Scribd
Upload
240 views3 pages

Bandlab Rec

Uploaded by

aviart2010
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
240 views3 pages

Bandlab Rec

Uploaded by

aviart2010
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

To refine, clear, and remove background noise from your vocal recordings using BandLab,

follow these steps. BandLab offers some basic tools for noise reduction and vocal
processing, but keep in mind it’s not as advanced as dedicated DAWs for in-depth noise
removal. However, it’s still a very good option for quick edits. Here's how you can clean up
your vocals:

1. Upload Your Vocal Track

• Open BandLab in your browser or through the app.


• Create a new project or open an existing one.
• Upload your vocal recording by dragging it into the track view or using the Upload
button.

2. Noise Removal Using the Equalizer (EQ)

BandLab doesn’t have an automatic noise reduction tool, but you can use EQ to reduce
unwanted background frequencies, especially if you have a consistent noise like hum or
hiss.

• Select your vocal track.


• In the track settings, click on FX to open the effects panel.
• Apply an EQ (equalizer) to the track.
o Use a low-cut filter (high-pass filter) to remove low-end rumble or hum
below 100Hz (adjust depending on your recording).
o If there’s hiss or harshness, try cutting some of the higher frequencies
(around 3kHz to 8kHz).
o Be gentle with EQ cuts—too much can make your vocals sound thin or
unnatural.

3. Use Noise Gate for Background Noise Reduction

A noise gate can help eliminate constant background noise during silent parts of your
recording. You can find a simple noise gate effect in BandLab.

• Click on the FX button again for your track.


• Look for a Noise Gate effect (it might be under a "Dynamics" section).
• Set the threshold so that the gate only opens when your vocal signal is above a
certain level, effectively muting the noise during quieter sections.
Tip: Be careful with the threshold—if it’s too aggressive, it can chop off parts of your vocal
performance. Start with a mild threshold and adjust as needed.

4. Use Compression for Consistent Volume

Compression can help even out your vocal performance, especially if you have quiet and
loud sections. While this isn’t strictly for noise removal, it can help make your vocals
sound more polished and controlled.

• Add a Compressor effect from the FX menu.


• Set a low Ratio (2:1 or 3:1) and adjust the Threshold so that the compressor kicks in
only during louder parts of your performance.
• Adjust the Attack and Release settings for smooth compression.

5. De-essing for Sibilance

If your recording has harsh “s” or “sh” sounds (sibilance), you can reduce them using a de-
esser plugin (BandLab has this built in, or you can simulate it with EQ).

• Add the De-Esser effect in the FX section.


• Adjust the Threshold to target the sibilant frequencies (typically around 5kHz–
8kHz).
• This will smooth out harsh high frequencies and make the vocal sound cleaner.

6. Manual Cleanup

For specific noises that can’t be handled by effects, you can zoom into your track and
manually adjust or delete problematic areas.

• In the editor view, zoom in and look for any spikes or clicks in the waveform that
could be caused by mouth noises, pops, or random background sounds.
• You can delete or reduce these areas manually by selecting and cutting them out,
or by using the volume envelope to lower the volume during those sections.

7. Final Adjustments and Mixing

• After reducing the noise and refining the vocal, you can adjust the overall mix. Add
reverb, delay, or other effects as needed, but make sure the vocal still sounds
natural.
• Balance the levels of the vocals with any backing music or instruments in the mix.

8. Export and Listen on Different Devices

After you've cleaned up your vocals, export the project to see how it sounds on different
devices (headphones, speakers, etc.). Sometimes, background noise or EQ issues can
become more apparent on different playback systems.

Extra Tips:

• Use High-Quality Headphones: When editing, using quality headphones can help
you catch subtle noises and artifacts in your recordings.
• Record in a Controlled Environment: Even with all the digital tools, the best way to
reduce background noise is to record in a sound-treated space (e.g., use a pop
filter, foam panels, or a portable isolation booth).
• Monitor Gain Levels: Make sure your vocal recordings are not clipping or overly
quiet, as this can make noise reduction less effective.

You might also like