VONETS - Wireless Module/Finished Product

Wireless module/WiFi product

VM300/VM5G/VBG1200/VAP11AC
Quick Setting Guide
VONETS - Wireless Module/Finished Product

Declaration
Copyright © 2023 Shenzhen HouTian Network Communication Technology Co.,Ltd

All rights reserved, with retained ownership Without Shenzhen HouTian Network
communication Technology Co.,Ltd written authorization, any company or personal can’t
copy, writer or translation part or all contents. Can’t do commodity distribution for any
commercial or profitable purposes by any ways(electricity, mechanical, photoprint, record or othe
r methods).

VONETS is the registered trademark of Shenzhen HouTian Network Communication

Technology Co.,Ltd. The other all trademarks or registered trademarks mentioned in this
documents are belong to the individual owners. The product specifications and information
technology mentioned in this manual are just for reference, if any updates, without other notice.
Except for special agreements, this manual is just for user guidance, any statements, information
and so on in this manual can’t constitute the warranty of any forms.

Product application and secondary development precautions

1. Problems related to wireless interference:
1.1 Use the ping command to test the wireless transmission performance. If it is found that the delay of
the ping packet response is extremely uneven, and there are many responses with a large delay, it can
basically be judged that the wireless has been strongly interfered;
1.2 The product antenna should be kept as far away as possible from sources of interference, such as
switching power supplies, antennas of other modules or wireless products, etc.;
1.3 If it is too close to the antenna of other wireless products, it will cause mutual interference,
resulting in an increase in the transmission bit error rate and a slower transmission rate. At this point, the
wireless signal must be properly attenuated. The methods of attenuating the signal include adding
obstacles, extending the distance, and adding a resistor in series between the antenna feed point and the
antenna, etc., to meet the actual application requirements;

2. Selecting a suitable power supply is the key to good and stable wireless transmission and stable
operation of the product. Improper power supply will cause damage to the product or poor wireless
performance. The selected power supply must meet the voltage range and input power requirements of
the power supply input, and the ripple must be less than the required maximum power supply ripple
(100mV);

Form 1
Transmission Distance Parameters Form

No-barrier point to
Transmission
Model point Transmission Band
Rate (Mbps)
Distance
VM300 80m--100m 300
VM5G/VBG1200/VAP11AC 600m--700m 300+900 5G
VONETS - Wireless Module/Finished Product

Form2

Power Supply Parameters List

Typical Power
Model Power Supply Voltage Input Power
Supply
VM300 DC5V--15V ≥5W 5V/1A
VM5G/VBG1200 DC5V--15V
≥10W 5V/2A
VAP11AC DC5V--24V
VONETS - Wireless Module/Finished Product

Contents
Chapter 1 Application Mode ................................................................... 1
1.1 Bridge + Repeater Mode .............................................................................................................. 1
1.2 Router Mode ................................................................................................................................ 2

Chapter 2 Bridge+Repeater Mode Configuration Instruction ................ 3

2.1.1 Device Connection .................................................................................................................... 3
2.2 Bridge+Repeater Application Configuration ................................................................................ 4
2.3 AP Application Configuration ....................................................................................................... 7

Chapter 3 Router Mode Configuration Instruction .................................. 9

3.1 Change device mode .................................................................................................................... 9
3.2 WAN port setting........................................................................................................................ 11
3.2.1 WAN/LAN exchange ............................................................................................................ 11
3.2.2 WAN Port connection method ......................................................................................... 12

3.2.3 WAN port wired connect network——DHCP .................................................................. 12

3.2.4 WAN port wired connect network——PPPoE ................................................................. 13

3.2.5 WAN port wireless connect network---- WiFi ................................................................ 13

3.3 Set WiFi hotspot parameters .................................................................................................. 15

Appendix Frequently Asked Questions ................................................. 17

VONETS - Wireless Module/Finished Product

Chapter 1 Application Mode

1.1 Bridge + Repeater Mode

There are three application modes for the bridge mode of VONETS module/WiFi product: WiFi
repeater, WiFi bridge and WiFi AP.

⚫ WiFi Repeater:
VONETS module/WiFi product as WiFi Repeater, it must be configured to source WiFi hostpot
parameters, can be used to extend the wireless signal coverage of existing APs or wifi router .

⚫ WiFi Bridge:
VONETS module/WiFi product as WiFi bridge, it must be configured to source WiFi hotspot
parameters, can be used for devices only with Ethernet ports to access wireless networks.

⚫ WiFi AP：
VONETS module/WiFi product as WiFi AP, it can achieve wireless access to wired LAN, no
configuration required, plug and play.

1
VONETS - Wireless Module/Finished Product

1.2 Router Mode

⚫ VONETS module/WiFi product as WiFi router
The Ethernet port of VM300 module/ VAP11AC finished product defaults to WAN port. The
Ethernet cable defaults to the LAN port. WAN and LAN ports are interchangeable.

