Scribd
Upload
12 views2 pages

Spherical Tank Volume Calculation

Spherical tank volume calculator

Uploaded by

Eng. Abobakr Alsufyani Sr.Mechnical engineer-
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
12 views2 pages

Spherical Tank Volume Calculation

Spherical tank volume calculator

Uploaded by

Eng. Abobakr Alsufyani Sr.Mechnical engineer-
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Fuel Level in a Spherical Tank 45

Spherical tanks are found in many


different situations, from the storage of
cryogenic liquids, to fuel tanks. Under
the influence of gravity, or acceleration,
the liquid will settle in a way such that it
fills the interior of the tank up to a height,
h. We would like to know how full the
tank is by measuring h and relating it to
the remaining volume of the liquid. A
sensor can then be designed to measure
where the surface of the liquid is, and
from this derive h.

Problem 1 - Slice the fluid into a series of vertically stacked disks with a radius r(h) and
a thickness dh. What is the general formula for the radius of each disk?

Problem 2 - Set up the integral for the volume of the fluid and solve the integral.

Problem 3 - Assume that fluid is being withdrawn from the tank at a fixed rate
dV/dt = -F. What is the equation for the change in the height of the fluid volume with
respect to time? A) Solve for the limits h<<R and h>>R. B) Solve graphically for R=1
3
meter, F=100 cm /min. (Hint: select values for h and solve for t).

Space http://
Math spacemath.gsfc.nasa.gov
Answer Key 45
2 2 2 2 2
Problem 1 - r(h) = R - (R-h) so r(h) = 2Rh - h

2 2 3
Problem 2 - The integrand will be  (2Rh - h ) dh and the solution is Rh -1/3h

Problem 3 -

dV dh dh dV dh
2 2
---- = 2  R h ---- - h ---- so ----- = (2  R h -  h ) ---- = -F
dt dt dt dt dt

Then

dh -F
=
2
dt (2  R h -  h )
2
The integrands become: (2  R h -  h ) d h = - F d t . This can be integrated from t=0
2 3
to t = T to obtain  R h - 1/3  h = - F T and simplified to get
3 2
h - 3 R h - (3 F T)/ = 0
3
We would normally like to invert this equation to get h(T), but cubic equations of the form x -
2
 x +  = 0 cannot be solved analytically. We can solve it for two limiting cases. Case 1 for a
1/2
tank nearly empty where h << R. This yields h(T) = (F T/R) Case 2 is for a tank nearly full
3
so that h >> R, and we get h = 3 F T/ and h(T) = (3 F T/ 1/3. The full solution for h(T)
can be solved graphically. Since R is a constant, we can select a new variable U = h/R and re-
write the equation in terms of the magnitude of h relative to the radius of the tank.
3 2 3
U - 3 U = (3 F T)/ R and plot this for selected combinations of (U,T) where time, T, is
3
the dependent variable. The solution below is for F = 100 cm /minute, R = 1 meter, with the
intervals in h spaced 10 cm. The plot was generated using an Excel spreadsheet.

250

200

150
Height

100

50

0 200 400 600 800 1000

Time (minutes)

Space http://
Math spacemath.gsfc.nasa.gov

You might also like