Process Eye Professional

and

EasyView

From Version 5.20 onwards

Process Eye Professional V5 User Manual

SP104008.100 August 2005
As part of our continuous product improvement policy, we are always pleased to receive your comments and
suggestions about how we should develop our product range. We believe that the manual is an important
part of the product and would welcome your feedback, particularly relating to any omissions or inaccuracies
you may discover.

You can send your comments to:-

MKS Instruments, Spectra Products

Cowley Way
Crewe
Cheshire
CW1 6AG
U.K.

+44 (0) 1270 250150 Tel.

+44 (0) 1270 251939 Fax.

Email – [email protected]

Windows is a trademark of the Microsoft Corporation. All other brand or product names are trademarks or
registered trademarks of their respective companies.

Process Eye Professional V5 –SP104008.100 August 2005 2

Licence Terms and Conditions

MKS INSTRUMENTS
ELECTRONIC END USER LICENSE AGREEMENT
FOR MKS RGA APPLICATION SOFTWARE

This MKS Instruments ("MKS") End User License Agreement accompanies the 'MKS(r) RGA Software' and
'MKS(r) RGA Demonstration Software' products and related explanatory materials ("Software"). The term
"Software" also shall include any upgrades, modified versions or updates of the Software licensed to you by
MKS. Please read this Agreement carefully. At the end, you will be asked to accept this agreement and
continue to install or, if you do not wish to accept this Agreement, to decline this agreement, in which case
you will not be able to use the Software.

The terms of this license are not affected by any of the following
- whether you purchased the software in association with MKS hardware
- whether you obtained the software at no cost for an 'evaluation'
- whether the software is labeled 'Demonstration'
because both the 'RGA Software' and the 'RGA Demonstration Software' are fully featured implementations
of the software product. For this reason the same license restrictions apply whether the software was
obtained for demonstration or commercial purposes. By the same token, it makes no difference to the
license terms whether you have paid for the software as part of a commercial arrangement or you obtained
it for no charge as an evaluation copy.

Upon your acceptance of this Agreement, MKS grants to you a nonexclusive license to use the Software,
provided that you agree to the following:

1. Use of the Software.

- You may only install the software if it was supplied to you, or a business colleague in the same company as
yourself and at your business location, by MKS or one of MKS' agents or distributors. It is your responsibility
to know the identity of the individual or group of individuals at your business location who was / were the
original licensed recipient direct from MKS or its agent or distributor.

- You may install the Software on a hard disk or other storage device; install and use the Software on a file
server for use on a network for the purposes of (i) permanent installation onto hard disks or other storage
devices or (ii) use of the Software over such network; and make backup copies of the Software.

- You may make and share unlimited copies of the Software for others in your own company to use at the
same business location.

- Ownership of MKS RGA hardware does not, of itself, confer a right to install the software. If you did not
obtain said hardware directly from MKS or one of its agents or distributors, you must contact MKS and make
separate arrangements to obtain a licensed copy of the software direct from MKS or one of its agents or
distributors.

2. Copyright and Trademark Rights.

- The Software is owned by MKS and its suppliers, and its structure, organization and code are the valuable
trade secrets of MKS and its suppliers. The Software also is protected by United States Copyright Law and
International Treaty provisions. You may use trademarks only insofar as required to comply with Section 1 of
this Agreement, in accordance with accepted trademark practice, including identification of trademark
owner's name. Such use of any trademark does not give you any rights of ownership in that trademark.
Except as stated above, this Agreement does not grant you any intellectual property rights in the Software.

3. Restrictions.

- You agree not to modify, adapt, translate, reverse engineer, decompile, disassemble or otherwise attempt
to discover the source code of any compiled Software. You agree neither to redistribute the complete

Process Eye Professional V5 –SP104008.100 August 2005 3

software nor any of the examples or documentation to any third party or to a different business location
within your own organization.
- You agree not to pass on the software, in part or as a whole, to any third party or to any person or persons
in your own company organization but not at your business location. This restriction applies equally whether
or not your own organization obtained the software at no cost.

4. No Warranty.

- The Software is being delivered to you AS IS and MKS makes no warranty as to its use or performance.
MKS AND ITS SUPPLIERS DO NOT AND CANNOT WARRANT THE PERFORMANCE OR RESULTS YOU MAY
OBTAIN BY USING THE SOFTWARE OR DOCUMENTATION. MKS AND ITS SUPPLIERS MAKE NO
WARRANTIES, EXPRESS OR IMPLIED, AS TO NONINFRINGEMENT OF THIRD PARTY RIGHTS,
MERCHANTABILITY, OR FITNESS FOR ANY PARTICULAR PURPOSE. IN NO EVENT WILL MKS OR ITS
SUPPLIERS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES,
INCLUDING ANY LOST PROFITS OR LOST SAVINGS, EVEN IF AN MKS REPRESENTATIVE HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY THIRD PARTY. Some
states or jurisdictions do not allow the exclusion or limitation of incidental, consequential or special damages,
or the exclusion of implied warranties or limitations on how long an implied warranty may last, so the above
limitations may not apply to you.

5. Governing Law and General Provisions.

- This Agreement will be governed by the laws of the State of Massachusetts, U.S.A., excluding the
application of its conflicts of law rules. This Agreement will not be governed by the United Nations
Convention on Contracts for the International Sale of Goods, the application of which is expressly excluded.
If any part of this Agreement is found void and unenforceable, it will not affect the validity of the balance of
the Agreement, which shall remain valid and enforceable according to its terms. You agree that the
Software will not be shipped, transferred or exported into any country or used in any manner prohibited by
the United States Export Administration Act or any other export laws, restrictions or regulations. This
Agreement shall automatically terminate upon failure by you to comply with its terms. This Agreement may
only be modified in writing signed by an authorized officer of MKS.

6. Notice to Government End Users.

- The Software and Documentation are "Commercial Items," as that term is defined at 48 C.F.R. §2.101,
consisting of "Commercial Computer Software" and "Commercial Computer Software Documentation," as
such terms are used in 48 C.F.R. §12.212 or 48 C.F.R. §227.7202, as applicable. Consistent with 48 C.F.R.
§12.212 or 48 C.F.R. §§227.7202-1 through 227.7202-4, as applicable, the Commercial Computer Software
and Commercial Computer Software Documentation are being licensed to U.S. Government end users (A)
only as Commercial Items and (B) with only those rights as are granted to all other end users pursuant to
the terms and conditions herein.

NOTICE TO USER:
THIS IS A CONTRACT. BY INSTALLING THIS SOFTWARE YOU ACCEPT ALL THE TERMS AND
CONDITIONS OF THIS AGREEMENT.

Unpublished-rights reserved under the copyright laws of the United States.

MKS Instruments, Inc., 90 Industrial Way, Wilmington, MA 01887

MKS, Microvision, Microvision-IP, e-Vision, e-Vision Plus, HPQ2, HPQ-IP, EasyView and Process Eye
Professional are trademarks of MKS Instruments.

Process Eye Professional V5 –SP104008.100 August 2005 4

 Contents
Licence Terms and Conditions 3
I. Getting Help 8
II. Introduction 9
Process Eye Professional Overview 9
EasyView Overview 9
Topics Covered by this Manual 9
An RGA as a Source of Data 10
Connecting Control Units 10
III. Software Installation Pre-requisites 11
Chapter 1 – Software Installation 12
1.1 Administrative Installation Using the Administrative Assistant 12
1.2 Administrative Options 15
1.3 Creating User Accounts 19
1.3.1 Overview 19
1.3.2 Create the “RGA User” Account 19
1.4 User Set-up 21
Chapter 2 – An Introduction to the RGA Device Manager 24
2.1 Hardware Management Overview 24
2.2 Finding Undiscovered Control Units 28
2.2.1 The Troubleshooting Wizard 29
Chapter 3 – The RGA Device Manager and Hardware Set-up 31
3.1 The Main Screen Elements 31
Title Bar 31
Control Unit List 31
Details 31
Configure 31
Troubleshoot 31
Help 31
Additional registered Connection 31
3.2 The Details Menu 32
3.3 The Configure Menu 32
3.4 The Hardware Set-up Utility 35
3.4.1 General 35
3.4.2 Trips 36
3.4.3 Analyzer 36
3.4.4 Inlets 37
3.4.5 Analog I/O 37
3.4.6 Digital I/O 38
3.4.7 Delays 39
3.4.8 Tools 40
3.4.9 Commit Changes 40
Chapter 4 – Getting Started with Process Eye Professional or EasyView 41
4.1 The Main Screen for Process Eye Professional 41
4.2 The Main Screen for EasyView 42
4.3 Running a Barchart with Additional Trend View 44
1 Title Bar 44
2 Menu Bar 44
3 Views Windows 44
4 Toolbars 44
5 Recipe List (Process Eye Professional only) 44
6a Status Windows (Process Eye Professional) 45
6b Status Windows and Control Panel (EasyView) 45
4.3 Saving Data to Disk 46
4.4 Adding Annotations 47
Chapter 5 – Displaying the Acquired Data 48
Overview 48
5.1 Editing the Barchart or Analog View Properties 50
5.1.1 X-Axis Properties 50
Minor Ticks 51
Show elapsed time in addition to scan number 51
Show real time in addition to scan number 51

Process Eye Professional V5 –SP104008.100 August 2005 5

 Annotations 51
5.1.2 Initial Y-axis Properties 51
Use data acquisition properties to set Y-axis properties 51
4- Or 5- decade log scale 51
Use the following explicit settings 51
Restrict these values to the maximum bounds of the acquired data 51
Grid 51
Minor Ticks 51
5.1.3 Subsequent Y-Axis Auto-Ranging Strategy 51
5.2 Editing the Trend View Properties 53
5.2.1 Editing a Trend Channel 53
Type 53
Editing a mass channel 54
Editing a user channel 55
Editing the channel display 55
5.2.2 Adding a Trend Pane 55
5.2.3 Configuring the Trend’s Y-Axis 56
Y-Axis Scale Properties 57
Y-Axis General Properties 58
Y-Axis Auto-range Properties 58
5.2.4 Configuring the trend time axis 59
Time axis properties 59
Elapsed time origin properties 60
5.2.5 Key Legend properties 60
5.3 Using the Toolbar Buttons to Change View Properties 61
5.4 Saving the View Properties (Process Eye Professional Only) 62
5.5 Managing Views Using View Manager (Process Eye Professional only) 63
5.5.1 Creating a New View 63
5.5.2 Editing a View in View Manager 64
5.5.3 Importing a View 64
5.5.4 Delete a View in View Manager 65
5.5.5 Setting a Particular View as the Default 65
Chapter 6 – Managing RGA Connections 66
6.1 Connection Information 66
6.2 Adding a Connection 67
6.3 Removing a Connection 68
6.4 Refresh Connections 68
6.5 Export Connection Information 68
6.6 Exit Connection Dialog 69
6.7 Hardware Information in the Status Pane (Process Eye Professional only) 69
6.7.1 No Instruments Connected Window 69
6.7.2 General Information Window 69
6.7.3 Digital IO Window 69
6.7.4 Remote Vacuum Controller (RVC) Window 70
6.7.5 Cirrus Window 70
6.8 Hardware Information and Connections in the Status Pane (EasyView only) 71
Chapter 7 – Using Process Eye Professional 72
7.1 Recipes in Process Eye Professional 72
7.2 Launching a Process Eye Recipe 73
7.3 Closing a Process Eye Recipe 73
7.4 Creating a New Recipe 74
7.5 Editing an Existing Recipe 74
7.6 Recipe Information in the Status Pane 75
7.6.1 Recipe Information View in the Status Window 75
7.6.2 Instrument Status View in the Status Window 75
7.6.3 Ion Source Settings View in the Status Window 75
7.6.4 Tuning View in the Status Window 76
7.6.5 The Status Window for the Start-up Recipe 76
Chapter 8 – Using EasyView 77
Overview 77
8.1 EasyView Toolbars 78
8.2 Analog Mode 79

Process Eye Professional V5 –SP104008.100 August 2005 6

 8.3 Barchart Mode 81
8.4 Leak Check Mode 83
8.5 Peak Jump Mode 85
8.6 Disk Store 87
8.7 EasyView Diagnostics 89
8.8 EasyView Tuning 90
8.9 EasyView Calibration - Faraday 92
8.10 EasyView Calibration - Multiplier 94
8.11 Degas 96
8.12 Remote Vacuum Controller (RVC) 96
8.13 Cirrus 97
Chapter 9 – Calibrating the RGA Using Process Eye Professional 98
Overview 98
9.1 Defining a Faraday Calibration 99
9.2 Defining a Multiplier Calibration Recipe 102
9.3 Running a Faraday or Multiplier Calibration 105
9.4 Calibration Alignment and Stability 107
Chapter 10 – Customising the Workspace 108
10.1 Modifying the Toolbars 109
10.1.1 The Default Toolbar 109
10.1.2 Window Arrangement Toolbar 109
10.1.3 Trend Display Toolbar 110
10.1.4 Chart Display Toolbar 110
10.1.5 Scan Navigation Toolbar 110
10.1.6 Interactive Scan Navigation Toolbar 111
10.1.7 Customizing Toolbars 112
10.2 – Graph Preferences 114
10.3 Other Preferences 115
10.3.1 Units of Pressure 115
10.3.2 Auto View to front 116
10.3.3 Show recipe error message boxes (Process Eye Professional) 117
Chapter 11 – The Main Application Menus 118
11.1.1 Recipe Menu 118
11.1.2 Instruments Pull-Down Menu (Process Eye Professional only) 118
11.1.3 View Pull-Down Menu 118
Toolbars 118
The Status Bar 119
Recipe List Window 119
Show Instruments 120
Show Dates 120
Properties 121
11.1.4 Window pull down menu 122
New Trend Window 122
Arrange All Windows 122
Bring Recipe to Front 123
Cascade Recipe 123
Tile Recipe Horizontally 123
Tile Recipe Vertically 123
Selecting Individual View 123
11.1.5 Help Pull down Menu 124
Chapter 12 – Printing 125
12.1.1 Print Setup 125
Printing a View 125
Chapter 13 – Process Eye Tools 127
13.1 Backup and Recover 127
13.2 Computer Lock 128
13.3 Process Eye Watchdog 130
Appendix 1 – Network Hardware and IP Addresses 131

Process Eye Professional V5 –SP104008.100 August 2005 7

I. Getting Help

Much of the application software suite has online context sensitive help. Please use this along with the
reference material in this manual as a starting point for getting help.

We are always pleased to provide personal assistance where we can. If you are experiencing difficulties or
need further help, feel free to call your local MKS Spectra facility and ask for the Customer Support Group.
Please have the following information ready so that our technical staff may help you quickly and effectively:

The serial numbers of the analyser and control unit; each of these numbers begins with the letters “MKS” or
“LM”

The Process Eye or EasyView software version number; this is written on the software CD ROM and can also
be found on screen by selecting Help | About from the menu-bar.

The operating system used and any Service Packs which have been applied.

Support Contact Telephone Numbers:

United Kingdom
+44 (0) 1270 250150

North America
+1 (408) 778-6060
1-800-VAC CHECK

Process Eye Professional V5 –SP104008.100 August 2005 8

II. Introduction

The MKS software covered by this manual is designed to operate with the full range of MKS Spectra “smart
head” instruments such as Microvision, e-Vision and HPQ2.

The software will run under Windows 98SE/ME/NT4/2000 and Windows XP operating systems. No other
versions of Windows are suitable.

Note: This manual is to be used in conjunction with version 5.20 onwards of Process Eye Professional or
EasyView. If you are currently using an earlier version please contact your local MKS Spectra representative
to discuss upgrade options.

Process Eye Professional Overview

The Process Eye Professional package is designed to monitor partial pressures and optionally, analog and
digital inputs, in a production environment where it is essential to observe and record the current status of
the process, while simultaneously reviewing historical events in both the current and archived runs. In
addition, complex comparisons, including statistical comparisons, can be made in real time.

The data acquisition is fast and covers a wide dynamic range of pressures so that some or all of the partial
pressures, along with analog and digital inputs, can be measured and stored, while only data of interest is
displayed.

Traditionally RGA operation has been based around a series of scanning modes such as bar chart, analog
scan and multi-trend. In Process Eye Professional, a scan can be made up of any number of mass scan
measurements that acquire bar chart or analog data and mass reading measurements that deal with single
masses. User measurements that may be the result of a calculation can also be incorporated into the scan
along with data from another source.

The package has been designed to be configured by the process engineer, who can set up a number of pre-
set configurations called “recipes” for various production requirements. These can then be selected by an
operator with a single click. If you install Process Eye Professional, the functionality of EasyView is provided
as one of the pre-installed “recipes”.

EasyView Overview
The EasyView package is designed to provide an easy-to-use working environment in which to use an MKS
RGA. While sharing the features of the Process Eye Professional package such as acquisition speed and wide
dynamic range, the package is fully interactive. EasyView contains all the same capabilities of data
acquisition, storing to disk, sensor calibration and degassing the ion source as Process Eye Professional and
is compatible with external hardware such as a Remote Vacuum Controller or a Cirrus bench top system.

Topics Covered by this Manual

The manual starts with the installation of the software and hardware. There are sections on Getting Started,
acquiring data and displaying data in ways that suit your pattern of work. Although Process Eye Professional
and EasyView adopt very different approaches to the user interface and experience, there is much in
common. Where necessary the manual indicates the differences between the two software applications, but
these sections have been kept to a minimum.

The complete suite of applications includes the Recall program for reviewing historical RGA data saved to
disk, and, for Process Eye Professional, the Recipe Wizard application, which generates recipes automatically
based on a wizard-style user interface. These applications have separate manuals.

Process Eye Professional V5 –SP104008.100 August 2005 9

An RGA as a Source of Data
This manual uses client server concepts to describe the mechanism of acquiring data and displaying it for the
user. The application software (Process Eye Professional or EasyView) is the client. The control unit is the
server, since it is the source of data. Network enabled instruments, such as the e-Vision and Microvision
Plus-IP have their data servers built in. Serial instruments such as the Microvision Plus must be connected to
a PC that runs server software that is capable of multiplexing more than one serial instrument and acting as
the data server to the connecting client. This Windows software is referred to as the ‘Local RGA Server’.

The client application and the data server communicate using a proprietary MKS ASCII protocol. If you want
to write your own client software, or to integrate RGA’s into your existing system control software, MKS
provides a software development kit (SDK) for application developers as a separate product.

Connecting Control Units

The Microvision Plus and HPQ2 smart head control unit connects to the PC using a serial interface that may
be RS232 or RS422. RS485 is not supported.

Microvision Plus-IP and HPQ2-IP control units, connect via a standard network interface. The serial RS232
connection on the rear panel of these instruments should not be used for general data acquisition.
On very rare occasions it may be necessary to use it for diagnostic purposes.

The e-Vision and e-Vision Plus control units connect exclusively using a standard network interface.

For the greatest security and reliability of data MKS recommends that networked instruments are on their
own physical network and that the computer that controls them have a dedicated separate network card.
However, this may not always be practical or desirable, and it is quite possible to run these control units on a
business or office network.

The control unit must be one suitably configured to run with Process Eye Professional or EasyView. If the
control unit was supplied with another software package or a previous version of Process Eye or was not
obtained directly from MKS or one of its agents or distributors, please contact your local MKS Spectra facility
for upgrade instructions.

