1/6/25, 1:02 AM U of A ANSYS Tutorials - Modelling Using Axisymmetry

This tutorial was completed using ANSYS 7.0 This tutorial is intended to outline the steps required to create an
axisymmetric model.

The model will be that of a closed tube made from steel. Point loads will be applied at the center of the top and
bottom plate to make an analytical verification simple to calculate. A 3/4 cross section view of the tube is
shown below.

As a warning, point loads will create discontinuities in the your model near the point of application. If you
chose to use these types of loads in your own modelling, be very careful and be sure to understand the theory of
how the FEA package is appling the load and the assumption it is making. In this case, we will only be
concerned about the stress distribution far from the point of application, so the discontinuities will have a
negligable effect.

1. Give example a Title

Utility Menu > File > Change Title ...

/title, Axisymmetric Tube

2. Open preprocessor menu

ANSYS Main Menu > Preprocessor

/PREP7

3. Create Areas

Preprocessor > Modeling > Create > Areas > Rectangle > By Dimensions
RECTNG,X1,X2,Y1,Y2

For an axisymmetric problem, ANSYS will rotate the area around the y-axis at x=0. Therefore, to
create the geometry mentioned above, we must define a U-shape.

We are going to define 3 overlapping rectangles as defined in the following table:

file:///F:/Old Hard Drive/FEA/ANSYS/Alberta/Intermediate/Modelling Using Axisymmetry.mht 1/7

1/6/25, 1:02 AM U of A ANSYS Tutorials - Modelling Using Axisymmetry

Rectangle X1 X2 Y1 Y2
1 0 20 0 5
2 15 20 0 100
3 0 20 95 100

4. Add Areas Together

Preprocessor > Modeling > Operate > Booleans > Add > Areas
AADD,ALL

Click the Pick All button to create a single area.

5. Define the Type of Element

Preprocessor > Element Type > Add/Edit/Delete...

For this problem we will use the PLANE2 (Structural, Solid, Triangle 6node) element. This
element has 2 degrees of freedom (translation along the X and Y axes).

Many elements support axisymmetry, however if the Ansys Elements Reference (which can be
found in the help file) does not discuss axisymmetric applications for a particular element type,
axisymmetry is not supported.

6. Turn on Axisymmetry

While the Element Types window is still open, click the Options... button.

Under Element behavior K3 select Axisymmetric.

7. Define Element Material Properties

Preprocessor > Material Props > Material Models > Structural > Linear > Elastic > Isotropic

In the window that appears, enter the following geometric properties for steel:

i. Young's modulus EX: 200000

ii. Poisson's Ratio PRXY: 0.3

8. Define Mesh Size

Preprocessor > Meshing > Size Cntrls > ManualSize > Areas > All Areas

For this example we will use an element edge length of 2mm.

9. Mesh the frame

Preprocessor > Meshing > Mesh > Areas > Free > click 'Pick All'
file:///F:/Old Hard Drive/FEA/ANSYS/Alberta/Intermediate/Modelling Using Axisymmetry.mht 2/7
1/6/25, 1:02 AM U of A ANSYS Tutorials - Modelling Using Axisymmetry

Your model should know look like this:

1. Define Analysis Type

Solution > Analysis Type > New Analysis > Static

ANTYPE,0

2. Apply Constraints
Solution > Define Loads > Apply > Structural > Displacement > Symmetry B.C. > On Lines

Pick the two edges on the left, at x=0, as shown below. By using the symmetry B.C. command,
ANSYS automatically calculates which DOF's should be constrained for the line of symmetry.
Since the element we are using only has 2 DOF's per node, we could have constrained the lines in
the x-direction to create the symmetric boundary conditions.

Utility Menu > Select > Entities

file:///F:/Old Hard Drive/FEA/ANSYS/Alberta/Intermediate/Modelling Using Axisymmetry.mht 3/7
1/6/25, 1:02 AM U of A ANSYS Tutorials - Modelling Using Axisymmetry

Select Nodes and By Location from the scroll down menus. Click Y coordinates and type 50 into
the input box as shown below, then click OK.

