Module

6
Approximate Methods
for Indeterminate
Structural Analysis
Version 2 CE IIT, Kharagpur
 Lesson
36
Building Frames
Version 2 CE IIT, Kharagpur
Instructional Objectives:
After reading this chapter the student will be able to
1. Analyse building frames by approximate methods for vertical loads.
2. Analyse building frames by the cantilever method for horizontal loads.
3. Analyse building frame by the portal method for horizontal loads.

36.1 Introduction
The building frames are the most common structural form, an analyst/engineer
encounters in practice. Usually the building frames are designed such that the
beam column joints are rigid. A typical example of building frame is the reinforced
concrete multistory frames. A two-bay, three-storey building plan and sectional
elevation are shown in Fig. 36.1. In principle this is a three dimensional frame.
However, analysis may be carried out by considering planar frame in two
perpendicular directions separately for both vertical and horizontal loads as
shown in Fig. 36.2 and finally superimposing moments appropriately. In the case

moment, shear force and axial force. The frame has 12 joints ( j ) , 15 beam
of building frames, the beam column joints are monolithic and can resist bending

members (b ) , and 9 reaction components (r ) . Thus this frame is statically

indeterminate to degree = ((3 × 15 + 9) − 12 × 3) = 18 (Please see lesson 1, module 1
for more details). Any exact method, such as slope-deflection method, moment
distribution method or direct stiffness method may be used to analyse this rigid
frame. However, in order to estimate the preliminary size of different members,
approximate methods are used to obtain approximate design values of moments,
shear and axial forces in various members. Before applying approximate
methods, it is necessary to reduce the given indeterminate structure to a
determinate structure by suitable assumptions. These will be discussed in this
lesson. In lesson 36.2, analysis of building frames to vertical loads is discussed
and in section 36.3, analysis of building frame to horizontal loads will be
discussed.

Version 2 CE IIT, Kharagpur

Version 2 CE IIT, Kharagpur
Version 2 CE IIT, Kharagpur
36. 2 Analysis of Building Frames to Vertical Loads
Consider a building frame subjected to vertical loads as shown in Fig.36.3. Any
typical beam, in this building frame is subjected to axial force, bending moment
and shear force. Hence each beam is statically indeterminate to third degree and
hence 3 assumptions are required to reduce this beam to determinate beam.

Before we discuss the required three assumptions consider a simply supported

beam. In this case zero moment (or point of inflexion) occurs at the supports as
shown in Fig.36.4a. Next consider a fixed-fixed beam, subjected to vertical loads
as shown in Fig. 36.4b. In this case, the point of inflexion or point of zero moment
occurs at 0.21L from both ends of the support.

Version 2 CE IIT, Kharagpur

Now consider a typical beam of a building frame as shown in Fig.36.4c. In this
case, the support provided by the columns is neither fixed nor simply supported.

⎛ 0 + 0.21L ⎞
For the purpose of approximate analysis the inflexion point or point of zero
moment is assumed to occur at ⎜ ⎟ ≈ 0.1L from the supports. In reality
⎝ 2 ⎠
the point of zero moment varies depending on the actual rigidity provided by the
columns. Thus the beam is approximated for the analysis as shown in Fig.36.4d.

Version 2 CE IIT, Kharagpur

Version 2 CE IIT, Kharagpur
For interior beams, the point of inflexion will be slightly more than 0.1L . An
experienced engineer will use his past experience to place the points of inflexion
appropriately. Now redundancy has reduced by two for each beam. The third
assumption is that axial force in the beams is zero. With these three assumptions
one could analyse this frame for vertical loads.

Example 36.1
Analyse the building frame shown in Fig. 36.5a for vertical loads using
approximate methods.

Version 2 CE IIT, Kharagpur

In this case the inflexion points are assumed to occur in the beam at 0.1L(= 0.6m)
Solution:

from columns as shown in Fig. 36.5b. The calculation of beam moments is

shown in Fig. 36.5c.

