4022510 JFG _ v Sem TD Notes of Lesson

Introduction to
JIGS AND FIXTURES

Introduction
The successful running of any mass production depends
upon the interchangeability to facilitate easy assembly
and reduction of unit cost. Mass production methods
demand a fast and easy method of positioning work for
accurate operations on it.
Jigs and fixtures are production tools used to
accurately manufacture duplicate and interchangeable
parts. Jigs and fixtures are specially designed so that large
numbers of components can be machined or assembled
identically, and to ensure interchangeability of
components.
JIGS
It is a work holding device that holds, supports and locates the workpiece
and guides the cutting tool for a specific operation. Jigs are usually fitted
with hardened steel bushings for guiding or other cutting tools. a jig is a
type of tool used to control the location and/or motion of another tool. A
jig's primary purpose is to provide repeatability, accuracy, and
interchangeability in the manufacturing of products. A device that does
both functions (holding the work and guiding a tool) is called a jig.
An example of a jig is when a key is duplicated, the original is used as a jig

so the new key can have the same path as the old one.
BORING JIG
FIXTURES
It is a work holding device that holds, supports and locates the workpiece
for a specific operation but does not guide the cutting tool. It provides
only a reference surface or a device. What makes a fixture unique is that
each one is built to fit a particular part or shape. The main purpose of a
fixture is to locate and in some cases hold a workpiece during either a
machining operation or some other industrial process. A jig differs from a
fixture in that a it guides the tool to its correct position in addition to
locating and supporting the workpiece.
Examples: Vises, chucks
A VISE-JAW FIXTURE
How do jigs and fixtures differ
JIGS FIXTURES
1. It is a work holding device that holds, 1. It is a work holding device that holds,
supports and locates the workpiece and supports and locates the workpiece for a
guides the cutting tool for a specific specific operation but does not guide the
operation cutting tool
2. Jigs are not clamped to the drill press 2. Fixtures should be securely clamped to
table unless large diameters to be drilled the table of the machine upon which the
and there is a necessity to move the jig to work is done.
bring one each bush directly under the drill.
JIGS FIXTURES
3. The jigs are special tools particularly in 3. Fixtures are specific tools used
drilling, reaming, tapping and boring particularly in milling machine, shapers and
operation. slotting machine.
4. Gauge blocks are not necessary. 4. Gauge blocks may be provided for
effective handling.
5. Lighter in construction. 5. Heavier in construction.
Advantages of Jigs and Fixtures
PRODUCTIVITY:
Jigs and fixtures increases the productivity by eliminating the
individual marking, positioning and frequent checking. The
operation time is also reduced due to increase in speed, feed
and depth of cut because of high clamping rigidity.
INTERCHANGEABILITY AND QUALITY:

Jigs and fixtures facilitate the production of articles in large
quantities with high degree of accuracy, uniform quality and
interchangeability at a competitive cost .
 SKILL REDUCTION:
There is no need for skillful setting of work on tool. Jigs and
fixtures makes possible to employ unskilled or semi skilled
machine operator to make savings in labour cost.
 COST REDUCTION:
Higher production, reduction in scrap, easy assembly and
savings in labour cost results in ultimate reduction in unit
cost.
Fundamental principles of Jigs
and Fixtures design
LOCATING POINTS: Good facilities should be provided for
locating the work. The article to be machined must be easily
inserted and quickly taken out from the jig so that no time is
wasted in placing the workpiece in position to perform
operations. The position of workpiece should be accurate with
respect to tool guiding in the jig or setting elements in fixture.
FOOL PROOF: The design of jigs and fixtures should be such

that it would not permit the workpiece or the tool to inserted in
any position other than the correct one.
• REDUCTION OF IDLE TIME: Design of Jigs and Fixtures should be
such that the process, loading, clamping and unloading time of the
workpiece takes minimum as far as possible.
• WEIGHT OF JIGS AND FIXTURES: It should be easy to handle,

smaller in size and low cost in regard to amount of material used
without sacrificing rigidity and stiffness.
• JIGS PROVIDED WITH FEET: Jigs sometimes are provided with feet
so that it can be placed on the table of the machine.
• MATERIALS FOR JIGS AND FIXTURES: Usually made of hardened

materials to avoid frequent damage and to resist wear. Example-
MS, Cast iron, Diesteel, CS, HSS.
• CLAMPING DEVICE:
It should be as simple as possible without sacrificing
effectiveness. The strength of clamp should be such that not
only to hold the workpiece firmly in place but also to take the
strain of the cutting tool without springing when designing
the jigs and fixtures.
Essential features of Jigs and Fixtures
 Reduction of idle time – Should enable easy clamping and
unloading such that idle time is minimum
 Cleanliness of machining process – Design must be such that not

much time is wasted in cleaning of scarfs, burrs, chips etc.
 Replaceable part or standardization – The locating and supporting

surfaces as far as possible should be replaceable, should be
standardized so that their interchangeable manufacture is possible
 Provision for coolant – Provision should be there so that the tool is

cooled and the swarfs and chips are washed away
 Hardened surfaces – All locating and supporting surfaces
should be hardened materials as far as conditions permit so
that they are not quickly worn out and accuracy is retained
for a long time
 Inserts and pads – Should always be riveted to those faces of

the clamps which will come in contact with finished surfaces
of the workpiece so that they are not spoilt
 Fool-proofing – Pins and other devices of simple nature

incorporated in such a position that they will always spoil the
placement of the component or hinder the fitting of the
cutting tool until the latter are in correct pos
 Economic soundness – Equipment should be economically
sound, cost of design and manufacture should be in
proportion to the quantity and price of producer
 Easy manipulation – It should be as light in weight as possible

and easy to handle so that workman is not subjected to
fatigue, should be provided with adequate lift aids
 Initial location – Should be ensured that workpiece is not

located on more than 3 points in anyone plane test to avoid
rocking, spring loading should be done
 Position of clamps – Clamping should occur directly above

the points supporting the workpiece to avoid distortion and
springing
 Clearance – Sufficient amount of clearance should be provided
around the work so that operator’s hands can easily enter the
body for placing the workpiece and any variations of work can be
accommodated
 Ejecting devices – Proper ejecting devices should be incorporated

in the body to push the workpiece out after operation
 Rigidity and stability – It should remain perfectly rigid and stable

during operation. Provision should be made for proper positioning
and rigidly holding the jigs and fixtures
 Safety – The design should assure perfect safety of the operator

General rules for designing
Compare the cost of production of work with present
tools with the expected cost of production, using the
tool to be made and see that the cost of buildings is not
in excess of expected gain.
Decide upon locating points and outline clamping
arrangement
Make all clamping and binding devices as quick acting as
possible
Make the jig fool proof
Make some locating points adjustable
Avoid complicated clamping arrangements
Round all corners
Provide handles wherever these will make handling easy
Provide abundant clearance
Provide holes on escapes for chips
Locate clamps so that they will be in best position to
resist the pressure of the cutting tool when at work
Place all clamps as nearly as possible opposite some
bearing point of the work to avoid springing action
Before using in the shop, test all jigs as soon as made
MATERIALS USED
 Jigs and Fixtures are made of variety of materials, some of
which can be hardened to resist wear.
 Materials generally used:
 High speed Steel: Cutting tools like drills, reamers and milling
cutters.
 Die steels: Used for press tools, contain 1% carbon, 0.5 to 1%
tungsten and less quantities of silicon and manganese.
 Carbon steels: Used for standard cutting tools.
 Collet steels: Spring steels containing 1% carbon, 0.5%
manganese and less of silicon.
5. Non shrinking tool steels:
High carbon or high chromium
Very little distortion during heat treatment.
Used widely for fine, intricate press tools.
6. Nickel chrome steels: Used for gears.
7. High tensile steels: Used for fasteners like high tensile
screws
8. Mild steel:
Used in most part of Jigs and Fixtures
Cheapest material
Contains less than 0.3% carbon
9. Cast Iron:
Used for odd shapes to some machining and
laborious fabrication
CI usage requires a pattern for casting
Contains more than 2% carbon
Has self lubricating properties
Can withstand vibrations and suitable for base
10. Nylon and Fiber: Used for soft lining for clamps to
damage to workpiece due to clamping pressure
11. Phospher bronze:
used for nuts as have high tensile strength
Used for nuts of the lead screw
Factors to be considered for design of
Jigs and Fixtures
1. Component-
Design to be studied carefully
Ensure work is performed in a proper sequence
Maximum operations should be performed on a machine in
single setting
2. Capacity of the machine-
Careful consideration to be performed on type and capacity
of machine.
3. Production requirements-
Design to be made on basis of actual production
requirements. Then comes decision on manual and automatic
tooling arrangements.
4. Location-
• Location should ensure equal distribution of forces
throughout all sequence of operation.
• Location should be hard resistant, wear resistant and
high degree of accuracy.
• Movement of workpiece should be restricted.
• Should be fool proofed to avoid improper locations of
the workpiece.
• Should facilitate easy and quick loading of workpiece.
• Redundant locators should be avoided.
• Sharp corners must be avoided.
• At least one datum surface should be establised.
5. Loading and Unloading arrangements-
There should be adequate clearance for loading and
unloading. Hence process becomes quick and easy.
Size variation must be accepted.
It should be hardened material and non sticky.
6. Clamping arrangements-
Quick acting clamps must be used as far as possible.
The clamping should not cause any deformation to the
workpiece
It should always be arranged directly above points supporting
the work.
Power driven clamps are favoured as they are quick acting,
controllable, reliable and operated without causing any
fatigue to the operators.
Features of clamps:
Clamping pressure should be low
Should not cause distortion
Simple and fool proof
Movement of clamp should be minimum
Case hardened to prevent wear
Sufficiently robust to avoid bending
7. Clearance between Jig and Component-
To accommodate various sizes if work
Chips to pass out of the opening between them
8. Ejectors-
To remove work from close fitting locators.
Speeds up unloading of the part from the tool and hence
production rate.
9. Base and Body construction-
Methods used: Machining, Forging and machining, Casting,
Fabricating, Welding.
10. Tool guiding and cutter setting-
By adjusting the machine or using cutter setting block, the
cutter is set relative to the work in a fixture. The drill bushes
fitted on jig plates guides the tools.
11. Rigidity and vibration-
Must possess enough rigidity and robustness.
Should not vibrate as it may lead to unwanted movement of
workpiece and tools.
12. Safety-
Operation should be assured full safety.
13. Cost-
Should be simple as possible.
Cost incurred should be optimum.
14. Materials generally used-
Sl. No Part Name Material
1 Jig body CI
2 Stud MS
3 Drill/Bush Gun metal
4 Pin MS
5 Nut MS
Locating Principles
&
Devices
1
LOCATING PRINCIPLES
To position the work piece w.r.t. to tool, to ensure
precision in machining
Locating: dimensional and positional relation-

ship b/w work piece and tool
Locator: device to establish and maintain position of

a part in a jig or fixture
2
BASIC PRINCIPLES
Positioning the locator
Accuracy & tolerances
Fool proofing
Duplicate location
Motion economy
3
1- Positioning the locators
Locators should contact the work (preferably machines surface) on a
solid and stable point:
This permits accurate placement of the part in the tool &
ensures the repeatability of the jig and fixture
 They should be placed as far as possible:

