V 3.4V OL 2-4 24V 0V 24.19V OL 5-8 Gnd Gnd Gnd Gnd 9-12 3.5V 3.55V 3.53V 1.16V 13-15 Gnd Gnd Gnd Gnd 16 V_Sync 0V 0V OL 17 12V 0V 11.92V 2.32V 18 DRV-ON 0V 3.26V 1.62V 19 12V 0V 11.92V 2.32V 20 n/c n/c n/c OL 21 12V 0V 11.92V 2.32V (1) 22 PWM 0V 0.2V~3.3V OL 23 n/c n/c n/c OL 24 ERR_OUT n/c n/c OL P901 Connector "MAIN Board" To "IR Board"
C E C B E B
P3503
RL_ON Drivers
IC503 Power Det (12V) Q1701
C E B
Q504
B C E
Q502 Q501 3 2 IC502 Power Det (24V) 1

3 1 2
P101 N/C
0.9V FET Switch
INV_CTL Driver
L1704 L1703
Audio Mute
+0.9V_CORE
Q503 IC501
L505
3.3V_ Normal
5V_Normal
IC507 IC506
5V_USB
IC505 Q508
IC1702
L1708
Audio Amp
0.9V FET Switch
P1702
IC5402
+3.3V_FRC NAND FLASH IC102
L1707
P1502
IC5301
+1.5V_FRC
IC5403
USB2 EDID
DDR
IC5201 FRC
X5201
B E C
SPI Flash IC5202 IC401 DDR
IC1203 IC103
NVRAM
BCM IC101
RGB_ Q102 DDC_SCL

G B D D S S G B
IC402 DDR IC508

+1.5V_DDR
Video Processor
RGB_ DDC_SDA Q101 Earphone Amp
IC1204
USB1 EDID Q710 CEC
G B S
Pin Label 1 SCL 2 SDA 3 Gnd 4 KEY 1 5 KEY 2 6 3.5V_ST 7 Gnd 8 LED_B/BUZZ 9 IR 10 Gnd 11 +3.3V_Normal 12 LED_R/BUZZ 13 Gnd 14 S/T_SCL 15 S/T_SDA
STBY 3.55V 3.55V Gnd 3.33V 3.33V 3.55V Gnd 0V 1.48V Gnd 0.0V 0V Gnd 3.55V 3.55V
Run 3.49V 3.49V Gnd 3.28V 3.28V 3.49V Gnd 0V 1.47V Gnd 3.33V 0V Gnd 3.49V 3.49V
Diode Check OL OL Gnd OL OL OL Gnd OL OL Gnd OL OL Gnd OL OL
Q505
B E
+1.26V_FRC
IC701
B E C
Q506
D
G S
IC5401
Panel VCC Swith
X601
A1 A2
Q801
Q507
+2.5V_BCM35230
IC804
HDMI Selector
D713 D711
C
A1 A2
P1501
IC504
P601 N/C
IC601 MICRO IC602

C E B E B
EEPROM
MAIN BOARD
D C
Q904 Q906
C C
X602 Q901 BB E SW1 C Q902 E
p/n: EBR72948402 AUSYLHR p/n: EBR73145901 AUSYLJR Q1001 Wireless Dongle Switch p/n: EBR72948404 AUSYLUR
Q1002
G S
D708
A1 A2
B E
RS232
P901
IC803
SW1 Microprocessor Reset
Grayed out components are on the back
TU2101 TUNER
IC801 IC802
PC EDID
A1 A2
18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V 12. GND 11. CVBS 10. NC 9. SIF 8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
18
B E C B E C
TUNER 18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V 12. GND 11. CVBS 10. NC 9. SIF 8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
Q2105 Q2104
IC2103
3 2 1 2
C
A1 A2
D710
P1302
+1.26V_TU
D707 1
A1 A2
C PC Data D810
64
June 2011
LCD-DV
47LW5600
47LW5600 Main Board (Front) Component Layout

C
Q502 Q501
E C B
E B
RL_ON Drivers
P3503
0.9V FET Switch
P101 N/C
P502
L1704 L1703
Audio Amp
+0.9V_CORE
Q503 IC501
L505
3.3V_ Normal
5V_Normal
IC507 IC506
5V_USB
IC505 Q508
12.2V Each Pin
IC1702
L1708
0.9V FET Switch
P1702
IC5402 IC5403
+3.3V_FRC NAND FLASH IC102
L1707
P1502
IC5301
+1.5V_FRC
USB2 EDID
DDR IC401 DDR IC402 DDR IC508

+1.5V_DDR +2.5V_BCM35230
BCM IC101
IC1203 IC103
NVRAM
IC5201 FRC
X5201
IC1204
Video Processor Earphone Amp USB1 EDID
P1501
IC5401
+1.26V_FRC Microprocessor
X601
IC701 IC804
HDMI Selector
IC504
P601 N/C
IC602
MAIN BOARD
p/n: EBR72948402 AUSYLHR p/n: EBR73145901 AUSYLJR Wireless Dongle Switch p/n: EBR72948404 AUSYLUR
D C
P901
X602 C Q901 B B E SW1 C Q902 E
Q1002
Q1001
RS232
SW1 Microprocessor Reset
IC803
P1302
IC801
PC Data
TU2101 TUNER
IC802
PC EDID
18
IC2103
3 2 1 2
+1.26V_TU
1
65
June 2011
LCD-DV
47LW5600
47LW5600 Main (Front Side) Component Voltages
IC103 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC501 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] IC504 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC505 Pin [1] [2] [3] [4] [5] [6] [7] [8]
NVRAM for USB n/c 0V 3.34V 0V 3.22V 3.22V 0V (Gnd) 3.34V +0.9V_CORE DC to DC 3.17V 0.59V 0.44V 11.95V 0V 5.33V 4.6V 5.81V 0.95V 1.36V +2.5V BCM Regulator n/c 4.92V (En) 3.47V (In) 3.49V (Ctl) n/c 2.57V (Out) 0.6V 0V (Gnd) (+3.3V_NORMAL) Regulator 0V (Gnd) 11.96V (In) 0V (Gnd) 0.8V 0.79V 3.47V (PWR On/Off2_2) 3.35V (Out) 3.35V (Out)
IC506 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC507 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC508 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q901
Switched 5V for USB 2 0V (Gnd) 11.98V (In) 0V (Gnd) 0.79V 3.48V 3.48V (PWR On/Off2_1) 4.96V (Out) 4.96V (Out) (+5V_NORMAL) Regulator 0V (Gnd) 11.98V (In) 0V (Gnd) 0.79V 3.48V 3.48V (PWR On/Off2_1) 4.96V (Out) 4.96V (Out) (+1.5V_DDR) Regulator 3.46V n/c 3.46V (In) 3.49V (PWR On/Off1) 0V (Gnd) 3.31V 0.79V 1.5V (Out) IR Buffer 2nd
IC801 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] IC802 Pin [1] [2] [3] [4] [5] [6] [7] [8]
RGB Data Buffer 1.81V 1.81V 3.72V 1.8V 1.8V n/c (4.44V) 0V (Gnd) n/c (4.43V) n/c (1.79V) n/c (1.79V) 3.72V 1.81V 1.81V 5V (Vcc In) EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.73V 4.73V 4.73V 4.73V (Vcc In)
IC803 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC1203 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC1204
RS232 Routing 3.5V 5.64V 0V 0V (-5.56V) (-5.59V) n/c (5.64V) n/c (0V) n/c (3.49V) n/c (0V) n/c (3.34V) 3.48V 0V (-5.59V) 0V (Gnd) 3.5V (Vcc In) EDID Data PC 0V (Gnd) 4.96V (Vcc In) 4.96V (Vcc In) 3.34V (USB Ctl2) 3.17V 4.96V (Out) 4.96V (Out) n/c (0V) EDID Data PC 0V (Gnd) 4.96V (Vcc In) 4.96V (Vcc In) 3.34V (USB Ctl1) 3.17V 4.96V (Out) 4.96V (Out) n/c (0V)
IC2103
(+1.26V_TU) Pin Regulator [1] 0V (Gnd) [2] 1.27V (Out) [3] 3.33V (In) (+1.26V_FRC) Regulator 0V (Gnd) 11.85V (Vcc In) 0V (Gnd) 0.8V (FB) 0.7V 3.29V (Enable) 1.29V (Out) 1.29V (Out) (+3.3V_FRC) Regulator Under Shield Under Shield Under Shield Under Shield 0.8V 3.45 (PWR On/Off2_2) 3.3V 3.3V
Q501
RL_ON (PWR_On) Pin 1st Driver B 0.64V C 0V E Gnd PWR_ON Pin Switch [1] 3.5V (In) [2] 0.67V [3] 2.62V (Out) 0.9V FET Switch 0.95V 0.95V 0.95V 1.36V 11.96V 11.96V 11.96V 11.96V 0.9V FET Switch 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.6V 0.95V 0.95V 0.95V 0.95V
IC5401 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC5402 Pin [1] [2] [3] [4] [5] [6] [7] [8]
Q502
Q503 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q508 Pin [1] [2] [3] [4] [5] [6] [7] [8]
Pin B 0.02V C 3.48V E Gnd Q902 Pin B 0.57V C 0.02V E Gnd
Wireless Vcc Pin Driver B 0.02V C 24.5V E Gnd On when wireless dongle connected Wireless Vcc Pin Switch S 24.5V G 24.5V D 0V On when wireless dongle connected Q1002
Q1001
IR Buffer 1st
Pin [1] [2] [3] [4] [5] [6] [7] [8]
66
June 2011
47LW56500 LCD-DV
47LW5600 Main Board (Back Side) Component Layout