Process Eye Professional V5 –SP104008.100 August 2005 10

III. Software Installation Pre-requisites

The full Process Eye Professional and EasyView software runs on any of the following operating
systems:

Windows XP
Windows 2000
Windows NT4 with service pack 6
Windows Me
Windows 98se

The Demonstration CD software runs only on Windows 2000 or XP and additionally requires a screen
resolution of at least 1024 x 768 pixels.

The TOOLweb RGA version of Process Eye Professional requires that Internet Information Services (IIS) is
pre-installed. You can do this from Control Panel and Add / Remove Programs. Select the Add / Remove
Windows Components option. If you are installing the TOOLweb RGA version of Process Eye Professional,
please read the additional installation instructions provided as a help file on the CD-ROM.

Before you start to install your RGA application software make sure you have fitted and pre-configured any
plug-in communication cards you may require.

You must be an administrator of the computer to install the software. However, once the software has been
installed you can run it with simple ‘user’ privileges. MKS recommends that you do so, since this is a key
component in any strategy for preventing malicious software infecting the system.

The following sections detail the software installation, creating an RGA User account and configuration of the
main application program.

Process Eye Professional V5 –SP104008.100 August 2005 11

Chapter 1 – Software Installation

Insert the CD-ROM in the drive; if it does not auto-run, click the setup.exe application in the root folder.
From the CD browser select the option to install the software. This will launch the Administrative
Assistant that will guide you through the complete installation process.

1.1 Administrative Installation Using the Administrative Assistant

The Administrative Assistant contains full context-

sensitive on-line help.

You can access this help at any time either by clicking

the Help button or simply by pressing the F1
function key on your keyboard.

You must agree to the terms of the software license

in order to proceed with the installation. The license
terms are printed in the preface of this manual.

The CD-ROM can be used to install one of several

different set-ups of RGA software.

The Quick Set-up Code determines exactly what

software is installed. The correct code for your
installation is printed on the label of your CD-ROM.

You must enter the code on this page of the

Assistant. The code is not case sensitive.

Process Eye Professional V5 –SP104008.100 August 2005 12

The pages that follow depend on the set-up code entered and the Windows operating system installed on
your computer. This manual shows the most common dialogs from a Windows XP install. Your set-up may
include others, which should be self-explanatory. Remember that you can refer to the on-line help for any
pages not shown in this manual.

You can choose the file locations for program files

and system data.

You should always install the program files to your

locale specific Program Files location since Windows
prevents any changes to this area of the disk by any
users other than administrators.

In contrast, the location for data needs to be

accessible to everyone who will use the RGA because
these settings will need to be changed at run-time.

If either of these folders needs to be created, the

Assistant will do this for you.

A Complete Install allows you to run RGA’s on this

computer and to save the data that is generated.

Sometimes you will want to install the software on a

computer that will only be used to recall and review
data files that were stored somewhere else.

In this case you do not need all the real-time

applications and you can elect to perform an Off-line
Installation.

MKS recommends that you keep your computer up-

to-date with the latest service packs from Microsoft.

If you do not have the latest Windows service packs

installed for the operating system and for Internet
Explorer, the Assistant will optionally apply them for
you.

Process Eye Professional V5 –SP104008.100 August 2005 13

 Once the Assistant has completed the initial checks it
is ready to install the correct software for your chosen
set-up code.

The complete installation process may require the

Assistant to perform several tasks which are itemised
on this screen.

Some set-ups may involve a reboot of the computer

part way through. All these steps will be handled
automatically.

Process Eye Professional V5 –SP104008.100 August 2005 14

1.2 Administrative Options

Having completed the installation of the necessary

files to your hard drive, the final stages of the set-up
process involve the configuration of several
administrative set-up options.

You can re-run this section of the Assistant at any

time after installing the software, so any choices you
make now may be changed later.

The first option on this page is to choose the data

acquisition mode. Usually you will select the first
option as indicated.

In Normal (real) mode the software connects to real hardware to acquire real RGA data.

In Demonstration mode the software connects to any number of ‘Virtual RGA’s’ that, although they exist
purely in the computer’s memory, behave exactly like a real instrument

If this option is selected, the software will only connect to virtual RGA’s.
(Note: strictly this is true only for Windows XP with the firewall enabled. Where no firewall is in place you
would be able to connect to real network instruments in Demonstration mode.)

In Mixed mode the software will connect to both real and virtual hardware. This option is primarily intended
for RGA software developers.

Process Eye Professional V5 –SP104008.100 August 2005 15

 If multiple users log on to this computer, you can
choose how they interact with the RGA software.

If you want each logged on user to have a separate

location where they can save their data and settings,
choose the first option on this page.
The Assistant will set up folder locations beneath
each user’s ‘My Documents’ folder.

However, it is perhaps more common that you will

want to work in such a way that all the individual log-
on users will share access to common data and
settings. In this case you must select a folder that is
accessible to all users.

The default location for this choice is the same folder that you chose earlier for the common system settings.
You can change this selection by clicking the Change button.

If you elect to have a common location, you may choose the common units you will use for pressure. The
Event Log button allows you to change some advanced settings that are also common to all users.

If you chose to have a common location for all users,

Process Eye Professional users can then choose
whether to maintain ‘recipes’ on this computer (the
default) or to maintain a common set of recipes for
multiple computers at one central location.

This is an advanced feature, which will be of interest

only to users who are installing the software in a
factory environment.

The Process Eye Professional software comes with several Security Features. By default these are usually
un-checked (off). If you have never used MKS RGA software before, you are advised initially to leave the
options un-checked. You can re-run the Administrative Assistant at a later time when you are more familiar
with the product. These features are not part of the EasyView package.

The Watchdog is a system tray application that

continually checks that the main Process Eye
application is running correctly. If it detects that it is
not, it can shut it down and restart it.

The Restricted user interface does not include

menus and buttons for changing or launching recipes.

You can prevent users from Changing recipes using

the recipe-editing wizard.

You can Lock down the computer so that only

authorised users can interact with the computer
through the mouse and keyboard.

Process Eye Professional V5 –SP104008.100 August 2005 16

 The RGA software continuously attempts to connect
to an RGA instrument on all of your computer’s serial
ports unless you identify particular ports as being
‘RGA-disabled’.

If you plan to connect RS232 or RS422 serial

instruments to this computer, you will want to ensure
all the serial ports to which you might connect an
RGA are ‘RGA-enabled’.
By the same token be sure to ‘RGA-disable’ any ports
to which you connect other devices

If you only use RGA’s with network connectivity, you

should click the Uncheck All button to prevent the
RGA software from continuously checking to see if
there is an instrument attached.

If you have Windows XP installed, the Assistant will display the Windows Firewall page.

The Windows firewall became a default feature of

Windows XP with the release of service pack 2.
The Assistant will configure your XP firewall
automatically so that the correct network ports are
enabled to allow the RGA software to run correctly.

If you have Windows XP but do not have service pack

2 installed, the Assistant will show this page but will
not make any changes to the firewall settings.
If you install service pack 2 at a later date, be sure to
re-run the Assistant so that the firewall can be set
correctly.

You may need to open the firewall to allow one or more of the following.
• Allow network instruments to communicate to this computer
• Allow other computers to which serial instruments are attached to pass data to this computer
• Allow an instance of the RGA software installed on another computer to access serial instruments
connected to this one.

You can choose to allow any computer to have access to the network ports required by the MKS software, or
you can choose to restrict the access to your local subnet(s) only. If you are familiar with the management
of the firewall through Control Panel, you will recognise this restricted access as being the settings behind
the Security Center ‘Scope’ button.

The default setting is to allow restricted scope.

Note that the Assistant will only set up the Windows XP firewall. It cannot configure any other firewall
software.

Process Eye Professional V5 –SP104008.100 August 2005 17

 This screen indicates that the Assistant has finished
requesting information from you and is ready to apply
the settings that you have entered.

If you choose Cancel at this point, none of the

Administrative Options that you have entered will be
applied.

The Administrative Assistant has finished.

You can re-run the Assistant and change any of the optional settings by selecting Start | Programs | MKS
RGA Applications | Tools | Administrative Assistant.

If you are installing the software for the first time, this completes the first, administrative part of the
procedure. You will complete the entire installation when you run the software as the RGA User for the first
time.

MKS strongly recommends that you create limited user privilege accounts for users of the RGA software.
This procedure is detailed in the following section.

Process Eye Professional V5 –SP104008.100 August 2005 18

1.3 Creating User Accounts
1.3.1 Overview
The following section describes how to create a new local user and assign local user rights using the
Windows XP environment as a guide.

This is not common for all Windows operating systems; advice from your I.T representative or MKS Spectra
should be sought if you are unsure of how to continue, or the PC is part of your company network.

You will need to be logged on to the PC with an administrative account to create the RGA User account with
assigned User rights.

If your PC is on a network, the RGA User will require a Domain account. Seek advice from your IT Staff if this
is the case.

1.3.2 Create the “RGA User” Account

Click on the Start button, right-click on the My Computer entry and

select Manage from the menu.

In the Computer Management dialog, click on

the Local Users and Groups entry to expand
the list and show the Users and Groups folders.

Process Eye Professional V5 –SP104008.100 August 2005 19

 Right-click on the Users folder and select New
User from the list.

It is recommended that you use the name RGA User

to easily identify the account.

You can enter a full name, description and password

if you wish.

Check the User cannot change password and

Password never expires boxes as shown.

Click on the Create button and then click the

Close button to return to the Computer
Management dialog.

At this point, you should now log-off as the Administrator and log-on as the RGA User to continue with the
Software Setup section.

Process Eye Professional V5 –SP104008.100 August 2005 20

1.4 User Set-up

You can run the User Set-up application at any time

by selecting User Set-up from Start | Programs |
MKS RGA Applications | Tools, but it will launch
automatically the first time that you run a new or
upgraded version of the RGA software.

Once again you will notice that there is full context-

sensitive on-line help available by pressing the F1
function key or by clicking the Help button.

The pages that follow depend on the main set-up code and also on some of the options selected by the
administrator when the Administrative Assistant was run.

The User Set-up Wizard will install ‘recipes’ to the

relevant target location. If the recipe collection that
you want to install is listed, simply check the relevant
box.

If you have been provided with a collection of recipes

on a separate floppy disk or CD-ROM or by e-mail,
click the Have Disk button.

Insert the disk and select it from the drop-down list,

then click OK. Now the recipe collection will appear
in the list.

If the recipe collection has been e-mailed to you and

the attachment is on your hard drive, select Browse
from the drop-down list and find the .lst file that holds the recipe collection information.

The User Set-up Wizard can launch the RGA

Device Manager application.

You use this for all aspects of hardware set-up. This

application is described in full detail in chapters 2 and
3.

If you are installing the software for the first time by

working step by step through this manual, it is easiest
to select Skip hardware auto-detection at the
present time. You will learn how to install hardware
in the next chapter.

Process Eye Professional V5 –SP104008.100 August 2005 21

 If the administrator elected to have each log-on user
define their own personal settings, you may choose
the units that you would like to use.

If the administrator elected to have each log-on user

define their own personal settings, you may choose
the location for recipe and data files.

You must choose a location somewhere beneath your

personal My Documents folder.

The Event Log button sets some advanced settings

relating to the maximum file size for the Process Eye
master log file.
This file records information such as when the
application runs, when hardware was calibrated and
when recipe errors are found. The default is to limit
this file size to 100 Kb.

The last page of the User Set-up Wizard offers you

the choice of running one of the main applications
directly when the installation completes.

If you have not yet installed your hardware, leave

these checkboxes unchecked.

When you click the Finish button, the selections that

you have made in the Wizard are installed.

Process Eye Professional V5 –SP104008.100 August 2005 22

 If you selected recipes to be installed, a report history
of all the recipes that the Wizard has installed to date,
including those installed on the current session is
displayed.

If you have not yet installed your RGA hardware, please continue with the next chapter of this manual.

Process Eye Professional V5 –SP104008.100 August 2005 23

Chapter 2 – An Introduction to the RGA Device Manager

2.1 Hardware Management Overview

The RGA Device Manager application is the main application for all aspects of hardware management
including:

• Installation
• Configuration
• Access control
• Network configuration

The RGA Device Manager application is used for all MKS RGA control units including:

• Microvision Plus
• HPQ2 and HPQ2S
• e-Vision and e-Vision Plus
• Microvision-IP and HPQ2-IP

You can run the RGA Device Manager application from either
Start | Programs | MKS RGA Applications
Or from the relevant page in User Set-up, accessed from
Start | Programs | MKS RGA Applications | Tools

With everything configured and working correctly the main window looks like this.

Apart from the application name itself, the title bar indicates the name of this computer and its full IP
address and subnet mask. (If you have multiple network cards fitted, you can find the network properties of
each card by clicking the Details button.) If you need to connect to network RGA’s it is important that you
know the IP address of this computer.

The main window features a list of all the RGA’s that are connected to this computer. They may be:
Serial instruments connected to COM ports on this computer
Serial instruments connected to a different computer
Network instruments

The list box displays:

The Serial Number of the instrument - This is a unique ID always prefixed with LM.
The Friendly Name - You choose this name, it is easier to locate a specific RGA by name rather than its
serial number.
The Network Location.

Process Eye Professional V5 –SP104008.100 August 2005 24

The Type of Connection – serial or, if a network instrument, whether the address is fixed or assigned by a
DHCP server.
The Access Control settings – whether you want exclusive or shared access to the control unit.
The current Status of the control unit – whether it is available or in use.

Other aspects of the main window are described later in this chapter.

If you are installing a control unit for the first time, it is very unlikely that it will show up in the list with a
green tick, indicating that it is ready for immediate use. It is much more likely that it will have a red cross
beside it as shown in the next screen view.

Whenever you see an item with a red cross you should double-
click the item in the list to bring up the More Details pop-up
dialog as shown.

This dialog displays much more information about the state of the instrument than can be displayed in the
main window list.

If the control unit needs some form of installation or configuration, the Configure Now button will be
enabled. When you click this button, RGA Device Manager will guide you through the procedure necessary
to get you going.

Here are some examples of what may be required:

Give the control unit a ‘friendly name’.
Assign the control unit a new IP address (network instruments only)
Download an upgrade to the embedded software.
Set the pressure reduction factors for associated inlet hardware

Sometimes it may be necessary to do more than one of these things. If so, simply double click the item in
the list and click Configure Now again to perform each task in turn.

Process Eye Professional V5 –SP104008.100 August 2005 25

 Some control units will require a password in order to change these
important settings.

If you are asked for a password by the dialog shown, the password is the
same as the Quick Set-up Code that you used to install the software initially.

If you are using browser software to browse to a network instrument, the password to configure the control
unit is MKS all in upper case.

If you are requested to enter a friendly name for the instrument in a dialog
such as the one shown, you must enter a name of your choice that
describes the location or function of the RGA system.

If you have multiple RGA’s, you can then easily to distinguish one from
another. Use simple alphanumeric characters for your name. You are
prohibited from using characters such as @ # % [ ] or any quote marks.

If you have to enter a new IP address for the control unit, it is important that you understand how this
address is chosen. There should be someone in your organisation that is responsible for networks and the
assignment of addresses. Please be sure to discuss with your network administrator what you
plan to do.

You have a basic choice between assigning a fixed IP address and having a computer on the network assign
one for you. This latter case is called DHCP addressing, but
please ensure that you only select this option if you have a
DHCP server on the same network as the control unit.

If you do not have, or do not want to use a DHCP server, you

must assign a unique fixed address that ‘matches’ the address
of the computer that will control it.

For example;
If your computer’s address is 10.20.30.41 with a subnet mask of
255.255.255.0, you should choose a fixed address that is
10.20.30.xxx, where xxx is a number between 1 and 254 that is
not used by any other device on the physical network. Never
use 0 or 255 for the fourth number. These numbers have a special meaning on a network. The subnet mask
for the control unit will almost always be the same as the subnet mask of your computer.

If you are in any doubt about IP addressing, please read Appendix 1 of this manual or read the on-line help
on the subject by pressing the F1 key.

Process Eye Professional V5 –SP104008.100 August 2005 26

Provided you give the control unit a unique address on your subnet, RGA Device Manager will show it with a
green tick.

Once your hardware is installed the RGA Device Manager will show it as ready for use.

The main window of the RGA Device Manger is a live real-time view of all the RGA’s on your system. The list
updates every few seconds. Please wait a few seconds after installing a new control unit, or after changing
its configuration. You must allow the unit time to reboot and for RGA Device Manager to acquire the new
information about it.

Process Eye Professional V5 –SP104008.100 August 2005 27

2.2 Finding Undiscovered Control Units
Although the RGA Device Manager will usually find any control unit, there may be occasions when you expect
to find one in the list but it is absent. There will usually be a simple reason for this; use the Troubleshoot
button to launch a Wizard to help you get up and running quickly.

Examples of likely reasons for failing to discover a control unit are that the Windows firewall is blocking
communications or that the serial port is not ‘RGA-enabled’.

The Troubleshooting Wizard can diagnose these and other problems for you and can usually bring network
instruments on-line. But before you run the Wizard, please check that the cables are installed correctly and
that the instrument is powered up. Also, if you have used the control unit successfully before, take a
moment to consider what might have changed recently with your computer’s set-up. Have you changed
your network settings? If so, please run the Administrative set-up first. This will ensure that your firewall
settings are up-to-date.

Note: The Troubleshooting Wizard is only available from version 5.21 of the application software.

Process Eye Professional V5 –SP104008.100 August 2005 28

2.2.1 The Troubleshooting Wizard

Clicking the Troubleshoot button on the RGA Device

Manager dialog starts the Troubleshooting Wizard.

Enter the serial number of the instrument that you want

to locate.

Be sure to enter it carefully. You do not want to re-

configure the wrong instrument!

If you have used the troubleshooting wizard with this

instrument before, you will find its serial number
already present in the drop down list.

If you chose a serial instrument, you will have to enter the COM port number where the serial cable is
connected.

If you chose a network instrument, choose from one of

these options:

The control unit should get its IP address from a DHCP

server on its network.

The control unit should have a fixed IP address which

you must enter in the form of an address and a subnet
mask.

Please understand that the information that you enter here is the information that you want the control unit
to end up with if it is found. It is not necessarily the information that the control unit has now. You may not
even know what address the control unit currently has.

Process Eye Professional V5 –SP104008.100 August 2005 29

 If you can do so, enter the instruments status by
checking the LED’s on the instruments rear panel and
indicating the state of the LED’s on this page.

Note: the wizard may display a different page from the

one shown here depending on your particular control
unit.

Click Next to begin the test, which, depending on the

type of instrument, may take up to a minute.

When the test is complete, the Wizard displays a report

comprising of the following information:

The overall result

Suggested corrective actions
The individual test results
Additional diagnostic information that could be useful in
further dealing with the problem

The Save button allows you to save a copy of the report to show it to your system administrator for
example. You can choose between one of two different report formats – plain text or html.

The Open button displays the report in html format in your browser making it easier to read. You can have
the wizard always open the report in your browser by checking the check box.

This completes the introduction to the management of RGA hardware. The next chapter examines the RGA
Device Manager application in more detail.

