Scribd
Upload
3 views

Arduino program

Uploaded by

moooo yii trrhj
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
3 views

Arduino program

Uploaded by

moooo yii trrhj
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 8

Arduino editor form

Copy the following


code into the Arduino
editor
/**
PROGRAMMING AN ATMEL AT89S51/52 USING
ARDUINO
RELEASED AS IS WITHOUT WARRANTY
I AM NOT LIABLE FOR ANY DAMAGE DONE TO YOUR
HARDWARE
THIS PROJECT IS FOR EDUCATIONAL PURPOSES ONLY
Credits to NICK PABLO for the Arduino Sketch
TIKTAK (C) 2014 **/

#define dummyData 0xAA


#define RDY 75
#define NRDY 76

const int _MISO = 4;


const int _MOSI = 5;
const int _CLK = 3;
const int RST = 2;

/* Variable definition block */

byte data;
byte AL,AH; // 16-bit address
byte lockByte; // embed lock bits here
byte SigH,SigL; // Signature Bytes

2
void setup()
{ pinMode(_MISO, INPUT);
pinMode(_MOSI, OUTPUT);
pinMode(_CLK, OUTPUT);
pinMode(RST, OUTPUT);
Serial.begin(115200); // depends on the setting of
the host PC
}

void loop()
{ while (!Serial.available()); // wait for character
if (Serial.available() > 0)
switch (Serial.read())
{
case 'p': Serial.write(progEnable());
break;
case 'r': readProgmem();
Serial.write(data);
break;
case 'a': while(!Serial.available());
AL = Serial.read();
break;
case 'A': while(!Serial.available());
AH = Serial.read();
break;
case 'd': while(!Serial.available());
data = Serial.read();
break;
case 'S': AH = 0;
AL = 0;
SigH = readSign();
Serial.write(SigH);
break;
case 's': AH = 2;

3
AL = 0;
SigL = readSign();
Serial.write(SigL);
AH = 1;
AL = 0;
SigL = readSign();
Serial.write(SigL);
break; // read SigL
case 'o': digitalWrite(RST,1);break;
case 'c': digitalWrite(RST,0);break;
case 'e': eraseChip();
Serial.write(RDY);
break;
case 'j': break;
case 'w': writeProgmem();
break; }

unsigned char SendSPI(unsigned char data)


{
uint8_t retval = 0;
uint8_t intData = data;
int t;

for (int ctr = 0; ctr < 7; ctr++)


{
if (intData & 0x80) digitalWrite(_MOSI,1);
else digitalWrite(_MOSI,0);

digitalWrite(_CLK,1);
delayMicroseconds(1);

t = digitalRead(_MISO);
digitalWrite(_CLK,0);
4
if (t) retval |= 1; else retval &= 0xFE;
retval<<=1;
intData<<= 1;
delayMicroseconds(1);
}
if (intData & 0x80) digitalWrite(_MOSI,1);
else digitalWrite(_MOSI,0);

digitalWrite(_CLK,1);
delayMicroseconds(1);

t = digitalRead(_MISO);
digitalWrite(_CLK,0);

if (t) retval |= 1;
else retval &= 0xFE;
return retval; }

byte progEnable()
{ SendSPI(0xAC);
SendSPI(0x53);
SendSPI(dummyData);

return SendSPI(dummyData); }

void eraseChip()
{ SendSPI(0xAC);
SendSPI(0x9F);
SendSPI(dummyData);
SendSPI(dummyData);

delay(520); }

5
void readProgmem()
{ SendSPI(0x20);
SendSPI(AH);
SendSPI(AL);
data = SendSPI(dummyData); }

void writeProgmem()
{ SendSPI(0x40);
SendSPI(AH);
SendSPI(AL);
SendSPI(data); }

void writeLockBits()
{ SendSPI(0xAC);
SendSPI(lockByte);
SendSPI(dummyData);
SendSPI(dummyData); }

void readLockBits()
{ SendSPI(0x24);
SendSPI(dummyData);
SendSPI(dummyData);
lockByte = SendSPI(dummyData); }

byte readSign()
{ SendSPI(0x28);
SendSPI(AH);
SendSPI(AL);
return SendSPI(dummyData); }

6
Use the following
software to burn
AT89Sxx via the
Arduino kit

7
The form of 8051 SPI programmer software

You might also like