Power Det (24V) IC502
2 3 1 2 3 1
Q504
B E C
Power Det (12V)
IC503
INV_CTL Driver
MAIN BOARD
p/n: EBR71850702 p/n: EBR73146501 p/n: EBR71850705
Q1701
C B E
Amp_Mute
SPI Flash IC5202 RGB_DDC_SCL RGB_DDC_SDA Panel Vcc Drivers

D E B C B E S G C
Q102 Q101
B S G B
G D D S
Q710
B S G D
CEC
A1 A2
D713 D711
C
A2 A1
Q801 Side HP Mute

E B C
Q505 Q506
D708
C
A1 A2
TU2101 TUNER
18
D710
C
A2 A1
TU_CVSB Q2105
E B C E B C
Digital Video
Q507 Panel Vcc Switch IC601

EEPROM
Q904
C C B E E B
Analog Video Audio Tuner Data Tuner Clock Tuner B+
Q906
IR Pass
D707
C
A1 A2
Q2104 TU_SIF
D810
C
A2 A1
67
June 2011
LCD-DV
47LW5600
47LW5600 Main (Back Side) Component Voltages
IC502
Power Det Gen Pin (For +12V) [1] 0V (Gnd) [2] 3.8V (In) [3] 3.73V (Out) Power Det Gen Pin (For +24V) [1] 0V (Gnd) [2] 3.7V (In) [3] 3.73V (Out) EEPROM Micro 0V (Gnd) 0V (Gnd) 3.49V 0V (Gnd) 3.49V 3.49V 0V (Gnd) 3.50V (Vcc In) SPI FLASH 0.43V 3.29V 3.29V 0V (Gnd) ?? ?? 3.29V 3.29V (3.3V_FRC in)
Q101 Pin [B] [G] [S] [D] Q102 Pin [B] [G] [S] [D] Q504 Pin B C E Q505
IC503
RGB_DDC_SDA FET Buffer 0V (Gnd) 3.3V 4.74V 3.34V RGB_DDC_SCL FET Buffer 0V (Gnd) 3.3V 4.74V 3.34V INV_CTL (Drv_On) Driver 0V (INV ON) En 3.28V (Out) Gnd PANEL_VCC
Q710 Pin [B] [G] [S] [D] Q801
CEC Remote HDMI CEC 3.47V 3.51V 3.47V 3.49V Earphone Mute
Q2106
Tuner Video Pin (Analog) Buffer B 3.67V C 0V (Gnd) E 4.35V 5V Pull-Up to Pin DDC_SCL/SDA_1 A1 4.96V C 5V A2 0V 5V Pull-Up to Pin DDC_SCL/SDA_3 A1 4.96V C 5V A2 0V 5V Pull-Up to Pin DDC_SCL/SDA_2 A1 4.96V C 5V A2 0V 5V Pull-Up to Pin DDC_SCL/SDA_4 A1 4.96V C 5V A2 0V Bias for Q710 Pin HDMI CEC A1 0V C 3.45V A2 3.5V
D810
5V Routing to Pin IC802 RGB EDID A1 4.73V C 5.01V A2 0.07V
D707 Pin B 0V C 3.35V E Gnd Q904 Pin B C E
IC601 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC5202 Pin [1] [2] [3] [4] [5] [6] [7] [8]
D708 IR Wireless Pass 2nd Driver 0.02V 3.48V Gnd D710

Control 1st Driver Pin B 0V C 0.68V E Gnd
Q906
IR Wireless Pass Pin 1st Driver B 0.57V C 0V E Gnd AMP_MUTE Pin Pin 19 IC1702 B 0V C 3.36V E Gnd Tuner SIF Pin (Sound) Buffer B 0.23V C 0V (Gnd) E 0.93V
D711
Q506
PANEL_VCC
Control 2nd Driver Pin B 0.67V C 0V E Gnd
Q1701
D713
Q507 Pin S G D
PANEL_VCC Switch 11.97V (In) 1.8V (Enable) 11.94V (Out)
Q2104
68
June 2011
47LW5600 LCD-DV
Main Board X601, X602 and X5201 Crystal Checks

X5201 1.71V 1 71V 1.71V 1 71V X602
Either leg 32.768KHz
No Signal 3V p/p pp
24Mhz
Runs when set is on
1.18V
2.28V p/p pp
Runs all The time
3.51V p/p
2.09V
Bottom leg g
IC601 Micro Crystal Either leg
X601 1.57V 2.31V / 2 31V p/p

Runs when set is on
3.3V / 3 3V p/p 2V
10Mhz
Runs all the time
MAIN Board
69
June 201 LCD TV 1
47LW56000
Audio Amplification for Speakers Information

Use speaker out to test for defective Audio Amp IC1702 Note: (Normal Audio B+) 12 09V on each pin (Normal, 12.09V pin.
IC1702 VOLTAGES 3.3V_AU_AVDD pin 13 3.3V_DVDD pin 27 All made from 3.3V_Normal Right Channel: 24V pin 34, 35 (R-) 24V pin 40, 41 (R+) Left Channel: 24V pin 44, 45 (L-) 24V pin 2, 3 (L+) RR+ LL+ IC1702
(1)
Amp _Reset pin 25
Q1701 Back side of the board is (Mute) Active Low. 3.3V_ST Collector to AMP_MUTE_PDN Pin 19
70
June 201 LCD TV 1
47LW56000
P1702 Main Board Connector to Speakers Voltage and Diode Check