Process Eye Professional V5 –SP104008.100 August 2005 30

Chapter 3 – The RGA Device Manager and Hardware Set-up

The previous chapter gave a brief introduction to RGA Device Manager. It showed how you might use the
application to install a new RGA; this chapter describes all the functionality of the program.

3.1 The Main Screen Elements

Title Bar
The title bar displays your computer name, IP address and subnet mask enclosed in square brackets.

You already know from the previous chapter that, using the graphic above as an example, the computer
named xpsp2installpc is on the 10.10.54.0 IP address range and that it would be able to communicate with
network instruments having unique addresses on the same range.

Control Unit List

The control unit list displays all discovered control units. Each entry displays information about the unit’s
serial number, name, its network location, address type, its accessibility and status.

You can double click an item in the list to view more verbose details about the highlighted control unit, or
you can right mouse click an item and bring up a context-sensitive pop-up menu that offers all the available
actions that can be taken.

Details
The Details button displays a pop-up menu with more options about the information in the list.

Configure
The Configure button displays a menu of relevant options relating to the configuration and set-up of an RGA.

Troubleshoot
The Troubleshoot button launches the Troubleshooting Wizard that can assist you in diagnosing
hardware communications problems.

Help
The Help button launches the RGA Device Manager Help application at its ‘home page’, but you can access
context-sensitive help at any time by pressing the F1 key on your keyboard.

Additional registered Connection

If you have previously set up access rights to a control unit that cannot now be discovered, the unit’s details
are indicated in the additional registered connections panel. The Details button inside this panel gives more
information.

Process Eye Professional V5 –SP104008.100 August 2005 31

Typically, if you no longer use the control unit(s) referred to, you can remove these connections since
unused registered connections increase the time taken for Process Eye Professional or EasyView to start up.

3.2 The Details Menu

The items on the details menu are accessed either by clicking the Details button on the right hand side of
the window, or by right mouse clicking the item in the control unit list.

The More Details dialog displays the information about the control unit in more detail. It is the default
action when you double click an item in the list. If the RGA that you are interested in has a red cross beside
it, you should always select this menu item to find out more about the problem.

The listed items are continuously updated every few seconds. When the application first runs and whenever
you select Refresh List or press the F5 key, RGA Device Manager writes an auto-discovery log of all the
messages received from the connected hardware. You can view this log by choosing the menu item from
the Details button. It can sometimes indicate the cause of a communications problem.

3.3 The Configure Menu

You access the Configure menu either by right clicking on the list or by clicking the Configure button. The
menu offers the following options.

Browse to the instrument (network instruments only). Selecting this option will open your default
browser and navigate to the home page of the selected instrument. If the control unit is an e-Vision or
e-Vision Plus, this is the means by which you configure the control unit as well.
The password for configuration is MKS all in upper case.

Process Eye Professional V5 –SP104008.100 August 2005 32

Change the IP address (network instruments only). Selecting this option will lead to the IP address
configuration dialog described below.

Download is the process by which new embedded software is downloaded to the control unit. This
selection does not apply to e-Vision or e-Vision Plus, which have their software downloaded as a ‘package’.

Package Download (not serial instruments). A download package is a collection of files that are
downloaded to the control unit at one time. Package downloads use the File Transfer Protocol (FTP).

Selecting this menu item will launch the Package Download Wizard, which will guide you through the
steps necessary to download your selected package. Packages are supplied as executable files (*.exe).
Having selected the package to download (your CD-ROM will contain the most up-to-date package at the
time of delivery, but newer ones are released periodically), follow the steps explained by the Wizard
including the procedure to put the control unit into FTP mode for the file transfer itself.

Access Control. This menu selection leads to the Access Control dialog described in section 3.3. You
choose whether when Process Eye Professional or EasyView start up they attempt to gain exclusive access to
the selected RGA, or whether the control unit needs to be shared with users on other computers.

Install or configure instrument (not e-Vision or e-Vision Plus). This is the main selection for all aspects
of installation or configuration of your hardware. The Hardware Set-up application that is launched by this
menu selection is described in more detail in section 3.4.

Change the IP address. Always consult with your network administrator before changing the IP
address of a control unit. You must not choose an address that is used by another network
connection. If you are unsure, please read Appendix 1 or click the Help button or press the F1
key.

The IP Configuration Dialog

This dialog allows you to select the IP addressing mode (DHCP or

fixed).

If you choose a fixed address, you enter the address and subnet
mask. The IP addresses associated with network connections on this
computer are shown in order to help you check that you are entering
a valid address.

Almost always you will be entering a fixed address that differs from
your computer address only in the number following the final ‘dot’.

If you want to check that the address change was successful, check the Browse to this instrument
checkbox. You should see the instrument’s home page.

The Download Dialog. You have the option to select the latest core, latest application or to select an
individual file to download. IP control units have the additional option to download the latest embedded
server application. The RGA Device Manager will read the file version and ask you to confirm that you
want to replace the existing version with the new version.

If you choose Cancel, the download will not proceed. Otherwise the
download process will take a few seconds, following which the control
unit will reboot.

During this time it may disappear from the RGA Device Manager list,
but after the reboot it will reappear once more.

Process Eye Professional V5 –SP104008.100 August 2005 33

The Access Control dialog. You will usually want to set up for the main RGA application to attempt to gain
exclusive access to your control units. However, you may be on a factory network where separate
computers are associated with individual control units.

In that case you should only check the box in this dialog for the RGA
that ‘belongs’ to you. The other RGA’s listed in the main window
should show No pre-connection in the Access column of the list.
This ensures that their users can access them when they need to.

If you have one RGA that you want to be able to control from two computer locations, select the option to
Share this instrument with other users. You will then connect to the RGA only when you need to.

Unless you have a good reason to do otherwise you should choose the settings shown in the graphic above.

Note that sharing does not mean that two users can have concurrent access to an RGA. Only one user at a
time can control an RGA. By selecting the exclusive access option you are requesting the run-time software
to connect to the RGA as soon as it starts up, thereby preventing anyone else from connecting even though
you may not be actually using it to acquire data.

Process Eye Professional V5 –SP104008.100 August 2005 34

3.4 The Hardware Set-up Utility
This utility is not used with e-Vision or e-Vision Plus. If you have just taken delivery of your control unit from
MKS, it will have been configured correctly at the factory. You should not need to use this utility in order to
get you started.

This utility is the means by which you modify the hardware configuration of your control units. You will need
to enter a password in order to make changes to control units. However, if you leave the password box
blank, you may view all the settings without changing them.

The configurable options are broken down into eight ‘pages’ of settings shown below.

The eight tabs are:

• General
• Trips
• Analyzer
• Inlets
• Analog I/O
• Digital I/O
• Delays
• Tools

3.4.1 General

The General tab displays many fixed items of information,

including the embedded software versions. The three user-
configurable settings are the name assigned to the control
unit, the mains frequency and the filament type. You may
also use this page as another way to download new
embedded software to the control unit.

Be sure to set the mains frequency to the correct value for

your locale. Selecting the wrong value can give rise to
unwanted noise on the spectra acquired.

Process Eye Professional V5 –SP104008.100 August 2005 35

3.4.2 Trips
This tab allows you to set the behaviour of the filament and
multiplier protection trips.

The electron emission current is continuously monitored by

the control electronics.
Checking the first check box ensures that the filament is
turned off if the emission current cannot be maintained.

If left un-checked, the filament will remain on but the peak

data acquired may be subject to considerable error.

You can elect to have the filament turn off automatically after
a predetermined number of minutes of unattended use.

It is recommended that the external X-trip jack socket is used

to provide some interlocking of the filament circuit to an
external hardware contact.
In this case you would select the Filament protection
option from the drop-down list.

In some installations the external contact is used to actually turn the filament on or off. If this is the case,
choose the Filament control option. You should not normally choose the No protection option.

Your choice for the final filament trip check box selection probably depends on the local conditions of the
way you work. Sometimes it is advisable for the software to turn off the filaments automatically when you
quit the RGA application. In other cases, you may prefer that they be left on all the time. You should only
adopt this approach if you are sure that the filaments are well interlocked at the hardware level.

The two options for multiplier trips are checked by default. The first turns off the multiplier if the filament is
not on. The second automatically turns off the multiplier during a bake on a system with an MKS Remote
Vacuum Controller (RVC) or an MKS Cirrus system.

3.4.3 Analyzer
This tab shows the ion source and mass filter configuration properties for each of six possible groups of
settings. You select the information displayed by choosing a Configuration from the drop down list at the
top of the page.

In the example shown the settings relate to the Base

Pressure RGA configuration in which the electron emission
current is 0.39mA and the ion energy is 7eV.

The calibration sensitivity in units of Amps per unit of pressure

is shown for the Faraday detector using filament #1.

You can view the sensitivities of the other detector settings by

clicking repeatedly on the More Detectors icon.

The Filter Configuration is shown in the lower panel. There

are four integer numbers that set the alignment and resolution
at low and high mass.

Click the Copy to All button to apply the alignment and

resolution settings indicated for the current configuration
(Base Pressure RGA in the example shown) to the other five
ion source configurations.

Note: the following Reset functions require version 5.21.

Process Eye Professional V5 –SP104008.100 August 2005 36

Click the Reset button to reset the settings for the current ion source configuration to the factory default
values.
Click Reset All to reset all six ion source configurations to their factory default values. In both cases you
can select which features to reset as shown here.

You can individually reset:

The source parameters, such as ion and electron energy.

The basic ion source (Faraday) calibration sensitivity.
The filter alignment and resolution settings.
Where a multiplier is fitted you can reset the multiplier detector
sensitivities. Depending on your choice of options, you may be able
to reset either the multiplier sensitivity or gain to the factory default.

3.4.4 Inlets
This tab will only be relevant if you have an RGA with an inlet system. Where this is the case you must
configure each inlet so that its inlet factor (pressure reduction factor) is correct. If you obtained the
complete system from MKS, you will have been informed what the inlet factors for your system are.

Select an item from the drop down list that describes as

closely as possible the inlet that is fitted – for example a ‘x10
orifice’.

In the pressure reduction box enter the actual reduction factor

to use, which may be a more precise figure – for example
10.6.

If you want to be able to calibrate the inlet at run-time, check

the Allow calibration box.

Please be aware that calibrating an inlet requires that you

know both the upstream pressure and the ion source pressure
of the RGA analyser.

3.4.5 Analog I/O

This tab displays the configuration of the Analog I/O connector on the rear panel of the control unit.

If, as in the example shown, the control unit is one with a

pressure gauge attached, select the type of gauge from the
list in the top panel.

Note that only HPQ2S RGA’s are equipped with an external

gauge for rollover correction. All other instruments will show
not applicable in the gauge type list.

Process Eye Professional V5 –SP104008.100 August 2005 37

 The Properties button shows a dialog in which you can change the
acquisition frequency/accuracy. The software automatically converts the
voltage to a pressure according to the manufacturer’s calibration. You
can change this calibration with a factor in v5.21 onwards. Values in
excess of one increase the pressure relative to the manufacturer’s
calibration and values less than 1 reduce it.

The dialog also displays the connector pins used by the gauge.

When a gauge is used for rollover correction you can modify or reset the algorithm by clicking the
Algorithm button. This is an advanced feature that is not described further in this manual. You should
only ever use non-default settings if instructed to do so by MKS support personnel.

If you do not have an external gauge, all the four inputs and one output are available for use within your
data acquisition recipes. The General Purpose I/O panel indicates the pins that can be used to connect
I/O to the control unit.

3.4.6 Digital I/O

This tab lists the inputs and outputs that have been enabled on the Digital I/O connector on the rear of the
control unit.

By default there are no I/O channels enabled but you can set
individual channels to be configured as inputs or outputs by
clicking the Change button.

This pops up a new dialog as shown here.

There are usually sixteen available channels of I/O,

although if you have an external gauge on the analog
input (as shown in this example), one or more channels
may be marked as reserved.

You cycle through the options of Not Used, Input and

Output simply by left mouse clicking on the icon in the
left-most column of the list.

The pin associated with the channel is indicated in the

fourth column.
The additional pins are described at the bottom of the
dialog.

The Options panel has the following features:

Process Eye Professional V5 –SP104008.100 August 2005 38

You can choose whether the outputs boot high or low – See below.
You can modify the deglitch time – See below.

When PB6 and/or PB7 are configured as outputs, you can optionally set a maximum permissible ‘on’ time for
these outputs only. Typically this is used for the control of a calibration gas sample bottle, in order to ensure
that the bottle contents are not inadvertently drained.

The When the control unit powers up, set the TTL levels of connected output option is used to
determine the state of the digital outputs at switch on. You will usually want to ensure that this corresponds
to your ‘safe’ state, which will depend on the nature of the circuit driven by the TTL output.

Note: Setting an output line in a recipe script to ‘False’ or zero always sets the TTL level low; setting it to
‘True’ or non-zero will set the level high. This is true whether the default On Power-up set output TTL
levels is high or low.

The digital lines, PB6 and PB7 differ from the other lines as they can be configured to revert to the selected
power-up state after a predetermined amount of time. This can be configured by checking the If PB6 or
PB7 are connected outputs box and entering the required time in seconds.

When enabled, the deglitch filter works by monitoring the data line for changes in state. If a change is
detected a timer will start, if no further changes of state are detected by the time the timer has reached the
deglitch time, the digital input line will change state.

If a change in state is detected before the timer has reached the deglitch time, no changes will be made to
the digital input line.

Note: If the digital input is continually changing state at a frequency faster then the set deglitch time, then
no changes in state will be reported.

Please read the relevant section of the control unit manual to find out how to wire external hardware to the
control unit.

3.4.7 Delays
This tab is an advanced feature. The control unit has a table
of software delays that control the length of transition states –
for example how long to wait when switching between a
Faraday and multiplier detector.

You should never normally need to change the delays from

the standard factory defaults. However, in exceptional
circumstances an MKS support engineer may recommend
changes to one or more of these standard settings.

This topic is not covered any further in this manual.

Process Eye Professional V5 –SP104008.100 August 2005 39

3.4.8 Tools
Using the features of this tab you can set options that apply to the application itself and you can perform
tasks such as back-up and restore of control unit settings.

If you want to bypass the password screen you can set this
option using the checkbox.

Usually in the context of Process Eye or EasyView you do not

have a choice of pressure units – they default to the option
chosen in the main set-up.

The tools available are:

Back-up – save all the control unit settings to a file.

Restore – restore all the control unit settings using a previously saved back-up.
Report – create a complete documented report on the current settings. You can save this to disk and/or
view it using your browser.

Please note that the back-up and report options act on the settings currently displayed on the pages of the
dialog. If you have made changes to the dialog and you do not commit these changes to the control unit by
clicking the OK button, the action will not reflect the true state of the control unit.

3.4.9 Commit Changes

You commit any changes to the control unit by clicking the OK button. All the configuration settings are
downloaded to the control unit and it will then reboot. If you want to leave the control unit unchanged, click
Cancel.

Process Eye Professional V5 –SP104008.100 August 2005 40

Chapter 4 – Getting Started with Process Eye Professional or
EasyView

Note: Once the software has been installed the CD is not required to run the RGA application suite.

4.1 The Main Screen for Process Eye Professional

To start the main Process Eye Professional program, click on:
Start | Programs | MKS RGA Applications | Process Eye Professional.

If you are already in Recipe Wizard, Process Eye Professional can be launched directly by clicking on the
Launch Process Eye button, or by selecting Recipe | Run Process Eye from the menu bar.

The main Process Eye window is displayed.

If you followed typical practice and specified

that you wanted exclusive access to one or
more RGA’s in the hardware installation, this
screen will show the connected instruments
details.

If you did not specify exclusive access to

an RGA during hardware installation, the
screen will be shown without any instrument
details. (See Section 3.3)

However, provided you have shared access

to at least one RGA you are ready to start
acquiring data.

You can check the RGA’s to which you have

access by clicking the Instruments |
Connections menu item. This dialog shows
all the control units to which you can
connect. If the list is empty, refer to
chapter 2.

Provided that your vacuum hardware is at a pressure that is safe for the RGA to be switched on, you are
ready to start using your RGA. This pressure is usually a value lower than 1e-3 torr/mbar (1e-1 Pa). If you
are ready to do so, double click the item in the Recipe List window titled ‘Barchart with Trend
Interactive’. Now proceed with section 4.3.

Process Eye Professional V5 –SP104008.100 August 2005 41

4.2 The Main Screen for EasyView
To start the main EasyView application program, click on:
Start | Programs | MKS RGA Applications | EasyView.

The main EasyView window is displayed. If you have just one RGA and you have exclusive access to it,
EasyView will connect immediately and the screen on the following page will be displayed. You are ready to
start acquiring data.

If you specified that you wanted either

shared or exclusive access to more than
one RGA in the hardware installation, this
screen will show all the accessible
instrument details.

If you did not specify either shared or

exclusive access to an RGA during
hardware installation, the screen will be
shown without any instrument details.

Click the Edit Connections button, then in

the dialog that follows click Add Connection
and check one of the checkboxes to select
an RGA to connect to. Refer to chapter 2
for more information.

Provided that your vacuum hardware is at a pressure that is safe for the RGA to be switched on, you are
ready to start using your RGA. This pressure is usually a value lower than 1e-3 torr/mbar (1e-1 Pa). If you
are ready to do so, double click the line containing the information about the RGA that you are ready to use.

Process Eye Professional V5 –SP104008.100 August 2005 42

 You will now see the main EasyView data
acquisition window.

In order to follow through the rest of this

chapter of the manual it is suggested that
you do the following.

Look at the area at the bottom of the main

window. Click on the barchart
icon. This will initiate the
barchart scan mode.

Then click on the Show Trend View icon

at the right hand end of the
Acquisition control toolbar. This
will add the optional trend view
to the display.

Your screen should now look

similar to this.

Process Eye Professional V5 –SP104008.100 August 2005 43

 4.3 Running a Barchart with Additional Trend View
The main Process Eye Professional or EasyView screen is where most of your time will probably be spent.
It provides a view onto the RGA data being acquired; in EasyView it has the control panel that you use to
determine what the RGA does, while in Process Eye Professional it provides details of installed recipes,
instrument information, alarm events and communications status.

1
2 This shows a typical screen for Process
4 Eye Professional. The screen for
EasyView was shown on the previous
page. Both screens share many common
elements.

5 3 3

1 Title Bar
The Title Bar shows the application name, and the name of the active recipe or EasyView connection. The
Close, Minimize and Maximize button on the right-hand side of the title bar operate in the normal manner.

2 Menu Bar
The MKS RGA software is no different from other Windows programs; all the available functions are available
via the menu bar.

3 Views Windows
The Views windows are where the data acquired in the RGA software is displayed. All the windows for all the
recipes or connections are displayed here, but in the graphic just two are shown, a bar chart and a trend
associated with a single RGA connection.

4 Toolbars
The Toolbars appear as one or more rows of buttons below the menu bar and immediately above the recipe
list and views windows. Process Eye and EasyView have many buttons in common; however Process Eye
does have additional buttons that are not available or do not apply to EasyView. By default the buttons are
distributed between several toolbars. Each of the toolbars may be hidden by selecting View / Toolbars
from the menu bar and un-checking those you wish to hide. The default setting is visible for all toolbars.

