Scribd
Upload
94 views4 pages

Psii (Ass 1)

Uploaded by

guddeeeyasu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
94 views4 pages

Psii (Ass 1)

Uploaded by

guddeeeyasu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Assignment 1#10%

1. Assume a 0.8+j0.4 per unit load at bus 2 is being supplied by a generator at bus 1 through
a transmission line with series impedance of 0.05 + j0.1 per unit. Assuming bus 1 is the
swing bus with a fixed per unit voltage of 1.0+j0.0, use the Gauss-Seidel method to
calculate the voltage at bus 2 after three iterations.
2. For the three bus system whose Ybus is given below, calculate the second iteration value
of V3 using the Gauss-Seidel method. Assume bus 1 as the slack with V1=1.0+j0.0pu, and
buses 2 and 3 are load buses with a per unit load of S2=1+ j0.5 and S3=1.5 + j0.75. Use
voltage guesses of 1.0+j0.0pu at both buses 2 and 3. The bus admittance matrix for a
three-bus system is

3. A generator bus (with a 1.0 per unit voltage) supplies a 150 MW, 50 Mvar load through a
lossless transmission line with per unit (100 MVA base) impedance of j0.1 and no line
charging. Starting with an initial voltage guess of 1.0+j0.0pu, iterate until converged
using the Newton–Raphson power flow method. For convergence criteria use a maximum
power flow mismatch of 0.1 MVA.
4. For a three bus power system assume bus 1 is the swing with a per unit voltage of
1.0+j0.0, bus 2 is a PQ bus with a per unit load of 2.0+ j0.5, and bus 3 is a PV bus with
1.0 per unit generation and a 1.0 voltage set point. The per unit line impedances are j0.1
between buses 1 and 2, j0.4 between buses 1 and 3, and j0.2 between buses 2 and 3.
Starting with an initial voltage guess of 1.0+j0.0, determine the first iteration phasor
voltages Newton–Raphson approach at buses 2 and 3.
5. With the complex powers on load buses 2, 3, and 4 as shown in Figure-1, determine the
value for V2, V3 and V4 that is produced by the first and second iterations of the Gauss–
Seidel procedure. Choose the initial guess V2 (0) =V3 (0) =V4 (0) =1+j0.0 per unit.
Figure-1: four bus power system

The bus admittance matrix for the power system shown in Figure-1 is given by

6. With load and line data of a 3 bus power system given in table-1 and 2,
A. Determine the phasor value of voltage at bus 2 and 3 using GS method at the end of
iteration two
B. Determine the phasor value of voltage at bus 2 and 3 using NR method at the end of
iteration two
C. Determine the slack bus power in part (a) and (b)
D. Determine line flows and line losses (a) and (b)
Table-1: load and generation data
Table-2: line impedance data

7. Figure 2 shows the single line diagram of a 3-bus power system with bus-3 is a P|V| bus, bus-1
slack bus and bus-2 load bus. With initial and flat starting voltage of V2(0)=1.0+j0.0pu,
V1=1.025+j0.0pu(slack bus), |V3|=1.0pu and V3(0)= 1.0+j0.0pu.
A. Determine the phasor value of voltage using GS method at the end of iteration two
B. Determine the phasor value of voltage using NR method at the end of iteration two
C. Determine the phasor value of voltage using Fast decoupled-NR method at the end
of iteration two
D. Determine the slack bus power in part (a), (b) and (c)
E. Determine line flows and line losses (a), (b) and (c)

Figure-2: three-bus power system

8. For a three bus power system as shown in Figure-3, assume bus 1 is the swing with a per
unit voltage of 1.0+j0.0 and bus 2 and 3 are load bus. With initial and flat starting voltage of
V1 =1+j0.0pu and V2 (0) =V3 (0) =1+j0.0pu,
A. Determine the voltage magnitude and phase angle of bus 2 and 3 using NR-method
at the end of iteration two
B. Determine the voltage magnitude and phase angle of bus 2 and 3 using decoupled
NR-method at the end of iteration two
C. Determine the voltage magnitude and phase angle of bus 2 and 3 using fast
decoupled NR-method at the end of iteration two
D. Determine the slack bus power in part (a), (b) and (c)
E. Determine line flows and line losses (a), (b) and (c)

You might also like