 This permits the use of fewer locators
 Ensures complete contact over the locating surface
2- Accuracy and Tolerance
The workpiece itself determines the overall
size of a locating element.
locators must be made to suit the MMC

(Maximum-Material Condition) of the area
to be located. (The MMC of a feature is the size of
the feature where is has the maximum amount of
material).
With external features, like shafts, the MMC is

the largest size within the limits.
With internal features, like holes, it is the

smallest size within the limits.
5
6
FOOL PROOFING
Ensures that the part fits into the tool in its correct
position only
The simplest and most cost effective method is
positioning a
fool proof pin.
7
8
4- Duplicate locators
Redundant, or duplicate, locators should be avoided. b) Both the hub

and the flange
a) Flat surface locating the same
can be parallal surface
redundantly
located. The
part should
be located on
only one, not
both, side of
surfaces.
c) Difficulty with combining
hole and surface location:
Either locational method
(locating from the holes or
locating from the edges)
works well if used alone.
9
5. Motion Economy
It involves use of easy, quick and economic loading of
work pieces.
10
Degrees of Freedom

Here we consider 12
degrees of freedom(not 6).

4 along each axis;2
translational and two
rotational.
11
Restriction of Movement:
Six-pin method(3-2-1 method):

Motion is restricted using clamps and locators.
A three pin base can restrict five motions.
>Rotation about X,Y axes.(4 motions)
>Translation along -ve z-axis
(1 motion)
Directions nine, ten and eleven are restricted
by a clamping device.
(3 motions)
12
Cont..
To restrict the movement of the part

around the ZZ-
axis and in direction eight, two more pin-
type locators are positioned in a vertical
plane.(3 motions)
A single pin locator in vertical plane

restricts motion along direction 7.( 1
motion)
So motion in all 12 directions are
restricted.
13
Locating Principles and
Devices
Six-pins- restrict nine motions.
Other three are restricted by using a clamp.
14
>>contd.
This is the most common locating method employed for

square or rectangular parts.
Flat bases may also be used, but these should be installed

rather than machining into the base.
But pin/button type locators offers more accuracy as the area

of contact is less. Moreover, they raise the work above the base
so that chips wont interrupt the operation.
15
Workpieces with holes:
 Holes provide an excellent method for locating.
 A round pin inside the hole(primary) and a diamond
pin(secondary) can restrict 11 motions!
16
17
Locating Methods:
Locating from a Flat Surface:
There are three primary methods of locating work from a flat
surface:

solid supports

adjustable supports,

equalizing supports
18
Solid supports:

Easiest and cheapest.

Less accurate.

Used where machined surface acts as a
locating point.
19
Adjustable supports:

Used where surfaces are uneven(casting,forging..)

Threaded style is the easiest and more economical.

Adjustable locators are normally used with one or more
solid locators to allow any adjustment needed to level the
work.
20
Equalizing supports:

They provide equal support through two connected contact
points.

As one point is depressed, the other raises and maintains
contact with the part.

This feature is especially necessary on uneven cast surfaces.
21
Locating from an Internal Diameter

Locating a part from a hole or pattern is the most effective
way to accurately position work.

Nine of the twelve directions of movement are restricted by
using a single pin, and eleven directions of movement are
restricted with two pins.

When possible, it is logical to use holes as primary part
locators.
22
Locating Principles and
Devices
23
Locating Cylindrical Surfaces(Externally)
“V”-locators

Vee locators are used mainly for round work.

They can locate flat work with rounded or angular ends and flat
discs.

Two types:Fixed and Adjustable:
24
Locating from Irregular Surfaces(External)
Locating work from an external

profile, or outside edge, is the most
common method of locating work
in the early stages of machining.

For simple components,a
sighting plate may be used.
Location is done by adjusting
the workpiece in such a way that
it has equal margins on all
sides.

In large parts cylindrical pins
can be used.
25
cont..(irregular surfaces)

If there are large variations from batch to batch,
eccentric locators can be used, whose
eccentricity can be varied according to the
profile.

Eccentricity is varied just by rotating the locator
until it holds the workpiece in position.
26
(cont; irregular profiles)
Locating from an External Profile

Nesting locators position a part by
enclosing it in a depression, or
recess, of the same shape as the
part.

Nesting is the most accurate locating
device for profile location.

Obviously, the height of the nest
should be lesser than the height of
the workpiece.

In case of sheet-metals or thin
workpieces, finger slots or ejector
pins should be provided.
27
Pin and button locator
 locator used to support or hold the
workpiece in position.
 Pins locators are longer and for
horizontal locations. Button locators
shorter,vertical locations.
 Locating buttons-press fit and
screwed(wear and tear more –
replaceable)
Rest pads and plates
 Used with heavier and larger
workpiece.
 To support and locate the work
vertically.
 Hold jig or fixture base plate by
socket-head cap screws.
Diamond pin locator
 Work piece with the drilled holes use

two round pins
 If dimension variation between centre
to centre distance of the holes, one
round and diamond pin locators are
used
 Binding is eliminated
 Prevents movement around the pin
and are relieved on two sides to allow
variation
Nesting locator or cavity locator
 used to position the work piece
 Accurate method for profile location
 No need of supplementary locating
devices
 But it is difficult to lift out of cavity
 Common types:-
Ring Nest
 Used for cylindrical workpiece.

 It encloses the workpieces fully.
1.Full Nest
 For work pieces other than cylinders.

 Encloses the work completely.
Partial Nest
 For larger work pieces a nest may not be possible

to enclose it completely.
 In such cases partial nests are used which
encloses certain contours of the work.
Spherical locator
Sphercal location reduces contact

area.
Material not in direct contact with the
work piece.
Binding not possible in this case
Split contact locator
 Relieved locator used in thick workpiece

 Locator is relieved in the middle
 Only top and bottom areas come in contact
with workpiece
Raised contact locator
 Raised contact design reducing the chance
of binding
 Contact point is raised to the middle of the
workpiece and contact area reduced
 Moving the contact area from the base plate
reduces the effect of dirt,chip and burrs
Split pin or groove pin
 Used in place of dowel pins to reduce cost
and time
 Not so accurate as they don’t employ the
reamed hole as in the case of dowel pins
Dowel pin locator
 Most common type of fixed locator
Cylindrical pin
 Used when the workpiece contains
holes drilled into it
 Pin will bind unless centreline of the
hole is perfectly aligned with cetreline
of locator
Machined Fixed stop locator
 Used for parts that cannot be used in either
a nest or V-locator
 Are usually machined into the tool body
 Since they are machined into the tool body
the entire body has to be changed when
locator is worn out
Installed fixed stop locator
 Most economical to use
 Since it is installed into the tool body and not
machined it can be easily replaced when
worn out
 No need to make the locator body entirely
again
 Saves time
Standard parts
jig button
 Commonly made from case hardening steel
(16MnCr5 or 20MnCr5C15)
 Have a hardness value of about 60 HRC
 Have a case depth of 0.3 to 0.5 mm
Jig bush
 Jig bushes locate and guide cutting tools
 Several types like linear,renewable,slip and screw
bushes exist
 Made from direct hardening type steel such as
En31,T90,20MnV8
 Hardness is usually 60 HRC with case hardened depth
of 0.5 to 0.8mm
Ejectors
 Used to remove the workpiece from close fitted
locators and are present behind the workpiece
 Speed up the operation by reducing unloading time
 They are of 2 types:
• Mechanical type
• Spring plunger
Jig feet bolt and nuts
 Usually purchased as standard parts and
they are built into jig body except in casting
construction
 Jig feet is bounded with lug and grounded in
order to make geometrically true surface
Pressure pads
 Used above or below the workpiece depending on size
and shape of workpiece
 Necessary when workpiece contains sharp corners or
irregular surfaces
 Also used to absorb shocks
 Pressure for pads applied by springs,air or hydraulics
 Urethane pads require less space than springs since they
withstand greater pressure with less deflection compared
to springs
washer
 Used for positive clamping force

 They should have hardness value less than
the mating surface
 Used for compensating length in bolt
sizeand to grip the clamping force
 C washer,swing C washer,spherical
washer,lock washer ,internal star washer
Hand grip screws
 Used for positive clamping
 Used to tighten the part
 Cylindrical end,groove end,floating
end are the various types
Wing or fly screws
 used for light positive tightening
 Cylindrical end,groove end,floating
end are the various types
Quarter turn screw
 Also called thumbscrew latch
 Designed in such a way that the operator can
easily turn the screws even if the threads are
covered with dry oil,dust and chips
 It is kept perpendicular to confirm tightening
Sight Locators:
 Used for rough machining.