P1702 Connector "Main" To "Speakers" Main Speakers Pin 1 2 3 4 Label SPK-R(-) SPK-R(+) SPK R( ) SPK-L(-) SPK-L(+) SBY 0V 0V 0V 0V Run 12.09V 12.09V 12 09V 12.09V 12.09V Diode Check Open Open O Open Open RR R+ LL+ P1702
71
June 201 LCD TV 1
47LW56000
P502 Main Board Connector to Power Supply Voltage and Diode Check
P502 "MAIN Board" Connector To P201 "SMPS Board" P502
Pin 1 2-4 5-8 9 12 9-12 13-15 16 17 18 19 20 21 22 Label PWR-ON 24V Gnd 3.5V_ST 3 5V ST Gnd GND/VSYNC 12V INV-ON INV ON 12V A-DIM 12V PDIM-1 n/c Err OUT STBY 0V 0V Gnd 3.55V 3 55V Gnd n/c 0V 0V 0V n/c 0V 0V n/c n/c Run 3.4V 24.19V Gnd 3.53V 3 53V Gnd n/c 11.92V 3.26V 3 26V 11.92V n/c 11.92V 0.2V~3.3V n/c n/c Diode Check OL OL Gnd 1.16V 1 16V Gnd OL 2.32V 1.62V 1 62V 2.32V OL 2.32V OL OL OL
Odd Pins Top Row
23 24
(1)
PDIM Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Range 0.2V to 3.3V.
P-DIM1 P DIM1 3.66V p/p 50IRE
72
June 201 LCD TV 1
47LW56000
P1501 Main to T-CON Voltage and Diode Check

P1501 Connector "MAIN Board" To "T-CON"
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label n/c 3D_SYNC n/c Run n/c 0V n/c Diode Check 1.15V OL n/c OL OL OL OL n/c n/c OL Gnd 1.13V 1.13V 1.13V 1.13V 1.13V 1.13V 1 13V Gnd 1.13V 1.13V Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Label Gnd TXA3N TXA3P TXA4N TXA4P Gnd TXB0N TXB0P TXB1N TXB1P TXB2N TXB2P Gnd Run Gnd 1.27V 1.15V 1.33V 0.98V Gnd 1.24V 1.14V 1.27V 1.14V 1.31V 1.10V Gnd Diode Check Gnd 1.13V 1.13V 1.13V OL Gnd OL 1.13V 1.13V 1.13V 1.13V 1.13V 1.13V Gnd 1.13V 1.13V Gnd 1.13V 1.13V 1.13V Pin 41 42 43 44 45 46 47 48 49 50 51 Label TXB4P Gnd Gnd Gnd Gnd Gnd n/c Run 0.99V Gnd Gnd Gnd Gnd Gnd n/c Diode Check 1.13V Gnd Gnd Gnd Gnd Gnd n/c 0.89V 0.89V 0.89V 0.89V
SDA2_3.3V 3.31V SCL2_3.3V 3.31V FRC_RESET 2.95V LVDS_SEL n/c n/c PANEL_CTL Gnd TXA0N TXA0P TXA1N TXA1P TXA2N TXA2P Gnd TXACLKN TXACLKP 0V n/c n/c 0V Gnd 1.26V 1.15V 1.26V 1.14V 1.27V 1.13V 1 13V Gnd 1.16V 1.23V
BIT_SEL 2.37V
Panel_VCC 11.9V Panel_VCC 11.9V Panel_VCC 11.9V Panel_VCC 11.9V
P1501
TXBCLKN 1.16V TXBCLKP 1.23V Gnd TXB3N TXB3P TXB4N Gnd 1.34V 1.07V 1.41V
There are no Stand-By Voltages for the Connector Diode Mode values taken with all Connectors Removed
73
June 201 LCD TV 1
47LW56000
P1502 Main to T-CON Voltage and Diode Check

P1502 Connector "MAIN" To "T-CON"
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label n/c n/c n/c n/c n/c n/c n/c n/c Gnd TXC0N TXC0P TXC1N TXC1P TXC2N TXC2P Gnd Run n/c n/c n/c n/c n/c n/c n/c n/c Gnd 1.25V 1.15V 1.26V 1.13V 1.29V 1.11V Gnd Diode Check n/c n/c n/c n/c n/c n/c n/c n/c Gnd 0.85V 0.85V 0.85V 0.85V 0.85V 0.85V Gnd 0.85V 0.85V Gnd 0.85V Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Label TXC3P TXC4N TXC4P Gnd Gnd TXD0N TXD0P TXD1N TXD1P TXD2N TXD2P Gnd Run 1.07V 1.40V 0.99V Gnd Gnd 1.24V 1.15V 1.27V 1.12V 1.32V 1.07V Gnd Diode Check 0.85V 0.85V 0.85V Gnd Gnd 0.85V 0.85V 0.85V 0.85V 0.85V 0.85V Gnd 0.85V 0.85V Gnd 0.85V 0.85V 0.85V 0.85V Gnd Gnd
P1502
TXDCLKN 1.17V TXDCLKP 1.23V Gnd TXD3N TXD3P TXD4N TXD4P Gnd Gnd Gnd 1.31V 1.07V 1.39V 1.02V Gnd Gnd
TXCCLKN 1.17V TXCCLKP 1.23V Gnd TXC3N Gnd 1.31V
There are no St d B Th Stand-By Voltages for the Connector Diode Mode values taken with all Connectors Removed
74
June 201 LCD TV 1
47LW56000
P901 Main Board to (Ft. IR/Intelligent Sensor) Voltage and Diode Check
P901 Connector "MAIN Board" To "IR Board"
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
(1) Clock (2) IR (3) (3)
Label
(1) (1)
STBY 2.9V 2.92V Gnd 3.26V 3.26V 3.55V Gnd 0V 1.48V Gnd 0.35V 0V Gnd 3.55V 3 55V 3.55V
Run 3.49V 3.49V Gnd 3.28V 3.28V 3.49V Gnd 0V 1.45V Gnd 3.34V 0V Gnd 3.49V 3 49V 3.49V
Diode Check 3.28V 3.28V Gnd 1.88V 1.88V 1.15V Gnd OL OL Gnd 0.53V 2.67V Gnd 1.86V 1 86V 1.86V
SCL SDA
P901
Gnd KEY 1 KEY 2 3.5V_ST Gnd LED_B/BUZZ

(2)
IR
Gnd +3.3V_Normal LED_R/BUZZ Gnd S/T_SCL S/T SCL S/T_SDA
& Data pulses only present when Intelligent Sensor is turned on. (3.6V p/p) pulses (2V p/p) (3) Clock & Data pulses only present when Set is turned on or Off. (3.9V p/p)
75
June 201 LCD TV 1
47LW56000
P1302 Main to Motion Remote (Voltage and Diode Check)

P1302 Connector "MAIN Board To "Motion Remote MAIN Board" Motion Remote" Pin 1 2 3 4 5 6 7 8 9 10 11 12 Label 3.5V_Normal Gnd M_Remote_RX M_Remote_TX Reset R t DC_MRemote DD_MRemote Gnd GPI0-O GPI0-1 GPI0-2 GPI0-3 STBY 0.35V Gnd 0.35V 0.35V 0.35V 0 35V 0.35V 0.35V Gnd 0V 0V 0V 0V Run 3.34V Gnd 3.33V 3.33V 3.33V 3 33V 3.33V 3.33V Gnd 0V 0V 0V 0V Diode Check 0.53V Gnd OL OL 2.41V 2 41V 2.38V Gnd Gnd OL OL OL OL
1
P1302
76
June 201 LCD TV 1
47LW56000
JK1001 Main Wireless Media Box Dongle Jack (Voltage and Diode Check)
JK1001 "MAIN Board" To "Wireless Media Box Dongle"
Pin 1-6 7 8 9 10 11 12 13 14 15 16 17 18 19-20 Label *24V Detect Interrupt Gnd n/c Gnd I2C_SCL _ I2C_SDA Gnd Wireless_RX Wireless_TX Wi l TX Gnd IR Gnd STBY 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0.67V 0V Run 24.19V 0.3V 3.3V Gnd 3.3V Gnd 3.3V 3.3V Gnd 3.3V 3.3V 3 3V Gnd 3.3V Gnd Diode Check OL OL OL Gnd OL Gnd 1.76V 1.73V Gnd OL OL Gnd OL Gnd 1 Diode Mode values taken with all Connectors Removed
Wireless Media Box Dongle must be plugged in for these voltages. JK1001 Jack J k
Voltages with Wireless Media Box Dongle plugged in. Use Media Box Dongle side to read voltages. Remove cover, (see Wireless Media Box training manual for details). *24.19V Switched from Q1002 Drain front side of the board. Q1002 turned on by Q1001 front side of the board board. Q1001 turned on by Microprocessor pin 38.
77
June 201 LCD TV 1
47LW56000
T-CON (TFT DRIVE) SECTION
TFT-LCD Controller Board