5 Recipe List (Process Eye Professional only)

Process Eye is a recipe-driven RGA application. A recipe specifies in complete detail the actions that the RGA
is to take to acquire the data you need; it can manipulate the data, make ‘decisions’ based on the values
obtained and present the results in a flexible way. The Recipe List contains a list of all the
currently available recipes. To run a recipe, double click on the recipe title in the Recipe Names
list or select the recipe and click on the Run Selected Recipe button.

Process Eye Professional V5 –SP104008.100 August 2005 44

6a Status Windows (Process Eye Professional)
The Status window, as the name suggests, shows status information including instrument, filaments, events
and alarms. The Status Window is multi-page; in addition to the main page tab there will be additional tabs
for each recipe that is running.

Click on the tab for the page you wish to view. The tabs are named after the recipe to which they relate.
Click on the Recipe hotspot for recipe information and click on the Instrument hotspot for hardware
information.

6b Status Windows and Control Panel (EasyView)

The lower portion of the screen is given over to the Control Panel in EasyView. Like Process Eye the status
window is multi-page. The first page tab shows all the connected hardware. Subsequent tabbed pages
show the control panel for each running RGA. You use the features of the control panel to ‘drive’ the RGA.
You can acquire data, calibrate the analyzer, degas the ion source and so on.

Process Eye Professional V5 –SP104008.100 August 2005 45

4.3 Saving Data to Disk
If you are using Process Eye Professional, click the disk button on the toolbar at the top of the
screen. In EasyView click the large disk button in the control panel.

Note: The most common behaviour in Process Eye Professional is that the recipe defines the disk storing
attributes. In this ‘Getting Started’ example, however, we are using an interactive recipe in order to show
some similarities between the Process Eye Professional and the EasyView installations. Furthermore it will
often be the case that interactive control of the RGA in Process Eye Professional is best achieved by using
the built-in EasyView recipe described later in this manual.

Clicking the Interactive Disk Store button, whilst in an interactive recipe that is not already storing to disk,
will bring up the interactive store dialog. This is also explained in more detail in chapter 8.

In this dialog you can choose to store

from the current scan onwards, or from
any prior scan held in the active history
buffer.

If you have been acquiring data for a long

time, you may not be able to store all the
prior history.

If you choose to store from the buffered

history, you can choose to store just a
small part of it.

Clicking on Where to Store allows the user to specify a location for the stored data.

At any time, you can end the disk storage by clicking on the interactive store button again.

You can pause the disk store:

In Process Eye Professional click on the Disk store pause button.
In EasyView check the Pause check box.

To resume storing later:

In Process Eye Professional simply click the button again.
In EasyView un-check the Pause check box.
This will restart storing to disk to a new file.

Note: While the disk store is active, the scan is no longer interactive and the interactive scan controls will be
unavailable. When you pause or end the disk store the scan will become interactive again.

Process Eye Professional V5 –SP104008.100 August 2005 46

4.4 Adding Annotations
Time stamped annotations can be added to a swept measurement or a trend.
There are 2 ways to do this. The first is to click on the Add Annotation button.

In the dialog that appears, you can specify a time for the annotation to appear on the trend, and any text
you wish to add.

By default, the time of annotation will be the current time,

although you can select a new time, by using the Time and
Date list boxes.

Enter text into the Note text box; when your annotation is
complete, press the OK button.

The second way to add an annotation is to click on the Add Annotation at Selected Time button. This
method is always associated with a current trend view.

Select an active trend view. Then click the button.

The cursor changes to a pen; move the pen cursor along the
trend line to the point that you want to annotate. Clicking on
the trend here will bring up the annotation dialog, but now the
time will be set to the time at that position on the trend.

Each annotation added will be marked by a symbol along the top of the trend. If you move the
cursor over this symbol, the text will be displayed as a tool tip as shown.

If you have multiple trend views associated with the active

recipe or connection, they will all inherit the annotation. The
annotation will also appear on the barchart view when you scroll
to the scan in which the event occurred.

You can add as many annotations as required and when using Recall to review the data they will be
displayed in the same way.

Process Eye Professional V5 –SP104008.100 August 2005 47

Chapter 5 – Displaying the Acquired Data

Overview
Views are the graphs that display the RGA data. The software provides many features that allow you to
personalise and customize the way that this data is presented. EasyView and Process Eye Professional both
have the same presentation capabilities. However EasyView takes the simple approach that the way you set
up a particular view is the way that you will want it to look next time. Process Eye Professional lets you
define multiple views; the appropriate one for a particular task can be called up at any time.

Views come in two different types.

The first is a Swept Measurement View. This is a display of partial pressure versus mass.
There are two types of swept measurement view, the Bar chart shown below, where there is a single bar
shown per mass.

And the Analog view, where there are a number of bars per mass, giving a pseudo-analog view.

Process Eye Professional V5 –SP104008.100 August 2005 48

The alternative is the Trend view, where a variable versus time can be plotted.

In Process Eye Professional this type of view is particularly

flexible as the data plotted is not necessarily partial
pressures; any user variable can be plotted on trend.

Trend views can have multiple ‘panes’ but the maximum

number of individual channels they can display is limited
to 15.

You can display any number of separate trend views.

Process Eye Professional V5 –SP104008.100 August 2005 49

5.1 Editing the Barchart or Analog View Properties
A “live” view can be edited either by right clicking on the view itself, or by selecting the view and
clicking on the Properties button.

You change the properties on this page to customize your

view of barchart or analog measurement data. The next
section explains these properties in detail.

The software refers to analog and Barchart data as a ‘mass

scan’ because in both cases the RGA performs a continuous
sweep of equally spaced readings between a first mass and
a last mass.

EasyView ‘remembers’ the settings you choose in this

dialog so that they are automatically applied the next time
you acquire a continuous mass scan.

Process Eye Professional allows you to save several views

as ‘standard views’ that can be applied to your recipes
when you create them. In this way you can maintain a
standardised presentation of data that is relevant to the
task the recipe fulfills.

The above example shows the default properties that can be used to create the following default view.

In this view, all the masses acquired from

the first mass to the last mass are shown
on the X-axis along with the scan number.

The four-decade, logarithmic Y-axis,

displays the unit of pressure and the full-
scale pressure for the current data
acquisition setting.

Minor ticks are also displayed.

The following section outlines the various changes that can be made to views using the Properties for
Continuous Mass Scan View dialog. We will look at each function in turn.

5.1.1 X-Axis Properties

Checking the Use the data acquisition properties to set the X-axis properties button creates a view
with the X-axis properties governed by the measurement on which the view has been based.

For example, if the view was based on a Bar chart scan, measuring from mass 5 up to mass 45 then this
view will show mass 5 to mass 45 along the X-Axis.

Checking the Use the following bases the X-axis range on the values entered in the text boxes, with the
following limitations.
Although you can choose not to display masses that are being measured, you cannot choose to display
masses that are not being measured.

For example, you create a Bar chart measurement scanning from mass 5 to 45, you can base a view
displaying from mass 10 to 40, but not from mass 5 to 50. If this is attempted, the view will revert to
displaying the measurement’s range.

Process Eye Professional V5 –SP104008.100 August 2005 50

Minor Ticks
Displays minor ticks on the X-axis.

Show elapsed time in addition to scan number

Displays the elapsed time from the start of the recipe.

Show real time in addition to scan number

Displays the real time, governed by the PC clock.
Both the above options cannot be enabled at the same time.

Annotations
To edit the Annotations icon click on Annotations

Any annotation streams defined in the recipe will be listed, check the
display box to show the annotation on the view. To change the icon,
select one of the shapes from the list.

Click OK to return to the properties page

5.1.2 Initial Y-axis Properties

On a swept measurement, the Y-axis is always shown as pressure, the units of which are determined in
Process Eye preferences.

Use data acquisition properties to set Y-axis properties

Creates a view with the Y-axis properties governed by the measurement on which the view is based.

4- Or 5- decade log scale

Changes the Y-axis from a linear scale with its origin at zero, to a logarithmic scale with a minimum
dependant on the accuracy of the measurement. At the higher accuracies the software will display 5 decades
of pressure, while at lower accuracies it will display 4. The full scale pressure will be calculated automatically
based on the current electronic and detector gains.

Use the following explicit settings

Enables the maximum and minimum displayed pressures to be entered manually.
The display can be either linear or logarithmic determined by the check box.

Restrict these values to the maximum bounds of the acquired data

Causes the Y-axis maximum pressure setting, to be governed by the maximum pressure obtained from the
measurement associated with the view.
Note: You cannot display zero or negative values in logarithmic mode.

Grid
Displays a horizontal grid, aligned with the ticks of the Y-axis.

Minor Ticks
Displays minor ticks on the Y-axis.

5.1.3 Subsequent Y-Axis Auto-Ranging Strategy

If a view’s Y-axis limits are based on an “interactive” measurement, or the RGA has an inlet system, these
limits can be changed dynamically during the lifetime of the view.

Process Eye Professional V5 –SP104008.100 August 2005 51

Four options determine how the axis will react to future changes in the measurement conditions such as
using a new inlet or detector or electronic gain range for example.

Leave the Y-Axis unchanged leaves the Y-Axis settings unchanged when the measurement changes. The
settings will remain as you set them now.

Force the Y-Axis scale within the new recommended bounds reduces the maximum and/or increases
the minimum value so that the Y-scale does not overflow the new recommended bounds.

Expand the Y-Axis scale to include the new recommended bounds changes either the maximum or
the minimum Y-axis settings to incorporate the new settings.

Use the new recommended bounds changes the Y-Axis settings to match the new measurement
settings.

These options will become more obvious using the following example. Suppose you are currently acquiring
large peaks on a low electronic gain. The recommended bounds are from 1e-4 torr to 1e-8 torr. Now what
happens in the future when you switch to the high electronic gain range so that you can see the smaller
peaks? The new recommended bounds will be, say, 5e-7 torr to 5e-11 torr.

Option Y-axis Range Now Y-axis Range after future gain change to
recommended 5e-7 to 5e-11
1. Leave 1e-4 to 1e-8 1e-4 to 1e-8
2. Force within 1e-4 to 1e-8 5e-7 to 1e-8
3. Expand 1e-4 to 1e-8 1e-4 to 5e-11
4. Use 1e-4 to 1e-8 5e-7 to 5e-11

It may seem that the obvious choice is the fourth one. But the differences between the options become
clearer when you scroll back through the data that you obtained before the change. In some of the cases the
big peaks would be clipped at 5e-7; in others the early data would appear very noisy because it was
obtained at a lower gain.

Once the changes to the view settings are complete click on the Finish button to apply the changes or check
the Save Settings check box to bring up the Save View dialog described in 5.4.

Note: the save settings check box requires at least v5.21 of the software and is not available on EasyView
installations; nor is it available on Process Eye installations where the administrator has elected to install a
restricted user interface.

Process Eye Professional V5 –SP104008.100 August 2005 52

5.2 Editing the Trend View Properties
A trend view can be associated with any measurement. Along with the RGA data, it is also possible to display
signals from the analog / digital inputs and other user variables. The only limitation is that the X-axis is
always time.

Right mouse click on the trend view to bring up the

trend display properties dialog.

The first page is the channel setup page. It shows the

channels that are currently being displayed. You can
enable or disable channels by checking the box next to
the channel.

5.2.1 Editing a Trend Channel

You can edit a channel either by double clicking it, or by highlighting the channel and then clicking the edit
channel button.

This will bring up the Channel Properties dialog, which allows each channel to be set-up independently.

Type
The channel can be one of two types selected from the pull-down list.

A mass type channel, is a partial pressure measurement of a mass scanned by one of the measurements
in a recipe

Process Eye Professional V5 –SP104008.100 August 2005 53

A channel type channel is any channel other than the channel defined in the recipe. These channels are
user variables that can be defined either in the recipe wizard, or through script and are not necessarily
partial pressures.

The associated list of known gases relating to mass numbers is contained in the text file C:\Program
Files\Spectra\RGA Applications\Workstation\Common Gases.txt”. This may be edited or added to
in order to give an accurate description of the users system.

Editing a mass channel

If the channel type selected is Mass, there are a number of ways of editing the channel. One way is to select
one of the pre-defined channels in the selection table.

Clicking on one of the lines will set the mass value and channel name.
Alternatively, you can type in the value of the mass you wish to display in the Value text box.

Then type the name that you wish to appear on the trend key in the Channel name or alias text box.

Note: If you leave this box blank the channel name will be displayed as “Mass xx” where xx is the value
entered in the Value text box.

Trend views are not linked to any specific measurement; indeed in Process Eye Professional it is very
common to combine data from multiple sources onto a trend so that it is easy to see the interaction between
the process and the RGA. Often the name of the channel will uniquely identify the measurement; in this case
the <<auto>> option is the easiest to
use – the RGA software will
automatically find the single
measurement that has that named mass or channel. However, particularly with partial pressure data, it may
sometimes occur that you obtain the same mass on more than one measurement. You can specify for each
channel your preference for the measurement from which it should obtain its data.

For example, you have two Bar chart measurements, Bar chart 1 that is a mass 1 to 50 Faraday
measurement and Bar chart 2, which is a mass 1 to 100 multiplier measurement.

If the channel has a mass value of 4, the data would be taken from Barchart1 because that is the first
measurement that contains a mass with a value of 4. This will be true, even if the peak height on mass 4 is
so small that it is lost in the noise level and mass 4 in multiplier is a good stable peak.

If the value is mass 84 the data would be taken from Barchart2, even if the peak is so large it is off-scale.
This is because Barchart2 is the first measurement that contains mass 84.

Process Eye Professional V5 –SP104008.100 August 2005 54

Editing a user channel
If the channel type is set to Channel then the Value box is greyed out, as these channels are variables
defined by their names.

The channel will be selected based on the name in the Channel Name text box and the measurement
name in the Measurement Name text box.

Usually the measurement selection will be Auto because it would be very rare for your channel names to be
duplicated across multiple measurements (see the comments above in ‘editing a mass channel’).

Editing the channel display

To change the colour of a trend line, click on the Colour list box.

This will bring up a standard Windows colour selection dialog, where you can choose a new colour.

To change the thickness of the displayed line, move the slider on the Line Thickness control.

The Draw Stepped check box can be used when displaying information for a channel that has discrete
values.

Instead of each point on the trend being joined by a straight line, the points are joined only by horizontal
and vertical lines. The value of the reading is not changed and is not necessarily 0 or 1 (but is usually an
integer).

5.2.2 Adding a Trend Pane

You can create multiple trend panes that allow you to display a number of different Y-Axis linked to a
common time axis on the same trend window.

This is a 2-pane trend with channel 1

displayed on trend pane 1, with its own
measurement units and channel 2
displayed on trend pane 2 with different
measurement units.

You can, if you wish, display a channel

on both panes.

Process Eye Professional V5 –SP104008.100 August 2005 55

 On the Trend display pane and channel properties dialog,
click on the Add pane button to add a new pane.

The settings for each pane can be modified. Select the pane that you wish to edit from the Trend Pane Pull-
down list box

The two-pane view at the start of this section was created in the following way.

Channel 1 was enabled on trend pane 1

Channel 2 was enabled on trend pane 2

5.2.3 Configuring the Trend’s Y-Axis

Once the channels have been set, click on the Next button.
This will bring up the Y-axis dialog box.

Process Eye Professional V5 –SP104008.100 August 2005 56

Each trend pane can have a different Y-Axis setup. To set up each pane, select the pane you want to edit
from the trend Pane pull down list box.

Y-Axis Scale Properties

The scale can be set in a number of ways.

If you select the above option, the scale will be defined by the measurements that the displayed channels
use. For the Usermeasurement measurements, this is a scale between 100 and 1E-6. The check box will
change the scale between linear and log.

Checking the above will allow you to set the maximum and minimum limits on the Y-axis manually.

Enter the maximum value you want to display.

Enter the minimum value.

To display a Log scale, check the box.

Note: The software cannot display negative numbers or zero when set to Log scale.

If the Units of pressure check box is enabled, the axis will change scale if the units are changed in
preferences.

If the above option is checked, the scale will be limited by the maximum bounds of the measurements being
used. For example, if the only data to be displayed are mass channels from Barchart1, the limit of the
maximum value you can have will be the full-scale pressure on Barchart1.

With this option selected, the Y-axis pane does not have a scale as such. All enabled channels are given a
value of either zero or non-zero and are then plotted against their channel name.

This option is primarily useful for displaying digital data.

In this example, there are two digital input channels with
both channels configured to Draw stepped.

Tip: Put your digital channels in a pane above the partial

pressure data to see the relationship between the two.

Process Eye Professional V5 –SP104008.100 August 2005 57

Y-Axis General Properties

Enabling the grid check box will draw a horizontal grid on the trend.

Enabling the minor ticks check box will display minor ticks. If the grid is enabled you will also get grid lines
for the minor ticks.

Enter a label for the Y-axis in this text box.

If there is only one trend pane on the trend this box is set to 100% and unavailable

If there is more than one trend pane, you can set the proportion of the trend window that the particular
pane will occupy.

Y-Axis Auto-range Properties

If a view’s Y-axis limits are based on an
“interactive” measurement, or the RGA has an inlet
system, these limits can be changed during the
lifetime of the view.
Four options determine how the axis will react to
future changes in the measurement conditions such
as using a new inlet or detector or electronic gain range for example.

Leave the Y-Axis unchanged leaves the Y-Axis settings unchanged when the measurement changes. The
settings will remain as you set it now.

Force the Y-Axis scale within the new recommended bounds reduces the maximum and/or increases
the minimum value so that the Y-scale does not overflow the new recommended bounds.

Expand the Y-Axis scale to include the new recommended bounds changes either the maximum or
the minimum Y-axis settings to incorporate the new settings.

Use the new recommended bounds changes the Y-Axis settings to match the new measurement
settings.

These options will become more obvious using the following example. Suppose you are currently acquiring
large peaks on a low electronic gain. The recommended bounds are from 1e-4 torr to 1e-8 torr. Now what
happens in the future when you switch to the high electronic gain range so that you can see the smaller
peaks? The new recommended bounds will be, say, 5e-7 torr to 5e-11 torr.

Option Y-axis Range Now Y-axis Range after future gain change to
recommended 5e-7 to 5e-11
1. Leave 1e-4 to 1e-8 1e-4 to 1e-8
2. Force within 1e-4 to 1e-8 5e-7 to 1e-8
3. Expand 1e-4 to 1e-8 1e-4 to 5e-11
4. Use 1e-4 to 1e-8 5e-7 to 5e-11

Process Eye Professional V5 –SP104008.100 August 2005 58

It may seem that the obvious choice is the fourth one (which is the default). But the differences between the
options become clearer when you scroll back through the data that you obtained before the change. In some
of the cases the big peaks would be clipped at 5e-7; in others the early data would appear very noisy
because it was obtained at a lower gain.

5.2.4 Configuring the trend time axis

Click on Next to bring up the Time axis and legend
properties dialog.

Time axis properties

This option will display the time axis using real time as calculated by the PC clock.

This option will display the time axis as an elapsed time. The origin of the elapsed
time will depend on how the time origin is defined.

This is the offset from the elapsed time origin that the time axis
will start to display.

This is the amount of time that will be displayed on screen; in this

case the last 10 minutes of data will be displayed.

With Display Clock Time selected, the Clock Start feature is now available.

