Science at Ultra-Brieftime Periods From The Attosecond To The Petawatt
Science at Ultra-Brieftime Periods From The Attosecond To The Petawatt
Science at Ultra-Brieftime Periods From The Attosecond To The Petawatt
Recommendations 1 - Research By enabling action on matter in a controlled way at the scale of molecular vibrations and by opening up the possibility of monitoring the development of the system with the same time resolution, ultra-short lasers have provided physics, chemistry and biology with research tools of unexpected power. On entering the domain of the femtosecond then of the attosecond, optics go way beyond a simple extension of the physics of the nanosecond. The combination of the brevity and high power densities effectively gives access to a class of phenomena which was only studied previously in a very indirect way. Already at the origin of major discoveries and a valuable improvement in understanding, ultra-short time science will, undoubtedly, experience spectacular expansion as a research tool in a variety of disciplines. Whether this involves chemical reactions, new concepts of accelerators, sources of radiation, macromolecules, aggregates, treatment of materials, the successes already achieved are only a small opening to the routes of decisive progress, impossible to define in a precise manner, but which demand the continuation and the coordination of the research and development over the next decade. In chemistry, the justification, on microscopic bases, of the global mechanisms of reactional dynamics should extend to more complex reactions, in particular to those which are important in the biological mediums such as charge transfer or the evolutions in hydrogen links. After the success of the study of photodissociative reactions, femtochemistry will turn to the more general problem of bimolecular reactions in the fundamental state. It is therefore necessary to determine the electronic distributions based on the detection of photoelectrons, the movement of ions using the diffraction of electrons or X-rays or by provoking the coulombian explosion of the molecule, the changes in the mode of vibration during the reaction by non-linear spectroscopy.
These advances demand impulses with variable duration and as short as possible, a maximum frequency of the order of several kHz, as well as an improvement in the quality of the signals. Impulses of a half optical cycle in the visible and UV area will enable the molecules to be subjected to very well controlled disturbances, as is already possible in infrared. For complex systems, in particular in the dense phase, it is necessary to overcome the relaxation which is responsible for the extreme rapidity of the loss of coherence. The reduction in the duration of the impulses is one of the routes to be followed. Access o the domain of the attosecond, through the use of coherent X-sources, will enable direct observation of the deformation of the electron cloud during the reaction and so understand the mechanism involved. In biology, although it is necessary to remain prudent on the real increase in the contribution of femtochemistry, it is certain that the major part is yet to come. On the one hand, the analysis of the in vitro functional dynamic within the protein matrix itself with the characterisation of the active functional structures is particularly crucial to the understanding of the mechanisms of enzymatic catalysis and the development of a rational approach in the development of medicament-molecules belonging to the inhibitor class. This axis will directly benefit from the progress in the area of secondary sources (secondary X-ray sources and femtosecond infrared sources) and from the photoactivation of reactions, in particular within crystals, whether through the synthesis of cofactors in the photo-commutable pharmacological properties or through the direct control of the reaction. On the other hand, in the context of functional genomics, intensive efforts are required in the analysis of in situ cellular operation. They must be based on developments in multi-photonic cellular imaging combining methods of detection of fluorescence in single molecules and functional cellular physiology. The grouping together at a single site of the sources, the instrumentation and skills required will be a very favourable factor in the dynamism of these activities. In condensed matter physics, the brevity of the energy deposition generates new modes of interaction of the radiation with the material which gives rise to athermic phenomena of which the physics have yet to be explored and understood (non thermal diffusion of the energy, role of the coulombian explosions, new phases). The analysis of these phenomena demands diagnostics enabling monitoring of the evolution of the network on appropriate time and space scales, which requires ultra-short X-ray source. Several types of these sources are already available, but, here again, efforts must be directed towards flexibility, availability and reliability. Over and above the question of the investment required, this also raises the problem of the quality of the optics (reflectivity, selectivity...) and the operating rate of the sources which is far from being adequate enough to envisage diverse and intensive operation. Ultra-intense laser sources have already given plasma physics unexpected dynamism and renewal. They have opened the door to research into relativistic plasmas. Total control over this state of matter is not achieved and it is necessary to wait for a better understanding and improved modelling to be able to estimate their real interest. The same
