Bcu Operator Display
Bcu Operator Display
BMTW-SVU02C-EN
BMTW-SVU02C-EN
June 2006
This guide and the information in it are the property of American Standard Inc. and may not be used or reproduced in whole or in part,
without the written permission of American Standard Inc. Trane has a policy of continuous product improvement, and reserves the
right to change design and specification without notice.
Use of the software contained in this package is provided under a software license agreement. Unauthorized use of the software or
related materials discussed in this manual can result in civil damages and criminal penalties. The terms of this license are included
with the compact disk. Please read them thoroughly.
Although Trane has tested the described in this guide, no guarantee is offered that the hardware and software are error free.
Trane reserves the right to revise this publication at any time and to make changes to its content without obligation to notify any per-
son of such revision or change.
Trane may have patents or pending patent applications covering items in this publication. By providing this document, Trane does not
imply giving license to these patents.
™® The following are trademarks or registered trademarks of Trane: Tracer Summit and Trane
™® The following are trademarks or registered trademarks of their respective companies or organizations: Windows from
Microsoft Corporation.
BMTW-SVU02C-EN
nWARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
nCAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
It may also be used to alert against unsafe practices.
CAUTION
Indicates a situation that may result in equipment or property-damage-only accidents.
The following format and symbol conventions appear at appropriate locations throughout this manual:
IMPORTANT
Alerts installer, servicer, or operator to potential actions that could cause the product or system to
operate improperly but will not likely result in potential for damage
Note:
A note may be used to make the reader aware of useful information, to clarify a point, or to describe
options or alternatives.
BMTW-SVU02C-EN
BMTW-SVU02C-EN i
ii BMTW-SVU02C-EN
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
BMTW-SVU02C-EN iii
iv BMTW-SVU02C-EN
The BCU operator display is a liquid crystal display (LCD) touch screen.
It is installed in Tracer Summit BMTW building control units (BCUs) as
an option (see Figure 1). The operator-display touch screen enables you to
perform most of the Tracer Summit PC Workstation daily activities at the
BCU. The Tracer Summit workstation is the PC software program that
enables you to control and monitor the operation of HVAC equipment in
your building.
From the operator-display touch screen you can perform the following
tasks:
• View and manage alarms and events
• View and change setpoints
• Override schedules and equipment
• Modify schedule start times and stop times
• Maintain and calibrate the display
Operator-display
touch screen
BMTW BCU
BMTW-SVU02C-EN 1
Home Screen
The home screen is where each operator display task begins. It includes
five task buttons: View, Alarms, Schedule, Timed Override, and Setup
(see Figure 2). These buttons enable you to access system status informa-
tion for a particular task. Table 1 on page 3 briefly describes the function
of each button.
Note:
You may not have access to all of the tasks presented in this
guide. Your access privileges depend on your user profile. Con-
tact your supervisor for information.
Task
buttons
2 BMTW-SVU02C-EN
Button Description
For detailed information about using the View function, see “Viewing and Changing
System Status Information”on page 9.
For detailed information about Alarm tasks, see “Handling Alarms and Events” on
page 27.
Press the Schedule button to:
• View schedules
• Change schedule start times and stop times
• Delete exception schedules
• Create exceptions
For detailed information about Scheduling tasks, see “Displaying and Editing Sched-
ules” on page 31.
Press the Timed Override button to:
• Start a timed override
• Cancel a timed override
For detailed information about Override tasks, see “Making a Timed Override
Request” on page 47.
Press the Setup button to:
• Change either system time or date
• Adjust screen brightness and contrast
• Calibrate the operator-display touch screen
• Manually log off
• Change display language
For detailed information about Setup tasks, see “Operator Display Setup Options” on
page 51.
BMTW-SVU02C-EN 3
Selection
buttons
Navigation
buttons
Note:
Occasionally, buttons other than navigation buttons display at
the bottom of a page. Procedural text describes these buttons,
as necessary.
4 BMTW-SVU02C-EN
Button Description
The Top of List button shows items at the top of the current list.
(This button only appears when there are three or more pages.)
The Top of List and Bottom of List buttons appear grayed-out if you are viewing the
top or bottom of the list.
(This button only appears when there are three or more pages.)
The Bottom of List button displays items at the bottom of the current list.
(This button only appears when there are three or more pages.)
The Up button shows the items in the list above the items shown on the screen.
The Up and Down buttons appear grayed-out if you are viewing the top or bottom of
the list.
