0% found this document useful (0 votes)
28 views10 pages

2 Quarter Summative Test in Computer System Servicing

2 quarter Summative test in Computer System Servicing
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
28 views10 pages

2 Quarter Summative Test in Computer System Servicing

2 quarter Summative test in Computer System Servicing
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 10

Summative test in Computer System

Servicing

Part 1: Multiple Choice

1. A successful task can be achieved through


planning and preparation.
A. safety and proper
B. understanding the scope
C. giving enough time
D. all of the above

2. The action or process of making ready or


being made ready for use or consideration
is called:
A. preparing
B. planning
C. requiring
D. scheduling

3. Which tool is used to prevent static


electricity from building up on hardware?
A. Anti-static mat
B. Philips head screwdriver
C. Hex driver
D. Wire cutter

4. Which tool is used to blow away dust and


debris from different computer parts
without touching the components?
A. Anti-static mat
B. Hex driver
C. Compressed air
D. Wire cutter

5. The process of thinking about the


activities required to achieve a desired
goal is called:
A. preparing
B. planning
C. requiring
D. scheduling

6. Which of the following is used for cleaning


computer components without scratching
or leaving debris?
A. Part retriever
B. Lint-free cloth
C. Flat-head screwdriver
D. Cable ties
7. The identification of something as being
of a certain kind is called:
A. recognition
B. selection
C. elimination
D. comparison

8. One factor to consider when planning and


preparing for a task to avoid accidents is:
A. materials
B. place
C. safety
D. waste disposal

9. Which tool is used to cut ropes or wires?


A. LAN Tester
B. Utility Knife
C. Screwdriver
D. Pliers

10. The safe condition of hand tools used


on the job is the responsibility of:
A. The employee
B. The employer
C. Both A and B
D. Manufacturer

Part 2: True or False

11. A Gigabyte has 1,024 Megabytes.


A. True
B. False

12. A byte is the smallest representation of


data.
A. True
B. False

13. We use the term kilo to represent


storage space.
A. True
B. False

14. A bit is the smallest unit of measure.


A. True
B. False
15. A Megabyte has 1,048,576 Bytes.
A. True
B. False

Part 3: Fill in the Blanks

16. The purpose of an antistatic wrist strap is to


__________ the electrical charge between you
and the equipment.
17. Turn the screwdriver __________ to tighten
the screw.
18. Turn the screwdriver __________ to loosen the
screw.
19. Use a __________ head screwdriver with
crosshead screws.
20. On electrical components, an excessive
build-up of dust will act like an __________ and
trap the heat.
21. Which tool is used to measure
resistance, voltage, and current?
A. Wire cutter
B. Soldering iron
C. Digital multimeter
D. Pliers

22. Which of the following allows the flow


of current in two directions?
A. DC
B. AC
C. CA
D. CD

23. Which safety device is used to protect


an electrical circuit from excessive
current?
A. Fuse
B. Switch
C. Conductor
D. Voltage source

24. Which type of cable has conductors


inside it and is used for exposed or
concealed installations?
A. Fiber optic cable
B. Non-metallic sheathed cable
C. Power cable
D. Thermoplastic wires

25. What is used to join two metal


conductors with soldering lead melted
around it?
A. Soldering iron
B. Wire cutter
C. Multi-tester
D. Screwdriver

26. It is an electronic measuring


instrument that combines several
measurement functions in one unit.
A. Digital multimeter
B. Soldering iron
C. Oscilloscope
D. Clamp meter

27. These are used to connect to whatever


device you're planning on testing and
measuring.
A. Probes
B. Soldering wire
C. Wires
D. Leads

28. This small knob is usually located near


the dial and is labeled "Ohms Adjust" or
"0 Adj."
A. Zero adjustment knob
B. Function selector
C. Sensitivity knob
D. Voltage knob

29. This allows you to change the function


between volts, ohms, and amps, and
change the scale of the meter.
A. Function selector
B. Voltage knob
C. Zero adjust knob
D. Test lead

30. This has arc-shaped scales visible


through the window and a pointer
indicating the values.
A. Analog multimeter
B. Digital multimeter
C. Oscilloscope
D. Digital thermometer

31. These are components used to resist


the flow of electric current.
A. Resistors
B. Capacitors
C. Diodes
D. Transistors