 Less accurate.
 Work fits into specific slots on the locating plate
known as sighting plates.
 2 types
Sight location by slots on the table.
Sight location by lines etched on the tool.
Manufacturing Tooling
5. Jig Design
Nageswara Rao
Posinasetti
Fixture
A fixture is a means through which a
part is securely fastened to the
machine tool table to accurately locate,
support and hold the part during the
machining operation.
February 12, 2008 Nageswara Rao Posinasetti 2
Jig
A jig is a special class of fixture, which
in addition to provide all the functions
as above, also guides the cutting tool
during machining.
This is generally used for the
operations such as drilling, boring,
reaming, tapping, counter boring, etc.
1
Typical jig used for boring operation
2
Drill Jigs
Provide methods for
– Correctly locate the workpiece with
respect to the tool
– Securely clamp and rigidly support the
workpiece during the operation
– Guide the tool
– Position and/or fasten the jig on a
machine
Drill Jigs
Advantages
– Minimize tool breakage
– Minimize the possibility of human error
– Permit the use of less skilled labor
– Reduce manufacturing time
– Eliminate retooling for repeat orders
Machine Considerations
Horsepower
Size limitations
Weight limitations
Cutting Tools
Special Machinery
3
Process Considerations
Type of Operations (drilling,reaming,
other)
Number of Operations
– Similar vs. different
– Sequential vs. simultaneous
Sequence
Inspection Requirements
Jig Bushes
To position and guide the cutting tool
for cutting.
Materials
– Hardened steel
– Carbide
– Bronze
– Stainless steel
Headless Bush
Most popular and
least expensive
Light axial load is
expected
4
Clearance between Bush and Part
Headed Drill Bush
Jig plate can be thinner
5
Slip Renewable Bush

Used for multiple
operations such as
Drilling followed by
reaming
6
7
Drill bushing position for angular drill entry
Fig. 5.43 Drilling irregular work surfaces
8
9
Jig Components
Locators
Clamps
Jig plate with bushes
Jig body
Other elements as required
– Supports
– Jig feet
Types of Jigs
Template jigs
Plate jigs
Universal jigs
Leaf jigs
Channel and tumble jigs
Indexing jigs
Miscellaneous jigs
Template jigs
No clamping arrangement
Plates with bushing to guide the tool
Directly placed on the part
Simple
Least expensive
10
Nesting Template Drill Jigs
Template jigs
Disadvantages
– Not as foolproof as other types
– Orientation of the hole pattern to
workpiece datums may not be as accurate
as other types
– They are usually not practical when
locating datums are dimensioned
11
Plate jigs
A template jig with workpiece clamping
system
Plate Jig
Plate Drill Jig
12
Fig. 5-7 Plate jigs
Fig. 5-7 Plate jigs
13
Fig. 5-7 Plate jigs
14
Fig 5-8 Angle plate jigs
15
Fig 5-8 Angle plate jigs
16
Universal jigs
Also called as Pump jigs
Universal that can be used for any
given part by adding the necessary
locators and bushes
17
Leaf jigs
Small
Hinged leaf with bushes which also
applies the clamping force
18
19
Channel and tumble jigs

For drilling in more than one surface
Complicated and expensive
20
21
The example illustrated was designed to drill 4
holes equi-spaced around the tapered hub of a
hand-wheel at right angles to the hub diameter.
Indexing jigs
To drill holes in a pattern
Indexing arrangement
22
23
Miscellaneous jigs
24
Drill Jig with R H Component
Drill Jig with L H Component
25
Drill Jig with R H Component unassembled
Drill Jig with R H and L H Components

simultaneously
26
Pot Drill Jig
Pot Drill Jig
27
28
Jig Design Guidelines
Drill Jigs should be of light
construction, consistent with rigidity to
facilitate handling, especially when jigs
have to be turned over so that holes
can be drilled from more than one side.
All unnecessary metal should be cored
out of the jig body.

A jig which is not bolted to the machine table
should be provided with feet, preferably four,
opposite all surfaces containing guide
bushings, so that it will 'rock' if not standing
square on the table and so warn the
operator.
Clearance holes or burr slots should be
provided in the jig to allow for the burr
formed when the drill breaks through the
component and for swarf clearance,
particularly fromNageswara
locating faces.
Rao Posinasetti
February 12, 2008 86

Make all component clamping devices as
quick acting as possible.
Design the jig fool-proof by the use of foul
pins and similar devices, that is arrange it so
that the component, tools or bushes cannot
be inserted except in the correct way.
Make some locating points adjustable when
the component is a rough casting and may
be out of alignment.
29
Locate clamps so that they will be in the best
position to resist the pressure of the cutting
tool when at work.
If possible, make all clamps integral parts of
the jig and avoid the use of loose parts.
Avoid complicated clamping and locating
arrangements which are liable to wear or
need constant attention.

Place all clamps as nearly as possible
opposite some bearing point of the
component to avoid springing the
component and in accessible positions.
All sharp edges should be removed from the
various detail parts of the jig.
Provide handles or other devices wherever
these will make the handling of the jig more
convenient.

If possible, place all tool guide bushings
inside the geometrical figure formed by
connecting the points of location of the feet.
Make, if possible, all locating points visible to
the operator when placing the component in
position in the jig so that the component can
be seen to be correctly located. The operator
should also be able to have an unobstructed
view of the clamps.
30
Before using the jig in the machine shop for
commercial purposes, test all jigs as soon as
they are made.
The location points, which are hardened if
necessary, are established with
considerations to machining operations, if
any, to follow and that any mating parts are
located from the same datum surface.

Locating and clamping arrangements are
designed to reduce idle time to a minimum
by using simple clamps which are easy and
quick to operate and also operate without
damaging the component.
Springs should be used whenever possible
to elevate the clamps clear of the component
whilst being loaded or unloaded.

Clamps should be positioned above
the points supporting the component,
in order to avoid distortion and should
be strong enough to hold the
component without bending.
Generally clamps should not be relied
upon for holding the work against the
pressure exerted by the cutting tool.
31
Locating and supporting surfaces
should, whenever possible, be
renewable.
– Such surfaces should be of hard material.

The process of inserting and
withdrawing the component from the jig
should be as easy as possible.
– Ample space should be left between the
jig body and the component for hand
movements.
– Some means of ejection should exist to
release the component if it sticks in the jig.

The design of the jig must be safe.
– Handles or levers should be large enough
to clear adjacent parts so that pinched
fingers are avoided.
32
If necessary, make provision for the
use of coolant.
Position locations at places where
there is no flash or burr on the
component.

If possible, eliminate spanners by the
use of levers.
– If spanners have to be used, make one
spanner fit all the clamp operating bolts
and nuts.
Consideration should be given at the
design stage to the use of standardised
jig components.
Power requirement for Drilling
Torque, M = K A f 0.8 d 1.8

Thrust , T = 2 K B f 0.8 d 0.8 + K E d 2
d = drill diameter, in
K, A, B, E - Constants
33
34
35
Basic Design Steps
1. Method of locating the part – identify the
standard components required for locating
purpose.
2. Design the clamping method. Make a
proper choice of clamps – C-washer, swing
washer, nut, strap clamp, toggle clamp, etc.
3. Design any supports required
4. Design the jig bushes required.
5. Design the jig body.
Design Study – Drill Jig
1. Method of locating the part – The

central hole which helps in locating as
well as indexing for the hole.
2. Clamping can be done with a nut
and a C-washer
Indexing will have to be done with a
plunger type retracting.
For locating 5/8 in

hole
For
locating
in the jig
body
36
For locating 5/8 in
hole
For
locating
in the jig
body
37
38
39
40
41
42
43
International Journal of Engineering Research and General Science Volume 2, Issue 2, Feb-Mar 2014
ISSN 2091-2730
A Review on Design of Fixtures

