INTERNAL (REF) TWIN DISC

SPLINE DATA ENGR. STD. S435 2 PTO ADAPTER MOUNTING FACE BILL OF MATERIAL
ROOT FLAT PRESSURE ANGLE 30° ITEM NO. QTY. PART NO. DESCRIPTION
NO. OF TEETH 17 PITCH 12/24
1 1 A2669FV RING, SNAP
PITCH DIA 1.4167 FORM DIA. 1.4833 2 1 A2916KD RING, O
(REF) MIN.
5
3 1 M1904L RING, PISTON
4 1 M1945T PLUG
MAJOR DIAMETER MAX. 1.500
4
5 2 MA1035B PIN, DOWEL
MIN. EFF. .1327 6 1 MA1038D PLUG, STRAIGHT THREADED
CIRCULAR SPACE
WIDTH 7 1 MA1038F PLUG, STRAIGHT THREADED
MAX. ACT. .1345
8 2 MA1062R SCREW, SOCKET HEAD
MEASUREMENT BETWEEN MIN. REF. 1.2052 9 4 MA1062S SCREW, SOCKET HEAD
.144 DIA. PINS WITH REFERENCE ONLY: 6
MAX. ACT. 1.2078 10 1 1015532 CARRIER
NONE TO FLAT

SPLINE DATA IN INCHES

DRAIN HOLE LOCATION. A 11
12
1
1
1017834A
1017836A
ADAPTER, DRIVE
ADAPTER, SPLINED
SECTION B-B 13 INCLUDE ONE (1) COPY OF DRAWING 1029792
SCALE 1 : 4 9