does not apply to the mechanisms of radiation from unbalanced plasma created by ultrashort and ultra-intense impulses: in this domain the results are already sufficient to demonstrate the unique and specific character of the phenomena observed together with the significance of the applications. The acceleration of particles, after it recent successes, must lead to mechanisms with low acceleration over longer lengths and faster beam quality control. The techniques of control and correction of the wave edge will improve lasers. Energy flux densities higher than 1022 W/cm2 should be obtained over the next decade which will lead to ponderomotor voltages in the gigaelectronvolt area. However, the contrast of the impulses must follow this progression to prevent the pedestal disturbance effects. Over the next few years, ultra-short time science will continue to contribute in a significant way to fundamental research. Probable acceleration will result from the widespread use of diode oscillation which, like solid lasers and frequency drift amplification, will enable a faster and more diverse spread of laser source application. This dynamism should help the development of a number of domains by contributing a very pronounced multidisciplinary character, resulting from the sharing of analysis and measurement techniques. In particular, coherent control and optimal control open up very attractive perspectives in chemistry, in condensed matter and in biology. Their improvement is a major opportunity which demands theoretical effort, methods of calculation and the implementation of true engineering of the conformation of the impulses in phase and amplitude. These aspects should be subject to special attention. 2 - Laser source technology In France, several laboratories have played a front-line international role in the history of ultra-short impulses and yet, at least in the short term, the official research authorities have only provided, at best, modest support and, in any event far less than that provided in the USA and in Germany, or even in Japan. In the same way, in opposition to the USA, French companies have not sought to develop these technologies at their beginning with the result that it is only recently that French industry has taken a significant place in the manufacture of these sources. On the other hand, it should be noted that the French have often initiated the necessary basic technologies, but in the USA! This emphatically demonstrates that it is time to help the necessary development in France, in particular in the area of company start-ups close to the laboratories. Sapphire-titanium lasers now reach the ultimate limits in impulse duration compatible with the visible spectral range and to near infrared. The techniques of frequency drift amplification fix a very high limit to impulse energy, but the rate of repetition decreases very quickly with the energy. The need for progress is felt regarding the rate of repetition, but also for the accordance in frequency and the extension of the spectral range. Parametric amplifiers already provide a solution for low energies on the infrared side and for accordance in the visible zone through combination with a spectral continuum generator. For short wavelengths, the multiplication of frequencies is an acceptably efficient simple solution. In several domains, the dynamism of the activities will be significantly enhanced by the presence in a single location of sources covering the whole range of the spectrum, from infrared to X-rays.
The non linear interaction of laser pulses with photoconductors has equally enabled the generation of ultra-short impulses in the terahertz area (300 microns). On the one hand, this area is that which needs to be mastered for the study of the most recent miniaturised electronic components and only optoelectronics is able to do this. The principle is now well established and the technique is at the stage of final development to make it transparent to users. Problems remain at the level of the components to be analysed which do not always lend themselves easily to this study. On the other hand, the introduction of bright broadband Terahertz sources operating at ambient temperature has revolutionised spectroscopy in the medium infrared zone, a central area for molecular physics and transmission mechanisms in solids. Finally, Terahertz impulses have applications in medical imaging to view small structures, the detection of pollutants, protected short range communication or non destructive imaging. There remains the adaptation of the generation techniques to the various applications and obtaining the required intensities. As far as applications are concerned, the fastest progress will come from simplification, from the reliability and compact size of the sources, in particular to facilitate their integration into systems. Demand should be high, and it's a top priority, for intermediate power (10 gigawatt to 1 terawatt) high frequency (1 to 100 kilohertz) sources with the presence of a specialist, particularly for server centre installations. The development of these lasers with a high repetition rate depends on an improvement in the oscillation technique and, today, only laser diodes offer a promising solution. It is therefore necessary to underline the major importance of the technological development of laser diodes and the active pursuit of the search for optimised laser materials for short impulses, in order to extend the choice and adapt them to very wide range of requirements. Sources combining short impulses, short wavelength and very high frequencies require a class Very Large Equipement installation, with a very high cost and access to a very small number of units. One exception is the free electron ultraviolet laser for which the cost is comparable to that of a high power laser installation. The case of the free electron ultraviolet laser cannot be dissociated from the accelerator (storage ring) on which it is built. The solution of inserting an FEL-UV on a ring dedicated to synchrotron radiation, hence with a large number of other users, is attractive if such a ring is equally constructed with this aim. The construction of such FELs which have more than demonstrated their power (average and peak) and successful applications, does not involve major technological risks. This is not the case of free electron lasers of the "Self Amplified Spontaneous Emission" type (SASE), for which the hopes of high performance are great, but the magnitude of the technological risks also. Even if the initial amplification result was obtained in 2000 at 109 nm in Germany, the specialists agree on the fact that the perspective of obtaining a femtosecond X-laser is not possible within the next 20 or 30 years. It would therefore be unreasonable, if choices must be made in the area of new lasers for economic reasons, to give preference to a French FELSASE, with respect to the priority stated above rather than to intermediate power high frequency sources. Other less expensive solutions may be encouraged through cooperation with those European countries already active in this area.