The T-CON is located at the bottom of the panel under the Stand Bracket. 12V is supplied to the T-CON Board from the Main Board via connector CN1 (easily measured at fuse F1). IC UC1 receives 24 bit LVDS video signals from the Main Board t B d at CN1 and CN2 which it processes i t TFT D i Si d hi h into Drive Signals. It d li l delivers it output its t t signals through connectors CN4 and CN5 to control the LCD Panel. US1, U3 and U6 are DC to DC converters which develop the Panels driver voltages. 16.48V, 3.3V, 5V d 29V. Th 16 48V 3 3V -5V and 29V These voltages can b read at the ribbon connector or at test lt be d t th ibb t tt t locations on the board which are identified on the following pages.
Stand Bracket
T-CON
78
June 201 LCD TV 1
47LW56000
T-CON (TFT Drive) Board Layout
The two screws shown in the picture are for the Service Position. They would have been removed when removing the shield. Be sure to reinstall them if servicing the T-CON board.
79
June 201 LCD TV 1
47LW56000
47LW5600 T-CON (TFT Drive) with (Shield Removed) Components Identified

Warning: T-Con Board under shield. Be sure to reinsert screws before operating set with shield removed.
PANEL TEST To run the T-CON Panel Test, remove the LVDS cables. Jump 12V to the 12V fuse. Jump VCC 3.3V to pin 44 on CN1. White, Red, Blue, Green and Black patterns show on screen.
(11.76V) (11.76V)
LVDS
To Main
U5
LVDS
12V
5) Gnd 6) Gnd 7) Gnd 8) Gnd
4) 3.31V 3) 3.3V 2) 2.95V 1) 3.3V
12V
(8.7V) HVDD
V 12
Gnd
CN2
(3.35V)
Gnd
Gnd
Gnd
(11.76V)
CN1
F1 3A/125V Panel Test TP 44
L1 D6
L3
U5 FL2
Gnd
L2
(3.31V)
D7
Gnd
VCC 3.3V
UC1
-2.8V Pin 10
Note: VGHEVEN and VGHODD swap once a second Pin 13
VDD 16.48V
Pin 18 (24.9V) 1
2 3
US1 US1 Q12 Q11 2

2 3 2 1
Pin 15
VST -5V
U3
VGHEVEN 29V
U6
P-VDD 16.37V Pins 7-8
-2.8V 2.1V
D1
D3 D2
(29.1V)
1) 28.4V 2) 29V 3) 29.1V
3) Gnd 2) 1.6V 1) 0.6V
VGHR 29V Pin 11 VGHF -5V Pin 12 VGHODD -4.9V

C106
VST VGLI VGHEVEN VGHODD VGHF VGHR
FL1
CN4
VGL_I -5V
C101 C102
CN5
VDD 16.47V
C105
Pin 52 VGHR Pin 51 VGHF Pin 50 VGHODD Pin 49 VGHEVEN
29V -5V -5V 28V
Pin 48 VGL_I Pin 47 VST Pin 35 VCC Pin 40,41 VDD
-5V -5V 3.3V 16.48V
TO TFT MODULE
29V -5V -5V 28V
-5V -5V 3.3V 16.48V
Note: VGHEVEN and VGHODD swap once a second
Other Voltages from U6 to the Panel with no silk screen labels: U6 pin 11: (13V) to CN4 pin 3, CN5 pin 58 U6 pin 12: (12.1V) to CN4 pin 4, CN5 pin 57 U6 pin 13: (10.25V) to CN4 pin 5, CN5 pin 56 U6 pin 14: (6.17V) to CN4 pin 8, CN5 pin 53 U6 pin 15: (4.3V) to CN4 pin 9, CN5 pin 52 U6 pin 18: (3.3V) to CN4 pin 10, CN5 pin 51 U6 pin 19: (2.65V) to CN4 pin 11, CN5 pin 50 U6 pin 20: (16.37V) to CN4 pin 40,41, CN5 pin 20, 21
80
June 2011
LCD-DV
47LW5600
T-CON (TFT Drive) Board Panel Test

Set up the Power Supply Test as in Test 2 (Shown on page 46). Do not apply AC at this time. Jump 12V from the SMPS to the T CON Fuse F1 (P201 pin 17 or 19 or 21) T-CON 51 44
Disconnect both LVDS Cables Jump 3.3V from the VCC TP to pin 44 of CN1 Note: The connector has hash marks to indicate steps of 5. The marks are one pin off. 5 is actually 6.
Apply AC to the Power Supply and Toggling patterns of White, Red, Blue, Green should appear on the screen
81
June 201 LCD TV 1
47LW56000
CN1 T-CON Connector CN1 to the Main PWB (Voltage and Diode Check)
CN1 "T-CON" to "MAIN Board" P1501 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label n/c 3D_SYNC n/c SDA2_3.3V SCL2_3.3V SCL2 3 3V LVDS_SEL n/c n/c PANEL_CTL Gnd TXA0N TXA0P TXA1N TXA1P TXA2N TXA2P Gnd TXACLKN TXACLKP Run n/c 0V n/c 3.31V 3.31V 3 31V 0V n/c n/c 0V Gnd 1.26V 1.15V 1.26V 1.14V 1.27V 1.13V Gnd 1.16V 1.23V Diode Check n/c OL n/c OL OL OL OL n/c n/c OL Gnd OL OL OL OL OL OL Gnd OL OL Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Label Gnd TXA3N TXA3P TXA4N TXA4P Gnd BIT_SEL TXB0N TXB0P TXB1N TXB1P TXB2N TXB2P Gnd Run Gnd 1.27V 1.15V 1.33V 0.98V 0 98V Gnd 2.37V 1.24V 1.14V 1.27V 1.14V 1.31V 1.10V Gnd Diode Check Gnd OL OL OL OL Gnd OL OL OL OL OL OL OL Gnd OL OL Gnd OL OL OL Pin 41 42 43 44 45 46 47 48 49 50 51 Label TXB4P Gnd Gnd Gnd Gnd Gnd n/c Panel_VCC Panel_VCC _ Panel_VCC Panel_VCC Run 0.99V Gnd Gnd Gnd Gnd Gnd n/c 11.9V 11.9V 11.9V 11.9V Diode Check OL Gnd Gnd Gnd Gnd Gnd n/c OL OL OL OL
FRC_RESET 2.95V
Bold labels are video signals. p Except 48~51 which are 12V CN1
TXBCLKN 1.16V TXBCLKP 1.23V Gnd TXB3N TXB3P TXB4N Gnd 1.34V 1.07V 1.41V
Hash marks in steps of 5. First hash mark is off by 1 pin. Starts on pin 6.
82
June 201 LCD TV 1
47LW56000
CN2 T-CON to the Main PWB (Voltage and Diode Check)