B 2
78.00
7

10
25.00

3
12

8 4 3

16.00

17.74
127.06±0.03

SEE SPLINE
DATA CHART

B 11 2 1
4X M16X2.0 - 6H TAP THRU
2
APPLICABLE MODELS:
MG-6848SC PER 1022144A ASSEMBLY
MG-6690SC PER 1022143A ASSEMBLY
SECTION A-A 161.9 REF. HC
SAE J744 No. 127-4
MG-6650SC PER 1022142A ASSEMBLY
MG-5321DC PER 1015339B ASSEMBLY
MGX-6848SC PER 1020675A ASSEMBLY
181.0 REF. HC
A MGX-6690SC PER 1020674A ASSEMBLY
MGX-6650SC PER 1002046A ASSEMBLY
SAE J744 No. 127-2 MGX-5321DC PER 1022203B ASSEMBLY
FACTORY INSTALLATION INSTRUCTIONS: ASSEMBLY INSTRUCTIONS:
A. PRESS THE (2) DOWEL PINS IN THE SHAFT UNTIL THE PINS PROTRUDE 9.0mm FROM END OF SHAFT.
B. ASSEMBLE THE PISTON RING INTO THE GROOVE OF THE PUMP DRIVE ADAPTER AND INSTALL THE PUMP DRIVE ADAPTER OVER THE DOWEL PINS IN THE SHAFT. - FOR MG-6848SC & MGX-6848SC SEE S570EP SECTION I. FOR INSTRUCTIONS.
FASTEN THE ADAPTER TO THE SHAFT WITH (2) CAPSCREWS AND TORQUE PER S574 (OR SERVICE MANUAL) VALUES. REFERENCE S570EP FOR ADDITIONAL STANDARDS AND INSTRUCTIONS THAT MAY APPLY.
C. ASSEMBLE THE NEW O-RING AND THE 1015532 AUXILIARY PUMP CARRIER ONTO THE MANIFOLD SO THAT THE SLOT
IN THE CARRIER BORE ALIGNS WITH THE DRAIN HOLE IN THE MANIFOLD (SEE SECTION B-B). - FOR MG-6690SC & MGX-6690SC SEE S570EQ SECTION I. FOR INSTRUCTIONS.
MAKE SURE THAT THE PLUG IS NOT INSTALLED IN DRAIN HOLE AND THEN FASTEN THE 1015532 CARRIER USING THE (4) CAPSCREWS AND REFERENCE S570EQ FOR ADDITIONAL STANDARDS AND INSTRUCTIONS THAT MAY APPLY.
TORQUE PER S574 (OR SERVICE MANUAL) VALUES
D. START M1945T CUP PLUG INTO CARRIER BORE. APPLY A THIN BEAD OF ANAEROBIC SEALANT M2828 TO THE PLUG O.D. PER S774 AND - FOR MG-6650SC & MGX-6650SC SEE S570ER SECTION I. FOR INSTRUCTIONS.
INSTALLTHE PLUG FLUSH WITH THE REAR SURFACE OF THE CARRIER. REFERENCE S570ER FOR ADDITIONAL STANDARDS AND INSTRUCTIONS THAT MAY APPLY.
E. ASSEMBLE SNAP RING A2669FV INTO SPLINED ADAPTER 1017836A, AND SHIP LOOSE IN A BAG ATTACHED TO THE TRANSMISSION.
- FOR MG-5321DC & MGX-5321DC SEE S570FA SECTION I. FOR INSTRUCTIONS.
REFERENCE S570FA FOR ADDITIONAL STANDARDS AND INSTRUCTIONS THAT MAY APPLY.
FIELD INSTALLATION INSTRUCTIONS:
A F. FOLLOW STEPS 'A-D' NOTED ABOVE, IF INSTALLING THE ENTIRE AUXILIARY PUMP DRIVE ADAPTER IN THE FIELD AND THEN CONTINUE WITH STEP 'H' BELOW. - ALL FASTENERS, FITTINGS AND PLUGS TO BE TORQUED PER S574.
1
OTHERWISE PROCEED TO STEP 'G' BELOW. A ECNWF-75103 07/21/2015
G. REMOVE M1945T PLUG. SAE J744 NO. 127-2/4 FLANGE AND SAE J744 NO 38-4 PUMP DRIVE ADAPTER REV CHANGE NO. DATE
H. INSTALL THE 1017836A ADAPTER WITH THE A2669FV SNAP RING
J. ASSEMBLE THE PUMP (WITH A SUITABLE SEALING MECHANISM) ONTO THE AUXILIARY PUMP DRIVE ADAPTER USING CAPSCREWS MATERIAL: DATE:
FIRST USE ASSEMBLY:1020675A 9.88kg
TORQUED PER S574 (OR SERVICE MANUAL) VALUES. WEIGHT:
THIRD ANGLE 04/04/2015
FIRST USE MODEL: MGX-6848SC PROJECTION
2
WR : kg-m
2 SCALE:
(PUMP, MOUNTING SCREWS AND ASSOCIATED SEALING MECHANISM ARE NOT TWIN DISC SUPPLIED). SIMILAR TO:
HEAT TREAT: 1:2 RACINE, WI 53403 - USA

APPLICATION NOTES: METRIC UNLESS OTHERWISE SPECIFIED

MACHINED DIMENSIONS
X.
X.X
0.75
0.25
DESCRIPTION:
DRAWN BY:
PM
CHECKED BY: 1029792
- MAX. APPROVED INPUT TORQUE TO SAE J744 38-4 SIZE PUMP ADAPTER: 1187 N-m.
NOTICE! THIS PRINT CONTAINS PROPIETARY INFORMATION AND IS
NOT TO BE USED IN ANY MANNER DETRIMENTAL TO THE INTEREST OF
X.XX 0.13
YU
TWIN DISC, INCORPORATED
ALL ANGULAR TOLERANCES ±1°
GROUP, PTO APPROVED BY: DWG SHEET: REV:
- CONSULT SALES DEPTARTMENT APPLICATION ENGINEERS FOR OTHER LIMITING CONDITIONS. THIS NOTICE IS NOT INTENDED TO NULLIFY OR LIMIT RIGHTS
GEOMETRIC TOLERANCING
PER ASME Y14.5M 1994 SAE J744 LIVE 127-2/4, 38-4 SIZE: A2 1 OF 1 A
GRANTED TO THE U.S. GOVERNMENT OR OTHERS BY CONTRACT. KSK
D C B A