The time displayed will be the current time at the origin of the X-
axis. You can enter a new time and date for the X-axis origin,
however if you have Scroll Display enabled, the time origin will
be reset at the end on the next scan.

To change the date, click on the Clock Start pull down, the
Calendar dialog will appear. Select the required date from the
calendar pages.

Process Eye Professional V5 –SP104008.100 August 2005 59

 When checked the trend will automatically scroll to keep the latest data displayed. If not
checked you can manually scroll the display to see the data held at any point in the data
buffer.

When checked the time axis will display the number of days the trend has been running for
as well as the time.

When checked the time axis will display minor ticks.

To edit the Annotations icon click on Annotations

Any annotation streams defined in the recipe will be listed, check

the display box to show the annotation on the view. To change
the icon, select one of the shapes from the list.

Click OK to return to the Properties page

Elapsed time origin properties

Although you will commonly start acquiring RGA data as soon as the recipe starts this need not necessarily
be the case. Sometimes data acquisition is delayed and sometimes asynchronous data becomes available
long before the first RGA data scan. The elapsed time origin (t=0) can be set to be the time that the view is
created or the time that a particular measurement starts or a time of your choice. Data can still be plotted
prior to the origin, if it is available; the x-axis prior to elapsed time t=0 is shown in red.

With this option checked, the origin of the elapsed time is the time when the view was
created.

The elapsed time origin Time of my choice feature is also available.

You can set the origin to be any time you require; the elapsed time displayed becomes the time that has
elapsed from this point.

This option will set the elapsed start time origin to be the time that a particular measurement was created.

5.2.5 Key Legend properties

Select None to remove the key legend from the trend.

Otherwise select either Top or Side to position the key legend accordingly.

Once the changes to the view settings are complete click on the Finish button to apply the changes or check
the Save Settings check box to bring up the Save View dialog described in 5.4.

Note: the save settings check box is not available on EasyView installations; nor is it available on Process Eye
installations where the administrator has elected to install a restricted user interface.

Process Eye Professional V5 –SP104008.100 August 2005 60

5.3 Using the Toolbar Buttons to Change View Properties
You can change many visual properties without the need to use the properties dialogs simply by selecting
the view and clicking on a button in the toolbar.

Minor Ticks turns minor ticks on or off for the Y-axis.

Grid turns the grid on and off for the Y-axis.

Log/Lin changes between log and linear mode for the Y-axis.

Display Days switches on and off the Display Days function.

True/Elapsed Time switches between displaying the Real Time and the Elapsed Time.

X-Axis Minor Ticks turns minor ticks on and off for the X-axis.

X-Axis Scroll Bars turns scroll bars on and off for the X-axis.

For trend views:

Key Display makes the legend key visible or invisible.

Key Position moves the legend key either to the left of the trend or above the trend.

Process Eye Professional V5 –SP104008.100 August 2005 61

5.4 Saving the View Properties (Process Eye Professional Only)
You have already seen that EasyView maintains one set of Barchart and trend view properties which are
always applied automatically. Process Eye Professional allows you to create multiple ‘views’ and save them
to disk so that you can apply them at run-time or to recipes when you create the recipe.

To save the new settings, check the save settings box. On a trend view this is at the bottom of the Time
Axis page. On a swept measurement it is at the bottom of the property dialog.

Note: You need v 5.21 to do this for a swept

measurement.

This will then bring up the Save View.

Type in a name for the view; by default the file that will
store the properties is given the same name with a *.SI-v
extension.

If you want to give the file a name that is different from

the name of the view, click on the file Browse button and
manually rename the file.

If you want a caption to appear on the graph as a title,

type it in the Optional Screen Title text box.

If you want this view definition to be your default swept

measurement or trend view, check the Save this view
as the default view for its type checkbox. This is
explained further in the following section.
Note: this feature is not available if your administrator
installed the restricted user interface option.

Note: If you edit a currently existing view, and change the name in the Name by which this view will be
known in the list of views text box, the file name will not automatically be changed to match the list
name.

Unless you click on the File browse button and change the name of the file, you will overwrite the currently
existing view that you are editing and the original view will be lost.

Process Eye Professional V5 –SP104008.100 August 2005 62

5.5 Managing Views Using View Manager (Process Eye Professional only)
View Manager is Process Eye Professional’s central view management system. All stored views can be edited,
imported, or deleted through View Manager, regardless of their type or function. You can set one each of
your swept measurement and trend views to be the default for their type. You can also create a new view
for a specific purpose or recipe, although it is easier to create the view dynamically while acquiring data and
then save it for future use.

The View Manager feature can be started from the Recipe pull-down menu
and selecting Standard Views.

The other applications in the software suite (Recipe Wizard and Recall) have the
same menu. You can manage your views in any of these applications.

The Manage Views start page gives details of the current views
registered in Process Eye.

To create a new view, click the New button.

5.5.1 Creating a New View

A swept measurement view can only be associated with swept data acquisitions e.g. Analog or Bar chart
measurement. It cannot be associated with either a Peak Jump or a Leak Check measurement. A trend view
can be associated with any measurement or collection of measurements.

The Manage Views start page gives details of the current views
registered in Process Eye.

To create a new view, click the New button.

Process Eye Professional V5 –SP104008.100 August 2005 63

 The Create New View Dialog appears.

Select either Create New View on a Swept Measurement or

Create a new view on up to 15 … and then click the Next
button.

This will take you through the View Creation Wizards

described earlier. However, since you are ‘off-line’, Process
Eye does not fill in the current active scan information. You
define your own channel or mass span information and the
default measurements to use based on what you know of
the recipe that will be used at run-time.

On the save page the wizard defaults to giving the filename the same name as the view name, but you can
change this if you wish.

5.5.2 Editing a View in View Manager

Select the view that you wish to edit from the Manage Views dialog, and click the Edit button.

This will take you through the View Creation Wizards

described earlier. However, since you are defining a general
purpose view, Process Eye does not fill in the current active
scan information. You define your own

On the save page you can then either keep the same List Name and File Name, in which case the original
file will be overwritten, or you can choose to either change the List Name or the File Name. Changing the
names effectively creates a new view that was based on an existing one.

5.5.3 Importing a View

You can import a view from a different computer.

To import a view, select Import in the Manage Views

dialog.

The Import view dialog appears.

Process Eye Professional V5 –SP104008.100 August 2005 64

 Browse to the view definition file (*.SI-v) that you want to
import and click the Open button.

This will then take you through the View Creation

Wizards as described earlier, but with the various settings
already filled in with the settings from the imported file.

On the save page, you can either keep the same List Name
and File Name, in which case a copy of the definition file will
be generated in the Process Eye Professional\Views
directory,

Note: If the file is already in this directory, then it will be overwritten or you can choose to change either the
list name, or the file name.

5.5.4 Delete a View in View Manager

Select the view you wish to delete in the Manage Views dialog, and click the Delete button.

5.5.5 Setting a Particular View as the Default

One swept view and one trend view can be set as your
default for that type. The Manage Views dialog shows
which views, if any, are currently default. To select a view
as the default, simply highlight it and click Set As Default.

When you define which views a recipe uses you can select
that the recipe should use the default view. This will be the
view specified in the Manage Views dialog. If no view is
set as default, Process Eye will show a view with its own
default settings.

If you want to change the default view from one registered

view to another, simply highlight the new view that you
want as the default and click Set As Default. The existing default view will be un-set. If you want to stop
using one of your views as a default altogether (and revert to the built-in default view), select the view that
is currently the default view for that type and click the Set As Default button again.

Process Eye Professional V5 –SP104008.100 August 2005 65

Chapter 6 – Managing RGA Connections

6.1 Connection Information

The connections to Process Eye Professional or EasyView are usually configured in the RGA Device
Manager program; however you may also edit the connection settings from within the Process Eye main
program. If you have installed Process Eye Professional, the same dialogs are accessible from the same
menu item in Recipe Wizard.

From the Process Eye main window, select Connections

from the Instruments pull-down menu.

In EasyView the menu item is on the Recipe pull-down menu.

The Connections to Instrument Servers dialog appears.

Each of your RGA control units is connected to software that acts as a data ‘server’. On a network instrument
this software is part of the control unit. For a serial instrument the server software is a Windows application
that runs on your computer. The RGA application software is a ‘client’. It connects to these RGA
‘servers’ that act as a source of data. The connections dialog displays all the servers to which the
application is connected; when the connection is good these servers are denoted by this symbol.

If there is a problem with the connection, the server symbol is replaced with the following symbol.

Displayed beside the server symbol is the IP address of the server. If the RGA is connected to this computer
with a serial connection, it will show as having the localhost IP address of 127.0.0.1. even if your computer
has a real network address.

Process Eye Professional V5 –SP104008.100 August 2005 66

Displayed under the server symbol are details of all its associated instruments. If you have multiple serial
RS232/422 instruments connected to a computer they will all be listed beneath the common server. If you
have e-Vision or –IP instruments there can only ever be one instrument for that server.

If in RGA Device Manager you have set exclusive access to a particular control
unit, there will be a check in the box next to it.

This means when the Process Eye program is started and available instruments have been located, any
instruments with a check will be pre-connected and the instrument information will be displayed in the
Process Eye Status Panel.

Once the instrument has been pre-connected, it will become unavailable to any other connection.

If there is no check in the box next to the instrument, Process Eye will not pre-connect.
The instrument will be available to you and to any other interested connection. Only one
connection can control an RGA at one time, but the control unit will be ‘pooled’ between
multiple users.

You will also notice one other attribute in the small graphics above – the LM80 instrument is in use (indicated
by the small peak spectrum beside it), while LM92 is available for use.

If there is a problem with the connection to one of the instruments, the following symbol
will be displayed.

Further information about a connection can be seen if you click on one of the connections.

Clicking on the server will provide

details about that connection.

Clicking on the instrument will provide

details about that instrument.

6.2 Adding a Connection

To add a server connection click on the Add Connection button. The Add New Connection dialog
appears.

The list shows all the servers that are

on the network and all the serial
instruments connected to this computer
(on 127.0.0.1).

Check the box(es) beside all the servers

you wish to add and then click OK.

You may add an unlisted server by

network name or IP address. The
application will add this server to its list
of shared access connections, but the
application will not be able to connect to it at the present time.

Process Eye Professional V5 –SP104008.100 August 2005 67

Note: where a server has multiple instruments you only need to click one of its checkboxes to access all
instruments.

When you return to the Connections dialog you may optionally check the exclusive access checkbox next
to your new connection(s). You will get exclusive access the next time you run Process Eye. You will have
shared access during the current session.

6.3 Removing a Connection

To remove a connection, simply
highlight the connection that is no
longer required and click on the
Remove Connection button.

6.4 Refresh Connections

Although the list and its associated information is updated periodically automatically, you can force a
complete refresh of all the server information by clicking on the Refresh button

6.5 Export Connection Information

To save the connection information,

click on the Export button.

The Export a Server Information File dialog appears.

Choose a location and file name to save the file. By default the
suggested filename is thiscomputername_servers.dat.

This file can then be used on a PC without connections, to

simulate all the connections to this computer. This enables off-
line recipes to be written for the current installation.

You do not need to store information to save the current

configuration for use by the current PC; this happens
automatically. The file is not a back-up. Refer to the Hardware Setup chapter for information about backing
up control unit settings.

Process Eye Professional V5 –SP104008.100 August 2005 68

6.6 Exit Connection Dialog
To exit connections simply click on the Close button. If changes have been made to the pre-connection
status of any of the instruments and you want to activate the changes immediately, you must restart the
application (see section 6.2).

6.7 Hardware Information in the Status Pane (Process Eye Professional only)
The status window gives information on connected control units and any recipes that are running.
The window can be resized and can be docked or float anywhere on the screen. By default, it is docked at
the bottom of the Process Eye screen.

6.7.1 No Instruments Connected Window

If there are no instruments connected, or if the system is not set up for exclusive access to any instruments,
then the page will appear as above.

Clicking the Click to make Connection link takes you to the Connections dialog described above.

6.7.2 General Information Window

If there is an instrument connected, the instrument details will appear on the page.
The blue information area of the window is always visible.

The white information area changes to reflect the currently selected mode.
It also displays details on the currently selected instrument, filament and multiplier status.

Select Filament selects which of the two filaments to use. Click on the arrow. The number
indicates the active filament. Your selection becomes the new default each time the control unit is
powered up.

Filament On/Off
Click to switch the filaments on or off. When the filament is on, it is displayed red; when off, blue.

6.7.3 Digital IO Window

Clicking the Digital IO button changes the information panel, to that of the digital IO port.

Process Eye Professional V5 –SP104008.100 August 2005 69

The digital ports consist of 2 ports of 8 lines. In the above example port A is configured as 8 outputs and
port B is configured as 8 inputs. However the inputs and outputs can be configured in any combination
required. Inputs are shown as circles; outputs are shown as squares.

A white box signifies the bit is low, a blue box signifies that the bit is high. A blue circle signifies a high input
and a white circle signifies a low input.

6.7.4 Remote Vacuum Controller (RVC) Window

If your system is configured to have an RVC, then the Digital IO button will be replaced by an RVC button.

Clicking on this button will display

the RVC status. Here you can
switch the turbo, heater, filament
valve(s) and valve mode.

6.7.5 Cirrus Window

If you are using Process Eye with Cirrus, the Digital IO button is replaced by a Cirrus button. Clicking this
button displays the Cirrus status.

You can control the Cirrus pumps

and heaters directly from this
window. If the Cirrus has a
multi-valve inlet, you can select
the active inlet from the drop-
down list.

The Pump indicator is red when the pumps are off, amber when the pumps are starting up, and green when
the pumps are fully operational and the turbo is at speed. Clicking the indicator will toggle the status.

The main Heater selection box allows the user to select three states for the chamber heater - Off, Warm,
and Bake.

When the capillary heater is on the indicator will turn from red to green, clicking the indicator will toggle
the status.

For more information on the Cirrus see the Cirrus manual.

Process Eye Professional V5 –SP104008.100 August 2005 70

6.8 Hardware Information and Connections in the Status Pane (EasyView
only)
EasyView shows much of the same information as Process Eye Professional in its control panel at the bottom
of the screen. There is a Cirrus button and an RVC button if this hardware is installed. Clicking the relevant
button shows the same information and offers the same controlling capabilities as Process Eye Professional.

The Main tab at the bottom left of the control panel shows the connection and Ready states of all the
available control units.

The Edit Connections button leads to the connections dialog already described. The Refresh List button
updates the list but does not refresh all the server information. To do that you must click Edit Connections
and then click Refresh in the Connections Dialog.

If the instrument can be used by EasyView, the status is shown as Ready; if not the status should give an
indication of why the instrument cannot be used.

If you do not already have a tab at the bottom of the control panel for the instrument that you want to use,
click the Connect button or double-click the row in the list that applies.

Each connected control unit will have its own tab at the bottom of the control panel. Click on the relevant
tab to see the information pane.

Process Eye Professional V5 –SP104008.100 August 2005 71

Chapter 7 – Using Process Eye Professional

7.1 Recipes in Process Eye Professional

Recipes are fundamental to Process Eye Professional. The software does nothing until you give it a recipe to
run. Indeed, rather than thinking of Process Eye Professional as RGA software it is more accurate to describe
it as software to run recipes. These recipes are fully fledged programs written in a version of Microsoft Visual
Basic that is used by millions of people worldwide every day because it is found on, or used to generate,
more than half of the active pages displayed on the World Wide Web.

Process Eye Professional is aimed at users in a production or process environment where it is essential that
the RGA does its work in a consistent way each time it is used. Although there may be times when the RGA
expert needs to run the RGA interactively, the main purpose is to perform repetitive tasks so that RGA data
can be used to diagnose inconsistent output from a process.

A recipe does not have to make use of an RGA. One of the supplied recipes demonstrates this point.
However the most likely scenario is that you will run recipes that do use your RGA to acquire and display
data.

Since recipes are effectively small programs in their own right, they can do almost anything that your
computer can do. They can acquire data from other sensors; they can communicate with other applications
or with your Factory Management system; they can manipulate the data that they acquire and make
decisions based on that derived data or display the derived data in a variety of ways.

Fortunately you do not have to be a programmer to create these recipes because Process Eye Professional
comes with the Recipe Wizard application that will write the recipe for you in response to your input into a
sequence of wizard-style queries. If you are a VB programmer you can extend these wizard generated
recipes further. Process Eye Professional will even run compiled recipes written in VB or Visual C++,
although a description of the techniques to do this is beyond the scope of this manual.

Process Eye Professional uses the concepts of a ‘scan’ made up of one or more ‘measurements’.
Measurements are typically analog, barchart, peak jump or leak check acquisitions. To these you can add as
many ‘user measurements’ as you like to contain your derived data; user measurements can contain as
many individual ‘channels’ of data as you wish. Process Eye will gather one complete set of readings from
the RGA and then call the recipe to calculate the values for all the channels in the user measurement(s). This
completes one ‘scan’ and the process repeats.

Recipes are totally event-driven. The completion of a scan is one such event. Other data such as electrical
analog or digital inputs is almost always ‘asynchronous’ to the scan. So this data also gives rise to change
events and the data arriving from these sources can be stored separately from the scan data.

The built-in functionality of the recipe software is contained within the Process Eye Object Model. In addition
to many properties and methods associated with the scan, measurement and reading objects the model
supports the ability to control the display of windows and the user interface.

The CD-ROM contains several useful recipes to get you started; this manual assumes that you have installed
these and that you will run them as you read through this chapter. Please be aware that the author of a
recipe has the ability to set properties that control whether a user can launch the recipe or can close it; the
recipe may allow the user to interact with the data acquisition or not or to modify the configuration of the
RGA. The administrator of your system may even have elected to install a restricted user interface; in this
case you will not even have access to recipes and this chapter will not be relevant to you. Obviously, if this is
the case, you will have been supplied with a set of recipes that control the RGA automatically.

Process Eye Professional V5 –SP104008.100 August 2005 72

7.2 Launching a Process Eye Recipe
The currently available recipes are shown in the Recipe List.

To run a recipe do one of

Double-click the entry in the Recipe List

Highlight the entry and choose Recipe | Run from the menu, or click the
Run Recipe button on the Toolbar.

Right click the entry and choose the Run menu option.

7.3 Closing a Process Eye Recipe

The simplest way to close a recipe is to select its tab in the Status Pane and then click its close button at
the top right hand corner. This button may be disabled if the author has written the recipe to disallow
manual closure of the recipe.
(Presumably an event has been chosen to
close the recipe automatically.)

You can also select the recipe and

then click the Close button in the
main toolbar.

The start-up recipe associated with the

Main tab can never be closed.

Process Eye Professional V5 –SP104008.100 August 2005 73

7.4 Creating a New Recipe
Either select Recipe | New from the main menu bar or right click on the Recipe List and choose New
from the pop up menu. This will launch the Recipe Wizard.

If you do not want to see this introductory page in

future, check the box.

Recipe Wizard has full on-line context sensitive help

that you can access either by clicking the Help button
or by pressing the F1 function key. Each page of the
wizard has its own help information.

Here is a selection of the choices offered on the following pages:

• Whether to acquire data from an RGA; whether the recipe is for a particular RGA or whether the
choice can be left until run-time.
• The RGA data to be acquired.
• The data to be derived from the RGA data.
• Additional events that trigger actions
• How to display the data acquired
• Whether to save the data to disk
• Alarm criteria and actions.