The Down button shows the items in the list below the items shown on the screen.
The Custom Screen View button provides access to standard view screens (see
Figure 5 on page 7).
BMTW-SVU02C-EN 5
Standard Screens
Standard screens are a part of the Tracer Summit BCU operator display
software. (See Appendix B on page 67 for a list of standard screens avail-
able at the operator display.) Standard screens are identified by a title bar
at the top of each screen (see Figure 4). .
Title bar
Custom Screens
The Trane installer or programmer can create custom screens for use at
the operator display. These screens can be used in place of standard
screens to accomodate specific user requirements at your facility. Custom
screens can be linked to standard view screens by a navigation button
(see Figure 5 on page 7).
Note:
Navigation of custom screens is not discussed in this guide.
6 BMTW-SVU02C-EN
Confirmation Screens
A confirmation screen asks if you wish to proceed with an operation. This
type of screen appears after you make a change to system status (for
example, change a setpoint or edit a schedule). Figure 6 shows an exam-
ple of a confirmation screen for changing a setpoint.
The Trane installer or programmer has the option of disabling non-criti-
cal confirmation screens. Consequently, you may not be prompted to con-
firm some changes.
Note:
Although confirmations screens are not shown in this guide, all
operator-display procedures are written as if all confirmation
screens are enabled.
BMTW-SVU02C-EN 7
Security Screen
The operator-display security screen appears when a password is
required to edit a task (see Figure 7). The password is a four-to-eight-
digit number. Contact your supervisor for more information.
To enter a password:
1. Enter your password by pressing the numerical keys.
2. Press the OK button to display the edit screen. (An edit screen is any
screen that allows you to change or edit system status information.)
Note:
To clear your entry, press the Clear button. To cancel your entry
and return to the previous screen, press the Cancel button.
8 BMTW-SVU02C-EN
You can display and change system status information using the BCU
operator-display view function. The view function enables you to:
• View equipment status
• Change setpoints
• Override equipment controls
Note:
You may not have access to all of the tasks presented in this
guide. Your access privileges depend on your user profile. Con-
tact your supervisor for information.
View Screens
There are two types of view screens associated with the operator-display
view function: custom and standard screens. Standard screens are a part
of the Tracer Summit BCU operator-display software (see Figure 4 on
page 6). Custom screens are created from a screen template and custom-
ized for use at your site (see Figure 5 on page 7).
Note:
Standard screens are available with most, but not all, Tracer
Summit equipment (see Appendix B on page 67).
Custom Screens
If the Trane installer or programmer has selected custom screens for use
at the operator display, then a custom screen is the first screen that dis-
plays after you press the view button on the home screen. Custom screens
can be linked to standard screens by the use of a navigation button (see
Figure 5 on page 7).
Note:
Navigation of custom screens is not discussed in this guide.
Standard Screens
If the Trane installer or programmer has not selected custom screens for
use at the operator display, then standard screens are automatically dis-
played. The first standard screen to display after you press the View but-
ton is the View Equipment screen (see Figure 8 on page 10).
BMTW-SVU02C-EN 9
Note:
The building area sort method only appears if the Trane
installer or programmer has assigned areas to the operator dis-
play.
10 BMTW-SVU02C-EN
BMTW-SVU02C-EN 11
Area Screen #1
Area Screen #2
12 BMTW-SVU02C-EN
Equipment Name
BMTW-SVU02C-EN 13
14 BMTW-SVU02C-EN
Note:
To access the View Equipment screen from a custom screen,
press the Custom Screen View button (see Figure 5 on page 7).
2. Press the Building Area button. The View-By Area list displays, list-
ing in alphabetical order the areas that are available at the BCU
operator display.
Note:
The Building Area button will not display if areas have not
been assigned to the operator display.
Note:
Some equipment may not have a UCM main screen, More
Details screen, or Unit Summary information associated with
it.
The UCM main screen may or may not have a graphic (picture
of the equipment) associated with it.
BMTW-SVU02C-EN 15
Note:
To access the View Equipment screen from a custom screen,
press the Custom Screen View button (see Figure 5 on page 7).
3. Press the name of the equipment you want to view. The UCM main
screen displays for that equipment. You can only view information
from this screen. To change system information, see “Changing Sys-
tem Values” on page 18.
Note:
Some equipment may not have a unit control module (UCM)
main screen, More Details screen, or Unit Summary informa-
tion associated with it.