Very high power energy sources remain few in number and are designed for very special applications, in particular for defence. Nevertheless, it is from these sources that the most spectacular scientific breakthroughs must be expected. They provide within reach of university laboratories, nuclear physics experiments which were only possible using large or very large instruments. Through them, a revolutionary concept of particle acceleration techniques is perhaps about to see the light of day. They enable the creation of very dense mediums with a very high energy density which become intense sources of X or gamma photons. It would be surprising if, one day, they do not appear in the systems designed for the control of thermonuclear energy in the laboratory. Other diverse applications will probably follow, but today, if these sources give rise to obvious interest on the part of research workers and students, it is because they cover, in physics, new ground to be broken in and domesticated. In a general way, it is no longer the pursuit of record performances which should motivate future development, but more the wealth and extent of possible uses. It is nevertheless true that the newness of the expected effects justifies the search for still higher energy flows. Powerful national installations, largely open in Europe, have their place in this context.
3 - Measurements In the domain of ultra-short times, measurements present specific problems as, on the one hand the impulse durations are shorter than those which have been explored in the traditional electromagnetic domain (there is no oscilloscope able to read femtoseconds) and, on the other hand, it is necessary to find a complete characterisation of the variation of the optic field as a function of time and not only the energy and pulse frequency. The analysis of signals by fast photoconductors seems to have reached its limit. Today, this type of study is as much involved with very broad band optical telecommunications as with ultra-short impulses. In spite of a significant industrial involvement in optical telecommunications, through Alcatel and Thomson, the link with the domain of ultrashort impulses remains marginal in France. Measurements without reference in non linear optics have made remarkable experimental and methodological progress. No further revolution in principle is expected, but rather an improvement in performance and convenience of use. This may well prove essential for development leading to self-adapting (smart) lasers. In this domain, the French teams, without having really been pioneers, have played a significant role in finalising the methods and continue to be active. Measurements with reference are older. France is present in the area of aperture scan cameras which may progress further towards an objective of the order of 200 femtoseconds with the possibility of detection of single photons. France is equally present in the area of time control where one of the two main methods being studied is a French invention. 4 - Simulation and interpretation of results
Ultra-short time physics is often associated with digital simulation work which finds in the experiments an ideal field of application and which considerably helps the analysis of the coherent phenomena observed. The brevity of the laser-matter interaction enables, in many cases, to avoid the phenomena of relaxation which are not easy to integrate into a simulation. The ab initio description becomes possible. Quantum chemistry, molecular dynamics, special models are then used to describe the phenomenon studied in a near rigorous way, and simulation becomes a tool for forecasting and analysis in chemistry, in biology and in plasma physics. It is therefore necessary to ensure that the skills needed for the development of these digital tools are kept at the required level with adequate computer availability. In the dense phase, the theoretical modelling must adapt itself to the complexity of the medium in order to go beyond the limits of quantum chemistry. The French teams must possess the appropriate tools in order, for example, to design the format of the femtosecond impulses suited to the loss of coherence in the liquid phase and hence master the coherent control in the experimental conditions of the dense phase. 5 - Environmental applications The Lidar technique (Light Detection and Ranging) has already shown the effectiveness of optics as a means of detection and characterisation of atmospheric pollution. Femtosecond non linear spectroscopy has now provided a major complement by enabling the characterisation of aerosols whose impact on the environment is increasingly recognised. The emission of harmonics, the Raman distribution and the multiphonic induced fluorescent give indications of the size and composition of aerosols. New perspectives are opened with the discovery of the generation of white light, in filaments, at kilometric distances using Terawatt Lidars. Europe and France are well placed in the latter domain with the TERAMOBILE Franco-German project, but the experimental effort must be accompanied by theoretical developments and sophisticated modelling. Applications relating to the initiation of lightning are equally under study, but have not yet got beyond the exploratory stage. 6 - Industrial prospects Today, industrial production basically relates to scientific applications of ultra-short sources in the laboratory. These scientific applications require specific instruments that the specialist manufacturers produce, sometimes in partnership. The clientele is invariably made up of laboratories, but it is increasingly broad and covering increasingly diverse sectors of research. Two major examples can be cited where an association of manufacturers has been established naturally. The first involves confocal microscopes with two photons. Its two main components are a laser oscillator with adjustable wavelength and a confocal microscope. There is currently a link established between the laser and the microscope manufacturers to market this type of instrument. Another specific application example currently being established involves Terahertz spectroscopy. This application requires a partnership between laser manufacturers and manufacturers of fast semiconductor sensors.