CN2 "T-CON" to "MAIN" P1502 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label n/c n/c n/c n/c n/c n/c n/c n/c Gnd TXC0N TXC0P TXC1N TXC1P TXC2N TXC2P Gnd Run n/c n/c n/c n/c n/c n/c n/c n/c Gnd 1.25V 1.15V 1.26V 1.13V 1.29V 1.11V Gnd Diode Check n/c n/c n/c n/c n/c n/c n/c n/c Gnd 0.85V 0.85V 0.85V 0.85V 0.85V 0.85V Gnd 0.85V 0.85V Gnd 0.85V Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Diode Mode values taken with all Connectors Removed Label TXC3P TXC4N TXC4P Gnd Gnd TXD0N TXD0P TXD1N TXD1P TXD2N TXD2P Gnd Run 1.07V 1.40V 0.99V Gnd Gnd 1.24V 1.15V 1.27V 1.12V 1.32V 1.07V Gnd Diode Check 0.85V 0.85V 0.85V Gnd Gnd 0.85V 0.85V 0.85V 0.85V 0.85V 0.85V Gnd 0.85V 0.85V Gnd 0.85V 0.85V 0.85V 0.85V Gnd Gnd G d
CN2
TXDCLKN 1.17V TXDCLKP 1.23V Gnd TXD3N TXD3P TXD4N TXD4P Gnd Gnd G d Gnd 1.31V 1.07V 1.39V 1.02V Gnd Gnd G d
Bold labels are video signals.
TXCCLKN 1.17V TXCCLKP 1.23V Gnd TXC3N Gnd 1.31V
83
June 201 LCD TV 1
47LW56000
FRONT (IR, INTELLIGENT SENSOR and POWER LED) SECTION

The Intelligent Sensor and IR board (located on the bottom left as viewed from the rear) contains the IR (Infrared Remote Sensor) and the Intelligent Sensor. This board also has the Soft Touch Key Board. The IR board receives it operating B+ pin 6 from the Main P901 (STBY 3.5V). The IR (Infrared) remote receiver can be measured (1.48V) at pin 9 of connector P901 on the Main board in Stand-By. During run pin 9 reads (1.47V). The IR pulses (2V p/p) are sent to the Main board and on to the Microprocessor (IC602) via pin 16. The Front Power LEDs are controlled by different Clock and Data lines which communicate with the LED Driver IC U1. These clock and data lines are from the Main board P901 pins 14 and 15 which are only active when the Power is turned on or off. The Soft Touch Keys are part of the IR board. Key 1 (pin 4) and Key 2 (pin 5) are output From Pat P901 on the Main Board, then to the Microprocessor 25 and 26 lines. The Intelligent Sensor communicates with the Micro Processor IC602 pins 3 & 4 via clock and data lines EEPROM_SCL EEPROM SCL and EEPROM_SDA arriving on connector P901 pins 1 and 2 on the Main board. EEPROM SDA board The Intelligent Sensor circuit receives its operational voltage when the set turns on via pin 11 (3.3V_Normal).
1 Front IR and Soft Touch Key Board p/n EBR72671301 To Main Board
Plastic Cover. Wire routing.
84
June 201 LCD TV 1
47LW56000
Gaining access to the Front IR/Key Board

The Front IR Item 510 on the parts breakdown is under a wire routing bracket Item 511. Disconnect the cable coming from the Main board and remove it from the wire holders in Item 511.
IR/Key board p/n: EBR72671301 Remove the Speaker by sliding it forward.
Speaker Wire routing bracket, Slide Right
Tab
Tab
Screw
Tab
Remove the one screw. Lift up on the three tabs at the top of Item 511 and pull th It ll the Item 511 slightly forward. li htl f d Lift Item 511 up and out.
85
June 201 LCD TV 1
47LW56000
Front IR Component Identification

See Disassembly section for gaining access to the IR/Key Board
Attached to the Front Frame IR/Key Board p/n: EBR72671301 Front IR/Key F t IR/K Board Exposed
Key Board Decoder
Output: 1.48V O G V Infrared Receiver IC2 Ground Input Voltage 3.55V
J1
1 Power LEDs
86
June 201 LCD TV 1
47LW56000
J1 Front IR/Soft Touch Key Board Voltage and Diode Check

J1 "IR Board" To P901 "Main Board" Pin Pi 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
(1) Clock
Label L b l SCL SDA Gnd KEY 1 KEY 2 3.5V_ST Gnd LED_B/BUZZ IR Gnd +3.3V_Normal LED_R/BUZZ Gnd S/T_SCL S/T SCL S/T_SDA
STBY 3.55V 3.55V Gnd 3.33V 3.33V 3.55V Gnd 0V 1.48V Gnd 0V 0V Gnd 3.55V 3.55V
Run R 3.49V 3.49V Gnd 3.33V 3.33V 3.49V Gnd 0V 1.47V Gnd 3.33V 0V Gnd 3.49V 3.49V
Diode Ch k Di d Check OL OL Gnd OL OL OL Gnd OL OL Gnd OL OL Gnd OL OL
J1
& Data pulses only present when Intelligent Sensor is turned on. (3.6V p/p) (2) IR pulses (2V p/p) (3) Clock & Data pulses only present when Set is turned on or Off. (3.9V p/p)
87
June 201 LCD TV 1
47LW56000
Soft Touch Key Resistance and Voltages

Key 2 Line KEY 1 Volume (+) Volume (-) Home o e Enter y Key 2 Line KEY 2 CH (Up) CH (Dn) Power Input Pin 5 measured from Gnd 15.9M Ohms 9.8M Ohms 5.7M Ohms 1.19M Ohms KEY 2 CH (Up) CH (Dn) Power Input
J1
Pin 4 measured from Gnd 16.8M Ohms 10.7M Ohms 5 5.4M O s Ohms 1.19M Ohms
KEY 1 Volume (+) Volume (-) Home o e Enter
Pin 4 measured from Gnd 1.67V 1.07V 05 0.54V 0.12V
Pin 5 measured from Gnd 1.56V 0.98V 0.53V 0.12V
1 Diode Mode values taken with all Connectors Removed
88
June 201 LCD TV 1
47LW56000
MOTION REMOTE BOARD SECTION

The first time the Motion Remote has its batteries installed and pointed at the Television, the Motion Remote is synchronized ith s nchroni ed with the TV After that when pointing the TV. that, hen remote at the TV and pressing the Enter key, a pointer appears on screen, then by moving the Motion Remote around, the pointer moves with the movement of the remote. When the pointer is placed over a selectable button, button you can press the center Enter button and Enter active the object. This makes navigation much easier. You can also adjust the volume, change channels and mute the audio with the Motion Remote and it has a convenient Home button for the TV Menu. A wrist band can be attached to the remote to avoid dropping and damaging the remote. The Motion Remote utilizes a specialized receiver on the Television to receive the RF signal and this information is then routed to P1302 and on to the IC101 the BCM IC for pointer positioning and interpretation of the other functions. Pointer (RF transmitter) Power Home Enter Navigation buttons
Volume
Channel
Mute
How to Re-register the Magic Motion Remote Control after Registration Failure. Reset the remote control by pressing and holding both the ENTER and MUTE buttons for 5 seconds. An LED will blink 3 times indicating the remote is ready for registering. Motion Remote Magic Remote AKB72914043
89
June 201 LCD TV 1
47LW56000
Motion Remote Receiver Board Voltage and Diode Check

Motion Remote Board p/n EBR72499601 To Main Board "Motion Remote Receiver Board" To P1302 "Main" Pin Label STBY Run Diode Check 1 3.5V_Normal 0.35V 3.33V 0.53V 2 Gnd Gnd Gnd Gnd 3 M_Remote_RX 0.35V 3.33V OL 4 M_Remote_TX M R t TX 0.35V 0 35V 3.33V 3 33V OL 5 Reset 0.35V 3.33V OL 6 DC_MRemote 0.35V 3.33V 2.41V 7 DD_MRemote 0.35V 3.33V 2.38V 8 Gnd Gnd Gnd Gnd 9 GPI0-O 0V 0V OL 10 GPI0-1 0V 0V OL 11 GPI0-2 0V 0V OL 12 GPI0-3 0V 0V OL
90
June 201 LCD TV 1
47LW56000
INVISIBLE SPEAKER SECTION