The Ethernet cable of VM5G module/VBG1200 WiFi product defaults to LAN port, you must set
“WAN/LAN interchange” so that the Ethernet cable is WAN port to use the broadband
dialing function.

⚫ VONETS module/WiFi product is used as a wireless router. WAN port can be set to connect to
the WiFi hotspot for use as a secondary router.

2
VONETS - Wireless Module/Finished Product

Chapter 2 Bridge+Repeater Mode Configuration Instruction

2.1 Method 1: Log in to the device's Web configuration page to configure
2.1.1 Device Connection
Power on VONETS module/WiFi product by 5V/2A power supply, then connect to PC, there are two
connection ways as below:
A. Computer is wired connected to LAN port of VONETS module/WiFi product;

（Recommend Method）

B. The computer wirelessly connects to the WiFi signal of VONETS module/WiFi product, its
default hotspot parameters are as follows:
WiFi SSID: VONETS_****** (corresponding to VONETS device MAC address)
WiFi password: 12345678

3
VONETS - Wireless Module/Finished Product

(After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.)

2.2 Bridge+Repeater Application Configuration

The configuration steps of VONETS module/WiFi product for WiFi repeater and WiFi bridge are
basically the same, so this manual combines the configuration instructions of the two application
modes.

1. After computer is connected to VONETS module/WiFi product, open browser, input configured
page: http://vonets.cfg (or IP: 192.168.254.254), then press Enter;

2. Input User name and Password in login page (both are “admin”), click “Login” button to
enter configured page;

3. “Scan Hotspots”, choose the source hotspots, click “Next”;

4
VONETS - Wireless Module/Finished Product

4. Input “Source wireless hotspot password”, click “Apply”;

⚫ IP layer transparent transmission (factory default), transparent transmission of IP layer data,
can meet most of WiFi bridge applications;
⚫ MAC layer transparent transmission, transparent transmission of all data above the MAC
layer (link layer) and MAC layer, including IP layer data. MAC transparent transmission can
solve some special applications for MAC layer encryption, such as GoPro camera, Cisco AP,
Hikvision monitoring system, etc;
⚫ The option “The configuration parameters of WiFi repeater security is synchronized with
source hotspot” is default ticked, it means the SSID of VONETS repeater is associated with
the SSID of the source hotspot, and the WiFi password is the same as the password of the
source hotspot;
⚫ Disable hotspot, if you select “Disable hotspot” on the right side of the SSID, the device
will not transmit the corresponding hotspot and can only be used as a bridge application;
⚫ Advanced Setting,include Hot spot authentication match mode, WiFi Signal Motion
Detection and SSA Signal strength alarm threshold,these options here can be kept
unchanged, for instructions on this option, go to www.vonets.com and download the “V
Series WiFi Bridge Advanced Features Instruction”;

5
VONETS - Wireless Module/Finished Product

5. Click “Reboot”, VONETS module will connect to the configured WiFi hotspot automatically, if
connection is successful, the WiFi LED light will flash quickly;

6
VONETS - Wireless Module/Finished Product

Remark 1:

LED Light Form

Model Blue Light Green Light Yellow Light
WiFi Connection Ethernet Cable
VM300 /
Status Light Connection Status Light
WiFi Connection 5G WiFi Connection Ethernet Cable
VM5G/VBG1200/VAP11AC
Status Light Status Light Connection Status Light
① VONETS module/WiFi product is not connected to any hotspot, WiFi connection status light
will flash quickly;
② VONETS module/WiFi product is connected to hotspot successfully, WiFi connection status
light will quick flash;
③ VONETS module/WiFi product is connected to hotspot successfully, but hotspot signal
strength is less than 50% greater than 10%, WiFi status light will pause flash and flash;
④ VONETS module/WiFi product is connected to hotspot failed, WiFi connection status light will
flash slowly.

2.3 AP Application Configuration

VONETS module/WiFi product can be configured as an AP application. The wireless terminal device
can connect to VONETS module/finished product hotspot to connect to the network; however, it is
best to change its WiFi name and password for network security.

1. Log in to the configuration page http://vonets.cfg (or IP: 192.168.254.254) in your computer
browser, both user name and password are “admin”

2. Revise WiFi name: Jump to “WiFi Repeater”---- “Basic Settings”, enter new WiFi name in
“WiFi Repeater (SSID)”, click “Apply”;

7
VONETS - Wireless Module/Finished Product

3. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi password in
“Pass Phrase”, click “Apply”;

4. “WiFi Tx Power” of VONETS module/WiFi product can be changed, jump to “System

Settings”---- “Advance Settings”, choose suitable transmit power, then click “Apply”;

8
VONETS - Wireless Module/Finished Product

5. Reboot device, jump to “System Settings”---- “Reboot Device”, click “Reboot”, when it
is finished, all revised options will take effort.