The UCM main screen may or may not have a graphic (picture
of the equipment) associated with it.
Note:
To access the View Equipment screen from a custom screen,
press the Custom Screen View button (see Figure 5 on page 7).
16 BMTW-SVU02C-EN
Note:
Some equipment may not have a unit control module (UCM)
main screen, More Details screen, or Unit Summary informa-
tion associated with it.
The UCM main screen may or may not have a graphic (picture
of the equipment) associated with it.
Title of screen
Operating conditions
of equipment Press to view more
information about the
equipment
Symbol Description
??? Appears if the UCM or BCU is offline
?Not Initialized Appears if a referencer is used but not initialized
?Not Used? Appears if a referencer is used but disabled
BMTW-SVU02C-EN 17
2. Using one of the sort methods, access the UCM main screen for the
equipment you want to view (see Figure 12 on page 17).
Note:
Some equipment may not have a unit control module UCM
main screen, More Details screen, or Unit Summary informa-
tion associated with it.
The UCM main screen may or may not have a graphic (picture
of the equipment) associated with it.
3. Press the More Details button. The More Details screen displays (see
Figure 13).
18 BMTW-SVU02C-EN
Selection
Property names for the
buttons
equipment being viewed
Note:
If there is no selection button for a setpoint, you cannot change
or edit that setpoint (for example in Figure 14 you cannot edit
the setpoints for Unoccupied Cool Setpoint or Unoccupied Heat
Setpoint: Ref).
BMTW-SVU02C-EN 19
8. Press Yes to confirm your changes and return to the Setpoints screen.
Note:
To clear your entry, press the Clear button. To cancel your entry
and return to the previous screen, press the Cancel button.
2. Using one of the sort methods, access the UCM main screen for the
equipment you want to view.
Note:
Some equipment may not have a UCM main screen, More
Details screen, or Unit Summary information associated with
it.
The UCM main screen may or may not have a graphic (picture
of the equipment) associated with it.
3. Press the More Details button. The More Details screen displays (see
Figure 13 on page 18).
4. Press the Manual Controls button. The Manual Control screen dis-
plays (see Figure 16).
List of available
override properties for
the equipment being
viewed
20 BMTW-SVU02C-EN
Note:
If the present value or lighting value property cannot be over-
ridden at this time, you will need to add the request to the over-
ride control list, see “Making a Manual Request” on page 22.
BMTW-SVU02C-EN 21
◆ Press OK to add your request to the priority list. The operator display
returns you to the Manual Control screen, where the override control
status changes to Manual Request (see Figure 19).
22 BMTW-SVU02C-EN
BMTW-SVU02C-EN 23
2. Using one of the sort methods, access the UCM main screen for the
equipment you want to view.
Note:
Some equipment may not have a unit control module (UCM)
main screen, More Details screen, or Unit Summary informa-
tion associated with it.
The UCM main screen may or may not have a graphic (picture
of the equipment) associated with it.
3. Press the More Details button. The More Details screen displays
(see Figure 13 on page 18).
4. Press the Unit Summary button. The Unit Summary screen displays
(see Figure 21).
24 BMTW-SVU02C-EN
Viewing Diagnostics
The BCU operator display lists active diagnostics for most of the equip-
ment selected for viewing and editing at the display. Active diagnostics
provide information about the state or condition of the equipment that
could adversely affect its operating performance. Figure 22 shows the
presence of an active diagnostic for a piece of equipment.
Indicates an active
diagnostic
BMTW-SVU02C-EN 25
Manual reset
Automatic reset
Informational warning
To view diagnostics:
1. From the home screen, press the View button.
2. Using one of the sort methods, access the UCM main screen for the
equipment you want to view.
Note:
Some equipment may not have a unit control module (UCM)
main screen, More Details screen, or Unit Summary informa-
tion associated with it.
The UCM main screen may or may not have a graphic (picture
of the equipment) associated with it.
3. Press the More Details button. The More Details screen displays (see
Figure 13 on page 18 for an example of the More Details screen).
26 BMTW-SVU02C-EN
The BCU operator display can display all alarms and events received by
the BCU event log. The BCU event log is a list of the 100 most recent
alarms and events sent to the BCU. The event log lists alarms and events
in the order they are received, with the most recent alarms and events
displaying at the top of the event log.
