Scribd
Upload
62 views3 pages

001-088 Engine Base Timing

Uploaded by

Hussain Ahmed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
62 views3 pages

001-088 Engine Base Timing

Uploaded by

Hussain Ahmed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

25/03/2024, 10:24 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

(/qs3/pubsys2/xml/en/manual/4388731/4388731-titlepage.html)

Trainings

Select Service Tools


Recommended Cummins® Service Tools
Crankshaft locking pin, Part Number 5298581
Timing pin, Part Number 4919342
Additional Service Items
No additional service items required.

Test
This procedure describes the basic orientation of the Rear
Gear Train (RGT) and engine timing.

The illustration shows the assembly.

1. Camshaft gear
2. Fuel pump gear
3. Crankshaft gear
4. Crankshaft idler gear

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 1/3
25/03/2024, 10:24 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

5. Camshaft idler gear

 CAUTION 
The crankshaft timing pin and the camshaft timing pin
must be installed before any gears are removed and must
remain in place until all gears are fully installed and
tightened. Failure to install the timing pins can lead to
improper timing of the engine, resulting in severe engine
damage or engine failure.

Rotate the crankshaft clockwise until the hole in the


crankshaft pulley is aligned with the crankshaft pin boss hole in
the lubricating oil pump.

Insert the crankshaft locking pin, Part Number 5298581,


included in kit number 5298582, into the timing pin boss hole.

The crankshaft will be locked in place when the pin is properly


seated.

Remove the rocker lever cover and gasket. Refer to


Procedure 003-011 in Section 3.
(/qs3/pubsys2/xml/en/procedures/417/417-003-011-tr.html)
Remove the rocker lever assemblies. Refer to Procedure
003-009 in Section 3.
(/qs3/pubsys2/xml/en/procedures/417/417-003-009.html)

Insert timing pin, Part Number 4919342, to lock the


camshaft. The camshaft will be locked in place when the pin is
properly in place.

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 2/3
25/03/2024, 10:24 QuickServe Online | (4388731) QSG12 CM2880 G112 Service Manual

Note : When the crankshaft and the camshaft are both


pinned, the engine is timed. If the engine is not timed
properly, the camshaft must be turned to the proper
position so it can be pinned.

Note : To turn the camshaft, the crankshaft idler gear


must be removed. Refer to Procedure 001-118 in
Section 1. (/qs3/pubsys2/xml/en/procedures/417/417-
001-118.html)

Finishing Steps
Remove crankshaft and camshaft pins.
Install the rocker lever cover and gasket. Refer to Procedure 003-011 in Section 3.
(/qs3/pubsys2/xml/en/procedures/417/417-003-011-tr.html)
Operate the engine to normal operating temperature and check for leaks and proper
operation.

Last Modified: 12-Sep-2017

https://quickserve.cummins.com/qs3/portal/service/manual/en/4388731/ 3/3

You might also like