Shailesh S.Pachbhai1, Laukik P.Raut2
1
Research Scholar, Department of Mechanical Engineering, G.H.Raisoni college of Engineering, Nagpur 440016
2
Assistant Professor, Department of Mechanical Engineering, G.H.Raisoni college of Engineering, Nagpur 440016
Email- [email protected]
ABSTRACT - In machining fixtures, minimizing workpiece deformation due to clamping and cutting forces is essential
to maintain the machining accuracy. The various methodology used for clamping operation used in different application
by various authors are reviewed in this paper. Fixture is required in various industries according to their application. This can be
achieved by selecting the optimal location of fixturing elements such as locators and clamps. The fixture set up for component is done
manually. For that more cycle time required for loading and unloading the material. So, there is need to develop system which can
help in improving productivity and time. Fixtures reduce operation time and increases productivity and high quality of operation is
possible.
keywords: fixture, accuracy, clamping, productivity.
I. INTRODUCTION
The fixture is a special tool for holding a work piece in proper position during manufacturing operation. For supporting and
clamping the work piece, device is provided. Frequent checking, positioning, individual marking and non-uniform quality in
manufacturing process is eliminated by fixture. This increase productivity and reduce operation time. Fixture is widely used in the
industry practical production because of feature and advantages.
To locate and immobilize workpieces for machining, inspection, assembly and other operations fixtures are used. A fixture
consists of a set of locators and clamps. Locators are used to determine the position and orientation of a workpiece, whereas clamps
exert clamping forces so that the workpiece is pressed firmly against locators. Clamping has to be appropriately planned at the stage of
machining fixture design. The design of a fixture is a highly complex and intuitive process, which require knowledge. Fixture design
plays an important role at the setup planning phase. Proper fixture design is crucial for developing product quality in different terms
of accuracy, surface finish and precision of the machined parts In existing design the fixture set up is done manually, so the aim of this
project is to replace with hydraulic fixture to save time for loading and unloading of component. Hydraulic fixture provides the
manufacturer for flexibility in holding forces and to optimize design for machine operation as well as process functionability.
Steps of fixture design
Successful fixture designs begin with a logical and systematic plan. With a complete analysis of the fixture's functional
requirements, very few design problems occur. When they do, chances are some design requirements were forgotten or
underestimated. The workpiece, processing, tooling and available machine tools may affect the extent of planning needed.
Preliminary analysis may take from a few hours up to several days for more complicated fixture designs. Fixture design is a five-
step problem-solving process. The following is a detailed analysis of each step.
Step 1: Define Requirements
To initiate the fixture-design process, clearly state the problem to be solved or needs to be met. State these requirements
as broadly as possible, but specifically enough to define the scope of the design project. The designer should ask some basic
questions: Is the new tooling required for first-time production or to improve existing production?
Step 2: Gather/Analyze Information
Collect all relevant data and assemble it for evaluation. The main sources of information are the part print,
126 www.ijergs.org
ISSN 2091-2730
process sheets, and machine specifications. Make sure that part documents and records are current. For example, verify that
the shop print is the current revision, and the processing information is up-to-date. Check with the design department for
pending part revisions. An important part of the evaluation process is note taking. Complete, accurate notes allow designers
to record important information. With these notes, they should be able to fill in all items on the "Checklist for Design
Considerations." All ideas, thoughts, observations, and any other data about the part or fixture are then available for later
reference. It is always better to have too many ideas about a particular design than too few. Four categories of design
considerations need to be taken into account at this time: workpiece specifications, operation variables, availability of
equipment, and personnel. These categories, while separately covered here, are actually
interdependent. Each is an integral part of the evaluation phase and must be thoroughly thought out before beginning the
fixture design.
Step 3: Develop Several Options
This phase of the fixture-design process requires the most creativity. A typical workpiece can be located and
clamped several different ways. The natural tendency is to think of one solution, then develop and refine it while blocking
out other, perhaps better solutions. A designer should brainstorm for several good tooling alternatives, not just choose one
path right away. During this phase, the designer's goal should be adding options, not discarding them. In the interest of
economy, alternative designs should be developed only far enough to make sure they are feasible and to do a cost estimate.
The designer usually starts with at least three options: permanent, modular, and general-purpose workholding. Each of these
options has many clamping and locating options of its own. The more standard locating and clamping devices that a designer
is familiar with, the more creative he can be. Areas for locating a part include flat exterior surfaces (machined and
unmachined), cylindrical and curved exterior surfaces. The exact procedure used to construct the preliminary design sketches
is not as important as the items sketched. Generally, the preliminary sketch should start should start with the part to be
fixtured. The required locating and supporting elements, including a base, should be the next items added. Then sketch the
clamping devices. Finally, add the machine tool and cutting tools. Sketching these items together helps identify any problem
areas in the design of the complete fixture.
Step 4: Choose the Best Option
The total cost to manufacture a part is the sum of per-piece run cost, setup cost, and tooling cost. Expressed as a
formula:
These variables are described below with sample values from three tooling options: a modular fixture, a
permanent fixture, and a hydraulically powered permanent fixture.
Step 5: Implement the Design
The final phase of the fixture-design process consists of turning the chosen design approach into reality. Final
details are decided, final drawings are made, and the tooling is built and tested. The following guidelines should be
considered during the final-design process to make the fixture less costly while improving its efficiency. These rules are a
mix of practical considerations, sound design practices, and common sense [9].
i. Use standard components: The economies of standard parts apply to tooling components as well as to manufactured
products. Standard, readily available components include clamps, locators, supports, studs, nuts, pins and a host of other
elements. Most designers would never think of having the shop make cap screws, bolts or nuts for a fixture. Likewise, no
standard tooling components should be made in-house. The first rule of economic design is: Never build any component you
can buy. Commercially available tooling components are manufactured in large quantities for much greater economy. In
127 www.ijergs.org
ISSN 2091-2730
most cases, the cost of buying a component is less than 20% of the cost of making it.
Labor is usually the greatest cost element in the building of any fixture. Standard tooling components are one
way to cut labor costs. Browse through catalogs and magazines to find new products and application ideas to make designs
simpler and less expensive.
ii. Use prefinished materials: Prefinished and preformed materials should be used where possible to lower costs and
simplify construction. These materials include precision-ground flat stock, drill rod, structural sections, cast tooling sections,
precast tooling bodies, tooling plates, and other standard preformed materials. Including these materials in a design both
reduces the design time and lowers the labor cost.
iii. Eliminate finishing operations: Finishing operations should never be performed for cosmetic purposes. Making a
fixture look better often can double its cost. Here are a few suggestions to keep in mind with regard to finishing operations.
iv. Keep tolerances as liberal as possible: The most cost-effective tooling tolerance for a locator is approximately 30% to
50% of the workpiece's tolerance. Tighter tolerances normally add extra cost to the tooling with little benefit to the process.
Where necessary, tighter tolerances can be used, but tighter tolerances do not necessarily result in a better fixture, only a
more expensive one.
II .IMPORTANT CONSIDERATIONS WHILE DESIGNING JIGS AND FIXTURES.
Designing of jigs and fixtures depends upon so many factors. These factors are analyzed to get design inputs for jigs and
fixtures. The list of such factors is mentioned below :
a. Study of workpiece and finished component size and geometry.
b. Type and capacity of the machine, its extent of automation.
c. Provision of locating devices in the machine.
d. Available clamping arrangements in the machine.
e. Available indexing devices, their accuracy.
f. Evaluation of variability in the performance results of the machine.
g. Rigidity and of the machine tool under consideration.
h. Study of ejecting devices, safety devices, etc.
i. Required level of the accuracy in the work and quality to be produced.
III. MEANING OF LOCATION
The location refers to the establishment of a desired relationship between the workpiece and the jigs or
fixture correctness of location directly influences the accuracy of the finished product. The jigs and fixtures are desired so
that all undesirable movements of the workpiece can be restricted. Determination of the locating points and clamping of the
workpiece serve to restrict movements of the component in any direction, while setting it in a particular pre-decided position
relative to the jig. Before deciding the locating points it is advisable to find out the all possible degrees of freedom of the
workpiece. Then some of the degrees of freedom or all of them are restrained by making suitable arrangements. These
arrangements are called locators. These are described in details below[11]:
128 www.ijergs.org
ISSN 2091-2730
1.PRINCIPLES OF LOCATIONS
The principle of location is being discussed here with the help of a most popular example which is available
in any of the book covering jigs and fixtures. It is important that one should understand the problem first. Any rectangular
body many have three axis along x-axis, y-axis and z-axis. It can more along any of these axes or any of its movement can
be released to these three axes. At the same time the body can also rotate about these axes too. So total degree of freedom of
the body along which it can move is six. For processing the body it is required to restrain all the degree of freedom (DOF)
by arranging suitable locating points and then clamping it in a fixed and required position. The basic principle used to locate
the points is desirable below. Six Points Location of a Rectangular Block. It is made to rest on several points on the jig body.
Provide a rest to workpiece on three points on the bottom x-y surface. This will stop the movement along z-axis, rotation
with respect to x-axis and y-axis. Supporting it on the three points is considered as better support then one point or two
points. Rest the workpiece on two points of side surface (x-z), this will fix the movement of workpiece along y-axis and
rotation with respect to z-axis. Provide a support at one point of the adjacent surface (y-z) that will fix other remaining free
movements. This principle of location of fixing points on the workpiece is also named as 3-2-1 principle of fixture design as
numbers of points selected at different faces of the workpiece are 3, 2 and 1 respectively. If the operation to be done on the
cylindrical object requires restriction of the above mentioned free movements also than some more locating provisions must
also be incorporated in addition to use of the Vee block. Guohua Qin[1] focuses on the fixture clamping sequence. It
consists of two parts:
a. For the first time he evaluated varying contact forces and workpiece position errors in each clamping step by solving a
nonlinear mathematical programming problem. This is done by minimizing the total complementary energy of the
workpiece-fixture system. The prediction proves to be rigorous and reasonable after comparing with experimental data and
referenced results.
b. The optimal clamping sequence is identified based on the deflections of the workpiece and minimum position error.
Finally, To predict the contact forces and to optimize the clamping sequence three examples are discussed.
Fig. 1 Scheme of 3-2-1 fixture setup [1].
First mathematical modeling for clamping sequence is done then he determined the contact forces in clamping
sequence as shown in fig. 1. After that he optimized of clamping sequence for higher stiffness workpiece and low stiffness
workpiece. He found that with the use of optimal clamping sequence, good agreements are achieved between predicted
129 www.ijergs.org
ISSN 2091-2730
results and experimental data and the workpiece machining quality can be improved .
For a fixture designer, the major portion of design time is spent deciding how to locate the work piece in the
fixture. You know that any free body has a total of twelve degrees of freedom as below:
6 translational degrees of freedom: +X, -X, +Y, -Y, +Z, -Z
And 6 rotational degrees of freedom:
- Clockwise around X axis (CROT-X)
- Anticlockwise around X axis (ACROT-X)
- Clockwise around Y axis (CROT-Y)
- Anticlockwise around Y axis (ACROT-Y)
- Clockwise around Z axis (CROT-Z)
- Anticlockwise around Z axis (ACROT-Z)
You must fix all the 12 degrees of freedom except the three transitional degrees of freedom (-X, -Y and -Z) in
order to locate the work piece in the fixture. So, 9 degrees of freedom of the work piece need to be fixed. But, how? By
using the 3-2-1 method as shown below in fig. 2 :
Fig. 2 Available Degree of Freedom of Rectangular Block[11]
Now, rest the work piece at two points of side surface (XZ), and you will be able to fix the +Y and ACROT-Z
degrees of freedom. Now, rest the work piece at one point of the adjacent surface (YZ), and you will be able to fix the +X
and CROT-Z degrees of freedom. So, you can successfully fixate 9 required degrees of freedom by using the 3-2-1
principle of fixture design.
Nicholas Amaral [6] develop a method for modeling workpiece boundary conditions and applied loads during a
machining process, optimize support locations, using finite element analysis (FEA) and analyses modular fixture tool
contact area deformation. The workpiece boundary conditions are defined by locators and clamps. To constrain using linear
spring-gap elements the locators are placed in a 3-2-1 fixture configuration and modeled using all degrees of freedom of the
workpiece. To model cutting forces during drilling and milling machining operations, the workpiece is loaded. Fixture
design integrity is verified. To develop an algorithm to automatically optimize fixture support and clamp locations. To
minimize deformation in workpiece, subsequently increasing machining accuracy ANSYS parametric design language code
is used. Unnecessary and uneconomical “trial and error” experimentation on the shop floor is eliminated by implementing
130 www.ijergs.org
ISSN 2091-2730
FEA in a computer-aided-fixture-design environment.
2. DIFFERENT METHODS USED FOR LOCATION
There are different methods used for location of a work. The locating arrangement should be decided after studying
the type of work, type of operation, degree of accuracy required. Volume of mass production to be done also mattes a lot.
Different locating methods are described below.:
Flat Locator
Flat locators are used for location of flat machined surfaces of the component. Three different examples
which can be served as a general principle of location are described here for flat locators. These examples are illustrated in
Fig. 3
Fig. 3 Flat locator[11]
A flat surface locator can be used as shown in first figure. In this case an undercut is provided at the bottom
where two perpendicular surfaces intersect each other. This is made for swarf clearance. The middle figure shows flat
headed button type locator. There is no need to made undercut for swarf clearance. It is used for locating components having
drilled holes. The cylindrical component to be located is gripped by a cylindrical locator fitted to the jig‟s body and inserted
in the drilled hole of the component.
Jack Pin Locator
Jack pin locator is used for supporting rough workpieces from the button as shown in Fig. 4. Height of the
jack pin is adjustable to accommodate the workpieces having variation in their surface texture. So this is a suitable method
to accommodate the components which are rough and un-machined.
Fig. 4 Jack Pin Locator[11]
131 www.ijergs.org
ISSN 2091-2730
Drill Bush Locator
The drill bush locator is used for holding and locating the cylindrical workpieces. The bush has conical
opening for locating purpose and it is sometimes screwed on the jigs body for the adjustment of height of the work.
Fig. 5 Drill Bush Locator[11]
Vee Locators
This is quick and effective method of locating the workpiece with desired level of accuracy. This is used for locating
the circular and semi-circular type of workpiece. The main part of locating device is Vee shaped block which is normally
fixed to the jig. This locator can be of two types fixed Vee locator and adjustable Vee locator. The fixed type locator is
normally fixed on the jig and adjustable locator can be moved axially to provide proper grip of Vee band to the workpiece.
Fig. 6 Vee Locator[11]
Locating error and machining error were studied by systematic method of error identification and calculation, in
which. using finite element analysis (FEA). The machining error, the surface error shown in fig. 7 generated from machining
operations by Y. Wang [7].
Fig. 7 Surface error sources [7].
A methodology of machined surface error calculation and error decomposition was presented in this paper. The research has
132 www.ijergs.org
ISSN 2091-2730
focused on (a) surface error including both locating error and machining error, also machining error generated during multi
machining operations was analyzed; (b) the sensitivity of individual errors was investigated, and the resultant surface error
of locating and machining was evaluated against tolerance; and (c) the method is suitable for both components with complex
geometry as well as simple geometry.
Fig. 8 Tolerance of the sample feature [7]
The surface error analysis of a sample feature of turbine blades was presented to demonstrate the developed
procedure and analysis. The result suggested that the component does not satisfy the tolerance requirement due to fixture
related errors such as clamping deformation shown in fig. 8, workpiece movement, and workpiece twist. The methods of
error reduction were proposed
IV. CLAMPING
To restrain the workpiece completely a clamping device is required in addition to locating device and jigs and
fixtures. A clamping device holds the workpiece securely in a jig or fixture against the forces applied over it during on
operation. Clamping device should be incorporated into the fixture, proper clamp in a fixture directly influence the accuracy
and quality of the work done and production cycle time. Basic requirement of a good clamping device are listed below :
a. It should rigidly hold the workpiece.
b. The workpiece being clamped should not be damaged due to application of clamping pressure by the clamping unit.
c. The clamping pressure should be enough to overcome the operating pressure applied on the workpiece as both pressure
act on the workpiece in opposite directions.
d. Clamping device should be capable to be unaffected by the vibrations generated during an operation.
e. It should also be user friendly, like its clamping and releasing should be easy and less time consuming. Its maintenance
should also be easy.
f. Clamping pressure should be directed towards the support surfaces or support points to prevent undesired lifting of
workpiece from its supports.
g. Clamping faces should be hardened by proper treatments to minimize their wearing out.
133 www.ijergs.org
ISSN 2091-2730
h. To handle the workpieces made of fragile material the faces of clamping unit should be equipped with fiber pads to avoid
any damage to workpiece.
J. Cecil[5] proposed an innovative clamping design approach is described in the context of fixture design
activities. The clamping design approach involves identification of clamping surfaces and clamp points on a given
workpiece. This approach can be applied in conjunction with a locator design approach to hold and support the workpiece
during machining and to position the workpiece correctly with respect to the cutting tool. Detailed steps are given for
automated clamp design. Geometric reasoning techniques are used to determine feasible clamp faces and positions. The
required inputs include CAD model specifications, features identified on the finished workpiece, locator points and
elements.
1.DIFFERENT TYPES OF CLAMPS
Different variety of clamps used with jigs and fixtures are classified into different categories are discussed here:
Strap Clamp
This is also called edge clamp. This type clamping is done with the help of a lever pressure acting as a strap on the
workpiece. Different types of strap clamps are discussed below.
Heel Clamp
Rotation of the clamp in clockwise direction is prevented and it is allowed in anticlockwise direction. For releasing
the workpiece the clamping nut is unscrewed. The free movements in anticlockwise direction takes place before un-securing
the nut to release the workpiece.
Fig. 9 Heel Clamp[11]
Bridge Clamp
The bridge clamp applies more clamping pressure as compared to heel clamp. The clamping pressure experienced by
the workpiece depends on the distances „x‟ and „y‟ marked. To release the workpiece the nut named as clamping nut is
unscrewed. The spring lifts the lever to release the workpiece.
134 www.ijergs.org
ISSN 2091-2730
Fig. 10 Bridge Clamp
Edge Clamp or Side Clamp
A side clamp is also known as edge clamp. In this case the surface to be machined is always clamped above the
clamping device. This clamping device is recommended for fixed length workpiece. Releasing and clamping of the
workpiece can be accomplished by unscrewing and screwing of the clamping nut respectively.
Fig. 11 Edge Clamp or Side Clamp[11]
Screw Clamp
The screw clamp is also known as clamp screw. This clamping apply pressure directly on the side faces of the
workpiece.
Fig. 12 Screw Clamp[11]
135 www.ijergs.org
ISSN 2091-2730
There is a floating pad at their end to serve the following purposes :
a. It prevents displacement of workpiece and slip.
b. It prevents denting of clamping area of workpiece.
c. The available cushion prevents deflection of screw.
In addition to the above there are some disadvantages associated with this method. The clamping pressure largely
depends on the workpiece; it varies from one workpiece to other. It is more time consuming and more efforts are required.
Latch Clamp
Latch clamps are used to clamp the workpiece, the clamping system is normally locked with the help of a latch
provided. To unload the workpiece the tail end of the latch is pushed that causes the leaf to swung open, so releasing the
workpiece. Here time consumed in loading and unloading is very less as no screw is tightened but clamping pressure is not
so high as in other clamping devices. Life of this type of clamping device is small.
Equalizing Clamps
Equalizing clamp is recommended to apply equal pressure on the two faces of the work. The pressure applied can be
varied by tightened or loosening the screw provided for the purpose.
Fig. 13 Equalizing Clamps[11]
Power Driven Clamping
Light duty clamps are used manually because small power is required to operate these clamps. Hand clamping leads
to application of variable pressure, operator‟s fatigue and more time consumed. The power driven clamping over comes the
above mentioned problems of hand clamping. Power clamps are operated on the base of hydraulic or pneumatic power.
Power clamps are high pressure clamping, these are quick acting, easily controllable, reliable and less time consuming.
136 www.ijergs.org
ISSN 2091-2730
V. SOFTWARE FOR FIXTURE DESIGN
NX streamlines the entire tool development process including part design, tool assembly layout, and detailed
tooling design and validation. Using NX‟s advanced functionality, step-by-step guidance and associatively with part designs,
you can work with even the most challenging tooling and fixture designs. These are discussed below[10]
Fig. 14 NX Mold Design[10]
NX Mold Design shown in fig. 14 automates and streamlines the entire mold development process including part
design, tool design and motion validation. You can ensure fast response to design changes and high-quality molds.
Fig. 15 NX Progressive Die Design[10]
NX guides you through all of the stages required to design a progressive die, automating the most tedious tasks and
streamlining the most complex processes which is shown in fig.15. NX Progressive Die Design is a comprehensive solution
for both straight break and freeform sheet metal parts. You can design the complete die structure with associatively to the
part design at every stage.
137 www.ijergs.org
ISSN 2091-2730
Fig. 16 NX Stamping Die Design[10]
The advanced capabilities in NX for designing automotive stamping dies include formability analysis, die
planning, die face design, detailed die structure design and die validation. NX Stamping Die Design guides you in defining
the process used to manufacture complex stamped sheet metal parts, producing a representation of the press line and
modeling the shape of the sheet metal as it leaves each press.
Fig. 17 NX Electrode Design[10]
NX Electrode Design incorporates numerous industry best practices into a step-by-step approach that automates the
electrode design and manufacturing process.
Fig. 18 NX for Jig and Fixture Design[10]
Because jig and fixture designs are fully associative to the part model, you can quickly and accurately update
fixtures based on part model changes. You can easily position and mate fixture components with the NX assembly
capabilities, and then automatically create drawings and documentation for the fixture and its components. NX also allows
you to simulate the kinematics of fixtures, such as opened and closed positions, and check for strength and distortion.
138 www.ijergs.org
ISSN 2091-2730
Michael Stampfer[2] presented a paper which deals with the problem of setup and fixture planning for the
machining of box-shaped parts on the horizontal machining centers. The setup and fixture planning shown in fig. 2. The
central topic of this research is the automation of the conceptual design of fixtures shown in fig. 3. This topic is deal with the
setup planning.
Fig. 19 Integrated process planning and fixture planning system[2].
The integrated handling of tasks of setup and fixture planning and the finding of solution in an integrated system is ,
the main aim of the author. Based on the workpiece model, the setup sequence, the conceptual solution of fixture for each
setup determined automatically by the developed system.
1.Fixturing Functional Requirements
From a layout point of view, fixtures have six basic functional requirements :
(1) Stable resting, (2) accurate localization. (3) support reinforcement, (4) stable clamping, (5) foreclosure(or total restraint)
and (6) quality performance.
139 www.ijergs.org
ISSN 2091-2730
The functions have strong precedence conditions. The first five functions are required at the fixturing stage, and
sequentially. When a workpiece is placed into a fixture, it must first assume a stable resting against the gravity. Then, the
locators should provide accurate localization. Next, supports are moved in place, and finally clamps are activated for the part
immobilization (force-closure). The part location must be maintained in the process of instantiating clamps without
workpiece lift-off. The performance of the fixture is ultimately defined as workpiece geometric error during the
manufacturing stage. The geometric error is mainly determined by the fixture localization accuracy and the workpiece static
and elastic deformation during manufacturing. There are additional constraints to be satisfied such as interference-free and
easy loading and unloading.
2. Design Consideration in Fixtures

