DI−76

DIAGNOSTICS − ENGINE
DI322−02

ECU Power Source Circuit

CIRCUIT DESCRIPTION
When the ignition switch is turned ON, battery positive voltage is applied to the coil, closing the contacts of
the ECD main relay (Marking: ECD) and supplying power to the terminal +B of the engine ECU.

WIRING DIAGRAM

Engine ECU
Cowl Side J/B LH B−R (LHD)
12 IGN 21 14
1 2D B−R B−R IGSW
2B E19
(RHD) B B (RHD)
J/26 J/C
B−R
Ignition Switch
2
6 7 W−R W−R
IG1

W−R

Engine Room J/B J18 J/C (LHD)

AM2 ECD ECD Relay J11 J/C (RHD)
10 7 2 12
1E 1C
B−Y
IG2 B−Y B−Y E19 +B
2 4
1 13 8 3 MREL
3 1 B−W B−W
1N 1C IG2 E19

14
BR E1
E17
A
B
J7 J/C

Fusible Link Block A

Battery
6 MAIN ALT EE

ED (LHD)
EC (RHD)

B05265

1HZ, 1HD−T, 1HD−FTE ENGINE (RM617E)

 DI−77
DIAGNOSTICS − ENGINE

INSPECTION PROCEDURE

1 Check voltage between terminals +B and E1 of engine ECU.

ON PREPARATION:
E1 +B (a) Remove the glove compartment door.
(b) Turn the ignition switch ON.
CHECK:
Measure voltage between terminals +B and E1 of engine ECU.
OK:
Voltage: 9 − 14 V
(−) (+)
A04962

OK Proceed to next circuit inspection shown on

problem symptoms table (See page DI−19).

NG

2 Check for open in harness and connector between terminal E1 of engine ECU
and body ground (See page IN−19).

NG Repair or replace harness or connector.

OK

3 Check ECD main relay (Marking: ECD) (See page ED−3).

NG Replace ECD main relay.

OK

1HZ, 1HD−T, 1HD−FTE ENGINE (RM617E)

DI−78
DIAGNOSTICS − ENGINE

4 Check ECD fuse.

PREPARATION:
Remove the ECD fuse from the engine room J/B.
CHECK:
Check continuity of ECD fuse.
OK:
Continuity

NG Check for short in all the harness and

components connected to ECD fuse.

OK

5 Check for open in harness and connector between engine ECU and ECD main
relay (Marking: ECD), ECD main relay and battery (See page IN−19).

NG Repair harness or connector.

OK

6 Check voltage between terminals IGSW and E1 of engine ECU.

ON PREPARATION:
E1 IGSW (a) Remove the glove compartment door.
(b) Turn the ignition switch ON.
CHECK:
Measure voltage between terminals IGSW and E1 of engine
ECU.
OK:
(−) (+) Voltage : 9 − 14 V
A04963

OK Go to step 9.

NG

1HZ, 1HD−T, 1HD−FTE ENGINE (RM617E)

 DI−79
DIAGNOSTICS − ENGINE

7 Check ignition switch (See Pub. No. RM616E2 BE section).

NG Replace ignition switch.

OK

8 Check for open in harness and connector between ignition switch and engine
ECU (See page IN−19).

NG Repair or replace harness or connector.

OK

9 Check voltage between terminal MREL of engine ECU and body ground.

ON PREPARATION:
MREL
(a) Remove the glove compartment door.
(b) Turn the ignition switch ON.
CHECK:
Measure voltage between terminal MREL of engine ECU and
body ground.
OK:
(−) (+)
Voltage: 9 − 14 V
A04964

OK Check and replace engine ECU

(See page IN−19).

NG

Check for open in harness and connector between engine ECU and ECD main relay (Marking:
ECD), ECD main relay and body ground (See page IN−19).

1HZ, 1HD−T, 1HD−FTE ENGINE (RM617E)