0% found this document useful (0 votes)
74 views3 pages

2023-Microcontroller & Embedded System Apr-May (AICTE)

Uploaded by

5z9tvj6g5q
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
74 views3 pages

2023-Microcontroller & Embedded System Apr-May (AICTE)

Uploaded by

5z9tvj6g5q
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

RAIPIJR. ( C .

G )

B.
C028513(028)
Tech. (Fifth Semester) Examination,
April-May 2023
(New Scheme)
(Electronics & Telecommunication Engg. Brancn)
MICROCONTROLLER & EMBEDDED SYSTEM
Time Allowed : Three hours

Maximum Marks : 100

Minimum Pass Marks : 35


Note : Attempt allquestions. Part (a) of each question
is compulsory and carries 4 marks each. Attempt
any two parts from (b), (c) and (d) of each
questions & carrying 8 marks each.
Unit-I

1. (a) Explain the structure of Internal RAM of 8051


Microcontroller. 4

(b) Draw thearchitecture of microcontroller 8051 and


explain the function of eachblock. 8

CO28513(028) PTO
| 31 generate
|2 | program to
BCD. Write a (d) Write an assembly language programming onpin
(c) Assume that register A has Packed
programn to convert packed BCD to two ASCII given square wave using time MHz.
XTAL = 12
PLl off 8051 controller.
number and place them into R2 and R6. 8

(d) Write a program to mOve the bytes fron Internal f-.-0.2mg-


<0.1mng->

50 cycles
RAM address from 3OH into External RAM address 100 cycles
from 4000 H. (Number of data bytes: 10). Unit-IJI
Registers. 4
Unit-II
Explain the function of SCON and SBUF
3. (a)
2. (a) Discuss the various timer modes supported by 8051. to interface
8051
What is special about the auto reload mode? 4 (b) Design a interfacing circuit MAX-
of PC using
Microcontroller with serial port
(b) Write a program to do the following: ofMAX-232 amd MAX
232. State the advantages 8
() Receive data serially and send it to PO. 233.
(11) Have port Pl read and transmit serially and
copy given to P2. (c) Explain the following standards :
(i) Make Timer 0 to generate square wave of RS 422, GPIB, RS 232
frequency 15 KHz on P 0-1. Use 8051 (a) Write a program to send the message serially
microcontroller and baud rate 4800. (XTAL = "CSVTU" with Baud Rate 9600 (XTAL 12 MHz).
1 0592 MHz)
Unit-IV
(c) Write an assembly language program to count l000
pulses externally connected to P 3-4 of 805 1and 4. (a) Interface 4x4 Matrix Keyboardwith 8051 Micro
controller. 4
after receiving all 1000 pulses, display 'OK' message
on display connected to the port P2. (b) ARobotic arm consist of twOstepper motors Mi
and M2 at two joints. Each motor has step angle
C0285 13(028) CO285 13(028) PT
|4|

degree, WriHs an.


hss 2
degree clockwis M2 by 24
At chockwis, Ue 4 slep wqsE, Coitecied
deree
MI with port ad M2 with Pon P2.
es lterfsre AX 004 wnh Mercontrollerad wed
ANserbly Language l'rogram lo read 10) dats brhes
lvom ADCand Storento Extenal pAM (30) H
onwords),

(d) Jnterlace the followng memory chips with 31


Microcontroller : Irogram ROM 32K /%, Data
RAM I6K /8, Data kOM l6KZ8

Unit-V

5. (a) Give the application of emhedect sytem in cons1T


clectronics with suitable diagram. 4

(b) What do you mcan embcdded system? Draw the


block diagram of cmbcded system and explain
hardware and soflware requiremcnt for designing of
cmbcddcd system. 8

(c) Explain designing parameters of an embedded


systems and its significances.
{d) Explain charactceristics or Real Time Embcdded
System. 8
180} CO28513(028)

You might also like