VISVESVARAYA TECHNOLOGICAL UNIVERSITY

BELGAVI, KARNATAKA

“TITLE OF THE PROJECT”

A Report
Submitted in partial fulfilment for the award of degree
Of
Bachelor of Engineering
In

ELECTRONCS AND COMMUNICATIONS ENGINEERING

By

NAME1 (USN)
NAME2 (USN)
NAME3 (USN)
NAME4 (USN)

Under the guidance of

Internal External ( if applicable)

Guide Name Guide Name
Designation Designation
NIEIT, Mysuru-18 Affiliation

DEPARTMENT OF ELECTRONICS AND COMMUNICATIONS

ENGINEERING
THE NATIONAL INSTITUTE OF ENGINEERING
MYSURU-570008

2023-2024
TITLE OF THE PROJECT

THE NATIONAL INSTITUTE OF ENGINEERING

Mananthawadi Road
Mysuru-08

DEPARTMENT
OF
------------------------------------------ ENGINEERING

CERTIFICATE

Certified that the project work entitled ………………………………………………... carried

out by Mr./Ms. ………………………….……………….., USN…………………..………, a
bonafide student of …………………………………….in partial fulfillment for the award of
Bachelor of Engineering in ……………………………...………………………….………
of the Visvesvaraya Technological University, Belgaum during the year
……………………... It is certified that all corrections/suggestions indicated for Internal
Assessment have been incorporated in the Report deposited in the departmental library. The
project report has been approved as it satisfies the academic requirements in respect of Project
work prescribed for the said Degree.

Name & Signature of the Guide Name Signature of the HOD Signature of the Principal

External Viva

Name of the examiners Signature with date

1.

2.

Dept. of ECE, NIE, Mysore-08 Page 4

TITLE OF THE PROJECT

UNDERTAKING

I, ___________, HEREBY UNDERTAKE THAT THE PROJECT WORK ENTITLED

“__________________________________________” ISCARRIED OUT BY ME

INDEPENDENTLY UNDER THE GUIDANCE OF ___________________, _________,

DEPARTMENT OF -----------------------------------------------, NIE, MYSURU-08, IN PARTIAL

FULFILLMENT OF THE REQUIREMENT FOR THE AWARD OF BACHELOR OF

ENGINEERING IN ------------------------------------------------ BY THE VISVESVARAYA

TECHNOLOGICAL UNIVERSITY, BELGAUM. THE PROJECT HAS BEEN MY ORIGINAL WORK AND

HAS NOT FORMED THE BASIS FOR THE AWARD OF ANY DEGREE , ASSOCIATE SHIP, FELLOWSHIP

OR ANY OTHER SIMILAR TITLES.

SIGNATURE OF STUDENT

Dept. of ECE, NIE, Mysore-08 Page 5

TITLE OF THE PROJECT

Project Report Guidelines

CHAPTER 1 INTRODUCTION must include
1. Introduction (2-5pages)

2. Scope of proposed work/ Problem Statement (1-3pages)

3. Literature Survey/ Related Work (Should be an extensive

literature survey) (5-10 Pages with all the below subheading
included)
i) Cite and mention about the previous state of art
work done on the similar problem
ii) Comparison of methodology, System model, tool,
algorithm , metrics used in the previous work.
Comparison can be in the form of table to get better
clarity. Example is as below.

iii) Gap in the existing research

4. Motivation behind the proposed work (1 Page)

5. Organization of the Report (1 short Para is sufficient)

Dept. of ECE, NIE, Mysore-08 Page 6

TITLE OF THE PROJECT

CHAPTER 2 SYSTEM ANALYSIS must include

1. Introduction

2. Problem Definition/Framework

3. Proposed Methodology/Design Methodology(Block Diagrams,

Theoretical Derivations, Equations....)

4. Method of Analysis
**Hardware projects must include: the component layout,
complete circuit with the component list containing the name of
the component, numbers used, etc.

5. Conclusion

CHAPTER 3 SYSTEM DESIGN must include

1. Introduction

2. Detailed Design

3. Conclusions

CHAPTER 4 SYSTEM DESIGN IMPLEMENTATION

must include
1. Introduction

2. Implementation of Proposed Methodology

3. Developed Modules/Algorithms/Hardware tools/Software tools

and its application.