The full features of Recipe Wizard are described in an associated manual. Having created the recipe you run
it as described in section 7.2 above. Advanced users can display the recipe script and extend the functionality
by writing VB code in any of the event placeholders generated by the wizard. This capability is not described
further in this manual.

7.5 Editing an Existing Recipe

Select the recipe to be edited in the Recipe List window, right click and choose Edit from the pop up menu,
or choose the Recipe | Edit selection from the main menu bar. This will re-run the wizard. Make the
changes you require and when you click on the Finish button the edited recipe will be saved.

Process Eye Professional V5 –SP104008.100 August 2005 74

7.6 Recipe Information in the Status Pane
Each active recipe will have its own tab and its own information pane within the Status Window. On the
blue area to the left there are two links – one to the Recipe Status information and the other to the
Instrument information.

7.6.1 Recipe Information View in the Status Window

The information shown here is

the output from the recipe event
log. The recipe author can output
messages to this window.

7.6.2 Instrument Status View in the Status Window

Click on the instrument name in the blue screen area to switch to the Instrument Status View. Depending on
the configuration of the hardware
you will have tabs across the top
for General, Ion Source, Tuning,
Digital I/O, RVC and Cirrus. Click
on the appropriate tab for the
information that you want to
view.

The General tab has interactive controls that allow you to switch the filament on or off and to choose which
of the two available filaments to use.

7.6.3 Ion Source Settings View in the Status Window

Click on the Ion Source tab to reveal the ion source settings for the recipe’s control unit. If your recipe does
not allow tuning, these pages will be for information only. However, if your recipe does allow tuning, you will
be able to change the ion source settings on this page.

Note: These controls are

enabled only if the measurement
mode is analog and if the recipe
author has allowed tuning.

The ion source configuration for the current recipe is shown in green text while the settings displayed relate
to the configuration highlighted in yellow. In the above example the sliders and text boxes show the settings
for the active configuration, Standard Electron Energy.

Enter a number in the text boxes for the four parameters, or use the sliders to change the values. You can
change the settings for any of the parameters in any of the configurations – but remember that you will only
see the effect on the data in the configuration associated with the green text because that is the
configuration being used to acquire the data.

Process Eye Professional V5 –SP104008.100 August 2005 75

7.6.4 Tuning View in the Status Window
Click on the Tuning tab to reveal the alignment settings for the recipe’s control unit. If your recipe does not
allow tuning, these pages will be for information only. However, if your recipe does allow tuning, you will be
able to change alignment and resolution on this page.

Exactly the same comments apply to the tuning parameters in the Tuning View. In the example shown above
the settings shown are again applicable to the active Standard Electron Energy configuration.

Either enter a number in the text boxes for the four parameters or use the sliders to change the values.

If you wish to use the current tuning parameters on all of the ion source configurations, you can simply click
on the Copy to all button.
If you change your mind, clicking on the Undo Copy will reset the parameters to their previous values.
This undo option is only available whilst this window is open. If the active view is changed, the values will be
permanently written.

Note: You will often use the EasyView recipe to adjust the ion source, alignment and resolution because it
provides an easy to use interactive environment in which to work. Please read the additional information on
tuning in the next chapter.

7.6.5 The Status Window for the Start-up Recipe

The start-up recipe associated with the Main tab behaves like the status window for any other recipe except
for two differences; the instrument information shows all the instruments connected to the application and
the start-up recipe does not have a recipe status view.

The next chapter is entitled ‘Using EasyView’. As a Process Eye Professional user you should still read the
chapter because you have the functionality of EasyView accessible to you as an EasyView recipe.

Process Eye Professional V5 –SP104008.100 August 2005 76

Chapter 8 – Using EasyView

Overview
EasyView is a special application that provides interactive control of the RGA. All standard RGA modes of
operation are available, in addition to diagnostics, degas and calibration mode. The previous chapters have
described how to manage your instrument(s) and how they will be displayed in the Main tab of the control
panel. When the application starts it automatically creates a connection to all your instruments. Each one has
its own tabbed page.

All scanning modes are fully interactive allowing changes to be made to all scanning parameters. There is
also a disk store function allowing all data to be stored to disk, for review using the Recall program.

If you installed Process Eye Professional, the functionality of EasyView is available to you as a recipe. You do
not need to install it. It will always appear in the recipe list window. If you want to access the features
described in this chapter, double click the recipe item once for each control unit that you want to connect to.
If there is more than one available instrument, you will select the one to use for the current instance by
double clicking it. You will not be able to connect to any instrument that is already running a recipe.

Important Note: Several of the MKS RGA control units maintain a set of six separate ion source and tuning
parameters. In keeping with its simpler approach to hardware control EasyView maintains one set of ion
source and tuning parameters for each control unit that apply throughout the application. In order to
maintain compatibility between EasyView and Process Eye Professional, the EasyView product sets all six of
these sets of values to be the same.

Process Eye Professional maintains the six named combinations of ion source and tuning parameters
individually, so that you can change the behaviour of the control unit by switching from one set of settings to
another. If you are using Process Eye Professional to run the EasyView recipe, you will have an extra drop-
down list box in the Mode toolbar described below. You use this to select the active configuration.

Process Eye Professional V5 –SP104008.100 August 2005 77

8.1 EasyView Toolbars
There are two EasyView toolbars; the Mode Toolbar is the horizontal toolbar across the top of the EasyView
status page.

Analog Mode button starts (or stops if already running) the Analog mode.

Barchart Mode button starts (or stops if already running) the Barchart mode.

Leak check Mode button starts (or stops if already running) the leak check mode.

Peak Jump Mode button starts (or stops if already running) the peak jump mode.

Disk Store starts (or stops if already storing to disk) storing data to disk

Filament Select chooses the current active filament. Clicking on one or other of the arrows
toggles the active filament between filament 1 and filament 2

Filament Status shows the current status of the filament. Blue represents a filament that is off.

Red represents a filament that is on. Clicking the icon will toggle the filament between off and on.

Diagnostics runs the diagnostic program on display the diagnostic report on the screen.

The Page Selection toolbar is the vertical toolbar along the side of the status page; it has the following
buttons.

Information returns the status window display to the general information page.

Tuning opens the tuning page in the status window. This page has the controls that enable you to
adjust the tuning of the RGA (peak alignment and resolution).

Calibration opens the calibration settings page in the status window. You can calibrate your RGA
based on the settings you select on this page.

Peak Jump Settings is only visible when EasyView is in Peak Jump mode. Clicking on this button
brings up the Peak Jump settings page in the status window.

The Cirrus button is only visible when the control unit is associated with a Cirrus benchtop
analytical RGA system. Clicking this button brings up the Cirrus information and control page.

The Degas button opens the Degas Settings page. You can degas the ion source of selected MKS
RGA’s based on the settings you enter on this page.

The RVC button opens the RVC settings and status page. You use this page to manage the vacuum
hardware when fitted.

If you are using Process Eye Professional to run the EasyView recipe, you will additionally have an ion source
configuration drop-down list box. Use this to select the active ion source configuration for the RGA.

Process Eye Professional V5 –SP104008.100 August 2005 78

8.2 Analog Mode

The above screen is displayed by clicking the Analog Mode button in the Mode toolbar and selecting the
Tuning button in the Page Selection toolbar.

The Analog view is displayed and the interactive analog control toolbar will appear in the status window.

Use this toolbar to change the scan parameters, each of the functions are explained below.

Start Mass

To change the start mass of the scan, either enter a number directly into the box, or click on the arrows to
increase or decrease the mass number. Note that the first mass cannot be less than 1 and that the first mass
plus the mass span, cannot exceed the maximum mass allowed by the control unit.

Mass Span

To change the mass span of the scan, either enter a number directly into the box, or click on the arrows to
increase or decrease the mass span.
Note that the first mass plus the mass span cannot exceed the maximum mass allowed by the control unit.

Accuracy

Scan accuracy determines the amount of averaging carried out for each reading.
A high accuracy number provides a clean scan but increases scan time.
The accuracy ranges available are from 0 to 8.

Points per peak

The number of measurements each full mass is divided into 8, 16 or 32.

The higher the number of points-per-peak selected, the better the representation of peak shape. However,
scan time and the amount of data generated will increase. If the data is to be imported into Excel for
instance, choose a lower value.

Process Eye Professional V5 –SP104008.100 August 2005 79

 Electronic Gain

The electronic gain of the pre-amplifier can be changed by selecting one of the values from the drop down
list. The lowest electronic gain appears first in the list. The pressure indicates the maximum value that can
be measured using that range. The higher the gain selected, the smaller the partial pressure that can be
measured, this may cause peaks of a higher partial pressure to saturate.

Detector

The detector type used for the scan can be changed.

Depending on the type of instrument, the options are Faraday, Multiplier 1, Multiplier 2 and Multiplier 3.
Multiplier 1, 2 and 3 refer to the same physical detector, but using three separate calibration values that
provide successively greater amplification of the ion current.

Process Eye Professional V5 –SP104008.100 August 2005 80

8.3 Barchart Mode

The Barchart view is displayed and the interactive Barchart control toolbar will appear in the status window.

Use this toolbar to change the scan parameters, each of the functions are explained below.

Start Mass

To change the start mass of the scan, either enter a number directly into the box, or click on the arrows to
increase or decrease the mass number. Note that the first mass cannot be less than 1 and that the first mass
plus the mass span, cannot exceed the maximum mass allowed by the control unit.

Mass Span

To change the mass span of the scan, either enter a number directly into the box, or click on the arrows to
increase or decrease the mass span.
Note that the first mass plus the mass span cannot exceed the maximum mass allowed by the control unit.

Scan Mode

The scan mode is the method used to report the peak height.
The options are - Peak Centre, Peak Max or Peak Average.

Accuracy

Scan accuracy determines the amount of averaging carried out for each reading. A high accuracy number
provides a clean scan but increases scan time. The accuracy ranges available are from 0 to 8.

Electronic Gain

The electronic gain of the pre-amplifier can be changed by selecting one of the values from the drop down
list. The lowest electronic gain appears first in the list. The pressure indicates the maximum value that can
be measured using that range. The higher the gain selected, the smaller the partial pressure that can be
measured, this may cause peaks of a higher partial pressure to saturate.

Process Eye Professional V5 –SP104008.100 August 2005 81

 Detector

The detector type used for the scan can be changed.

Depending on the type of instrument, the options are Faraday, Multiplier 1, Multiplier 2 and Multiplier 3.
Multiplier 1, 2 and 3 refer to the same physical detector, but using three separate calibration values that
provide successively greater amplification of the ion current.

Add Trend

Click this button to add or remove a trend view in addition to the Barchart view. This tend can be edited in
the same way as any normal trend view.

Process Eye Professional V5 –SP104008.100 August 2005 82

8.4 Leak Check Mode

The Leak Check view is loaded and the interactive Leak Check control toolbar appears in the status window.

Use this toolbar to change the scan parameters, each of the functions are explained below.

Probe Mass

To change the probe mass of the scan, either enter a number directly into the box, or click on the arrows to
increase or decrease the mass number. In contrast to the other modes that require whole number masses,
leak check mode permits fractional masses, but you cannot enter a mass that exceeds the maximum mass
allowed by the control unit.

Accuracy

Scan accuracy determines the sampling amount carried out on each reading. A high accuracy number
provides a clean scan but increases scan time. The accuracy ranges available are from 0 to 8.

Electronic Gain

The electronic gain of the pre-amplifier can be changed by selecting one of the values from the drop down
list. The lowest electronic gain appears first in the list. The pressure indicates the maximum value that can
be measured using that range. The higher the gain selected, the smaller the partial pressure that can be
measured, this may cause peaks of a higher partial pressure to saturate.

Detector

The detector type used for the scan can be changed.

Depending on the type of instrument, the options are Faraday, Multiplier 1, Multiplier 2 and Multiplier 3.
Multiplier 1, 2 and 3 refer to the same physical detector, but using three separate calibration values that
provide successively greater amplification of the ion current.

Process Eye Professional V5 –SP104008.100 August 2005 83

 Audio Not support on certain sensor configurations.
Switches the audio tone on or off.
The tone changes in frequency as the measured peak height changes. This is a useful feature if you are
unable to see your monitor while leak checking.

Re-zero

The control unit takes a zero measurement before it starts returning the values for the partial pressure of the
probe mass. You click this button to force the control unit to take a new zero measurement.

Process Eye Professional V5 –SP104008.100 August 2005 84

8.5 Peak Jump Mode

In Peak Jump mode an interactive Peak Jump control toolbar appears in the status window and the data is
displayed in a trend view window.

Use this toolbar to change the scan parameters, each of the functions are explained below.

Scan Mode

The scan mode is the method used to report the peak height. The options are - Peak Centre, Peak Max or
Peak Average.

Accuracy

Scan accuracy determines the sampling amount carried out on each reading. A high accuracy number
provides a clean scan but increases scan time. The accuracy ranges available are from 0 to 8
.

Peak Jump Settings

Use this button to open the Peak Jump settings window shown below.

Settings for each of the 15 channels can be edited using this toolbar.

Click on the channels tab to edit the settings for that particular channel.

Check the box to enable the channel.

In the above example only channels 1 to 7 are enabled, channels 8 to 15 are disabled.

Process Eye Professional V5 –SP104008.100 August 2005 85

 Scan Mass

Set the particular channels scan mass. Note that the mass cannot be less than 1 and cannot exceed the
maximum mass allowed by the control unit.

Electronic Gain

The electronic gain of the pre-amplifier can be changed by selecting one of the values from the drop down
list. The lowest electronic gain appears first in the list. The pressure indicates the maximum value that can
be measured using that range. The higher the gain selected, the smaller the partial pressure that can be
measured, this may cause peaks of a higher partial pressure to saturate.

Detector

The detector type used for the scan can be changed.

Depending on the type of instrument, the options are Faraday, Multiplier 1, Multiplier 2 and Multiplier 3.
Multiplier 1, 2 and 3 refer to the same physical detector, but using three separate calibration values that
provide successively greater amplification of the ion current.

Line Thickness

The thickness of the plotted line can be changed to aid visibility

Colour

The colour of the plotted line can also be changed.

Select a colour then click OK to apply it to the channel.

Update Scan

Changes made to the channels properties are not immediately made to the scan. When all changes required
have been made, click Update Scan. The new settings will then be applied.

It will be apparent that the accuracy and scan mode apply to all the scan channels. However, individual
channels can use different detectors or electronic gain settings. If you use more than one value for these
properties, EasyView groups channels that have common settings together. Otherwise readings are taken in
the same order as the channels are displayed. You do not have to have the mass values in ascending order.
Indeed sometimes it is an advantage not to do so. Peak jump mode is a fast acquisition mode. The RGA may
not have time to recover if adjacent channels require it to move from a very high partial pressure to a very
low one. Data quality may be improved by thinking carefully about the mass sequence. Passing over a large
reading can be as harmful to data quality as taking a reading at that mass. You may improve data quality by
adding one or more ‘throw-away’ channels after the RGA has scanned over a large peak.

Process Eye Professional V5 –SP104008.100 August 2005 86

8.6 Disk Store
Disk Store is available in any of the EasyView scan modes and can be accessed by clicking the
button shown.

What to store options:

From now onwards starts storing when you click

OK.

From buffered scan allows you to select a prior

scan number or time so you can store data that
EasyView is holding in its history buffer. If you enter a
scan number, the time will be adjusted to match. If
you enter a time, the corresponding scan number will
be shown.

Note: The buffer is reset if any changes to the

current scan are made; otherwise somewhere between 500 and 1000 prior scans are stored in the buffer.

Likewise you can select to continue storing indefinitely or to finish at one of the scans in the history buffer.
You cannot set a particular future scan or time.

Where to store options:

Folder: enter the path, or browse to the folder where
the scans are to be stored. The default path is:...
\Data\EasyView ControlUnitName\

Name
Enter a name for the saved data file, by default this is
“data” but it can be anything you choose.

The file name can optionally be amended with other information:

Just use the folder/name specified creates (in the example shown) the file “data.SI-d”. An existing file
of the same name would be overwritten.

Append date/time information to name adds date and time information to the file and would create the
file “DataYYYYMMDDHHmmSS.SI-d” where YYYY is the current year, MM is the current month, DD is the
current day, HH is the current hour, mm is the current minute and SS is the current second.

Append incrementing number to the name adds the next available sequential number to the name and
would first create “Data000001.SI-d”; the next would be “Data000002.SI-d” and so on, thus creating a new
file each time data is saved.

While storing to disk, the Disk Store toolbar will be visible in the status window.

Notice that the disk store icon is no longer available and the path to the disk store file is displayed.

Process Eye Professional V5 –SP104008.100 August 2005 87

Checking the Allow Changes box, pauses the disk store and re-enables the scan toolbar.

You can then change the scan properties, un-check the Allow Changes option and continue with the Disk
Store without having to run through the Start Disk Storage dialog.

Note: The name of the file will still change. A given data file can only store data for one set of acquisition
conditions.

Process Eye Professional V5 –SP104008.100 August 2005 88

8.7 EasyView Diagnostics
Diagnostics mode is only available if there is no scan mode currently selected. If diagnostics is
unavailable then the selection is greyed out.

Running diagnostics in EasyView produces the following

report:

Note that there is just one set of ion source and tuning
settings that is used throughout the application. This same
set of values is applied to all six of the settings in the control
unit.

Running diagnostics on a Process Eye Professional

installation produces the following report:

Note that the six individual (and different) source and

tuning settings are shown.

The report contains information about the control unit configuration, source settings and mass
alignment/resolution settings as well as power supply levels.

In order to test the multiplier, the filament

needs to be switched on. If you run
diagnostics without switching the filament
on the following dialog appears.

Cancel to exit without running diagnostics

No to run diagnostics with the filament off, in which case the multiplier voltage will not be tested.
Yes to switch the filament on and then run diagnostics. If you choose this option, be sure that the vacuum
level is such that it is safe to switch the filament on.

Process Eye Professional V5 –SP104008.100 August 2005 89

8.8 EasyView Tuning
Note: Tuning parameters can only be changed whilst in the analog mode. In all other modes the tuning
information can only be viewed.

Note: If your control unit is an e-Vision or e-Vision Plus, you will not be able to change the ion source
settings.

The tuning information page consists of two parts. The first is the mass alignment and resolution controls,
the second the ion source parameters.

The mass alignment controls control the position of the mass peaks in relation to the mass scale. There are
two controls for the alignment.

The low mass control affects all masses by the same amount. Moving to slider to the right causes the peaks
to move to the right and causes the alignment value to increase. Moving the slider to the left causes the
peaks to move to the left and the alignment number to decrease.

The high mass control affects masses proportional to how far up the mass scale they are. Moving mass 1 by
0.1 amu using the high mass control will cause mass 100 to move by 1 amu for example.

The resolution controls control the peak width. As you increase the resolution the peak will get narrower but
will also become smaller. Reducing the resolution will make the peaks bigger but can lead to interference
between adjacent peaks. For standard instruments the resolution is set so the peak width at 5% (10% for
HPQ2 units) of the max peak height is 1 amu.