• Alarms notify you when heating, ventilating, and air conditioning
(HVAC) equipment is not operating correctly. For example, an alarm
is generated when communication is down between an HVAC unit
and the BCU or when a filter on an HVAC unit is dirty.
• Events notify you when an action that you need to keep track of
occurs. An example of an event is when communication is restored
with an HVAC unit.
The event log is automatically updated with new alarms and events when
you press the Alarms button on the home screen. The display also auto-
matically updates if you are on the first page of the event log when it
receives new events or alarms.
Note:
You may not have access to all of the tasks presented in this
guide. Your access privileges depend on your user profile. Con-
tact your supervisor for information.
BMTW-SVU02C-EN 27
Alarm Notification
When the operator display receives a new alarm or event, the indicator
light on the display flashes red until all the events in the log have been
viewed. Figure 24 shows the location of the indicator light.
Indicator light
The Trane installer or programmer can set up alarms and events to beep
when they are received by the operator display. The speaker on the BCU
will beep until you press the Alarms button on the home screen. If you
exit the event log with an unacknowledged alarm or event, the system
will reset the beep-timer to beep again in 60 minutes.
Note:
The screen names listed above do not appear on the operator-
display screens. Descriptive screen names have been assigned
to help identify each screen.
28 BMTW-SVU02C-EN
Event Log
Indicates unacknowledged This screen displays all the
alarms or events alarms and events received
by the BCU.
Indicates events or
List of alarms and alarms not viewed
events
Event Details #1
Press to
acknowledge an
alarm or event
Event Details#2
BMTW-SVU02C-EN 29
2. Press a button to view details about the alarm or event. When you
have viewed all of the alarms and events, the operator display indica-
tor light changes from a flashing red light to a steady green light.
Acknowledging an Event
◆ From the events detail screen, press the Acknowledge button to
acknowledge the alarm or event. The screen updates to display who
acknowledged the event and the time it was acknowledged. The label
on the Acknowledge button changes to Delete (see Figure 25 on
page 29).
Deleting an Event
◆ From the events detail screen, press the Delete button to delete the
event or alarm (see Figure 25 on page 29). For unacknowledged
alarms or events, you must first acknowledge the event before you can
delete it.
30 BMTW-SVU02C-EN
The BCU operator display schedule function enables you to view and edit
schedules. Schedules available at the operator display have been selected
for viewing and editing by the Trane installer or programmer.
A schedule is a set of events (instructions) that tells the HVAC (heating,
ventilating, air conditioning) equipment connected to Tracer Summit
what to do and when to do it. For example, an event in a schedule tells a
rooftop unit when to turn on or off.
There are three types of events in a schedule:
• Daily Events: These types of events occur every day, unless you over-
ride them with an exception. (An example daily event is a change in
building occupancy at 6 P.M.) Each day of the week can have separate
events scheduled. Any combination of days can share the same
events. For example, Monday, Wednesday, and Friday can have the
same events, and Tuesday and Thursday could each have a different
set of events or share the same events.
• Holidays: The Trane installer or programmer creates and assigns
these types of events in the Tracer Summit software. (An example of a
holiday would be New Year’s Day or some other designated day.)
You can change the events scheduled for a holiday, but you cannot cre-
ate or delete a holiday from the operator display. The Trane installer
or programmer creates and deletes holidays from a schedule on a
Tracer Summit PC Workstation.
Note:
You cannot create or delete schedules or holidays from the oper-
ator display. These activities are performed in the Tracer Sum-
mit software.
Changes made to schedules from either the operator display or
from a Tracer Summit PC Workstation are automatically
updated the next time the PC Workstation is online with the
site.
BMTW-SVU02C-EN 31
Note:
Most of the screen names listed above do not appear on the
operator-display screens. Descriptive screens names have been
assigned to help identify each screen.
The following sections provide examples for using the schedule screens to
view and edit schedules.
Viewing a Schedule
Figure 26 on page 33 shows an example of how to use the scheduling
screens to view a schedule. The step-by-step procedure for viewing sched-
ules is found on page 35.
In this example, you select the Administration Normal schedule from the
list and then view the events scheduled for September 5, 2001. Scheduled
events display on either the basic events screen or the detailed events
screen. Because there are only two events scheduled and the events are
neither night economize nor analog setpoints, the basic events screen dis-
plays. However, you can still access the detailed events screen by pressing
the Detailed View button.
