GOODLUCK ENGINEERING CO.

(Unit of Goodluck India Limited)

Works : Khasra No. 2839, Village : Dhoom Manikpur, G.T. Road, Dadri, G.B. Nagar-203207, U.P. (India)

MATERIAL TEST CERTIFICATE

( AS PER EN - 10204 - 3.1 )

CUSTOMER Name CUSTOMER P.O. No. & Dt. Work Order No. & Date. Customer SPCN. No./Rev No. QAP NO./Rev No. DOC. NO.

RELIANCE INDUSTRIES LTD. VILLAGE : MEGHPAR,PADANA/gagva PO-MOTI KHAVDI JAMITP:

363/240775126
Annexure-1A-
10080-1-SS-PP-004
ITP
Pvt/825/24-25
for CS/LTCS Forged/
(PART-III)
Plate
REV.3
flanges
DATED
(including
22.01.2014
Space & Blind) to spec A105, A350 LF2, A515/A51

11/07/24 18.07.2024

STEEL MELTING PROCESS ORDER STATUS DIMENSIONS AS PER

BF-EAF-LRF-VD-CCM/FULLY KILLED & FINE GRAIN PRACTICE

COMPLETE ASME B16.5 (Ed.2020)

Item Code/Part No. ITEM DESCRIPTION Material Specification QUANTITY HEAT NUMBER BATCH No. HEAT TREATMENT

Item Sr.No. CONDITION

(NOS)

1.000 It.Code:2000251011_Eng.Code:FWG1170D
20.0 in x 150 # x WNRF x SCH STD ASTM A105N (ED.2021) 1 M014273B GL11129D Normalized
 : GASKET FACE FINISH: 125-250 AARH MICROFINISH Total Qty Pc 1

C% Mn% Si% S% P% Cr% Ni% Mo%

CHEMICAL TEST M014273B - $0.2100 $1.1800 $0.2000 $0.0040 $0.0130 $0.0250 $0.0060 $0.0010

TEST METHOD : M014273B GL11129D $0.2035 $1.1950 $0.2220 $0.0042 $0.0165 $0.0240 $0.0055 $0.0013

Report Type Heat No Batch No

MECHANICAL TEST REPORT TEST METHOD: A-370 Hardness Impact Test10X10X55 mm (Cha
AT ROOM TEMPERATURE IN TEST METHOD: E-10
TEST METHOD: A
AS DELIVERED CONDITION Batch No Orientation Gauge
Yield Strength ( N / mm sq. ) (0.2%Tensile
Proof Stress)
strength (n/mm Sq.)
Elongation % On GL = 4D Reduction In
Dia / Size (mm) HBW
Area % 01

GL11129D Tangential $12.47 $411.53 $551.98 $34.20 $70.44 164,166

Supporting Testing Test Standard With Edition Acceptance Level

PT (Bevel Ends only) (IN FINISH M/C CONDITION) ASTM E-165 Para 7.5.7.2 of ASME Sec. VIII Div.2 (Ed.2021)

Remark (1) Stock Code, P.O. NO., P.O. Item No. & Heat No. Hard Punched on Flanges by using "Low Stress Stamping". (2) No Weld repair performed on forging. (3) Hardness test carried out o
Identification Mark : WO No.;SR. NO.; GLE; DIMN. STD.;MATL. SPEC.; BATCH No.; HEAT No.; ITEM/STOCK CODE; DP-OK;

We hereby certify that material declared above meets the requirement of P.O./ relevant specification

Prepared by Checked by (Sign & Stamp)

F-QC-09 Rev. No. 00 Issue 02 Page -1 of 1

 Entry No. : 6048

PROJECT: TEST CERTIFICATE No & Dat.e

DDP JAMNAGAR DTA CAPEX GLECO/J-825/5364

Date 31.12.2024

INSPECTION AGENCY DATE OF Inspection & TESTING

M/S. TUV-N 23, 24, 26 TO 28 & 30 TO 31.12.2024

TEMP SOAKING TIME COOLING MEDIUM DELIVERY STATUS

°C (Hrs)

920 04 Hrs Cooled In Still Air Complete

 Cu% V% CE% Al%

$0.0050 $0.0050 $0.4140 $0.0350

$0.0052 $0.0062 $0.4097 $0.0340

est10X10X55 mm (Charpy 2mm V-Notch) Grain Size as per

TEST METHOD: A-370 ASTM E-112

TEST METHOD:

02 03 Avg(Joules) Temp °C

- - - - - - - - - - - - - - -

Relevant Report

GLECO/PT/J-825/5364 DATED 31.12.2024

s test carried out on each forging & found satisfactory. (4) Material is free from grease,
Sign & Stam of TPI Witness(if any)