This peak is aligned at mass X

The resolution is set to 1 amu at 5% of the maximum peak height

All instruments have the mass alignment and resolution set before leaving the factory. A copy of the tuning
settings is always included with the documentation. Only small changes to the alignment and resolution
should ever be necessary to account for small changes in temperature between the factory and place of
operation. If major changes are made to the settings so that peaks are no longer visible, please re-enter the
factory supplied settings to try and recover the peaks.

Process Eye Professional V5 –SP104008.100 August 2005 90

The ion source parameters are by default set to the optimum parameters for the type of ion source fitted. If
required for specific applications, these parameters can be changed. There are four parameters to change
and they have the following functions.

Emission current is the current of thermally emitted electrons that flows between the filament and the
source plate. The emission current is regulated by the temperature of the filament and hence by the actual
current passing through the filament.
Up to a point higher emission current gives higher peak heights, however higher emission currents mean
higher filament temperatures and shorter filament life. Nominal emission current is 1 mA but this should be
reduced if running at high pressure or at low electron energy.

Electron Energy is the accelerating voltage between the filament and the ion source. It is therefore the
energy that the electrons have in the ion source. The standard electron energy is 70eV however for
particular applications this may be changed.
For example reducing the energy below 40eV will prevent Ar++ ions being formed. This will prevent peaks at
mass 18 and 20 due to the doubly charged argon atoms having masses of 36 and 40.

Ion energy is the voltage of the ion source and hence the starting energy of the ions. Changing the ion
energy will affect the ion optics of the source and would not normally be changed.

The Extract voltage is the voltage on the extract plate and the repeller in the ion source. This voltage again
affects the ion optics of the source and would not normally be changed.

Process Eye Professional V5 –SP104008.100 August 2005 91

8.9 EasyView Calibration - Faraday
Click on the Calibration button in the Select Page toolbar to bring up the calibration setup
page. If it is not already selected, click on the Faraday tab.

Calibration can only be performed if the instrument is not in one of the scanning modes.

The date of the last calibration

using these settings is
displayed at the bottom of the
window. In this case this is the
first time the calibration has
been run with these settings

Pick a mass to calibrate against and enter a known partial pressure for that mass.

Start the calibration by clicking on Start. This will launch the Calibration Wizard. If the filaments are not
currently switched on, you will be prompted to do so.

The calibration routine will then measure the zero, the peak maximum value and the peak center value of
the mass chosen and then perform a stability check of 10 readings.

Click Next to view the results of the calibration.

To exit without changing the calibration click Cancel.

To apply the default calibration click Default.

To use the calibration just performed click Apply.

The calibration is now complete click on Finish to exit.

Process Eye Professional V5 –SP104008.100 August 2005 92

The date of the calibration and sensitivity value will then be displayed at the bottom of the EasyView
window.

Details of all calibrations are logged in the application log file at one of the following locations
\..\Process Eye\Logs\Process.xml or
\..\Process Eye\Logs\Process.log or
\..\EasyView\Logs\Process.xml or
\..\EasyView\Logs\Process.log

When the calibration runs the software checks the stability of the partial pressure by taking ten separate
readings and calculation the standard deviation (sigma) of the sample.

If the value of 3 x sigma as a percentage of the first reading taken is:

Less than 1% the stability is excellent; otherwise if it is

Less than 3% the stability is good; otherwise if it is
Less than 10% the stability is acceptable;
otherwise the stability is poor.

Where the calibration is performed at the peak centre, the algorithm reports any misalignment of the peak in
increments of 1/32 of an a.m.u.

Process Eye Professional V5 –SP104008.100 August 2005 93

8.10 EasyView Calibration - Multiplier
Click on the Multiplier tab on the calibration page.

Select the multiplier setting to be calibrated from the drop down list, the mass to calibrate against and the
multiplier gain required. By convention you typically calibrate Multiplier1 to have a gain between 30 and 100,
Multiplier2 to have a gain between 100 and 1000 and Multiplier3 to have a gain greater than 1000. The
multiplier will be calibrated at the mass chosen, so that the pressure reported in faraday and multiplier at
this mass will be the same.

If you are using Process Eye Professional, you will have an additional option to apply the same gain and
detector voltage to all the ion source configurations.

Click Start to begin the calibration.

The calibration will perform a zero, measure the peak height in faraday, adjust the multiplier voltage so the
peak height in multiplier with the gain specified matches and then check the stability.

When the calibration finishes, click Next.

Details of the previous and current calibration will be

displayed, click Apply to apply the current calibration.

The date and sensitivity of the current calibration will be displayed at the bottom of the EasyView window.

Process Eye Professional V5 –SP104008.100 August 2005 94

Details of all calibrations are logged in the application log file at one of the following locations
\..\Process Eye\Logs\Process.xml or
\..\Process Eye\Logs\Process.log or
\..\EasyView\Logs\Process.xml or
\..\EasyView\Logs\Process.log

Process Eye Professional V5 –SP104008.100 August 2005 95

8.11 Degas
Note: Not all MKS control units support the degas capability.

Click the Degas button on the Page Selection toolbar to reveal the ion source degas settings.

When EasyView degasses an ion source it ramps up to full power over a user defined period of time. It then
maintains that power for a further period. When degas is complete it resets the ion source conditions to
‘normal’ and waits for a period of time during which the temperature of the source can stabilize.

You enter the values that determine this power profile on the degas settings page. When you are ready to
proceed, click the Start button.

EasyView displays the progress of the degas procedure by indicating the time remaining, the current power
level and the filament current being drawn.

8.12 Remote Vacuum Controller (RVC)

Click the RVC button on the Page Selection toolbar to reveal the RVC status.

You have full control over the RVC settings using this panel. You can start and stop the pump, select the
valve mode or open or close individual valves. Remember that, in order to open valves, the pump must be at
speed and the RGA filament must be on.

Process Eye Professional V5 –SP104008.100 August 2005 96

8.13 Cirrus
Click the Cirrus button on the Page Selection toolbar to reveal the Cirrus status.

The chamber pressure is the value obtained from the internal gauge situated close to the turbo pump. Click
on an indicator to change its state. If you have a multi-valve inlet you can change the active inlet using the
drop-down list. The list always shows the currently active inlet.

Process Eye Professional V5 –SP104008.100 August 2005 97

Chapter 9 – Calibrating the RGA Using Process Eye Professional
Note: The topic of calibrating the RGA using EasyView was covered in the previous chapter.

Overview
As with everything in Process Eye Professional, calibration involves the execution of a recipe. So calibration
has two parts – the recipe definition and the recipe execution. You also know that Process Eye Professional
supports six different sets of settings for the ion source parameters on most control units. Where these
collections of settings differ, each set will usually give rise to a different sensitivity for the ion source. Each
detector will give rise to a different sensitivity. Indeed the sensitivity when using the multiplier detector
depends directly on the multiplier voltage. That is the reason why Process Eye Professional allows you to
select three different multiplier voltages to work with (Multiplier 1, 2 and 3). Strictly speaking each filament
will produce a different sensitivity due to small differences in their position relative to the ion source. All
these combinations give rise to a total of 48 different possible calibration sensitivities maintained by Process
Eye Professional.

In practice there is often much commonality between the values or their relationships to one another.

A Faraday calibration uses the Faraday detector to compare the ion current associated with a particular mass
against the known partial pressure of that mass. A Faraday calibration defines the basic ion source sensitivity
in amps per pressure unit for a give set of ion source conditions. This is a fundamental property of a hot
filament ion source attached to a quadrupole RGA. It should fall within a relatively narrow range. When
outside that range the analyzer probably needs repair.

A multiplier detector calibration uses the basic ion source sensitivity to find a voltage that amplifies the ion
source signal by an amount that you specify. For this reason you should always run a Faraday calibration
immediately before a multiplier one.

This chapter describes the steps of defining a Faraday or multiplier calibration and then running it.

Process Eye Professional V5 –SP104008.100 August 2005 98

9.1 Defining a Faraday Calibration
To calibrate the instrument you first need to define a calibration for it to perform.

To define the calibration, select Define Faraday

Calibration Settings from the Instruments pull down
menu.

The RGA Calibration Wizard is started.

From the following dialog choose the instrument for

which the calibration is to be defined, and click Next.

Process Eye Professional V5 –SP104008.100 August 2005 99

 The Hardware Information dialog is displayed.

This details the hardware resources available to the

calibration recipe.

The Ion Source Selection dialog is displayed and

presents the opportunity to choose which ion source
configuration the calibration recipe is to be associated
with.

It also shows the details of any previous calibrations

defined for this instrument and ion source
configuration.

If the RGA has an inlet system, you will have a choice

of which inlet you assume is active when specifying
the pressure values in this recipe definition.

When correctly selected click Next.

The Calibration Mass and System Pressure dialog is

displayed.

Enter the following variables into the text boxes:

Mass to be used for Faraday calibration – the

mass used to base the calibration upon. It should be
a mass that you know has a reasonable peak height
when you run a barchart scan.

Usually you will simply enter a process chamber

pressure value in the edit box. However, if your
hardware has an inlet system and you have
configured the hardware to be able to calibrate the
inlet, you will have to enter an upstream and a
downstream pressure.

Enter the percentage contribution of the partial pressure of your selected mass to the gauge pressure
entered above. For example, you know that the contribution of mass 28 to an air spectrum is about 78%

Process Eye Professional V5 –SP104008.100 August 2005 100

When all the parameters have been entered correctly click Next.

Finally, the Run-time Options dialog is displayed.

If you normally use peak centered bar chart

measurements, be sure to check the Acquire data
from the peak centre only checkbox.

It is quite common to select the Apply to both

filaments check box also.

Select the required options and click Finish to complete

the calibration definition.

Firstly you will be asked to confirm that you want to define a new calibration, and then given the option to
run the newly defined calibration.

To run the calibration at this point, click Yes. If you choose not to
run the calibration at this time, it can be run at any time by
selecting Run a Defined Calibration from the Instruments pull
down menu.

If you choose Yes, the calibration that you have just defined will
automatically be selected when you run the calibration. This is explained in the section after next.

Process Eye Professional V5 –SP104008.100 August 2005 101

9.2 Defining a Multiplier Calibration Recipe
Note: A Faraday calibration should always be defined prior to a Multiplier calibration for a given ion source
configuration.

As in the Faraday calibration, go to the Instruments pull down menu, but this time select Define
Multiplier Calibration Settings.

Follow the same steps as in the definition of the Faraday calibration up until the Ion Source Selection
dialog. Here you can again select which ion source settings will be used for the calibration.

If a Faraday calibration has not yet been performed, the following dialog is displayed.

This simply states that whilst the multiplier calibration recipe will be defined relative to the current
(uncalibrated) Faraday sensitivity, executing this calibration is unlikely to produce a ‘calibrated’ result.
Normally you should click Cancel and define and run your Faraday calibration recipe first.

The Multiplier Detector dialog is displayed.

This dialog is used to choose which multiplier detector

configuration the calibration will apply to, and also
displays the details of any previous calibrations.

By convention Multiplier1 provides the lowest detector

amplification and Multiplier 3 the highest.

Click Next to continue.

The Pressure Scale dialog is displayed.

This dialog is used to choose the method employed to

perform the calibration.

Scaling to an external pressure gauge reading

uses the same methodology as the Faraday calibration.
At run-time you will enter the current process pressure.

In this example we will use the second method which

calibrates the multiplier to match the run-time reading
obtained using the Faraday detector.

Select the appropriate option and click Next.

Process Eye Professional V5 –SP104008.100 August 2005 102

 The Calibration Mass and System Pressure
dialog.

When performing a calibration against the

comparative Faraday detector reading all that is
required at this dialog is to enter the mass at which
the calibration will occur.

To continue, click Next.

The Multiplier Gain dialog is displayed.

This dialog allows you to choose how you want to

define the gain of the multiplier detector.

There are two choices;

Define the multiplier gain explicitly, where a user
defined gain setting is used for calibration,

Or

Define the gain in terms of the peak height I

need to measure where the maximum required
peak height is entered and the associated gain is then
calculated for calibration. Both methods are described
below:

Process Eye Professional V5 –SP104008.100 August 2005 103

Define the multiplier gain explicitly

In the resulting dialog simply enter the required gain

value into the text box.

The implications of the entered value are explained

along with the maximum and minimum detectable
partial pressures using this value of detector gain for
each electronic gain setting.

If you specify an impossible gain the dialog shows a

red Stop icon. Otherwise it shows a green ‘tick’
icon.

When complete, click Next.

Define the gain in terms of the peak height I need to measure.

In the resulting dialog simply enter the required

maximum detectable partial pressure into the text
box.

The calibration recipe will then calculate the detector

gain required to make this possible.

The implications of the entered value are explained

along with the maximum and minimum detectable
partial pressures using this value of detector gain for
each electronic gain setting.

If you specify an impossible value the dialog shows a

red Stop icon. Otherwise it shows a green ‘tick’
icon.

When complete, click Next.

The Run-time Options dialog is then displayed as in the Faraday calibration. Make any necessary choices
and click Finish to complete the definition of the multiplier calibration.

As in the Faraday calibration definition, you are asked if you are sure you want to define a new multiplier
calibration and if you would like to run the calibration.

To run the multiplier calibration, either click Yes now, or select Run a Defined Calibration from the
Instruments pull down menu.

Process Eye Professional V5 –SP104008.100 August 2005 104

9.3 Running a Faraday or Multiplier Calibration
Note: The calibration data is stored at the server and not at the client; so all users who connect to an
instrument, either locally or over the network, use the same calibration information. Once you have run a
calibration, you will change the calibration information for all users of that instrument.

Note: A Faraday calibration should always be defined and executed prior to a Multiplier calibration for a
given ion source configuration.

If you have just defined the calibration you will go straight to the Select an Instrument page. If you want
to run a calibration that you have already defined, make the Instruments | Run Calibration menu
selection.

The Select an Instrument dialog is displayed.

From the list, pick the instrument you wish to

calibrate. In this case, there is only one instrument
present.

This page shows the configurations for which a

calibration recipe has been defined.

Select the ion source configuration and then the

detector, click on Next to start the calibration.
You can define one Faraday calibration and three
multiplier calibrations for each ion source setting.

If you have started the calibration routine directly

from the definition wizard then the correct
instrument, ion source setting, and detector are
automatically selected, simply click Next to
continue.

The creation date and the date the calibration was

last run are shown in the Information panel.

Process Eye Professional V5 –SP104008.100 August 2005 105

 Depending on how the calibration recipe was
written, you may or may not need to enter the
actual chamber pressure.

If you have inlets that are being calibrated you will

have to enter values in both entry boxes. These
should be the pressures upstream and downstream
of the inlet orifice.

A number of factors are measured while the calibration routine is running. These include the peak maximum,
peak centre and stability.

Once the calibration routine has completed, click

Next to view the results.

When the calibration is complete, a report is

generated detailing the previous calibration factor
as well as the new one.

The graphic shown here is from a multiplier

calibration. At the end of a Faraday calibration you
have the option to apply either the new sensitivity
factor or to apply the factory default value.

If you choose Cancel no changes are made and the

control unit reverts to its previous calibration.

Details of all calibrations are logged in the application log file at one of the following locations
\..\Process Eye\Logs\Process.xml or
\..\Process Eye\Logs\Process.log or
\..\EasyView\Logs\Process.xml or
\..\EasyView\Logs\Process.log

On the final page of the calibration wizard, click on Finish to exit.

Process Eye Professional V5 –SP104008.100 August 2005 106

9.4 Calibration Alignment and Stability
When the calibration runs the software checks the stability of the partial pressure by taking ten separate
readings and calculation the standard deviation (sigma) of the sample.

If the value of 3 x sigma as a percentage of the first reading taken is:

Less than 1% the stability is excellent; otherwise if it is

Less than 3% the stability is good; otherwise if it is
Less than 10% the stability is acceptable;
otherwise the stability is poor.

Where the calibration is performed at the peak centre, the algorithm reports any misalignment of the peak in
increments of 1/32 of an a.m.u.

Process Eye Professional V5 –SP104008.100 August 2005 107

Chapter 10 – Customising the Workspace
Process Eye Professional and EasyView both allow extensive possibilities for personalizing the working
environment. You can customize the toolbars, re-organise the docking windows, personalize the colours
used for the displays and select a range of global preferences.

Note: some of the features described below do not apply to the EasyView workspace.

Process Eye Professional V5 –SP104008.100 August 2005 108

10.1 Modifying the Toolbars
Many buttons act on the active recipe (active connection in EasyView) or the active view. To activate a recipe
click on its tab in the status pane. To activate a view be sure to click in the view window,

10.1.1 The Default Toolbar

Run Recipe starts a recipe. Select the recipe from the recipe list and click on the Run Recipe button.

Interactive Disk Store starts disk store in an interactive recipe that has not been configured to store
to disk automatically.

Disk Store Pause is used to pause an interactive disk store; to un-pause, click again.

Close recipe halt a recipe that is currently running. The Close Recipe button will not be available
unless a recipe is running and the Status window has focus (click in the status window to give it
focus). Also, the recipe needs to have been configured to include the ability to end the recipe prematurely.
You can also close a recipe by clicking on the close button in the Status pane.

Lock used to lock the application by using a user specified password.

Recipe Wizard launches the Recipe Wizard program to enable you to edit recipes.

Recall launches the Recall program to allow the review of stored data.

Setup Wizard launches the Setup Wizard to allow changes to the software or hardware installation.
Having launched the Wizard you will have to close the RGA application because you cannot make
changes to the hardware/software setup while the application is running.

Print prints the data from the active data window.

Add Annotation used to add annotation at a particular time. It will be displayed on all the recipe’s
views.
Add Annotation at Selected Time used in conjunction with a trend to mark a particular event.

Calibration used to define Faraday and Multiplier calibrations (first two buttons), and to
perform a calibration of either kind (third button).

10.1.2 Window Arrangement Toolbar

Cascade button cascades all windows.

Tile Vertical button vertically tiles all windows.

Tile Horizontal button tiles all the windows horizontally.

Bring to Front button will bring the active window to the front.

Process Eye Professional V5 –SP104008.100 August 2005 109

10.1.3 Trend Display Toolbar

Add New Trend Window is used to add a new trend window and show the view definition wizard so
you can specify its properties. There is no limit to the number of trend windows you can associate with
a recipe / connection.
Note the button only becomes available when there is data to trend i.e. after the second scan is complete.

Key Display makes the legend key visible or invisible.

Key Position switches moves the legend key either to the left of the trend or above the trend.

10.1.4 Chart Display Toolbar

Properties displays the view settings for the active view window.

Grid displays a Y-axis grid in the currently active view window. Default is disabled.

Log/Lin switches between a linear and logarithmic Y-axis. Default is linear.

Y-axis Minor Ticks enables the display of minor ticks on the Y-axis. Default is major ticks.

Time switches between real and elapsed time on the X-axis from the start of the recipe. Default is
elapsed time.

Days displays the date and time on the X-axis. Default is time only.

X-axis Minor Ticks enables the display of minor ticks on the X-axis. Default is major ticks.

Add Scroll Bar adds a scroll bar to the X-axis. Default is no scroll bar.

Add Cursor adds a measurement cursor to the active Bar chart display. The cursor can be dragged to
the required mass and will display the mass number and partial pressure. As many cursors as are
required can be added. The yellow ‘flags’ can be dragged up or down to make adjacent mass information
visible.