Editing a Schedule
Figure 27 on page 34 shows an example of how to edit a schedule from the
detailed events screen. This screen is the default events screen when
there is more than two events scheduled or the events are either night
economize or analog setpoints. The step-by-step procedure for editing
schedules start on page 38.
In this example, you change the event start and stop times and then
apply the change to the weekly schedule.
32 BMTW-SVU02C-EN
Schedule List
Calendar
Basic Events
This screen is available when
you have one or two start or
stop events scheduled. These
View the events events can be normal, optimal,
for this schedule or lighting.
BMTW-SVU02C-EN 33
Detailed Events
Event Editor
Enter a new
time
Select Dates
34 BMTW-SVU02C-EN
Viewing Schedules
All operator tasks begin at the home screen (see “Home Screen” on
page 2).
To view a schedule:
4. From the home screen, press the Schedule button. A list of schedules
displays. See Figure 26 on page 33.
5. Press the schedule you want to view. A calendar showing the current
month displays. The current day is highlighted on the calendar.
6. Press a date to view its schedule. The basic events screen or the
detailed events screen displays.
Items
Types of events
scheduled
You can access the Items Scheduled screen by pressing the Items
Scheduled button. This button appears on the calendar, basic events and
detailed events screens (see Figure 26 on page 33 and Figure 27 on
page 34).
BMTW-SVU02C-EN 35
Selection arrows
36 BMTW-SVU02C-EN
Selection arrows
• Day
• Month
• Year
Use the selection arrows to move the cursor over that part of the date
that you want to change.
BMTW-SVU02C-EN 37
3. At the blinking cursor, use the keypad to enter a different month. The
cursor automatically moves to the year field and the keypad changes
to display the numerical keypad (see Figure 30 on page 37).
4. At the blinking cursor, use the keypad and enter a different year.
5. Press OK. The events of that date display for that schedule.
Note:
To reset the calendar back to the current date, press the Reset
button.
2. Press the OK Select Dates button. The select dates screen displays
(see Figure 32 on page 39).
38 BMTW-SVU02C-EN
BMTW-SVU02C-EN 39
2. Use the keypad to enter the new time or duration. Use the AM or PM
buttons to indicate the time of day.
Note:
If you need to clear your entry, press the Clear button. Press the
Cancel button to return to the previous screen without making
any changes.
4. Press the OK Select Dates button. The select dates screen displays
(see Figure 32 on page 39).
• From the basic events screen, press the Detailed View button.
The detailed events screen displays (see Figure 27 on page 34).
• If you are already at the detailed events screen, go to step 2.
2. Press the Add or Remove button. The Add or Remove screen displays
(see Figure 34).
Remove exception
button
Add button
Remove button
40 BMTW-SVU02C-EN
3. Select the Add button to add an event to the schedule. A list of avail-
able events displays (see Figure 35).
4. Select the event you want to add to the schedule. The events editor
displays (see Figure 27 on page 34).
7. Press the OK Select Dates button. The select dates screens displays
(see Figure 27 on page 34).
• From the basic events screen, press the Detailed View button.
The detailed events screen displays (see Figure 27 on page 34).
• If you are already at the detailed events screen, go to step 2.
2. Press the Add or Remove button. The Add or Remove screen displays
(see Figure 34 on page 40).
3. Press the Remove button to remove an event from the schedule. A list
of available events displays (see Figure 36 on page 42).
BMTW-SVU02C-EN 41
4. Select the event you want to remove from the schedule. The operator
display returns you to the basic or detailed events screen.
5. Press the OK Select Dates button. The select dates screen displays
(see Figure 27 on page 34).
Creating Exceptions
You can create an exception that applies a one-time change to a schedule
or applies the change to specific dates. The schedule reverts back to the
normal schedule after the last day of the exception.
The type of schedule in effect is displayed in the top right corner of the
basic events or detailed events screen (see Figure 37 on page 43). The
schedule in effect is either regular, exception or holiday.
42 BMTW-SVU02C-EN
Type of schedule in
effect
2. Press the OK Select Dates button. The select dates screen displays
(see Figure 32 on page 39).
3. To create a one-time exception for the current day, select the button
that displays the current date. A confirmation screens displays.
4. Press Yes to apply the exception to the schedule for the current date.
The operator display returns you to the basic or detailed events
screen.
2. Press the OK Select Dates button. The select dates screens displays
(see Figure 32 on page 39).
