Scribd
Upload
12 views

Error_codes_3

Uploaded by

Dinesh Babu Shrestha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
12 views

Error_codes_3

Uploaded by

Dinesh Babu Shrestha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 1

E100 The BD signal cannot be detected within a specific time.

Related laser

E101 The AF motor of the laser unit is faulty.

E102 The light intensity of the laser does not reach a specific level.

E110 The polygonal scanner motor does not reach a specific speed within a specific time. Related laser
scanner
E111 The polygonal cooling fan does not rotate properly.

E120 The temperature of the laser does not reach a specific value. Related laser
temperature control
E121 The stoppage of the laser cooling fan is detected.

The movable guide motor is turned ON, and a specific position cannot be detected within a specific Related BJ
E140 time.
1.The capping motor is turned ON, and a specific position cannot be detected within a specific time.
2.A specific position of the cam sensor for the recovery system cannot be detected within a specific
E141 time.

The pressure position switching motor is turned ON, and a specific position cannot be detected
E142 within a specific time.
The intake switching motor is turned ON, and a specific position cannot be detected within a
E143 specific time.
A detection signal is not returned to the ink pump monitor after the ink pump is activated: DCC ->
E144 BHD -> pump drive signal
No signal is generated from the position sensor within a specific time after a drive signal of the
E145 cutter motor is generated.
1.The waste ink full sensor is turned ON.
E146 2.The intake counter for waste ink exceeds a specific value.

E150 Neither thermistor nor trimmer resistance is connected to the head. (The head is not connected.) Related BJ head

E151 The thermistor of the head is open-circuited.

E152 The thermistor of the head is short-circuited.

E153 The trimmer resistance of the head is open-circuited.

E154 The trimmer resistance of the head is short-circuited.

E155 The trimmer resistance of the head is out of specifications.

When a specific voltage is applied to the head, the voltage of the head is not changed within a
E156 specific time.

E157 The voltage of the head is out of the specifications.

E160 The temperature of the head does not reach a specific temperature within a specific time. Related BJ head
temperature control
E161 The temperature of the head exceeds a specific temperature.

When the pulse motor for the head scan is driven, it cannot be detected by a sensor within a Related BJ head
E170 specific time. scanner

E171 The motor is not connected to the pulse motor driver PCB for the head scan.

E172 The gate array employed to drive the pulse motor for head scan is faulty.

E180 The motor is not connected to the vertical scanning pulse motor driver PCB. Related BJ paper
feed
E181 The gate array employed to drive the vertical scanning pulse motor is faulty.

After the vertical scanning motor is driven, the phase sensor cannot be detected within a specific
E182 time.
After the registration roller cam clutch 2 is turned ON, a given paper size cannot be detected within
E183 a specific time.

E190 RAM directly connected to CPU is faulty. Related CPU Failures in RAM of the laser
(printer unit) controller are indicated with
E1 91 An error occurs in the communication with the microcomputer (D/A converter) for high voltage use. detail codes.
E192 An error occurs in the communication with A/D converter.

E193 The gate array is faulty.

The auto registration is faulty.


E1 94 Data from the # pattern reading CCD is invalid.

E195 ROM failure -> No. of times data is written on EEPROM reaches the upper

EEPROM failure: EEPROM read and write error (except software counter),
E196 li it an error in EEPROM areas on DIMM.
An error occurs in the communication within the printer:
•Errors continuously occur in the communication within the printer.
E197 •Interruption during receiving is not made within a specific time.

E198 An error occurs in IC on the DC controller.

You might also like