a. The main frame of fixture must be strong enough so that deflection of the fixture is as minimum as possible. This
deflection of fixture is caused because of forces of cutting, clamping of the workpiece or clamping to the machine table. The
main frame of the fixture should have the mass to prevent vibration and chatter.
b. Frames may be built from simple sections so that frames may be fastened with screws or welded whenever necessary.
Those parts of the frame that remain permanently with the fixture may be welded. Those parts that need frequent changing
may be held with the screws. In the situation, where the body of fixture has complex shape, it may be cast from good grade
of cast iron.
c. Clamping should be fast enough and require least amount of effort.
d. Clamps should be arranged so that they are readily available and may be easily removed.
e. Clamps should be supported with springs so that clamps are held against the bolt head wherever possible.
f. If the clamp is to swing off the work, it should be permitted to swing as far as it is necessary for removal of the workpiece.
g. All locator‟s clamps should be easily visible to the operator and easily accessible for cleaning, positioning or tightening.
h. Provision should be made for easy disposal of chip so that storage of chips doesn‟t interfere with the operation and that
their removal during the operation doesn‟t interfere with the cutting process.
i. All clamps and support points that need to be adjusted with a wrench should be of same size. All clamps and adjustable
support points should be capable of being operated from the fronts of the fixture.
j. Work piece should be stable when it is placed in fixture. If the work piece is rough, three fixed support points should be
used. If work piece is smooth, more than three fixed support points may be used. Support point should be placed as farthest
as possible from each other.
k. The three support points should circumscribe the centre of gravity of the workpiece.
l. The surface area of contact of support should be as small as possible without causing damage to the workpiece. This
damage is due to the clamping or work forces.
The importance of fixture design automation is emphasized by Djordje Vukelic [3]. General structure of the
automated design system shown in fig. 20 with a highlight on the fixture design systems and their main characteristics.
140 www.ijergs.org
ISSN 2091-2730
Fig. 20 Layout of working [3].
It also shows a structure and a part of output results of the automated modular fixture design system. The expert
systems have been mostly used for the generation of partial fixture solutions, i.e., for the selection of locating and clamping
elements.
Shrikant [8] discussed various design and analysis methods in the context of to improve the life of fixture, different
fixture geometries are compared experimentally and are selected. The proposed eccentric shaft fixture will fulfilled
researcher Production target and enhanced the efficiency, fixture reduces operation time and increases productivity, high
quality of operation,
Weifang Chen [4] developed a multi-objective model was established to increase the distributing uniformity of
deformation and to reduce the degree of deformation. The deformation is analyzed by optimizing the finite element method.
To solve the optimization model a genetic algorithm was developed. A satisfactory result was obtained by illustrating an
example, which is superior than the experiential one.
Fig. 21 A real case fixture configuration [4]
The multiobjective model can reduce the machining deformation effectively and improve the distribution
condition. This paper presented a fixture layout design shown in fig. 21 and clamping force optimization procedure based on
the GA and FEM. The optimization procedure is multi-objective: minimizing the maximum deformation of the machined
surfaces and maximizing the uniformity of the deformation. The ANSYS software package has been used for FEM
calculation of fitness values. The combination of GA and FEM is proven to be a powerful approach for fixture design
optimization problems. In this study, both friction effects and chip removal effects are considered. a database is established
to reduce the computation time, for the chromosomes and fitness values, and the meshed workpiece FEA model is
141 www.ijergs.org
ISSN 2091-2730
repeatedly used in the optimization process.
Fig. 22 shows the existing CAD model of fixture which is used for machining of hydraulic lift housing. In this
fixture clamping is done manually so there is extra time loss for loading and unloading operation. To avoid this problem
there is necessity to develop new design to improve the productivity.
Fig. 22 CAD model of complete fixture assembly
• Type of machine
-Vertical machining centre.
• Operations
-Drilling.
-Reaming.
-Champer.
Machining parameter for drilling
• Cutter diameter 18 mm
• Number of flute 4
• Spindle speed 500 rpm
• Feed 0.15 mm/rev
• Radial depth 18 mm
• Projection length 90 mm
Machining parameters for reaming
• Cutter diameter 26 mm
• Number of flute 4
• Spindle speed 120 rpm
• Feed 0.25 mm/rev
• Radial depth 26 mm
• Projection length 90 mm
3.TYPES OF FIXTURE AND ITS INDUSTRIAL APPLICATIONS
142 www.ijergs.org
ISSN 2091-2730
Vise Fixture It is easy to clamp workpiece with regular shape and parallel sides in a vise. However, workpieces
with round or irregular shapes are very difficult to clamp properly. Hence, special jaws are created to hold workpieces with
irregular shape properly and at the same time, it also avoid damage to the important surfaces. Stop pin is used to prevent
bending of the workpiece by the application of clamping force. guide pins are used to secure alignment. When it is necessary
to hold the workpiece firmly in all the direction.
Fig. 23 Vise Fixture[11]