The 47LW56000 contains the Invisible Speaker system. The Full Range Speakers point downward, so there is no front viewable speaker grill or air ports.
Back View
Front View
Speaker p/n EAB62088401
91
June 201 LCD TV 1
47LW56000
INTERCONNECT DIAGRAM (11 X 17 FOLDOUT SECTION)
This section shows the 1 1X17 foldout thats available in the Paper and Adobe version of the Training Manual. g For best printing results, use1 X 17 paper. p g , 1 p p
92
June 201 LCD TV 1
47LW56000
47LW5600 INTERCONNECT DIAGRAM

Note: If a particular area is exhibiting a dimmer backlight level than other areas or P3503 "SMPS" to P1601 "MAIN Board" the overall brightness seems dim, be sure to first check the customers Menu Pin Label Pin Label Run Diode setting for Backlights. Raise the percentage and see if the overall brightness returns 5 GND 1 VSYNC 0.1V OL to normal. If not, 6 SCLK 2 SDA N.C. OL 1st: Check the P-DIM level, it should rise with the percentage shown on screen. 7 N.C. 100%, 3.3V. Follow the P-DIM signal all the way to the Inverter. 3 SCL 0.1V OL 2nd: Turn off Local Dimming in the Customers Menu. If the brightness returns to 8 REVERSE 4 SIN Gnd OL normal, examine the signals required for Local Dimming. No Stand-By voltages (SIN, V-SYNC and SCLK).
100uF/100V
P201 "SMPS Board" To P502 "MAIN Board"
P1302 "MAIN Board" To "Motion Remote"

Pin 1 2 3 4 5 6 7 8 9 10 11 12 Label 3.5V_Normal Gnd M_Remote_RX M_Remote_TX Reset DC_MRemote DD_MRemote Gnd GPI0-O GPI0-1 GPI0-2 GPI0-3 STBY 0.35V Gnd 0.35V 0.35V 0.35V 0.35V 0.35V Gnd 0V 0V 0V 0V Run 3.33V Gnd 3.33V 3.33V 3.33V 3.33V 3.33V Gnd 0V 0V 0V 0V Diode Check 0.53V Gnd OL OL 2.41V 2.38V Gnd Gnd OL OL OL OL
P502 "MAIN Board" To P201 "SMPS Board" Pin 1 2-4 5-8 9-12 13-15 16 17 18 19 20 21
BCM IC101
Run Gnd 3.25V 3.25V 0V
Diode Gnd OL OL 1.91V
PWR-ON: Starts 12V, 24V and 36V LED Power. No Backlights. DRV-ON: Starts Backlights LED Power goes to 65 then down to 50V.
PWM Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition). Output from the Video Processor. Range 0.2V to 3.3V.
(1)
To the Panel
You can also test each of the 12 blocks functionality by grounding the return path signal through a 220. See Forcing on a Block of LEDs on the right. P202 White Plug "SMPS Board" To "Panel LEDs"
100uF/100V
P203
50V
P202
VC_3C VC_1D VC_1C VC_4D VC_4C VC_2A VC_1B VC_1A VC_4B VC_4A VC_3D
L601
Diode OL OL OL OL OL OL OL OL OL OL OL OL
SCLK Pin 6 P832 3.54V p/p MOSI Pin 4 P832 3.57V p/p Local Dimming Off MOSI Pin 4 P832 3.57V p/p Local Dimming On
- + - + C257 C256
Pin 1 2 3 4 5 6 7 8 9 10 11 12
Label LED+ n/c VC-3A VC-3B VC-3C VC-3D VC-4A VC-4B VC-4C VC-4D n/c LED+
TP C256+ n/c EL70 EL71 EL72 EL73 EL74 EL75 EL76 EL77 n/c C256+
Run 50V n/c
BD101
D253
VC_2C
VC_3B
*1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V

n/c 50V
Q251 + Q602
VC_3A VC_2D
Pin Label ERROR 24 n/c 23 (1) 22 PWM 21 12V 20 n/c 19 12V 18 DRV-ON 17 12V 16 V_Sync 13-15 Gnd 9-12 3.5V 5-8 Gnd 2-4 24V 1 PWR-ON
STBY Run Diode Check n/c n/c 2.03V n/c n/c OL 0V 0.2V~3.3V OL 0V 11.92V 0.48V n/c n/c OL 0V 11.92V 0.48V 0V 3.26V OL 0V 11.92V 0.48V 0V 0V OL Gnd Gnd Gnd 3.55V 3.53V 2.63V Gnd Gnd Gnd 0V 24.19V 1.09V 0V 3.4V 1.15V
P502
C
Q601 IC102 D603
SMPS BOARD p/n: EAY62169801
VC_2B
P701
n/c
Q504
B C E
Q502 Q501 3 2 IC502 1

3 1 2
E C B
E B
RL_ON Drivers
P3503
P101 N/C
Diode OL OL Gnd 1.16V Gnd OL 2.32V 1.62V 2.32V OL 2.07V 2.32V OL OL
D251 D252 D255 D256
IC503 Q1701
C E B
P832
L1704 L1703
INV_CTL Driver
Audio Mute
To Spk
L1708
IC1702 Audio Amp

P203 Black Plug "SMPS Board" To "Panel LEDs"
T101
RL101
D261
P201
Chassis Ground
12.09V Each Pin
P1702
L1707
0.9V FET Switch 3.3V_ 5V_Normal L505 Q503 Normal IC507 IC501 IC505 +0.9V_CORE Q508 IC506 0.9V FET Switch IC5402 5V_USB +3.3V_FRC NAND FLASH IC102 USB2 EDID IC1203 IC103
Q102
G D D B S G B
P1502
IC5301
IC5403 +1.5V_FRC IC5202 IC401 DDR IC402 DDR IC508
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13
Label LED+ n/c VC-1A VC-1B VC-1C VC-1D n/c VC-2A VC-2B VC-2C VC-2D n/c LED+
TP C256+ n/a EL62 EL63 EL64 EL65 n/a EL66 EL67 EL68 EL69 n/a C256+
Run
50V
Diode OL OL OL OL OL OL OL OL OL OL OL OL OL
Any drive signal VC1 through VC4 A~D V-SYNC Pin 1 P832 3.5V p/p
DDR
n/c
F100
5A / 250V
Q102
Hot Ground
T501
IC503
*1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V

n/c
F501 F101
3.15A / 250V
Q101
IC502
B E C
IC5201 FRC
X5201
NVRAM
22 23 24
47uF/450V
47uF/450V
47uF/450V
IC1204
USB1 EDID
Q710
G B S D
1.6A / 250V
SK100 AC In
W/Washer Different Size
Video Processor
Q101
Indicates Hot Ground
Stby: 399V Run: 398.5V
Stby: 397V Run: 396.5V
IC501
C
Q505
B E
Q506
D
G S
*1.39V~13.74V *1.39V~13.74V *1.39V~13.74V *1.39V~13.74V

n/c
50V
Q507
IC5401 +1.26V_FRC IC504

X601
+1.5V_DDR +2.5V_BCM35230
Earphone Amp IC804

B E C
IC701
Q801
A1 A2
P3503 "SMPS Board" To P832 "MAIN Board" Pin 1 2 3 4 5 6 7 8 Diode OL OL OL Gnd OL 1.73V 1.71V OL
D713
P1501
IC601 MICRO IC602
C E
HDMI Selector
D711
C
A1 A2