3. Press the Specific Dates Only button. The calendar screen displays.
4. Select the start date. A diamond symbol appears on the selected date,
indicating the start date of the exception. Figure 38 on page 44 shows
a calendar indicating an exception to the schedule from September 7
through September 10.
BMTW-SVU02C-EN 43
Indicates an
exception
6. Press Yes to apply the exception to the schedule for the specified
dates. The operator display returns you to the basic or detailed events
screen.
• From the basic events screen, press the Detailed View button.
The detailed events screen displays.
• If you are already at the detailed events screen, go to step 2.
2. Press the Add or Remove button. The Add or Remove screen displays
(see Figure 34 on page 40).
4. Press Yes to delete the exception. The operator display returns you to
the detailed events screen.
44 BMTW-SVU02C-EN
2. Press the OK Select Dates button. The select dates screens displays
(see Figure 32 on page 39).
3. Press the Select Days of the Week button. A screen showing the days
of the week displays (see Figure 39).
Note:
Press the Clear button to remove all of the check marks.
BMTW-SVU02C-EN 45
Indicates a holiday
schedule
2. From the basic or detailed event screen, change the events to repre-
sent the events for the holiday.
3. Press the OK Select Dates button to display the select dates screen
(see Figure 32 on page 39).
5. Press the holiday that you want to apply the changes to.
46 BMTW-SVU02C-EN
Chapter 5
You can start or cancel a timed override (TOV) request for an area from
the BCU operator display. A TOV button appears on the home screen
when this function is available (see “Home Screen” on page 2). TOV is set
up and enabled from a Tracer Summit PC Workstation by a Trane pro-
grammer or installer.
Note:
You may not have access to all of the tasks presented in this
guide. Your access privileges depend on your user profile. Con-
tact your supervisor for information.
Note:
Descriptive screen names have been assigned to help identify
each screen in Figure 41 on page 48.
BMTW-SVU02C-EN 47
Press to change
duration
Press to start a
TOV request
48 BMTW-SVU02C-EN
2. Press the up and down arrow buttons to change the duration of the
timed override request. The duration is changed in increments or dec-
rements of 15 minutes.
Note:
The Trane installer or programmer determines the maximum
possible duration when setting up TOV in Tracer Summit.
3. Press the Start Timed Override button to start your timed override
request. The timed override remains active for the number of minutes
shown.
2. Press the area you want to restart a timed override request for. The
Time Override Status dialog box displays.
2. Press the area you want to cancel a timed override request for. The
Time Override Status dialog box displays.
BMTW-SVU02C-EN 49
50 BMTW-SVU02C-EN
The BCU operator display setup function enables you to change BCU and
operator display system settings (see Figure 42). The setup function
enables you to:
• Set time and date
• Set the time format
• Adjust brightness
• Calibrate the operator display touch screen
• Log off from the operator display
• Change display language
Note:
You may not have access to all of the tasks presented in this
guide. Your access privileges depend on your user profile. Con-
tact your supervisor for information.
BMTW-SVU02C-EN 51
2. Press the Set Time button. The Set System Time screen displays (see
Figure 43).
3. Enter the new time by pressing the numbers on the keypad. If you
need to clear your entry, press the Clear button,
Note:
The default selection for the time of day is AM. You need to
press the PM button to change the time to a PM setting.
5. Press Yes to confirm your changes and return to the Setup menu. The
new time is displayed on the Set Time button.
52 BMTW-SVU02C-EN
2. Press the Set Date button. The Set System Date screen displays (see
Figure 44).
Selection arrows
• Day
• Month
• Year
Use the selection arrows to move the cursor over that part of the date
that you want to change.
BMTW-SVU02C-EN 53
4. At the blinking cursor, use the keypad to enter a different month. The
cursor automatically moves to the year field and the keypad changes
to display the numerical keypad (see Figure 44 on page 53).
5. At the blinking cursor, use the keypad and enter a different year.
6. Press OK. The events of that date display for that schedule.
Note:
To reset the calendar back to the current date, press the Reset
button.
54 BMTW-SVU02C-EN
Adjusting Brightness
The following procedure enables you to adjust the brightness of the
operator-display touch screen.
1. From the home screen, press the Setup button. The Setup menu dis-
plays (see Figure 42 on page 51).
Maximum
brightness
Maximum darkness
3. Press the top row of buttons from left to right to increase the bright-
ness of the touch screen. Press the buttons from right to left to
decrease the brightness of the touch screen.