Facing Fixture Milling machines are extensively used for facing seating and mating flat surfaces. Milling is
often the first operation on the workpiece. The workpiece is positioned by three adjustable spherical ended pads „A‟. These
pads are adjusted to suit the variation in the size of workpiece and lock in the position by check nuts. Two self adjusting
supports „A‟ are pushed upward by light spring. These springs are used to make sure that the support „A‟ is positively in
contact with the workpiece. Clamping screw is used to lock support „B‟. On tightening the edge clamp, the workpiece is
pushed against the fixed jaw. This jaw is keyed in the fixture body to provide solid support to workpiece against the heavy
thrust developed in the operation. The cutter should be fed to the workpiece in such a manner that the milling thrust should
be directed towards the solid support of fixed jaws. The setting can be set in the path of cutter to set it before starting of
facing operation. Four clamping slots are provided to take care of the heavy forces developed during the operation.
Boring Fixture According to the type of boring operation, boring fixture are used. Boring Fixture may have
characteristics of a drill jig or a mill fixture. The workpiece always has an existing hole which is enlarged by the boring
operation. It may be final or may be preliminary to grinding and other sizing operation.
Fig. 24 Boring Fixture[11]

Face Plate Fixture It can be used conveniently for machining of simple and small components. Addition of
locators and clamps on face plate help in quick location and clamping of workpiece. Face plate fixture is useful for facing
143 www.ijergs.org
ISSN 2091-2730
number of workpieces simultaneously on the lathe.
Turning Fixture These are generally special face plates. Their swing should be lesser than the swing of the
machine. These are used for quick location and clamping. Typical turning fixture . The workpiece rests on angle plate and its
boss is centralized with machine axis by sliding v-block which can be operated with knurled screw. The overhang of turning
fixtures should be minimum bare necessary for the operation. Fixture should be balanced with workpiece in position.
Fig. 25 Turning Fixture[11]

The clamping arrangement should be capable of withstanding the various forces developed during operation.
a. Cutting force tangential to cutting circle.
b. Axial force and radial force due to feed of tool.
c. Bending forces due to pressure of tool on workpiece.
Back Plate for Turning Fixture It consists of workpiece locating and clamping elements. These fixtures are
generally used for facing turning and boring operation. The workpiece should be located correctly with respect to rotating
machine spindle for all these operations.
Grinding Fixture The standard magnetic tables are used to rest workpiece such that resting surface will be parallel
to the surface to be ground. However, for light workpiece with lesser resting area, the resting area tends to tilt and fly off the
magnetic table due to high speed of grinding wheel and due to high feed, also. Hence, it is necessary to provide additional
support by nesting the workpiece. This can be done by placing the solid plates around the workpiece. The nest plates are
held firmly by the magnetic force of table with more weight and more resting area. The nest plates surround the workpiece
from outside and arrest its movement in the horizontal plane. Thus, this arrangement will help in preventing it from flying
off and tilting due to high speed and feed in grinding operation.
Fig. 26 Grinding Fixture[11]
144 www.ijergs.org
ISSN 2091-2730
VI.HYDRAULIC CLAMPING
Hydraulic clamping is actuated by cylinders. Clamping fixtures mainly consist of clamping nut which is attached
to cylinder ram. A Pressurized fluid pulls ram and clamps against workpiece. Unclamping, port connected to unpressurized
discharge line. For clamping and unclamping we use three way direction control valve, lever and pedal.
MULTIPLE CLAMPING
Single direction control valve can actuate number of clamps through number of cylinders to pressure or discharge
lines. Clamping pressure is varied by regulating pressure of fluid.
High pressure – heavy roughing cut
Low pressure – light finish cut.
A risk of sudden pressure drop in event of power failure can be countered by provision of non return valve in pressure
supply line.
AIR ASSISTED HYDRAYLIC WORK HOLDING
It is divided into three groups of components. First group of component, the shop air system (6-12bar) provides
power, in the form of pneumatic pressure. Shop air(pressurized air) system consists of air inlet, filter/regulator/lubricator
device, the safety valve /release valve. The second group of component is hydraulic booster consists of booster, check valve,
and manifold. The final group is clamping system- hold, position, and support work piece.
Fig. 23 Hydraulic workholding system.
Shop air is just used for boosting .In addition electric booster and hydraulic pump are used to air- operated
booster system. Hydraulic pump is used for larger applications. Accumulator is installed between clamps and power source
which maintain the necessary pressure when power is disconnected
VII. Conclusion
The efficiency and reliability of the fixture design has enhanced by the system and the result of the fixture design
145 www.ijergs.org
ISSN 2091-2730
has made more reasonable. To reduce cycle time required for loading and unloading of part, this approach is useful. If
modern CAE, CAD are used in designing the systems then significant improvement can be assured. To fulfill the multi-
functional and high performance fixturing requirements optimum design approach can be used to provide comprehensive
analyses and determine an overall optimal design. Fixture layout and dynamic clamping forces optimization method based
on optimal fixture layout could minimize the deformation and uniform the deformation most effectively .The proposed
fixture will fulfilled researcher production target and enhanced the efficiency, Hydraulic fixture reduces operation time and
increases productivity, high quality of operation, reduce accidents.
REFERENCES:
1. Guohua Qin, Weihong, Zhang Min Wan “Analysis and Optimal Design of Fixture Clamping Sequence ASME for
publication in the JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING, 2006.
2. Michael Stampfer “Automated setup and fixture planning system for box-shaped Parts” International Journal of Advance
Manufacturing Technology 45:540–552 DOI 10.1007/s00170-009-1983-1, 2008.
3. Djordje Vukelic, Uros Zuperl & Janko Hodolic “Complex system for fixture selection, modification, and design” Int J
Adv Manuf Technol 45:731–748 DOI 10.1007/s00170-009-2014-y, 2009
4. Weifang Chen ,Lijun Ni & Jianbin Xue “Deformation control through fixture layout design and clamping force
optimization” Int J Adv Manuf Technol 38:860–867 DOI 10.1007/s00170-007-1153-2,2008
5. J. Cecil “A Clamping Design Approach for Automated Fixture Design” Int J Adv Manuf Technol 18:784–789,2008
6. Nicholas Amaral · Joseph J. Rencis · Yiming (Kevin) Rong “Development of a finite element analysis tool for fixture
design integrity verification and optimization” Int J Adv Manuf Technol 25: 409–419, 2005
7. Y. Wang, X. Chen. N, Gindy “Surface error decomposition for fixture development” Int J Adv Manuf Technol DOI
10.1007/s00170-005-0270-z, 2007
8. Shrikant.V.Peshatwar, L.P Raut “Design and development of Fixture for eccentric shaft: A Review” International Journal
of Engineering Research and Applications (IJERA) ISSN: 2248-9622 Vol. 3, Issue 1, February 2013.
9. http://www.carrlane.com/Articles/StPartCL.cfm
10.http://www.plm.automation.siemens.com/en_us/products/nx/for-manufacturing/tooling-fixture-design
11. http://www.ignou.ac.in/upload/jig.pdf
146 www.ijergs.org
Limit Gauging
UNIT 4 LIMIT GAUGING
Structure
4.1 Introduction
Objectives
4.2 Gauges and their Classifications