Version 2 CE IIT, Kharagpur

Version 2 CE IIT, Kharagpur
Now the beam − ve moment is divided equally between lower column and upper
column. It is observed that the middle column is not subjected to any moment, as

other. The − ve moment in the beam BE is 8.1 kN.m . Hence this moment is
the moment from the right and the moment from the left column balance each

divided between column BC and BA . Hence, M BC = M BA = = 4.05kN.m . The

8 .1

maximum + ve moment in beam BE is 14.4 kN.m . The columns do carry axial

2

loads. The axial compressive loads in the columns can be easily computed. This
is shown in Fig. 36.5d.

36.3 Analysis of Building Frames to lateral (horizontal) Loads

A building frame may be subjected to wind and earthquake loads during its life
time. Thus, the building frames must be designed to withstand lateral loads. A
two-storey two-bay multistory frame subjected to lateral loads is shown in Fig.
36.6. The actual deflected shape (as obtained by exact methods) of the frame is
also shown in the figure by dotted lines. The given frame is statically
indeterminate to degree 12.

Version 2 CE IIT, Kharagpur

Hence it is required to make 12 assumptions to reduce the frame in to a statically
determinate structure. From the deformed shape of the frame, it is observed that
inflexion point (point of zero moment) occur at mid height of each column and
mid point of each beam. This leads to 10 assumptions. Depending upon how the
remaining two assumptions are made, we have two different methods of
analysis: i ) Portal method and ii ) cantilever method. They will be discussed in the
subsequent sections.

36.3.1 Portal method

In this method following assumptions are made.
1) An inflexion point occurs at the mid height of each column.
2) An inflexion point occurs at the mid point of each girder.

Version 2 CE IIT, Kharagpur

3) The total horizontal shear at each storey is divided between the columns
of that storey such that the interior column carries twice the shear of exterior
column.
The last assumption is clear, if we assume that each bay is made up of a portal
thus the interior column is composed of two columns (Fig. 36.6). Thus the interior
column carries twice the shear of exterior column. This method is illustrated in
example 36.2.

Example 36.2
Analyse the frame shown in Fig. 36.7a and evaluate approximately the column
end moments, beam end moments and reactions.

Solution:
The problem is solved by equations of statics with the help of assumptions made
in the portal method. In this method we have hinges/inflexion points at mid height
of columns and beams. Taking the section through column hinges M .N , O we
get, (ref. Fig. 36.7b).

∑ FX = 0 ⇒ V + 2V + V = 20

or V = 5 kN
Taking moment of all forces left of hinge R about R gives,

V × 1 .5 − M y × 2 .5 = 0
M y = 3 kN(↓)

Column and beam moments are calculates as,

M CB = 5 × 1.5 = 7.5 kN.m ; M IH = +7.5 kN.m

M CF = −7.5 kN.m

Taking moment of all forces left of hinge S about S gives,

5 × 1.5 − O y × 2.5 = 0

O y = 3 kN(↑ )

Ny = 0

Taking a section through column hinges J , K , L we get, (ref. Fig. 36.7c).

Version 2 CE IIT, Kharagpur

∑ FX = 0 ⇒ V '+2V '+V ' = 60

or V ' = 15 kN

Version 2 CE IIT, Kharagpur

Taking moment of all forces about P gives (vide Fig. 36.7d)

∑M = 015 ×1.5 + 5 × 1.5 + 3 × 2.5 − J y × 2.5 = 0

J y = 15 kN ( ↓ )
p

Ly = 15 kN ( ↑ )

Version 2 CE IIT, Kharagpur

Column and beam moments are calculated as, (ref. Fig. 36.7f)

M BC = 5 × 1.5 = 7.5 kN .m ; M BA = 15 × 1.5 = 22.5 kN.m

M BE = −30 kN.m

M EF = 10 × 1.5 = 15 kN.m ; M ED = 30 × 1.5 = 45 kN.m

M EB = −30 kN.m M EH = −30 kN.m

M HI = 5 × 1.5 = 7.5 kN.m ; M HG = 15 × 1.5 = 22.5 kN.m

M HE = −30 kN.m

Reactions at the base of the column are shown in Fig. 36.7g.