SMPS TEST 1
Top pins on connector are odd numbers.
PANEL TEST To run the T-CON Panel Test, remove the LVDS cables. Jump 12V to the 12V fuse. Jump VCC 3.3V to pin 44 on CN1. White, Red, Blue, Green and Black patterns show on screen.
(11.76V) (11.76V)
LVDS
To Main
U5
LVDS
12V
5) Gnd 6) Gnd 7) Gnd 8) Gnd
4) 3.31V 3) 3.3V 2) 2.95V 1) 3.3V
P201
23 24
SMPS TEST 2 Top pins on P201

connector are odd numbers.
23 24
12V 21 22 12V 19 20 12V 17 18 STBY 3.5V 9,10,11,12 13 14 11 12 9 10 7 8 A 5 6 1 2 24V 15 16
12V 21 22 12V 19 20 12V 17 18 STBY 3.5V 9,10,11,12 13 14 11 12 9 10 7 8 A 5 6 1 2 24V 24V 3 4 24V PWR ON 15 16 DRV-ON B
SMPS TEST 1: Force Power Supply On. Disconnect P502 on Main board. (A) Jump pins 9, 10, 11 or 12 (3.5V) to pin 1. Test Voltage Outputs 12V, 24V to Main and 36V to the Inverter Section of the SMPS. Remove AC power. Leave the jumper in place. No Backlights. 50V to Backlights reads 36V. SMPS TEST 2: Force the Backlights On. (B) Jump pins 9, 10, 11 or 12 (3.5V) to pin 18 (DRV-ON). Apply AC power, the Backlights should turn on. Note, the LED B+ will now jump to 65V then back down to 50V. Note; If there is a problem with a load from the panel backlights, you can remove AC and Disconnect P202 or P203. When AC is reapplied, the Backlight LEDs should turn on for about 4 seconds and then shut off.
p/n: EBR72948402 AUSYLHR p/n: EBR73145901 AUSYLJR X602 Q1001 Q901 B SW1 Wireless Dongle Switch p/n: EBR72948404 AUSYLUR C Q902 E SW1 Grayed out RS232 Microprocessor 18. IF p 17. IF n Reset 18 components are 16. IF AGC 15. Reset P901 on the back 14. 3.3V
D
C
Q904 B Q906 E
C B C B E
P601 N/C
MAIN BOARD
Q1002 D708
A1 A2
G S
12V
(8.7V) HVDD
IC803
Gnd
CN2
(3.35V)
Gn d
Gnd
Gnd
Gnd
(11.76V)
CN1
F1 3A/125V Panel Test TP 44
L1 D6
L3
U5 FL2
L2
(3.31V)
Gn d
D7 US1
VCC 3.3V
UC1
-2.8V Pin 10 Pin 11 Pin 12
Note: VGHEVEN and VGHODD swap once a second Pin 13
VDD 16.48V
Pin 18 (24.9V) 1
2 3
Pin 15
D3 D2
(29.1V)
US1 Q12 Q11 2

2
VST -5V
U3
VGHEVEN 29V
U6
P-VDD 16.37V Pins 7-8
1) 28.4V 2) 29V 3) 29.1V
3) Gnd 2.1V 2) 1.6V 1) 0.6V
3 2 1
-2.8V
D1
Warning: T-CON Board under shield. Be sure to reinsert screws before operating set with shield removed.
TU2101 TUNER
IC801
D810
13. 1.26V 12. GND 11. CVBS 10. NC 9. SIF 8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
C B E C
Q2105
IC2103
3 2 1 2
C
A1 A2
Q2104
D710
V 12
P1302
+1.26V_TU
D707 1
A1 A2
PC Data
IC802 PC EDID
A1 A2
VGHR 29V VGHF -5V VGHODD -4.9V