4.2.1 Standard Gauges
4.2.2 Limit Gauges
4.3 Working Gauges, Inspection Gauges and Reference Gauges

4.4 Gauges for Checking Elements
4.5 Gauges Commonly used in Production Work
4.5.1 Plug Gauges
4.5.2 Ring Gauges
4.5.3 Taper Gauges
4.5.4 Snap Gauges
4.5.5 Thread Gauges
4.5.6 Form Gauges
4.5.7 Screw Pitch Gauges
4.5.8 Radius and Fillet Gauges
4.5.9 Feller Gauges
4.5.10 Plate and Wire Gauges
4.5.11 Indicating Gauges
4.5.12 Air Gauges
4.6 Summary
4.7 Key Words
4.8 Answers to SAQs
4.1 INTRODUCTION
Gauging, done in manufacturing processes, refers to the method by which it is
determined quickly whether or not the dimensions of the checking parts in production,
are within their specified limits. It is done with the help of some tools called gauges. A
gauge does not reveal the actual size of dimension.
A clear distinction between measuring instruments and gauges is not always observed.
Some tools that are called gauges are used largely for measuring or layout work. Even
some are used principally for gauging give definite measurement.
High carbon and alloy steels have been the principal material used for many years.
Objections to steel gauges are that they are subjected to some distortion because of the
heat-treating operations and that their surface hardness is limited. These objections are
largely overcome by the use of chrome plating or cemented carbides as the surface
material. Some gauges are made entirely of cemented carbides or they have cemented
carbides inserted at certain wear points.
Objectives
After studying this unit, you should be able to
 understand the fundamental of the gauges and their classifications, and
 explain the working principles of various types of gauges and their
applications. 43
Metrology and
Instrumentation 4.2 GAUGES AND THEIR CLASSIFICATIONS
Gauges are the tools which are used for checking the size, shape and relative positions of
various parts but not provided with graduated adjustable members. Gauges are,
therefore, understood to be single-size fixed-type measuring tools.
Classifications of Gauges
(a) Based on the standard and limit
(i) Standard gauges
(ii) Limit gauges or “go” and “not go” gauges
(b) Based on the consistency in manufacturing and inspection
(i) Working gauges
(ii) Inspection gauges
(iii) Reference or master gauges
(c) Depending on the elements to be checked
(i) Gauges for checking holes
(ii) Gauges for checking shafts
(iii) Gauges for checking tapers
(iv) Gauges for checking threads
(v) Gauges for checking forms
(d) According to the shape or purpose for which each is used
(i) Plug
(ii) Ring
(iii) Snap
(iv) Taper
(v) Thread
(vi) Form
(vii) Thickness
(viii) Indicating
(ix) Air-operated
4.2.1 Standard Gauges
Standard gauges are made to the nominal size of the part to be tested and have the
measuring member equal in size to the mean permissible dimension of the part to be
checked. A standard gauge should mate with some snugness.
4.2.2 Limit Gauges
These are also called „go‟ and „no go‟ gauges. These are made to the limit sizes of the
work to be measured. One of the sides or ends of the gauge is made to correspond to
maximum and the other end to the minimum permissible size. The function of limit
gauges is to determine whether the actual dimensions of the work are within or outside
the specified limits. A limit gauge may be either double end or progressive. A double
end gauge has the „go‟ member at one end and „no go‟ member at the other end. The „go‟
member must pass into or over an acceptable piece but the „no go‟ member should not.
The progressive gauge has „no go‟ members next to each other and is applied to a
workpiece with one movement. Some gauges are fixed for only one set of limits and are
said to be solid gauges. Others are adjustable for various ranges.
44
Limit Gauging
4.3 WORKING GAUGES, INSPECTION GAUGES
AND REFERENCE GAUGES
To promote consistency in manufacturing and inspection, gauges may be classified as
working, inspection, and reference or master gauges :
Working Gauges
Working gauges are those used at the bench or machine in gauging the work as it
being made.
Inspection Gauges
These gauges are used by the inspection personnel to inspect manufactured parts
when finished.
Reference Gauges
These are also called master gauges. These are used only for checking the size or
condition of other gauges and represent as exactly as possible the physical
dimensions of the product.
4.4 GAUGES FOR CHECKING ELEMENTS

Hole Gauge
It is used to check the dimensions of the hole present in the element.
Shaft Gauge
It is used to check the dimensions of the shaft.
Taper Gauge
It is used to check the dimensions of the tapers.
Thread Gauge
It is used to check the threading of the element.
Form Gauge
It is used to check the forms of the elements.
4.5 GAUGES COMMONLY USED IN PRODUCTION

WORK
Some of the important gauges which are commonly used in production work have been
discussed as follows :
4.5.1 Plug Gauges
These gauges are used for checking holes of many different shapes and sizes. There are
plug gauges for straight cylindrical holes, tapered, threaded square and splined holes.
Figure 4.1 shows a standard plug gauge used to test the nominal size of a cylindrical
hole. Figure 4.2 shows a double-ended limit plug gauge used to test the limits of size. At
one end, it has a plug minimum limit size, the „go‟ end and; at the other end a plug of
maximum limit, the „no go‟ end. These ends are detachable from the handle so that they
may be renewed separately when worn in a progressive limit plug gauge. The „go‟ and
„no go‟ section of the gauge are on the same end of the handle. Large holes are gauged
with annular plug gauges, which are shell-constructed for light weight, and flat plug
gauges, made in the form of diametrical sections of cylinders.
45
Metrology and
Instrumentation
Figure 4.1 : Standard Ring and Plug Gauges
Figure 4.2 : Progressive and Double Ended Limit Plug Gauges
4.5.2 Ring Gauges

Ring gauges are used to test external diameters. They allow shafts to be checked more
accurately since they embrace the whole of their surface. Ring gauges, however, are
expressive manufacture and, therefore, find limited use. Moreover, ring gauges are not
suitable for measuring journals in the middle sections of shafts. A common type of
standard ring gauge is shown in Figure 4.1. In a limit ring gauge, the „go‟ and „no go‟
ends are identified by an annular groove on the periphery. About 35 mm all gauges are
flanged to reduce weight and facilitate handling.
4.5.3 Taper Gauges

The most satisfactory method of testing a taper is to use taper gauges. They are also used
to gauge the diameter of the taper at some point. Taper gauges are made in both the plug
and ring styles and, in general, follow the same standard construction as plug and ring
gauges. A taper plug and ring gauge is shown in Figure 4.3.
Figure 4.3 : Taper Plug and Ring Gauge
When checking a taper hole, the taper plug gauge is inserted into the hole and a slight
pressure is exerted against it. If it does not rock in the hole, it indicates that the taper
angle is correct.
The same procedure is followed in a ring gauge for testing tapered spindle.
The taper diameter is tested for the size by noting how far the gauge enters the tapered
hole or the tapered spindle enters the gauge. A mark on the gauge show the correct
diameter for the large end of the taper.
To test the correctness of the taper two or three chalk or pencil lines are drawn on the
gauge about equidistant along a generatrix of the cone. Then the gauge is inserted into
the hole and slightly turned. If the lines do not rub off evenly, the taper is incorrect and
the setting in the machine must be adjusted until the lines are rubbed equally all along its
46
length. Instead of making lines on the gauge, a thin coat of paint (red led, carbon black, Limit Gauging
Purssian blue, etc.) can be applied.
The accuracy of a taper hole is tested by a taper limit gauge as shown in Figure 4.4. This
has two check lines „go‟ and „no go‟ each at a certain distance from the end of the face.
The go portion corresponds to the minimum and „no go‟ to the maximum dimension.
GO
NO GO
Figure 4.4 : Limit Taper Plug Gauge
4.5.4 Snap Gauges

These gauges are used for checking external dimensions. Shafts are mainly checked by
snap gauges. They may be solid and progressive or adjustable or double-ended. The most
usual types are shown in Figure 4.5.
GO NO GO
NO GO
GO
Caliper Gauge Double Ended Solid Gauge
Adjustable Gauge
Figure 4.5 : Snap Gauges
(a) Solid or non-adjustable caliper or snap gauge with „go‟ and „no go‟ each is
used for large sizes.
(b) Adjustable caliper or snap gauge used for larger sizes.
This is made with two fixed anvils and two adjustable anvils, one for „go‟
and another for the „no go‟.
The housing of these gauges has two recesses to receive measuring anvils
secured with two screws. The anvils are set for a specific size, within an
available range of adjustment of 3 to 8 mm. The adjustable gauges can be
used for measuring series of shafts of different sizes provided the diameters
are within the available range of the gauge.
(iii) Double-ended solid snap gauge with „go‟ and „no go‟ ends is used for
smaller sizes.
4.5.5 Thread Gauges

Thread gauges are used to check the pitch diameter of the thread. For checking internal
threads (nut, bushes, etc.), plug thread gauges are used, while for checking external
threads (screws, bolts, etc.), ring thread gauges are used. Single-piece thread gauges
serve for measuring small diameters. For large diameters the gauges are made with
removable plugs machined with a tang. Standard gauges are made single-piece. Common
types of thread gauges are shown in Figure 4.6. 47
Metrology and
Instrumentation
l l
GO NO GO
Figure 4.6 : Thread Gauge
Standard plug gauges may be made of various kinds :

(a) Plug gauge with only threaded portion.
(b) Threaded portion on one end and plain cylindrical plug on opposite end to
give correct “core” diameter.
(c) Thread gauge with core and full diameters.
Limit plug gauges have a long-thread section on the „go‟ and a short-threaded section on
the „no go‟ end to correspond to the minimum and maximum limits respectively.
Roller rings gauges, similarly have „go‟ and „no go‟ ends. They may also be solid and
adjustable.
Roller Snap gauges are often used in production practice for measuring external threads.
They comprise a body, two pairs „go‟ rollers and two pairs „no go‟ rollers.
Taper thread gauges are used for checking taper threads. The taper-ring thread gauge are
made in two varieties – rigid (non-adjustable) and adjustable. The “go” non-adjustable
ring gauges are full threaded while the „no go‟ have truncated thread profile.
4.5.6 Form Gauges