Applications should soon appear from laboratories in the medical sector (ocular microsurgery and diagnosis) as well as for material processing and machining. It should, however, be noted that problems of the reduction in cost, reduction in size, operational reliability and simplification of use are not yet dealt with. In certain cases, such as micromachining, ocular microsurgery or initiating lightning, the applications are still at the laboratory demonstration stage, in other cases they have not managed to replace more traditional techniques. It is the lack of really easy to use sources which is the most important brake. Research must be started or pursued into a certain number of key points for the simplification and cost reduction of lasers, such as the final development stages of laser material having both adequate performance characteristics (broad band, laser gain, thermal properties, etc.) and compatibility with diode oscillation or the final development of compact spectral dispersion systems. It is very probable that the phase of non scientific applications will begin during the course of the decade. France has advantages in this context, among which could be cited: - a university community active in this field - one of the major international industrial manufacturers of lasers, who is the leader in the area of high energy applications - a manufacturer of tubes for aperture scan cameras, equally at the highest international level - a number of small and medium sized businesses active in the development of components associated with lasers. 7 - The international context France recently took a significant place in the industrial production of femtosecond technologies. Three independent industrial entities (QUANTEL, B.M. Industries (now known as Thomson CSF Laser) in France and CONTINUUM in the USA) whose managers were previously members of the first QUANTEL team, supply more than 50% of the world market for these sources. As far as free electron lasers are concerned, the French community has shown that it has made undeniable international progress. The CLIO infrared FEL at the LURE at Orsay constitutes an exemplary server centre. The case of the FEL-SASE is linked to the success of the Hamburg project. The CEA has already begun the construction of the accelerator and has also started test experiments on the future FEL via a European network. In the area of coherent control, the scientific community involved is very scattered, with pioneering groups in the USA, in Israel and in Germany, particularly in physical chemistry applications. In Japan, major developments have taken place in the solid phase. On the French side, the numbers involved are still small. Although there are groups of theoreticians at Orsay and Dijon, research workers at Orsay, Palaiseau, Toulouse and Dijon are already very active in this domain, this community must certainly be strengthened.
In femtochemistry, the teams are numerous and mainly located in the USA, Germany, the Netherlands, Belgium, Italy and France. Our country has at least ten groups involved in this area. Most of the French teams are grouped within the GDR CNRS N1017 "Elementary chemical action in the liquid phase". The domain of condensed matter studied at ultra-short time scales includes aspects close to industrial production. It is therefore difficult to situate the respective positions of the various countries in competition. The Americans have been pioneers in this study, but France and Germany have quickly taken a significant place, followed by Canada, Switzerland, Denmark and a few other countries. The Japanese, with few exceptions long absent, could soon become serious competitors through the major research effort in this area decided by their government. France has played the leading role in ultra-intense high energy lasers based on Nd-glass with the P102 installation of the Atomic Energy Commission Military Applications Management, retaining the world record for peak power over a long period. The projects in progress will maintain this lead in Europe, in spite of the construction of several highperformance lasers in Great Britain and Germany. France remains extremely well placed in the competition with the USA and Japan