BMTW-SVU02C-EN 55
2. Press the Calibrate Touch Screen button. The calibration screen dis-
plays with the calibration target in the upper left-hand corner of the
screen (see Figure 48).
Calibration target
CAUTION
AVOID EQUIPMENT DAMAGE!
Do not use sharp objects on the touch screen.
3. Touch the target using your finger or a small, pliable, blunt object,
such as a pencil eraser. Hold until the beeping stops. The calibration
target appears at the bottom right-hand corner of the screen (see
Figure 49 on page 57).
56 BMTW-SVU02C-EN
Calibration target
4. Again, touch the target with the object. Hold until the beeping stops.
The touch screen is now calibrated and the operator display returns
you to the Setup menu.
BMTW-SVU02C-EN 57
Note:
The display language option is only available on BMTXs with
images of version 17 or higher.
2. Press the Log Off button. The operator display logs you off.
Note:
You will need to re-enter your password if the operator display
has security assigned for a particular task.
58 BMTW-SVU02C-EN
Operator-display touch
screen
CAUTION
AVOID EQUIPMENT DAMAGE!
Take care not to let any liquid run down into the BCU. Any liquid coming
in contact with the BCU circuit board could cause the touch screen or
the BCU to malfunction.
BMTW-SVU02C-EN 59
60 BMTW-SVU02C-EN
A Alarms
A notification that HVAC equipment is not operating correctly. For exam-
ple, an alarm is generated when communication is down between an
HVAC unit and the BCU, or when a filter on an HVAC unit is dirty.
B BMTW BCU
See Building control unit
Buttons
See Targets
C Custom Screen
A screen that is created by an advanced user. A custom screen contains a
Home button and a Back button. It may also include a monochrome bit-
map, up to 10 data items, and custom navigation buttons.
D Diagnostic
A program that checks the operation of a device board or other component
for malfunctions and errors and reports its findings.
E Event log
The event log contains a record of events and alarms. An event log has the
following information:
• A short description of the alarm or event
• Whether you must acknowledge the alarm
BMTW-SVU02C-EN 61
• Whether the alarm or event was generated by the operator (for exam-
ple, an operator logs on) or by Tracer Summit PC Workstation soft-
ware (for example, a pump shuts down)
• Name of the PC workstation at which operator-generated events
occur
• The site at which the alarm or event occurred
Event
A notification of an action that you need to keep track of. For example,
when a new operator logs on to Tracer Summit.
Event types
Types of events found in a schedule, include the following:
• Normal
• Optimize
• Night Economize
• Lighting
• Setpoints
Exception days
Days during which exceptions to (differences from) normally scheduled
events occur.
H Holidays
Recurring days where the facility is not operating under the usual sched-
ule.
HVAC
Heating, ventilating, and air conditioning.
L Lighting
An option that turns lights on or off at specified start times.
N Night economize
Turns on HVAC equipment at a specified start time at night and opens
the outdoor air damper/economizer to let in cool outdoor air. Closes
damper and turns off equipment at a specified end time.
Normal
A setting that turns on HVAC equipment for operation in a normal, occu-
pied mode at a specified start time and turns off equipment at a specified
end time.
62 BMTW-SVU02C-EN
O Occupied
A term used to define the state of an application or UCM. Typically, it
means that equipment and software will control to certain parameters
based on the knowledge that the system is providing comfort control to a
space in which people reside.
Operator Display
The operator display is a touch screen interface located on the BCU front
panel. It enables you to perform daily operator tasks, as well as view
information about your building automation system (BAS) without
requiring a Tracer Summit PC Workstation.
Optimal
A setting that optimizes the startup and shutdown times of heating and
cooling equipment. Under this setting, equipment will run only as long as
necessary to meet the required temperature setpoints at the time of occu-
pancy.
Override
A method of controlling system settings, either manually or through the
system, that changes the current or normal system function at the time
the control occurs.
Property
One element of an object’s characteristic information. This information
element can be viewed, referenced, and applied throughout the Tracer
Summit system.
S Schedule
A set of events (instructions) that tell the HVAC equipment connected to
Tracer Summit what to do and when to do it. For example, an event in a
schedule will tell a rooftop unit when to turn on and off.
Setpoints
An option that changes the heating or cooling mode at a specified time or
using a specified number or other setting. When the equipment goes
beyond (above or below) that setting, it is automatically switched to
another mode.