C106
FL1
CN4
VGL_I -5V
C101 C102
CN5
VDD 16.47V
C105
P901 Connector "MAIN Board" To "IR Board" Pin Label STBY Run Diode Pin Label
STBY Run Gnd 0V Gnd 0V
Diode Gnd OL OL Gnd OL OL
Pin Label 13 14 15 Gnd S/T_SCL S/T_SDA
STBY Run Gnd Gnd 3.55V 3.49V 3.55V 3.49V
Diode Gnd OL OL
24V 3 4 24V PWR ON
1 2 3
SCL SDA Gnd KEY 1 KEY 2
3.55V 3.49V 3.55V 3.49V Gnd Gnd 3.33V 3.3V 3.33V 3.3V
OL OL Gnd OL OL OL
7 8 9 10 12
Gnd LED_B IR Gnd LED_R
For DC voltages for Main board components see Page 2 of the Interconnect diagram.
VST VGLI VGHEVEN VGHODD VGHF VGHR
29V -5V -5V 28V
-5V -5V 3.3V 16.48V
TO TFT MODULE
29V -5V -5V 28V
-5V -5V 3.3V 16.48V
4 5 6
1.48V 1.47V Gnd Gnd 0V 0V 3.33V 0V
11 +3.3V_Normal
3.5V_ST 3.55V 3.49V
p/n: EBR72671301
p/n: EBR72499601
Front IR/Key
Ft. IR/Intelligent Sensor And Soft Touch Key Board
Other Voltages from U6 to the Panel with no silk screen labels: U6 pin 11: (13V) to CN4 pin 3, CN5 pin 58 U6 pin 12: (12.1V) to CN4 pin 4, CN5 pin 57 U6 pin 13: (10.25V) to CN4 pin 5, CN5 pin 56 U6 pin 14: (6.17V) to CN4 pin 8, CN5 pin 53 U6 pin 15: (4.3V) to CN4 pin 9, CN5 pin 52 U6 pin 18: (3.3V) to CN4 pin 10, CN5 pin 51 U6 pin 19: (2.65V) to CN4 pin 11, CN5 pin 50 U6 pin 20: (16.37V) to CN4 pin 40,41, CN5 pin 20, 21
Panel p/n: EAJ61768201 AUSYLHR, AUSYLJR, AUSYLUR
Panel p/n: EAJ61928101 AUSYLUR
Motion Remote
47LW5600 MAIN (FRONT SIDE) SIMICONDUCTORS IC103 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC501 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] IC504 Pin [1] [2] [3] [4] [5] [6] [7] [8] n/c 0V 3.34V 0V 3.22V 3.22V 0V (Gnd) 3.34V +0.9V_CORE DC to DC 3.17V 0.59V 0.44V 11.95V 0V 5.33V 4.6V 5.81V 0.95V 1.36V +2.5V BCM Regulator n/c 4.92V (En) 3.47V (In) 3.49V (Ctl) n/c 2.57V (Out) 0.6V 0V (Gnd) IC506 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC507 Pin [1] [2] [3] [4] [5] [6] [7] [8] NVRAM for USB IC505 Pin [1] [2] [3] [4] [5] [6] [7] [8] (+3.3V_NORMAL) Regulator 0V (Gnd) 11.96V (In) 0V (Gnd) 0.8V 0.79V 3.47V (PWR On/Off2_2) 3.35V (Out) 3.35V (Out) Switched 5V for USB 2 0V (Gnd) 11.98V (In) 0V (Gnd) 0.79V 3.48V 3.48V (PWR On/Off2_1) 4.96V (Out) 4.96V (Out) (+5V_NORMAL) Regulator 0V (Gnd) 11.98V (In) 0V (Gnd) 0.79V 3.48V 3.48V (PWR On/Off2_1) 4.96V (Out) 4.96V (Out) IC508 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC801 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] (+1.5V_DDR) Regulator 3.46V n/c 3.46V (In) 3.49V (PWR On/Off1) 0V (Gnd) 3.31V 0.79V 1.5V (Out) RGB Data Buffer 1.81V 1.81V 3.72V 1.8V 1.8V n/c (4.44V) 0V (Gnd) n/c (4.43V) n/c (1.79V) n/c (1.79V) 3.72V 1.81V 1.81V 5V (Vcc In) IC803 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC802 Pin [1] [2] [3] [4] [5] [6] [7] [8] EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.73V 4.73V 4.73V 4.73V (Vcc In) RS232 Routing 3.5V 5.64V 0V 0V (-5.56V) (-5.59V) n/c (5.64V) n/c (0V) n/c (3.49V) n/c (0V) n/c (3.34V) 3.48V 0V (-5.59V) 0V (Gnd) 3.5V (Vcc In) IC1203 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC1204 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC2103 Pin [1] [2] [3] EDID Data PC 0V (Gnd) 4.96V (Vcc In) 4.96V (Vcc In) 3.34V (USB Ctl2) 3.17V 4.96V (Out) 4.96V (Out) n/c (0V) EDID Data PC 0V (Gnd) 4.96V (Vcc In) 4.96V (Vcc In) 3.34V (USB Ctl1) 3.17V 4.96V (Out) 4.96V (Out) n/c (0V) (+1.26V_TU) Regulator 0V (Gnd) 1.27V (Out) 3.33V (In) IC5401 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC5402 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q501 Pin B C E Q502 (+1.26V_FRC) Regulator 0V (Gnd) 11.85V (Vcc In) 0V (Gnd) 0.8V (FB) 0.7V 3.29V (Enable) 1.29V (Out) 1.29V (Out) (+3.3V_FRC) Regulator Under Shield Under Shield Under Shield Under Shield 0.8V 3.45 (PWR On/Off2_2) 3.3V 3.3V RL_ON (PWR_On) 1st Driver 0.64V 0V Gnd Q503 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q508 Pin [1] [2] [3] [4] [5] [6] [7] [8] 0.9V FET Switch 0.95V 0.95V 0.95V 1.36V 11.96V 11.96V 11.96V 11.96V 0.9V FET Switch 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.6V 0.95V 0.95V 0.95V 0.95V Wireless Vcc Pin Driver B 0.02V C 24.5V E Gnd On when wireless dongle connected Wireless Vcc Pin Switch S 24.5V G 24 5V 24.5V D 0V On when wireless dongle connected Q1002 Q1001
Q901
IR Buffer Pin 2nd B 0.02V C 3.48V E Gnd IR Buffer Pin 1st B 0.57V C 0.02V E Gnd
Q902
PWR_ON Pin Switch [1] 3.5V (In) [2] 0.67V [3] 2.62V (Out)
47LW5600 MAIN (BACK SIDE) SIMICONDUCTORS IC502 Power Det Gen Pin (For +12V) [1] 0V (Gnd) [2] 3.8V (In) [3] 3.73V (Out) Power Det Gen Pin (For +24V) [1] 0V (Gnd) [2] 3.7V (In) [3] 3.73V (Out) Q506 IC601 Pin [1] [2] [3] [4] [5] [6] [7] [8] EEPROM Micro 0V (Gnd) 0V (Gnd) 3.49V 0V (Gnd) 3.49V 3.49V 0V (Gnd) 3.50V (Vcc In) IC5202 Pin [1] [2] [3] [4] [5] [6] [7] [8] SPI FLASH 0.43V 3.29V 3.29V 0V (Gnd) ?? ?? 3.29V 3.29V (3.3V_FRC in) Q101 Pin [B] [G] [S] [D] Q102 Pin [B] [G] [S] [D] Q504 RGB_DDC_SDA FET Buffer 0V (Gnd) 3.3V 4.74V 3.34V RGB_DDC_SCL FET Buffer 0V (Gnd) 3.3V 4.74V 3.34V Q710 Pin [B] [G] [S] [D] Q801 Pin B 0V C 3.35V E Gnd Q904 INV_CTL (Drv_On) INV CTL (Drv On) Pin Driver B 0V (INV ON) En C 3.28V (Out) E Gnd Q906 Q505 PANEL_VCC Pin Control 1st Driver B 0V C 0.68V E Gnd Pin B C E Pin B C E 3.47V 3.51V 3.47V 3.49V Q2106 Earphone Mute CEC Remote HDMI CEC Q2104 Tuner SIF Pin (Sound) Buffer B 0.23V C 0V (Gnd) E 0.93V Tuner Video Pin (Analog) Buffer B 3.67V C 0V (Gnd) E 4.35V 5V Pull-Up to Pin DDC_SCL/SDA_1 A1 4.96V C 5V A2 0V 5V Pull-Up to Pin DDC_SCL/SDA_3 A1 4.96V C 5V A2 0V D710 Pin A1 C A2 D711 Pin A1 C A2 D713 5V Pull-Up to DDC_SCL/SDA_2 4.96V 5V 0V 5V Pull-Up to DDC_SCL/SDA_4 4.96V 5V 0V
IC503
PANEL_VCC Pin Control 2nd Driver B 0.67V C 0V E Gnd PANEL_VCC Pin Switch S 11.97V (In) G 1.8V (Enable) D 11.94V (Out)
D707 IR Wireless Pass 2nd Driver 0.02V 3.48V Gnd D708 IR Wireless Pass 1st Driver 0.57V 0V Gnd
Bias for Q710 Pin HDMI CEC A1 0V C 3.45V A2 3.5V 5V Routing to Pin IC802 RGB EDID A1 4.73V C 5.01V A2 0.07V
Q507
D810
47LW56000 Conclusion Page
Direct View LCD
This Thi concludes the l d th 47LW56000 training session. session

LG 47lw5600 - Training Manual

Uploaded by

Copyright:

Available Formats

LG 47lw5600 - Training Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG 47lw5600 - Training Manual

Uploaded by

Copyright:

Available Formats

What are the main sections covered in the training?

What are the main sections covered in the training?

What are the steps involved in disassembling the LCD?

What are the steps involved in disassembling the LCD?

1080P Direct View LCD Training

Published June 1st, 201 1

Overview of Topics to be Discussed

47LW56000 LCD Direct View Display

June 201 LCD TV 1

Preliminary Matters (The Fine Print)

IMPORTANT SAFETY NOTICE

June 201 LCD TV 1

(Electrostatic Static Discharge)

June 201 LCD TV 1

June 201 LCD TV 1

LCD Direct View Overview

Checking Points to be Considered

June 201 LCD TV 1

Basic Troubleshooting Steps

June 201 LCD TV 1

47LW56000 PRODUCT INFORMATION SECTION

Wireless Media Box

Wired Remote to control the Media Box TV A/V Inputs

June 201 LCD TV 1

Wireless Network Adaptor (AN-WF100)

Side A/V Inputs

Wireless Adaptor Dongle

Cat 5 Cable with RJ 45 Connectors on each side

June 201 LCD TV 1

June 201 LCD TV 1

Logo Familiarization Page 1 of 3

June 201 LCD TV 1

Logo Familiarization Page 2 of 3

June 201 LCD TV 1

Logo Familiarization Page 3 of 3

June 201 LCD TV 1

47LW56000 Remote Control

p/n AKB73295502 BOTTOM PORTION

June 201 LCD TV 1

TV Rear Input / Output Jacks

Side In/Out Sid I /O t

June 201 LCD TV 1

Software Updates (New and Changed Functions)

June 201 LCD TV 1

Generic Plasma USB Automatic Software Download Instructions

Jump Drive Directory

Software File LG_DTV Sub-Directory

Software Files are now available from LGTechassist.com

June 201 LCD TV 1

Manual Software Download:

Press the FAV key 7 times

Location of files found On the Jump Drive

June 201 LCD TV 1

Product and Service Info. Menu

June 201 LCD TV 1

Accessing the Host Diagnostic Screen (Page 1 of 2)

See next page for more details.

June 201 LCD TV 1

42LW5600 Understanding the Host Diagnostic Screen (Page 2 of 2)