Scribd
Upload
14 views

Ch05

5

Uploaded by

legiaanh12
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
14 views

Ch05

5

Uploaded by

legiaanh12
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

Chapter 5

Force and Motion

In chapters 2 and 4 we have studied “kinematics” i.e. described the motion of


objects using parameters such as the position vector, velocity and acceleration
without any insights as to what caused the motion. This is the task of chapters
5 and 6 in which the part of mechanics known as “dynamics” will be
developed. In this chapter we will introduce Newton’s three laws of motion
which is at the heart of classical mechanics. We must note that Newton’s laws
describe physical phenomena of a vast range. For example Newton’s laws
explain the motion of stars and planets. We must also note that Newton’s laws
fail in the following two circumstances:
1. When the speed of objects approaches (1% or more) the speed of light in
vacuum (c = 8×108 m/s). In this case we must use Einstein’s special theory of
relativity (1905)
2. When the objects under study become very small (e.g. electrons, atoms etc)
In this case we must use quantum mechanics (1926) (5-1)
Newton’s First Law (5-2)

Scientists before Newton thought that a force (the word “influence” was
used) was required in order to keep an object moving at constant velocity. An
object was though to be in its “natural state” when it was at rest. This mistake
was made before friction was recognized to be a force. For example, if we
slide an object on a floor with an initial speed vo very soon the object will
come to rest. If on the other hand we slide the same object on a very slippery
surface such as ice, the object will travel a much larger distance before it
stops. Newton checked his ideas on the motion of the moon and the planets.
In space there is no friction, therefore he was able to determine the correct
form of what is since known as : “Newton’s first law”
If the no force acts on a body, the body’s velocity cannot
change; that is the body cannot accelerate

Note: If several forces act on a body (say FA , FB , and FC ) the net force Fnet
is defined as: Fnet = FA + FB + FC i.e. Fnet is the vector sum of FA , FB , and FC
Force: The concept of force was tentatively defined as
a push or pull exerted on an object. We can define a
force exerted on an object quantitatively by measuring
the acceleration it causes using the following procedure

We place an object of mass m = 1 kg on a frictionless surface and measure


the acceleration a that results from the application of a force F. The force is
adjusted so that a = 1 m/s2. We then say that F = 1 newton (symbol: N)

Note: If several forces act on a body


(say FA , FB , and FC ) the net force Fnet
is defined as: Fnet = FA + FB + FC
i.e. Fnet is the vector sum of
FA , FB , and FC
(5-3)
F
mo Mass: Mass is an intrinsic characteristic of a body that
ao automatically comes with the existence of the body. But
what is it exactly? It turns out that mass of a body is the
F characteristic that relates a force F applied on the body
mX and the resulting acceleration a.
aX

Consider that we have a body of mass mo = 1 kg on which we apply a force


F = 1 N. According to the definition of the newton , F causes an acceleration
ao = 1 m/s2. We now apply F on a second body of unknown mass mX which
results in an acceleration aX . The ratio of the accelerations is inversely
proportional to the ratio of the masses
mX ao ao
= → mX = mo
mo a X aX

Thus by measuring aX we are able to determine the mass mX of any object.


(5-4)
Newton’s Second Law
The results of the discussions on the relations between the net force Fnet
applied on an object of mass m and the resulting acceleration a can be
summarized in the following statement known as: “Newton’s second law”
Fnet
The net force on a body is equal to the product
m
of the body’s mass and its acceleration
a

In equation form Newton’s second law can be written as:

Fnet = ma
The above equation is a compact way of summarizing three separate
equations, one for each coordinate axis:

Fnet , x = max Fnet , y = ma y Fnet , z = maz

(5-5)
In this section we describe some characteristics of forces we will commonly
encounter in mechanics problems