Remark 2: When VONETS module/WiFi product connect to external network, its IP address will be
changed. At this time, when log in configured page, we suggest you enter configured domain name:
http://vonets.cfg. Or in Windows command window, enter the command: ping vonets.cfg, to get
the IP address of the device, then log in configuration page by this IP address.

Chapter 3 Router Mode Configuration Instruction

3.1 Change device mode

1. Power on VONETS module/WiFi product by 5V/2A power supply, then connect to PC, there are
two connection ways as below:
A. Computer is wired connected to LAN port of VONETS module/WiFi product;

9
VONETS - Wireless Module/Finished Product

（Recommend Method）

B. Computer wirelessly connects to the WiFi signal of VONETS module/WiFi product, its
default hotspot parameters are as follows:
WiFi SSID: VONETS_****** (corresponding to VONETS device MAC address)
WiFi password: 12345678

(After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.)

2. After computer is connected to VONETS module/WiFi product, open browser, input configured
page domain name: http://vonets.cfg (or IP: 192.168.254.254), then press Enter;

3. Enter User name and Password in login page (both are “admin”), click “Login” button to
enter configured page;

10
VONETS - Wireless Module/Finished Product

4. In “Operating Mode”, change Device mode to “Router” mode, click “Apply” button;

5. Reboot device: go to “System Settings”-- “Reboot device”, click “Reboot” button,

VONETS module/WiFi product will automatically switch to router mode.

3.2 WAN port setting

3.2.1 WAN/LAN exchange
In routing mode, the Ethernet port of VONETS module/WiFi product is divided into a WAN port and
a LAN port, and WAN/LAN can be interchanged.

The Ethernet port of VM300 module / VAP11AC finished product defaults to WAN port. The
Ethernet cable defaults to LAN port. If the interface mode is changed to “WAN/LAN exchange”,
the Ethernet cable will be WAN port and the Ethernet port will be LAN port.(This option can keep
unchanged);

The Ethernet cable of VM5G/VBG1200 WiFi product defaults to LAN port, the interface mode must
be changed to “WAN/LAN interchange” to make Ethernet cable to WAN port, click “Apply”,
then reboot VONETS module/WiFi product.

11
VONETS - Wireless Module/Finished Product

3.2.2 WAN Port connection method

By setting the WAN port of the router, you can change the network connection type according to
the actual needs of the individual, there are three types of WAN port connections commonly used
in the routing mode of the VONETS module/WiFi product: DHCP(Auto Config), PPPoE(ADSL) and
WiFi. DHCP and PPPoE are wired connections, and the WAN port needs to be connected to the
source network through a wired connection:
⚫ DHCP(Auto Config): WAN port connection type is selected as “DHCP(Auto Config)”, VONETS
module/WiFi product will automatically obtain IP address from source network;
⚫ PPPoE(ADSL): WAN port connection type is selected as “PPPoE”, that is, ADSL virtual dialing
mode requires ISP (Internet Service Provider) to provide Internet account and password.
⚫ WiFi: WAN port connection type is selected as “WiFi”, VONETS module/WiFi product uses a
built-in WiFi network card (used to connect to the source hotspot) as a WAN port, and all
Ethernet ports as LAN ports, while providing WiFi hotspot functions.

3.2.3 WAN port wired connect network——DHCP

The default WAN port connection mode of VONETS is DHCP. The WAN port can automatically
obtain an IP address after connecting with the source network.

12
VONETS - Wireless Module/Finished Product

3.2.4 WAN port wired connect network——PPPoE

In “WAN settings”, select “Basic settings”, change the connection type to “PPPoE (ADSL)”,
then enter the Internet account and password provided by the ISP (Internet Service Provider), click
the “Apply” button, and then reboot VONETS module/WiFi product, then can access to network.

3.2.5 WAN port wireless connect network---- WiFi

1. In “WAN Settings”, select “Basic Settings”, change Connection type to “WiFi”, then click
“Scan Hotspots” to enter the scanning hotspot list.

13
VONETS - Wireless Module/Finished Product

2. Choose the source hotspots, click “Next”;

3. Input “Source wireless hotspot password”, click “Apply”

⚫ The option “The configuration parameters of WiFi repeater security is synchronized with
source hotspot” is default ticked, it means the SSID of VONETS repeater is associated with
the SSID of the source hotspot, and the WiFi password is the same as the password of the
source hotspot;
⚫ Disable hotspot, if you select “Disable hotspot” on the right side of the SSID, the device
will not transmit the corresponding hotspot and can only be used as a bridge application;
⚫ Advanced Setting,include Hot spot authentication match mode, WiFi Signal Motion
Detection and SSA Signal strength alarm threshold,these options here can be kept
unchanged, for instructions on this option, go to www.vonets.com and download the “V
Series WiFi Bridge Advanced Features Instruction”;

14
VONETS - Wireless Module/Finished Product

4. Click “Reboot”, VONETS module/WiFi product will connect to the configured WiFi hotspot
automatically, if connection is successful, the WiFi LED light will flash quickly;(Please refer to
Remark 1 for the description of the LED light.)