BMTW-SVU02C-EN 63
Standard Screen
The menu-driven screens that enable the user to navigate within the
BCU operator display. Depending on the context, a standard screen will
have any combination of static text, live text, or icons.
T Targets
Buttons or text used as targets to link to other items on a screen.
Touch screen
A transparent overlay on an LCD or cathode ray tube (CRT) that is sensi-
tive to touch by a finger or stylus.
Tracer Summit
Trane’s premier building management system that allows facility manag-
ers to operate a building in an optimized and efficient manner. Tracer
Summit gives the facility operator control of temperature, humidity,
scheduling, lighting, energy, and much more. All of these building control
capabilities can be programmed and managed as a single system through
Tracer Summit.
64 BMTW-SVU02C-EN
Declaration of Conformity
This appendix provides the Declaration of Conformity statement for the BCU
operator display.
BMTW-SVU02C-EN 65
IEC 1000-4-6:1996 10 V
EN61000-4-6 0.15 .. 80 MHz
Craig Kasl
Design/Compliance Engineer
66 BMTW-SVU02C-EN
Appendix B
Standard Screens
Note:
The Trane installer or programmer selects the equipment that
is displayed at the operator display. If a particular piece of
equipment has not been selected, the associated standard
screen is not available at the operator display.
Note:
Standard screens are not available for the Central Control
Panel (CCP) and non-Trane BACnet objects.
BMTW-SVU02C-EN 67
68 BMTW-SVU02C-EN
A E
Alarm conditions, 28 Event
Alarms and events Adding to a schedule, 40
Acknowledging, 30 Definition, 31
Definitions, 27 Deleting from schedule, 41
Deleting, 30 Event log
Screens associated with, 28 Definition, 30, 61
Alarms button Viewing, 30
Description of, 3 Event type
Definition, 62
Exception in a schedule
B Definition, 31
Back button Exceptions
Description of, 5 Creating, 42
BCU operator display, 1 Removing, 44
Logging off, 58
Setup options for, 51
H
BMTW BCU, 1
Bottom of List button Holiday
Description of, 5 Changing events for, 46
Definition, 31
Building automation system
Definition, 61 Home button
Description of, 5
Building control unit
Definition, 61 HVAC equipment
Definition of HVAC, 62
Scheduling for, 31
C
Calendar N
Selecting month and day, 36
Navigation buttons
Confirmation screens, 7
Description of, 5
Custom screens, 6
Night economize
Definition, 61
Definition, 62
View button, description of, 5
Normal
Definition, 62
D
Declaration of Conformity, 65 O
Diagnostics, 25
Occupied, 63
Down button
Operator display
Description of, 5
See BCU operator display
Optimal
BMTW-SVU02C-EN 69
Definition, 63 T
Override control status
description, 21 Task buttons
Description of, 3
Overrides
Making a manual request, 22 Time and Date, setting up, 52
System values, 20 Timed override
Canceling a request, 49
Definition of, 64
P Restarting a request, 49
Starting a request, 49
Passwords Using the TOV screens, 47
Editing task lists with, 8
Timed override button
PC workstation Description of, 3
Definition, 63
Top of the List button
Present value Description of, 5
Override screen, example of, 21
Touch screen, 2
Releasing control of, 23
Adjusting brightness, 55
Property Calibration, 56
Definition, 63 Maintenance, 59
Override control status, 21 Setup options for, 51
Tracer Summit, 1
Definition of, 64
S
Schedule button
Description of, 3 U
Schedules UCM main screen
Example of editing, 32 Viewing operating setpoints, 17
Example of viewing, 32
Unit summary information, 24
Making permanent changes to,
45 Up button
Screens associated with, 32 Description of, 5
Viewing scheduled items, 35
Scheduling
Definition, 31
V
Security screen, 8 View button
Selection buttons Description of, 3
Description of, 2 View Screens
Setpoint Viewing by building area, 10
Changing unit setpoints, 18 Viewing by equipment type, 10
Definition, 63 Viewing by name of equipment,
displaying question marks, 17 10
Setup button
Description of, 3
Standard screens, 6, 67
System Status Information
Viewing and changing, 9
System values
Changing unit setpoints, 18
70 BMTW-SVU02C-EN
For more information contact Trane has a policy of continuous product and product data improvement and reserves the right to
your local district office or change design and specifications without notice. Only qualified technicians should perform the installa-
e-mail us at [email protected] tion and servicing of equipment referred to in this publication.