4. Conclusions

Dept. of ECE, NIE, Mysore-08 Page 7

TITLE OF THE PROJECT

Chapter 5 TESTING and RESULTS must include

1. Test Cases

2. Testing Methodologies

3. Results and Discussions for Each Test Case

4. Tabulation of Results

5. Conclusions

CONCLUSION WITH FUTURE ENHANCEMENTS

Publication Details
1. Front page of the paper prepared (or)

2. Presentation certificate/ Submission email confirmation (or

3. If published, details of publication

4. Funding details if any

BIBLIOGRAPHY

Relevant to project work comprising of

1. Technical paper References

2. Web references

3. Books references.

APPENDIX (if any)

1. Abbreviations (if any)

2. Hardware Component Data sheets ….(if any)

3. Data sheets of Test Cases etc...(if any)

4. Budget of project

Dept. of ECE, NIE, Mysore-08 Page 8

TITLE OF THE PROJECT

FONT STYLE and SIZE

INTRODUCTION/ABSTRACT # (font size 16)
SUB- SECTION #. SUB-SECTION HEADING (font size 14)
Body or the text of the synopsis (font size 12)

The figures and tables must be numbered chapter wise for e.g.: Fig. 2.1 Block diagram of a
serial binary adder, Table 3.1 Primitive flow table, etc.

1. ARRANGEMENT OF CONTENTS:
The sequence in which the project report material should be
arranged and bound should be as follows:

1. Cover Page
2. Inner Title Page
3. Bonafide Certificate
4. Bonafide Certificate issued at the Organization where the
project was carried out(If Applicable)
5. Undertaking
6. Acknowledgements
7. Abstract
8. Table of Contents
9. List of Tables
10.List of Figures
11.List of Symbols, Abbreviations and Nomenclature
12.Chapters
13.Publication Details
14.Plagiarism (less than 30 percent)
15.Appendix
16.References

Table of Contents – The table of contents should list all material

following it as well as any material which precedes it. The title page and
Bonafide Certificate will not find a place among the items listed in the
Table of Contents but the page numbers of which are in lower case
Roman letters. One and a half spacing should be adopted for typing the
matter under this head.

Dept. of ECE, NIE, Mysore-08 Page 9

TITLE OF THE PROJECT

List of Tables – The list should use exactly the same captions as they
appear above the tables in the text. One and a half spacing should be
adopted for typing the matter under this head.

List of Figures – The list should use exactly the same captions as they
appear below the figures in the text. One and a half spacing should be
adopted for typing the matter under this head.

List of Symbols, Abbreviations and Nomenclature – One and a half

spacing should be adopted or typing the matter under this head. Standard
symbols, abbreviations etc. should be used.

Chapters – The chapters may be broadly divided into 3 parts (i)

Introductory chapter, (ii) Chapters developing the main theme of the
project work (iii) and Conclusion.

The main text will be divided into several chapters and each
chapter may be further divided into several divisions and sub-divisions.

❖ Each chapter should be given an appropriate title.

❖ Tables and figures in a chapter should be placed in the

immediate vicinity of the reference where they are cited.

❖ Footnotes should be used sparingly. They should be typed

single space and placed directly underneath in the very same
page, which refers to the material they annotate.

Appendices – Appendices are provided to give supplementary

information, which is included in the main text may serve as a distraction
and cloud the central theme.

● Appendices should be numbered using Arabic numerals, e.g.

Appendix 1, Appendix 2, etc.

● Appendices, Tables and References appearing in appendices

should be numbered and referred to at appropriate places just
as in the case of chapters.
Dept. of ECE, NIE, Mysore-08 Page 10
TITLE OF THE PROJECT

● Appendices shall carry the title of the work reported and the
same title shall be made in the contents page also.

List of References –The listing of references should be typed 4 spaces

below the heading “REFERENCES” in citation order in single spacing
left – justified. The reference material should be listed in the citation
order. The name of the author/authors should be immediately followed by
the year and other details.

Table and figures - By the word Table, is meant tabulated numerical

data in the body of the project report as well as in the appendices. All
other non-verbal materials used in the body of the project work and
appendices such as charts, graphs, maps, photographs and diagrams may
be designated as figures.

Dept. of ECE, NIE, Mysore-08 Page 11