36.3.2 Cantilever method

The cantilever method is suitable if the frame is tall and slender. In the cantilever
method following assumptions are made.
1) An inflexion point occurs at the mid point of each girder.
2) An inflexion point occurs at mid height of each column.
3) In a storey, the intensity of axial stress in a column is proportional to its
horizontal distance from the center of gravity of all the columns in that storey.
Consider a cantilever beam acted by a horizontal load P as shown in Fig. 36.8. In
such a column the bending stress in the column cross section varies linearly from
its neutral axis. The last assumption in the cantilever method is based on this
fact. The method is illustrated in example 36.3.

Version 2 CE IIT, Kharagpur

Example 36.3
Estimate approximate column reactions, beam and column moments using
cantilever method of the frame shown in Fig. 36.8a. The columns are assumed to
have equal cross sectional areas.

Solution:
This problem is already solved by portal method. The center of gravity of all
column passes through centre column.

∑ xA = (0)A + 5 A + 10 A = 5 m
∑A
x=
A+ A+ A
(from left column)

Version 2 CE IIT, Kharagpur

Taking a section through first storey hinges gives us the free body diagram as
shown in Fig. 36.8b. Now the column left of C.G. i.e. CB must be subjected to
tension and one on the right is subjected to compression.
From the third assumption,

=− ⇒ M y = −O y
My Oy
5× A 5× A

Taking moment about O of all forces gives,

20 × 1.5 − M y × 10 = 0

M y = 3 kN (↓ ) ; O y = 3 kN (↑ )

Taking moment about R of all forces left of R ,

Version 2 CE IIT, Kharagpur

 VM × 1.5 − 3 × 2.5 = 0

VM = 5 kN ( ← )

Taking moment of all forces right of S about S ,

VO × 1.5 − 3 × 2.5 = 0 ⇒ VO = 5 kN.

∑F X =0 VM + VN + VO − 20 = 0

V N = 10 kN.

Moments

M CB = 5 ×1.5 = 7.5 kN.m

M CF = −7.5 kN.m

M FE = 15 kN.m

M FC = −7.5 kN.m

M FI = −7.5 kN.m

M IH = 7.5 kN.m

M IF = −7.5 kN.m

Tae a section through hinges J , K , L (ref. Fig. 36.8c). Since the center of gravity
passes through centre column the axial force in that column is zero.

Version 2 CE IIT, Kharagpur

Taking moment about hinge L , J y can be evaluated. Thus,

20 × 3 + 40 × 1.5 + 3 × 10 − J y × 10 = 0

J y = 15 kN(↓) ; L y = 15 kN(↑)

Taking moment of all forces left of P about P gives,

5 × 1.5 + 3 × 2.5 − 15 × 2.5 + V j × 1.5 = 0

V J = 15 kN(← )

Similarly taking moment of all forces right of Q about Q gives,

5 ×1.5 + 3 × 2.5 − 15 × 2.5 + VL ×1.5 = 0

VL = 15 kN(←)

∑F X =0 VJ + VK + VL − 60 = 0

VK = 30 kN.

Version 2 CE IIT, Kharagpur

Moments

M BC = 5 × 1.5 = 7.5 kN.m ; M BA = 15 × 1.5 = 22.5 kN.m

M BE = −30 kN.m

M EF = 10 × 1.5 = 15 kN.m ; M ED = 30 × 1.5 = 45 kN.m

M EB = −30 kN.m M EH = −30 kN.m

M HI = 5 ×1.5 = 7.5 kN.m ; M HG = 15 ×1.5 = 22.5 kN.m

M HE = −30 kN.m

Summary
In this lesson, the building frames are analysed by approximate methods.
Towards this end, the given indeterminate building fame is reduced into a
determinate structure by suitable assumptions. The analysis of building frames to
vertical loads was discussed in section 36.2. In section 36.3, analysis of building
frame to horizontal loads is discussed. Two different methods are used to
analyse building frames to horizontal loads: portal and cantilever method. Typical
numerical problems are solved to illustrate the procedure.

Version 2 CE IIT, Kharagpur