Form gauges may be used to check the contour of a profile of workpiece for
conformance to certain shape or form specifications.
Template Gauge
It is made from sheet steel. It is also called profile gauge. A profile gauge may
contain two outlines that represent the limits within which a profile must lie as
shown in Figure 4.7.
Figure 4.7 : A Template Gauge

48
4.5.7 Screw Pitch Gauges Limit Gauging
Screw pitch gauges serve as an everyday tool used in picking out a required screw and
for checking the pitch of the screw threads. They consist of a number of flat blades
which are cut out to a given pitch and pivoted in a holder as shown in Figure 4.8. Each
blade is stamped with the pitch or number of thread per inch and the holder bears an
identifying number designing the thread it is intended for. The sets are made for metric
threads with an angle 60o, for English threads with an angle of 55o.
A set for measuring metric threads with 30 blades has pitches from 0.4 to 0.6 mm and for
English threads with 16 blades has 4 to 28 threads per inch.
In checking a thread for its pitch the closest corresponding gauge blade is selected and
applied upon the thread to be tested. Several blades may have to be tried until the correct
is found.
Figure 4.8 : Screw Pitch Gauge
4.5.8 Radius and Fillet Gauges

The function of these gauges is to check the radius of curvature of convex and concave
surfaces over a range from 1 to 25 mm. The gauges are made in sets of thin plates curved
to different radius at the ends as shown in Figure 4.9. Each set consists of 16 convex and
16 concave blades.
Work
Work
Figure 4.9 : Radius and Fillet Gauges
4.5.9 Feller Gauges

Feller gauges are used for checking clearances between mating surfaces. They are made
in form of a set of steel, precision machined blade 0.03 to 1.0 mm thick and 100 mm
long. The blades are provided in a holder as shown in Figure 4.10. Each blade has an
indication of its thickness. The Indian standard establishes seven sets of feller gauges :
Nos 1, 2, 3, 4, 5, 6, 7, which differ by the number of blades in them and by the range of
thickness. Thin blades differ in thickness by 0.01 mm in the 0.03 to 1 mm set, and by
0.05 mm in the 0.1 to 1.0 mm set.
49
Metrology and To find the size of the clearance, one or two blades are inserted and tried for a fit
Instrumentation between the contacting surfaces until blades of suitable thickness are found.
Figure 4.10 : Feller Gauge
4.5.10 Plate and Wire Gauges

The thickness of a sheet metal is checked by means of plate gauges and wire diameters
by wire gauges. The plate gauge is shown in Figure 4.11. It is used to check the thickness
of plates from 0.25 to 5.0 mm, and the wire gauge, in Figure 4.12, is used to check the
diameters of wire from 0.1 to 10 mm.
Figure 4.11 : Plate Gauge
Figure 4.12 : Wire Gauge
4.5.11 Indicating Gauges

Indicating gauges employ a means to magnify how much a dimension deviates, plus or
minus, from a given standard to which the gauge has been set. They are intended for
measuring errors in geometrical form and size, and for testing surfaces for their true
position with respect to one another. Beside this, indicating gauges can be adapted for
checking the run out of toothed wheels, pulleys, spindles and various other revolving
parts of machines.
Indicating gauges can be of a dial or lever type, the former being the most widely used.
50
4.5.12 Air Gauges Limit Gauging
Pneumatic or air gauges are used primarily to determine the inside characteristics of a
hole by means of compressed air. There are two types of air gauges according to
operation: a flow type and a pressure type gauge. The flow type operates on the principle
of varying air velocities at constant pressure and the pressure type operates on the
principle of air escaping through an orifice.
SAQ 1
(a) What are gauges?
(b) Classify the gauges based on the purposes for which they are used.
(c) What is the difference between standard gauges and limit gauges?
SAQ 2
(a) What are the functions of the following gauges :
(i) Form gauge
(ii) Taper gauge
(iii) Reference gauge
(iv) Feller gauge
(v) Air gauges
(b) Mention the name of the gauge that can be used for checking each of the
following :
(i) Shaft
(ii) Wire
(iii) Wheels
(iv) Pulleys
(v) Screw
(vi) Nut
(vii) Bolt
(viii) Hole
(c) Mention the types of material used for making gauges.
4.6 SUMMARY
Gauging is the method by which it is determined quickly whether or not the dimensions of
the checking parts, in the production, are within their specified limits. The tools which are
used for the same are called gauges.
Materials which are used for making gauges are high carbon and alloy steels, cemented
carbides, etc. 51
Metrology and Gauges can be classified mainly as follows :
Instrumentation
(a) Based on the standard and limit
(i) Standard gauge
(ii) Limit gauge
(b) Based on the consistency in manufacturing process and inspection
(i) Working gauge
(ii) Inspection gauge
(iii) Reference gauge
(c) According to the shape or purpose for which each is used
(i) Plug
(ii) Ring
(iii) Snap
(iv) Taper
(v) Thread
(vi) Form
(vii) Indicating
(viii) Feller
(x) Air-gauges
4.7 KEY WORDS

Standard Gauges : These are made to the nominal size of the parts to
be tested.
Limit Gauges : These are „go‟ and „no go‟ gauges.
Plug Gauges : These are used for checking holes of many different
shapes and sizes.
Ring Gauges : External diameter measuring gauges.
Taper Gauges : Taper testing gauges.
Snap Gauges : These are used for checking shafts.
Thread Gauges : These are used for pitch diameter of the thread.
Form Gauges : These are used to check the contour of a profile.
Feller Gauges : For checking the clearance between the mating
surfaces.
Indicating Gauges : To measure the position of the surfaces.
Air Gauge : To measure inside characteristics of a hole using
air.
4.8 ANSWERS TO SAQs

SAQ 1
(a) Gauges are the tools which are used for checking the size, shape and relative
positions of various parts.
52
(b) (i) Plug gauges Limit Gauging
(ii) Ring gauges

(iii) Taper gauges
(iv) Thread gauges
(v) Snap gauges
(vi) Indicating gauges
(vii) Air gauges
(c) Standard gauges are made to the nominal size of the part to be tested and have
the measuring member equal in size to the mean permissible dimensions of
the part to be checked, whereas the limit gauges are made to the limit sizes of
the work to be measured.
SAQ 2
(a) (i) Gauge : It may be used to check the contour of a profile of a workpiece
for conformance to certain shape or form specifications.
(ii) Taper Gauge : It is used to check the taper. It is also used to measure
the diameter of the taper at some point.
(iii) Reference Gauge : It is used only for checking size or condition of
other gauges.
(iv) Snap Gauge : It is used for checking external diameters. Shafts are
mainly checked by the snap gauges.
(v) Feller Gauge : It is used for checking clearances between mating
surfaces.
(vi) Air Gauges : It is used primarily to determine the inside characteristics
of the hole by means of compressed air.
(b) (i) Shaft : Snap gauges, Ring gauges.
(ii) Wire : Wire gauges.
(iii) Wheels : Indicating gauges.
(iv) Pulleys : Indicating gauges.
(v) Screw : Thread gauges.
(vi) Nut : Thread gauges.
(vii) Bolt : Thread gauges.
(viii) Hole : Plug gauges.
(c) (i) High carbon and alloy steel.
(ii) Cemented carbides.
53

4022510 JFG _ v Sem TD Notes of Lesson

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

4022510 JFG _ v Sem TD Notes of Lesson

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

4022510 JFG _ v Sem TD Notes of Lesson

Uploaded by

Copyright:

Available Formats

Introduction to

JIGS AND FIXTURES

An example of a jig is when a key is duplicated, the original is used as a jig

INTERCHANGEABILITY AND QUALITY:

FOOL PROOF: The design of jigs and fixtures should be such

• WEIGHT OF JIGS AND FIXTURES: It should be easy to handle,

• MATERIALS FOR JIGS AND FIXTURES: Usually made of hardened

 Cleanliness of machining process – Design must be such that not

 Replaceable part or standardization – The locating and supporting

 Provision for coolant – Provision should be there so that the tool is

 Inserts and pads – Should always be riveted to those faces of

 Fool-proofing – Pins and other devices of simple nature

 Easy manipulation – It should be as light in weight as possible

 Initial location – Should be ensured that workpiece is not

 Position of clamps – Clamping should occur directly above

 Ejecting devices – Proper ejecting devices should be incorporated

 Rigidity and stability – It should remain perfectly rigid and stable

 Safety – The design should assure perfect safety of the operator

Locating: dimensional and positional relation-

Locator: device to establish and maintain position of

 They should be placed as far as possible:

locators must be made to suit the MMC

With external features, like shafts, the MMC is

With internal features, like holes, it is the

Redundant, or duplicate, locators should be avoided. b) Both the hub

To restrict the movement of the part

A single pin locator in vertical plane

This is the most common locating method employed for

Flat bases may also be used, but these should be installed

But pin/button type locators offers more accuracy as the area

Locating work from an external

 Work piece with the drilled holes use

 Used for cylindrical workpiece.

 For work pieces other than cylinders.

 For larger work pieces a nest may not be possible

Sphercal location reduces contact

 Relieved locator used in thick workpiece

 Used for positive clamping force

 Used for rough machining.

February 12, 2008 Nageswara Rao Posinasetti 2

February 12, 2008 Nageswara Rao Posinasetti 3

February 12, 2008 Nageswara Rao Posinasetti 6

February 12, 2008 Nageswara Rao Posinasetti 8

February 12, 2008 Nageswara Rao Posinasetti 9

February 12, 2008 Nageswara Rao Posinasetti 11

February 12, 2008 Nageswara Rao Posinasetti 12

February 12, 2008 Nageswara Rao Posinasetti 13

Headed Drill Bush

Jig plate can be thinner

February 12, 2008 Nageswara Rao Posinasetti 14

February 12, 2008 Nageswara Rao Posinasetti 15

February 12, 2008 Nageswara Rao Posinasetti 17

Slip Renewable Bush

February 12, 2008 Nageswara Rao Posinasetti 18

February 12, 2008 Nageswara Rao Posinasetti 20

February 12, 2008 Nageswara Rao Posinasetti 21

Drill bushing position for angular drill entry

February 12, 2008 Nageswara Rao Posinasetti 23