Scribd
Upload
115 views12 pages

Log in To SMU Controller and Configure High Temperature Start DG Guide

How to make log in

Uploaded by

Zeferino Joelson
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
115 views12 pages

Log in To SMU Controller and Configure High Temperature Start DG Guide

How to make log in

Uploaded by

Zeferino Joelson
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 12

Issue 03

Date 2020-05-30

HUAWEI TECHNOLOGIES CO., LTD.


Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.

Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.


Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

Huawei Proprietary and Confidential


Issue 01 (2014-07-016) i
Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide Contents

Contents

1 Log in Preparation ................................................................................................................. 3


1.1 Prepare Pc and Power System .............................................................................................................................................. 3
1.2 (Set the DG control by High temp using webUI) ............................................................................................................... 3

2 Performing the Configuration .............................................................................................. 9

Issue 01 (2014-07-016) Huawei Proprietary and Confidential ii


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 1 Log in Preparation

1 Log in Preparation

1.1 Prepare Pc and Power System

1.2 (Set the DG control by High temp using webUI)


The cable is the normal network cable

Figure 2-2 FE port pin definitions

-For In band sites: The default IP address of SMU02 is 192.168.0.10. The default URL
which can be used to access SMU02 controller is https://192.168.0.10/login.asp.

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 3


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 1 Log in Preparation

NOTE: For OUT BAND sites please first check the IP in SMU.

Check the IP in the controller:


-In Out band sites: Check the IP address of SMU on the site on the LCD screen base on
the IP address allocated by customers. The LCD default password is 000001.
LCD Network Parameters Menu

After the check, Set the IP address, subnet mask and default gateway of your
computer/laptop, it should be in the same subnet of SMU02, but with a slightly different IP
address.
As below steps for reference:

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 4


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 1 Log in Preparation

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 5


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 1 Log in Preparation

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 6


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 1 Log in Preparation

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 7


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 1 Log in Preparation

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 8


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 2 Performing the Configuration

2 Performing the Configuration

Step 1 Login Web UI


Step 2 Connect network cable from controller SMU02 to computer.
Step 3 Enter the https://<input site IP after checking the controller>
Open the Internet Explorer/Chrome and type the SMU IP address in the address bar, and then
press enter.
SMU defaults URL for WEBUI is https://192.168.0.10/login.asp. <For In band sites>.
Enter user name: The preset user name is admin and password is Changeme
Figure 3-3 Enter SMU IP Schematic for In-band (https://192.168.0.10/). For Out-band
https://<input site IP after checking the controller for site IP>

Figure 3-4 Login UI

Option 1 Configure high temperature start generator by Web UI

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 9


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 2 Performing the Configuration

5. Select Enable and set the High Temperature Start and High Temperature Stop.
6. Select Enable and set the Low Temperature Start and Low Temperature Stop.

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 10


Copyright © Huawei Technologies Co., Ltd.
SMU V200R002C00 Upgrade Guide 2 Performing the Configuration

Option 2. Configure high temperature start generator on NetEco


Login NetEco as Admin user:

Option 3. Configure high temperature start generator on LUI


Log in controller as below, default password is 000001

Issue 01 (2014-07-016) Huawei Proprietary and Confidential 11


Copyright © Huawei Technologies Co., Ltd.

You might also like