32. This system is used to determine the


value of a resistor without using a
multimeter.
A. Color code system
B. Ohm’s Law
C. Fourier analysis
D. Circuit analyzer

33. A defective capacitor that will not show


any movement on the OHM meter screen.
A. Shorted capacitor
B. Open capacitor
C. Leaky capacitor
D. Faulty capacitor

34. A type of transformer used to increase


the output voltage.
A. Step-up transformer
B. Step-down transformer
C. Isolation transformer
D. Current transformer

35. A type of transformer used to decrease


the output voltage.
A. Step-up transformer
B. Step-down transformer
C. Isolation transformer
D. Current transformer

36. Which tool is used for boring holes?


A. Hammer
B. Drill
C. Pliers
D. Wire cutter

37. What should you do before using


cutting tools?
A. Check the blade for wear
B. Hold the object with your hand
C. Use force to cut
D. Ignore safety guidelines

38. What safety measure should be taken


when using electrical test equipment?
A. Only use with dry hands
B. Use when equipment is powered off
C. Always check for voltage before use
D. Use without safety gloves

39. What is the correct way to store hand


tools?
A. In a dry place
B. In direct sunlight
C. Exposed to chemicals
D. In a damp environment

40. Which of the following is NOT a safe


work practice with hand tools?
A. Make sure the blade is locked
B. Cut away from your body
C. Hold the object to be cut in your hand
D. Wear safety gloves

41. A __________ is used to measure the


current flowing through a circuit.
A. Ammeter
B. Voltmeter
C. Ohmmeter
D. Multimeter

42. A __________ is a device used to protect


electrical equipment from overloads and
surges.
A. Fuse
B. Circuit breaker
C. Capacitor
D. Resistor

43. Before using electrical tools, always


inspect the __________ for any damages or
faults.
A. Cables
B. Handles
C. Plug connections
D. All of the above

44. A __________ is used to hold two metal


conductors together securely by melting
solder.
A. Soldering iron
B. Wire cutter
C. Clamp meter
D. Hammer
45. The _________ meter is an instrument
used to measure resistance in a circuit.
A. Digital
B. Analog
C. Multimeter
D. Ampermeter

46. What does the symbol of a capacitor


look like on a schematic diagram?
A. A long rectangle
B. A pair of parallel lines
C. A circle with a line
D. A square with dots

47. Which of the following components is


used to store electrical charge in a
circuit?
A. Diode
B. Resistor
C. Capacitor
D. Transistor

48. Which of these is a type of power


supply?
A. Battery
B. Capacitor
C. Diode
D. Resistor

49. Which of these components controls


the flow of electrical current in a circuit?
A. Switch
B. Battery
C. Wire
D. Capacitor

50. Which of these is used to insulate wires


in a circuit?
A. Copper
B. Rubber
C. Metal
D. Paper
Part 1: Multiple Choice

1. D. all of the above

2. A. preparing

3. A. Anti-static mat

4. C. Compressed air

5. B. planning

6. B. Lint-free cloth

7. A. recognition

8. C. safety

9. B. Utility Knife

10. C. Both A and B

Part 2: True or False

11. B. False

12. B. False

13. A. True

14. A. True

15. B. False

Part 3: Fill in the Blanks

16. equalize

17. clockwise

18. counterclockwise

19. Phillips
20. insulator

Part 4: Multiple Choice Questions

21. C. Digital multimeter

22. B. AC

23. A. Fuse

24. B. Non-metallic sheathed cable

25. A. Soldering iron

Part 5: Identification Questions

26. A. Digital multimeter

27. D. Leads

28. A. Zero adjustment knob

29. A. Function selector

30. A. Analog multimeter

31. A. Resistors

32. A. Color code system

33. B. Open capacitor

34. A. Step-up transformer

35. B. Step-down transformer

Part 6: Additional Multiple Choice Questions

36. B. Drill

37. A. Check the blade for wear

38. C. Always check for voltage before use

39. A. In a dry place

40. C. Hold the object to be cut in your


hand
Part 7: Fill in the Blanks

41. A. Ammeter

42. B. Circuit breaker

43. D. All of the above

44. A. Soldering iron

45. C. Multimeter

Part 8: Final Multiple Choice Questions

46. B. A pair of parallel lines

47. C. Capacitor

48. A. Battery

49. A. Switch

50. B. Rubber

You might also like