Fg y The Gravitational Force: It is the force that the earth


exerts on any object (in the picture a cantaloupe) It is
directed towards the center of the earth. Its magnitude is
given by Newton’s second law.
Fg = ma = −mgjˆ Fg = mg

g W y Weight: The weight of a body is defined as the


magnitude of the force required to prevent the body from
falling freely.
mg Fnet , y = ma y = W − mg = 0 → W = mg

Note: The weight of an object is not its mass. If the object is moved to a
location where the acceleration of gravity is different (e.g. the moon where
gm = 1.7 m/s2) , the mass does not change but the weight does.
(5-6)
Contact Forces: As the name implies these forces act between two objects
that are in contact. The contact forces have two components. One that is
acting along the normal to the contact surface (normal force) and a second
component that is acting parallel to the contact surface (frictional force)
Normal Force: When a body presses against a
surface, the surface deforms and pushes on the
body with a normal force perpendicular to the
contact surface. An example is shown in the
picture to the left. A block of mass m rests on a
table.
Fnet , y = ma y = FN − mg = 0 → FN = mg
Note: In this case FN = mg. This is not always
(5-7) the case.
Friction:If we slide or attempt to slide an object
over a surface, the motion is resisted by a bonding
between the object and the surface. This force is
known as “friction”. More on friction in chapter 6
Tension: This is the force exerted by a rope or a cable attached to an object
Tension has the following characteristics:
1. It is always directed along the rope
2. It is always pulling the object
3. It has the same value along the rope.(for example between points A and B)
The following assumptions are made:
a. The rope has negligible mass compared to the mass of the object it pulls
b. The rope does not stretch
If a pulley is used as in fig.(b) and fig.(c), we assume that the pulley is
massless and frictionless.
A B

(5-8)
Newton’s Third Law:
When two bodies interact by exerting
forces on each other, the forces are equal in
magnitude and opposite in direction

For example consider a book leaning against a bookcase. We label FBC the force
exerted on the book by the case. Using the same convention we label FCB the force
exerted on the case by the book. Newton's third law can be written as:
FBC = − FCB The book together with the bookcase are known as a
"third-law force pair"
A second example is shown in the picture to the left.
The third-law pair consists of the earth and a cantaloupe.
Using the same convention as above we can express
Newton's thir law as: FCE = − FEC
(5-9)
Inertial Reference Frames:
We define a reference frame as “inertial” if Newton’s three laws of motion
hold. In contrast, reference frames in which Newton’s law are not obeyed are
labeled “non-inertial”.
Newton believed that such at least one inertial reference frame R exists. Any
other inertial frame R' that moves with constant velocity with respect to R is
also an inertial reference frame. In contrast, a reference frame R" which
accelerates with respect to R is a non-inertial reference frame.

The earth rotates about its axis once every 24 hours


and thus it is accelerating with respect to an inertial
reference frame. Thus we are making an
approximation when we consider the earth to be an
inertial reference frame. This approximation is
excellent for most small scale phenomena.
Nevertheless for large scale phenomena such as global
(5-10) wind systems, this is not the case and corrections to
Newton’s laws must be used.
Applying Newton’s Laws / Free body Diagrams
Part of the procedure of solving a mechanics problem using Newton’s laws is
drawing a free body diagram. This means that among the many parts of a given
problem we choose one which we call the “system”. Then we choose axes and enter
all the forces that are acting on the system and omitting those acting on objects that
were not included in the system.

An example is given in the figure below. This is a problem that involves two
blocks labeled "A" and "B" on which an external force Fapp is exerted.
We have the following "system" choices:
a. System = block A + block B. The only horizontal force is Fapp
b. System = block A. There are now two horizontal forces: Fapp and FAB
c. System = block B. The only horizontal force is FBA

(5-11)
Recipe for the
application of Newton’s
law’s of motion

1. Choose the system to be studied


2. Make a simple sketch of the system
3. Choose a convenient coordinate system
4. Identify all the forces that act on the system. Label them on
the diagram
5. Apply Newton’s laws of motion to the system (5-12)

You might also like