Solution > Define Loads > Apply > Structural > Displacement > On Nodes > Pick All

Constrain the nodes in the y-direction (UY). This is required to constrain the model in space,
otherwise it would be free to float up or down. The location to constrain the model in the y-
direction (y=50) was chosen because it is along a symmetry plane. Therefore, these nodes won't
move in the y-direction according to theory.

3. Utility Menu > Select > Entities

In the select entities window, click Sele All to reselect all nodes. It is important to always reselect all
entities once you've finished to ensure future commands are applied to the whole model and not just a
few entities. Once you've clicked Sele All, click on Cancel to close the window.

4. Apply Loads
Solution > Define Loads > Apply > Structural > Force/Moment > On Keypoints
Pick the top left corner of the area and click OK. Apply a load of 100 in the FY direction.

Solution > Define Loads > Apply > Structural > Force/Moment > On Keypoints
Pick the bottom left corner of the area and click OK. Apply a load of -100 in the FY direction.

The applied loads and constraints should now appear as shown in the figure below.

file:///F:/Old Hard Drive/FEA/ANSYS/Alberta/Intermediate/Modelling Using Axisymmetry.mht 4/7

1/6/25, 1:02 AM U of A ANSYS Tutorials - Modelling Using Axisymmetry

5. Solve the System

Solution > Solve > Current LS

SOLVE

1. Hand Calculations

Hand calculations were performed to verify the solution found using ANSYS:

The stress across the thickness at y = 50mm is 0.182 MPa.

2. Determine the Stress Through the Thickness of the Tube

Utility Menu > Select > Entities...

Select Nodes > By Location > Y coordinates and type 45,55 in the Min,Max box, as shown below
and click OK.

file:///F:/Old Hard Drive/FEA/ANSYS/Alberta/Intermediate/Modelling Using Axisymmetry.mht 5/7

1/6/25, 1:02 AM U of A ANSYS Tutorials - Modelling Using Axisymmetry

General Postproc > List Results > Nodal Solution > Stress > Components SCOMP

The following list should pop up.

If you take the average of the stress in the y-direction over the thickness of the tube, (0.18552 +
0.17866)/2, the stress in the tube is 0.182 MPa, matching the analytical solution. The average is
used because in the analytical case, it is assumed the stress is evenly distributed across the
thickness. This is only true when the location is far from any stress concentrators, such as corners.
Thus, to approximate the analytical solution, we must average the stress over the thickness.

3. Plotting the Elements as Axisymmetric

Utility Menu > PlotCtrls > Style > Symmetry Expansion > 2-D Axi-symmetric...

The following window will appear. By clicking on 3/4 expansion you can produce the figure
shown at the beginning of this tutorial.

file:///F:/Old Hard Drive/FEA/ANSYS/Alberta/Intermediate/Modelling Using Axisymmetry.mht 6/7

1/6/25, 1:02 AM U of A ANSYS Tutorials - Modelling Using Axisymmetry

4. Extra Exercise

It is educational to repeat this tutorial, but leave out the key option which enables axisymmetric
modelling. The rest of the commands remain the same. If this is done, the model is a flat, rectangular
plate, with a rectangular hole in the middle. Both the stress distribution and deformed shape change
drastically, as expected due to the change in geometry. Thus, when using axisymmetry be sure to verify
the solutions you get are reasonable to ensure the model is infact axisymmetric.

The above example was solved using a mixture of the Graphical User Interface (or GUI) and the command
language interface of ANSYS. This problem has also been solved using the ANSYS command language
interface that you may want to browse. Open the .HTML version, copy and paste the code into Notepad or a
similar text editor and save it to your computer. Now go to 'File > Read input from...' and select the file. A
.PDF version is also available for printing.

file:///F:/Old Hard Drive/FEA/ANSYS/Alberta/Intermediate/Modelling Using Axisymmetry.mht 7/7