10.1.5 Scan Navigation Toolbar

When the Historic Data button is not depressed, the active continuous mass scan view is displaying
the live data currently being acquired.
While the button is depressed, the continuous scan window will display historic data.
New data is still being acquired in this historic mode; you will see the total number of scans figure increasing
while the current scan number remains the same.

The six navigation buttons below will only become available when historic data is being viewed, e.g. The
Historic Data button is depressed.

First Scan views the oldest scan stored in memory.

Jump Back views the scan 10 scans previous to the current one being view.

Process Eye Professional V5 –SP104008.100 August 2005 110

 Previous Scan views the last scan.

Next Scan views the next scan.

Jump Forward views the scan 10 scans subsequent to the current one being view.

Last Scan views the newest scan acquired in the current recipe run.

10.1.6 Interactive Scan Navigation Toolbar

The Interactive Scan Toolbar becomes active when interactive recipes are running to allow you to modify
the scan parameters.

Control Unit Text Box is an information only box, giving the details of the control unit the recipe is
currently using.

Scan List box gives the name of the currently active measurement.

Accuracy drop down list allows you to make changes to the accuracy of the current scan.

Electronic Gain drop down list allows you to select the pre-amplifier gain.

Detector drop down list allows you to switch between Faraday and SCEM detectors.

First Mass text box allows you to select the start mass of the scan. You can either type in
the required number and press <Enter> or use the scroll arrows to scroll to the required
start mass.

Mass Span text box allows you to select the mass span of the scan. You can either type in the
required number and press <Enter> or use the scroll arrows to scroll to the required mass
span.

Restart Scan button will force the scan to restart.

Audio button is used to switch on/off the audio tone in the interactive leak check recipe.

Re-Zero button is used to take a new zero reading during a leak check measurement.

Process Eye Professional V5 –SP104008.100 August 2005 111

10.1.7 Customizing Toolbars

You can customize the toolbars as required. You can choose which Toolbars are visible or you can create
your own toolbars with your own choice of buttons.

From the view pull down menu, select Toolbars.

This will bring up the Toolbars dialog. Check the box for the toolbars you wish to have displayed. Checking
Cool Look will change the appearance of the toolbars.

To create a new toolbar, click on the New button.

Give the new Toolbar a name and click OK.

This will create a blank Toolbar that you can then customize.

From the toolbar dialog box click the Customize button to bring
up the customize dialog.

Click the Command tab to see the buttons currently assigned to

the new Toolbar you have created

Process Eye Professional V5 –SP104008.100 August 2005 112

You can drag one of the buttons (in this case the Create New Recipe button) onto the toolbar.

You can add as many buttons are you like from different toolbars. To save this new Toolbar, click OK.

This new Toolbar can then be positioned next to

the other toolbars.

Process Eye Professional V5 –SP104008.100 August 2005 113

10.2 – Graph Preferences
You can set the global properties of the views from the Graph Settings under Preferences.

The Graph Preferences dialog appears.

Here you can manipulate the various options used

in the graphs, size, colour, font and the style of
each item.

The dialog changes to reflect any changes that are

made.

Clicking on the Reset to Defaults button will

return all the settings, to their factory defaults.

The following diagram shows all the options that can be set. If the properties cannot be changed for a
selected item, they will remain “greyed-out”.

Select the ‘active’

item from the
Item drop-down
list. Then set its
properties from the
relevant size,
font, color and
style controls.

Use Restore to
Defaults to reset
to the factory
settings.

Process Eye Professional V5 –SP104008.100 August 2005 114

10.3 Other Preferences
The Preferences menu can be accessed from the Recipe pull-down menu.

10.3.1 Units of Pressure

Process Eye Professional supports the following pressure units, Pascal, mbar, Torr and mTorr.

The internal units used by all the applications in the RGA suite are Pascal and all internal pressure values are
stored in these units. You use the set-up applications to set the pressure units for all the applications;
however each application can also set its own units, depending on the preference set here. Pascal is simply
converted to the required unit, before displaying the information.

In addition all user variables that are labeled as pressures will also be converted from Pascal to the chosen
unit.

A “tick” in the selection indicates the currently used pressure unit.

All pressure axes will also be labeled with the current unit.

In this example, you can see that the Y-axis of the chart
is labeled in mbar.

To change this to Torr, click on Torr in the selection.

Process Eye Professional V5 –SP104008.100 August 2005 115

If any recipes are running, the peak heights will immediately change to represent this new measurement
unit.

The axis scale and label will only change

however, when the recipe is shutdown and
restarted.

The Maximum Peak Height information

will only change when Process Eye is
shutdown and restarted.

10.3.2 Auto View to front

When the RGA software is running all the views are displayed in the client area between the toolbars and the
status window. When more than one recipe or connection is active, it may be that some windows are
covered by views from a different recipe.

With the Auto View to Front checked, clicking on a tab at the bottom of the status pane will bring all those
recipe’s windows to the front.

In the status window, the tabs for the

running recipes are displayed. The
uppermost tab is the selected recipe.

In this example, Bar chart High Vacuum

with Disk Store is the selected recipe.

Clicking on the Analog Interactive tab

causes that recipe to become the active
recipe.

Process Eye Professional V5 –SP104008.100 August 2005 116

 If Auto View to Front is enabled, the views for the
active recipe are always on top.

The Analog Interactive view is shown when this

recipe is selected.

The Bar Chart High Vacuum with Disk Store view

is shown when this recipe is selected.

10.3.3 Show recipe error message boxes (Process Eye Professional)

If your recipes are all generated by the Wizard they are unlikely to cause errors, but if you have added your
own VB script code, an error may occur.

If a script error occurs in the recipe, you can choose whether or not to display an error message. In a
production environment you usually do not want to enable message boxes because there may not be anyone
available to accept it, whereas while you are developing the recipe you almost certainly do want to get a
message when an error occurs.

The message box gives useful information about the error that has occurred. If the error is a recognized
error type, then the error type is given along with the code that caused the problem, the line the code is on
and the recipe file name that contains the code. You are given the option of ‘debugging’ the recipe. If you
select Yes, the Recipe Wizard application will open the recipe at the offending line.

If the Show Recipe Error Message Boxes is not enabled, then the recipe will just abort on encountering
an error.

In all cases recipe errors are logged to the application log file in your Logs folder.

Process Eye Professional V5 –SP104008.100 August 2005 117

Chapter 11 – The Main Application Menus
Note: Some of the menus described in this chapter are not available in EasyView, nor are they available in
Process Eye Professional if, as an Administrative Option, you elected to use the Restricted User Interface.

11.1.1 Recipe Menu

The features accessed from the recipe menu have been fully described in the earlier chapters.

11.1.2 Instruments Pull-Down Menu (Process Eye Professional only)

From this menu the Connections dialog can be accessed,

and calibrations can be defined and performed.

In EasyView the Connections menu item is on the Recipe

menu.

11.1.3 View Pull-Down Menu

This menu can be used to set up the appearance of Process Eye.

Toolbars

Opens the Toolbars edit dialog.

Process Eye Professional V5 –SP104008.100 August 2005 118

The Status Bar

The Status Bar appears at the bottom of the screen.

To make the Status Bar visible/invisible, click on the Status Bar item in the pull-down menu.

If a check is visible, then the Status Bar will be visible.

Recipe List Window

The Recipe List window is the list of all the currently loaded recipes.

This window can be resized and can be docked or floating; however if you close it, you can only bring it back
by re-checking the item in the View menu.

Check the Recipe List Window entry to make the recipe list visible or
invisible.

Various functions are also available by clicking on a recipe in the recipe list window with the right mouse
button.

Run to start this recipe.

Edit to use the Recipe Wizard to edit this recipe.

New to create a new wizard recipe.

Recall Data to open the Recall program in the directory

associated with data stored in this recipe.

Allow Docking to make the recipe list dockable. If this selection

is not checked then the recipe list behaves as a floating window.

Process Eye Professional V5 –SP104008.100 August 2005 119

Select Hide to close the recipe list. It can then only be made visible by selecting Recipe List Window in
the view pull down menu.

The Show instruments and Show dates functions have the same function as those in the view pull down
menu, described below.

Show Instruments

To show the instrument that a recipe is written for in the recipe list window, click on the Show
Instruments item in the view pull down menu.

Generic recipes will have an “unspecified” instrument, recipes that do not use an
instrument will have “None required” as the instrument.
Otherwise the instrument details that the recipe was written for will appear.

Show Dates

To show the date a recipe was created in the recipe list window, click on the Show Dates item the View
pull down menu.

This will add dates to the recipe list window.

These are the dates the recipes were added to the list, or modified
using the Recipe Wizard. If you edit the script of the recipe, then the
date is not updated.

Process Eye Professional V5 –SP104008.100 August 2005 120

Properties

The Properties item will only be active if a recipe is running with a view loaded.

Click on the Properties button to bring up the view properties of the active
view.

If the view is a trend, the Trend Properties dialog is

displayed.

If the view is a swept measurement, the Swept

Measurement View Properties dialog is displayed.

Process Eye Professional V5 –SP104008.100 August 2005 121

11.1.4 Window pull down menu

The Window pull-down menu is where you can add a new

trend view or arrange the view windows you already have.

New Trend Window

Clicking on new trend window will bring up the Trend

Properties window for a new view. Fill in the pages that
follow and the new view will be created in addition to any
views that already exist.

You can add as many trend views as you need. The same
data can appear on more than one view.

Arrange All Windows

This item will bring up an additional list.

From here, you can arrange the windows in the usual way. In this menu however,
all the currently open views from all the currently running recipes will be arranged.

The other window arrangement methods in this pull down menu apply only to the active recipe.

Process Eye Professional V5 –SP104008.100 August 2005 122

Bring Recipe to Front
This item brings the views for the current active recipe to the front.

In this case there are 2 views for the active recipe

(Barchart with Trend Interactive) and one view for
the inactive recipe (Demo with no instrument).

If Bring Recipe to Front is clicked, the two Bar chart with Trend Interactive views are overlaid on the
other view.

Cascade Recipe
Brings the views for the current active recipe to the front and arranges them in cascade mode.

Tile Recipe Horizontally

Brings the views for the current active recipe to the front and tiles them horizontally.

Tile Recipe Vertically

Brings the views for the current active recipe to the front and tiles them vertically.

Selecting Individual View

The bottom section of the pull down list contains a list of the
currently open views. The current active view is indicated by a
tick next to it.

To make a different view active, click on that view. As well as

making this the active view it will also bring the view to the
front.

Process Eye Professional V5 –SP104008.100 August 2005 123

11.1.5 Help Pull down Menu

The help pull down menu is were you can access the online help, or get
information about the Process Eye program

If you need to contact MKS about your software please have the version of
Process Eye Professional or EasyView available. Click on About Process.. to obtain this information.

Process Eye Professional V5 –SP104008.100 August 2005 124

Chapter 12 – Printing

Both Print Setup and Print can be accessed from the recipe pull-down menu.
Unless a recipe is running, the Print option is grayed out, as the print function only works with the active
view.

In addition there is a print button on the tool bar.

12.1.1 Print Setup

Selecting Print Setup from the Recipe pull-down menu will bring up a standard Windows print properties
dialog.

From here, you can configure the printer for paper

size, orientation etc.

Printing a View

Click on the view you wish to print, so it becomes the active view.
Then either click on the Print button or select Print from the recipe pull-down menu.

If you click on the print button, the print will start immediately with the default settings. If you select Print
from the recipe pull-down menu, the standard Windows print dialog appears giving you the option to change
the default printer settings.

You can only print swept measurement views and trends, other views within Process Eye cannot be printed.

If you require a hard-copy of these other views, use the Print Screen key on the keyboard.

Information contained on a trend printout:

The key at the foot of the printout shows the colour of the line, the channel name and the value of the trend
line at the start and finish of the trend printout.

There is no title or foot note feature in the print facility.

You can however give the printout a title by adding a caption to the view -

Process Eye Professional V5 –SP104008.100 August 2005 125

In the Save View dialog of the view properties, add the required title to the Optional Screen Title text
box.

The trend view caption then appears as a title on the printout.

Process Eye Professional V5 –SP104008.100 August 2005 126

Chapter 13 – Process Eye Tools

13.1 Backup and Recover

The backup and recover tool is used to backup the current Process Eye installation. The tool will backup all
recipes and views as well as the registry settings for the current user.

To run, select Backup and Recover from Start | MKS RGA Applications | Tools.

This will bring up the System Backup

dialog, choose the location and name for
the backup file.

To make a backup spanned across a number of disks, click the Multiple Zip files to fit on option and
select the type of media. There is also a custom size option, simply select and then enter the size of files to
be created

If reports are also to be backed up check the relevant check boxes

When the options have been selected, click Start Backup.

To restore a backed-up installation click on the Restore tab.

Click on Browse and select the backup

file required from the standard file open
dialog.

To begin the restore process, click on

Start Restore.

Process Eye Professional V5 –SP104008.100 August 2005 127

13.2 Computer Lock
Process Eye has the ability to lock the computer to prevent unauthorised use. The utility provides more
functionality that the standard windows password-protected screen saver; although the RGA application
display remains visible and continues to be updated, the keyboard and mouse are disabled so it is not
possible to switch from Process Eye to another running application.

This utility is different from the simple ‘Lock’ feature built in to Process Eye and described in
chapter 10. It supports the concept of defined users and administrators (who are not the same as
regular Windows users and administrators).

To run this utility select Lock This Computer from Start | MKS RGA Applications | Tools.

The initial username and password is

displayed.
Username “admin” and a blank
password field; click Yes to continue.

The computer will now be locked.

To unlock the computer type “admin” in the UserName text box and
then click Logon.

To lock the PC, click Lock PC.

If you do nothing (i.e. no mouse actions or key presses) the PC will be
locked after 5 minutes.

To configure the Lock PC utility, click Configure.

From configure you can create, edit and delete users. You can also
change the time without use before the computer is locked.

When run for the first time, the first action should be to create a
new user, to do this click Add New User.

Process Eye Professional V5 –SP104008.100 August 2005 128

 Enter a new user name and password.

Two options are possible for this new user:

This User Can Create/Edit/Delete Users allows

administrative privileges over the other users.
Note: Never delete the original default user until at
least one user with administrative privileges has
been created

Enable Windows security buttons on Ctrl+Alt+Del; normally the user can use ctrl+alt+del to bring up
the windows security dialog and then log off or shut down the computer. Un-check the box to prevent this
from happening. Note: some Windows systems do not support this particular functionality.

The new user will now appear in the list; click OK to continue.

Log on as the new user by entering the new username and

password.

It is not possible to click on Configure and delete the “admin”

user.

Process Eye Professional V5 –SP104008.100 August 2005 129

13.3 Process Eye Watchdog
The process eye watchdog utility monitors the performance of the Process Eye program. If it detects a
problem with Process Eye it will attempt to restart the program.

Ensure that Process Eye is not running. Then select Process Eye Watchdog from Start | MKS RGA
Applications | Tools

The watchdog will start Process Eye; to configure the watchdog double click on the icon in the
taskbar.

The watchdog can be temporarily disabled by selecting the

second option box. You will have to confirm that you are the
currently logged on user of the Windows session using your
normal Windows logon name and password.

However the program will automatically restart when Windows

reboots, or if Process Eye is restarted, or when you re-select
automatic mode.

On many installations you can check the box to have Windows

reboot if the watchdog fails to restart Process Eye three times
within a short time period.

There is full help and more description of the watchdog configuration options. Click Start | Programs |
MKS RGA Applications | Help.

Process Eye Professional V5 –SP104008.100 August 2005 130

Appendix 1 – Network Hardware and IP Addresses

It is increasingly common for RGA control units to be fitted with TCP/IP network connectivity. This is a very
useful feature; it allows connection over long distances, it is easy for multiple users to share hardware and it
makes it possible to benefit from features such as browsing the control unit with a simple web browser.

However to take advantage of all these benefits you have to understand how to give the control unit an IP
address; every entity on a network has to have a unique address by which it can be identified.

IP addresses are usually expressed as four numbers separated by a ‘dot’ (full stop or point mark). So, for
example, the default address of a control unit when it leaves the factory is 192.168.0.250. The numbers
range from 0 to 255. In addition to the unique IP address you also have to specify a subnet mask, which
has the same format but which for most users will always be 255.255.255.0. If you understand binary
numbers you will recognize this as a bit pattern of 24 1’s followed by 8 0’s. The 1’s mask the part of the
address that is the network identifier, while the 0’s mask the part of the address that is the identifier of the
particular entity on the network. So in this example the network is the 192.168.0.0 network and the control
unit would have the ID of 250 on that network.

If your computer is already on a network, you should know your address and subnet mask – it may be the
192.169.0.0 network but it may not.

If you are not connected to a network, you will need to configure your computer (as the administrator and
using control panel) to have a fixed IP address. MKS suggests that you set your computer up to be
192.168.0.1 with a subnet mask of 255.255.255.0. If you have more than one control unit, you will need a
small network switch to which you connect your computer and your control units. If you just have the one
control unit you can connect it directly to the computer, but you must use a special network cable called a
crossover cable (this just crosses over the send and receive wires at either end).

Assuming that you have multiple control units decide in advance what the address for each will be. They
must all be different and the must be different from every other entity on the physical cabled network.

So what is an IP address and how should you decide what it should be?

You can imagine a busy industrial park with all the world’s major corporations having their head office
located within it. You want to send a good old fashioned letter to the human resources department of one of
these companies, asking them for a job. Your letter arrives at the busy mail sorting office along with
hundreds of other letters for the good residents of the city. The street name and company name identify
which postman has the job of delivering your letter. When he delivers it to the mail room of your chosen
future employer, someone identifies it as needing to be routed to the human resources department.

Your IP address system is very similar. The 192.168.0.0 network identified the street where the company
was located. The entity ID (eg 250) identified the specific company in that street. When it was delivered the
letter was routed to a particular department – in IP addressing terms a particular port (numbered between 1
and 65535). Just as someone may have been anticipating your job application, so software can be
configured to ‘listen’ for messages on a particular port. The RGA data server ‘listens’ for clients that wish to
connect.

The developers of the internet foresaw that providing a unique address for everyone in the world would be
cumbersome and unnecessary. Unlike the postal system where everyone might want to contact everyone
else, they saw that most of the time it would only be necessary for the residents of one street to
communicate with each other. You do not need (or want) everyone in the world to talk to your RGA. So
there can be many thousands of 192.168.0.0 networks around the world – so long as they are not wired
together you will never know whether they exist or not. If you do need to get access to the outside world
you do it through a particular address on your network called a gateway. The gateway manages the
connection between you and the outside world.

Process Eye Professional V5 –SP104008.100 August 2005 131

So how do you choose an IP address for your control unit? First find out the IP address and subnet mask for
your computer. Write this down. Confirm from the description above which part of the address is the
network part and which part (normally the final number) is the identifier on the network.

If there are other computers on the network you need to know their identifiers so that you do not
inadvertently use their address for your control unit. Once you have chosen a unique address (for example
192.168.0.50) MKS recommends that you physically label the control unit with the address you have chosen
and then run the RGA Device Manager application that you can use to program the new address.

Process Eye Professional V5 –SP104008.100 August 2005 132