Remark 3: After VONETS module/WiFi product sets the WAN port to access the WiFi hotspot in the
routing mode, its LAN port IP is still 192.168.254.254, and the terminal device also obtains the IP
address of the same network segment, can login configuration page by 192.168.254.254 or
http://vonets.cfg.

3.3 Set WiFi hotspot parameters

1. Revise WiFi name: Jump to “WiFi Repeater”---- “Basic Settings”, enter new WiFi name in
“WiFi Repeater (SSID)”, click “Apply”;

15
VONETS - Wireless Module/Finished Product

2. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi password in
“Pass Phrase”, click “Apply”;

3. Reboot device, jump to “System Settings”---- “Reboot Device”, click “Reboot”, when it
is finished, all revised options will take effort.

16
VONETS - Wireless Module/Finished Product

Appendix Frequently Asked Questions

1. How to restore the factory default parameters of the VONETS module/WiFi product?
Please refer to the information below to reset the factory default parameters of the VONETS
module/WiFi product：
VM300: http://www.vonets.com/serviceView.asp?D_ID=213
VM5G: http://www.vonets.com/serviceView.asp?D_ID=306
VBG1200: After the device is powered on for about 60 seconds, press and hold the Reset
button for 5 seconds and then release, the blue indicator light will flash a few times, and then
the device will automatically restore the factory default parameters (the restoring process
takes about 80 seconds). During operation, the product cannot be powered down, otherwise it
may cause damage to the product.

2. Does VONETS module/WiFi product support firmware upgrade, how to upgrade?

VONETS module/WiFi product t supports firmware upgrade, and support online upgrade, please
visit website: www.vonets.com to refer to the related documents.

3. The device WiFi hot spot can be found, but the smart phone or PC can’t connect to this device
hotspot?
⚫ Reason 1. Due to some unexpected operation or power down, caused the destroy of
device parameters. At this time, just need to reset the device to factory default
parameters;
⚫ Reason 2. The device WiFi doesn’t work at the best channel, make the performance
worse. At this time, you can try to change the source WiFi hot spot and this device WiFi
channel to make the performance better;
⚫ Reason 3. The smart phone or PC haven’t been configured the correct WiFi password.

4. The device has been configured the source WiFi hot spot parameters, the smart phone or PC
has connected to the device WiFi hot spot, but still doesn’t get internet?
⚫ First, check the status light to know the current state of the device, then according to the
state of the device to analyze the fault reasons;
⚫ Reason 1. The distance between the device and source WiFi hot spot is too long, cause the
communication performance degradation, finally effect the user’s access to the Internet.
At this time, just need shorten the distance between the device and source WiFi hot spot
to solve this problem;
⚫ Reason 2. Due to some unexpected operation or power down, caused the destroy of
device parameters. At this time, just need to reset the device to factory default
parameters;

17
VONETS - Wireless Module/Finished Product

⚫ Reason 3. The device WiFi doesn’t work at the best channel, make the performance worse.
At this time, you can try to change the source WiFi hot spot WiFi channel to make it the
same as the default channel of the device, the reboot the device, the device will
automatically exchange to the same channel as the source WiFi hotspot, to make the
performance better;
⚫ Reason 4. There are several WiFi hot spot around the device, WiFi channel mutual
interference, make the performance worse. At this time, you can try to change
the source WiFi hot spot and this device WiFi channel to make the performance
better;
⚫ Reason 5. The configured source WiFi hot spot parameters are not correct. At this time,
just need to configure the correct parameters then reboot the device;

5. The smart phone or PC has been connected the device by WiFi or Ethernet cable, but user
can’t log in the device WEB page, or after log in the WEB it shows error?
⚫ Reason 1. The users don’t use the browser recommended by VONETS(IE,Google Chrome,
Safari, the mobile phone browser);
⚫ Reason 2. The smart phone or PC installed the firewall, the security level is set too high,
caused the above problem. At this time, only need to close the firewall;
⚫ Reason 3. The security level of browser is too high, it will also cause the above problem. At
this time, just need to reduce the browser’s security level, then log in again;
⚫ Reason 4. The IP address of the device input error. For the new device from the factory,
user only need input the correct IP address according to the instruction guide; for the
device that has connected the source hot spot, user only operate according to <Remark 2>.

18
VONETS - Wireless Module/Finished Product

FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Operation of this device in the band 5150-5250 MHz is restricted to indoor use
only

19