Scribd
Upload
26 views5 pages

Unit IV - Introduction To Proteus

Uploaded by

singhchamanjeet47
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
26 views5 pages

Unit IV - Introduction To Proteus

Uploaded by

singhchamanjeet47
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

ELSEC351: Paper X- Electronic Design Automation Tools

Unit IV- Introduction to Proteus


1. PROTEUS
Proteus PCB Design and Simulation Software
Introduction
Proteus is a simulation and design software tool
developed by Labcenter Electronics for Electrical
and Electronic circuit design.
About Proteus:
It is a software suite containing schematic,
simulation as well as PCB designing.
 ISIS is the software used to draw schematics
and simulate the circuits in real time. The
simulation allows human access during run
time, thus providing realtime simulation.
 ARES is used for PCB designing. It has the
feature of viewing output in 3Dview of the
designed PCB along with components.
 The designer can also develop 2D drawings
for the product.

Starting New Design


Step 1: Open ISIS software and select new design
in File menu
Step 2: A dialogue box appears to save the
current design. However, we are creating a new
design file so you can click Yes or No depending
on the content of the present file. Then a Pop-Up
appears asking to select the template. It is similar
to selecting the paper size while printing. For now
select default or according to the layout size of
the circuit. Proteus Default Template Select
Step 3: An untitled design sheet will be opened, save it according to your wish,
it is better to create a new folder for every layout as it generates other files
supporting your design. However, it is not mandatory.
Step 4: To select components, Click on the
component mode button.
Step 5: Click on Pick from Libraries. It shows
the categories of components available and a
search option to enter the part name.
Step 6: Select the components from categories
or type the part name in Keywords text box.
Step 7: The selected components will appear in
the devices list. Select the component and place
it in the design sheet by left-click.
Place all the required components and route the
wires i. e, make connections. Either selection
mode above the component mode or component
mode allows to connect through wires. Left click
from one terminal to other to make connection.
Double right-click on the connected wire or the
component to remove connection or the
component respectively.
Component Properties Selection- Double click
on the component to edit the properties of the
components and click on Ok.
Step 8: After connecting the circuit, click on the
play button to run the simulation.
In this example simulation, the button is depressed
during simulation by clicking on it to make LED
glow. Simulation can be stepped, paused or
stopped at any time.
Simulation of Active Low Pass Filter:

U1

7
R1 3
+ A
6
47k
C1 2
B
0.022uF
- C

4
1
5
AM FM
741
D

GND
GND

O/P below cut off frequency:

O/P above cut off frequency:


Simulation of Active High Pass Filter:

C1 U1

7
3
+ A
0.022uF R1 6
47k 2
B

- C

4
1
5
AM FM
741
D

GND
GND

O/P below cut off frequency

O/P above cut off frequency


Simulation of Wein Bridge Oscillator

RV2

100%
RV1
1k

99%
BAT1
15V
C2
0.1uF 2k U1

7
A
3
B
6
2
C

C1 R2 D

4
1
5
0.01uF 1k R1 741
100

BAT2
15V

GND

You might also like