Parts and Accessories

Installation Instructions

INFO
1 4

2 5
3 6 TONE SELECT
FM AM

MODE MENU

039 0524 B

Retrofit Kit On-board Monitor and Navigation System

BMW 5 Series Saloon (E 39)

These installation instructions are only valid for cars with a production date prior to 9/00 with SA555
high on-board computer.
Technical and electrical knowledge required
The installation time is approx. 7 hours, which may vary depending on the condition of the car and the
equipment in it.
Retrofit kit No. 65 90 0 025 171
65 90 0 027 764

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date:
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
Contents

Section Page

Important information on the installation of the on-board monitor and navigation system
1. Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. Installation and cabling diagram for the on-board monitor wiring harness. . . . . . . . . . . . . . . . . . . . . 12
5. Installation and cabling diagram of the supplementary wiring harness
for the navigation system in cars with a production date prior to 9/98 . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Installation and cabling diagram of the supplementary wiring harness
for the navigation system in cars with a production date after 9/98 . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7. To install the additional tacho A signal cable in cars with a production date after 9/99,
without tacho A signal on the radio connection plug X18126 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8. To install the on-board monitor wiring harness, on-board monitor and on-board monitor radio . 16
9. To install the supplementary wiring harness for navigation systems
in cars with a production date prior to 9/98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10. To choose installation of the supplementary wiring harness for navigation systems
in cars with a production date after 9/98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
11. To install the supplementary wiring harness for navigation systems
in cars with a production date after 9/98 (PIN 18 and PIN 35 on the connection plug of the ABS
hydraulic unit not occupied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
12. To install the supplementary wiring harness for navigation systems
in cars with a production date after 9/98 (PIN 18 and PIN 35 on the connection plug of the ABS
hydraulic unit occupied). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
13. To install the supplementary wiring harness for navigation systems
in cars with a production date after 9/98
(PIN 18 occupied and PIN 35 not occupied on the connection plug of the ABS hydraulic unit). . 28
14. To install the supplementary wiring harness for navigation systems
in cars with a production date after 9/98
(PIN 18 not occupied and PIN 35 occupied on the connection plug of the ABS hydraulic unit). . 31
15. To install the navigation system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
16. Coding and concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
17. Connection description for TV function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
18. Circuit diagram for the on-board monitor wiring harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
19. Circuit diagram for the navigation system wiring harness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
20. Circuit diagram for supplementary wiring harness for navigation systems
in cars with a production date prior to 9/98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
21. Circuit diagram for supplementary wiring harness for navigation systems
in cars with a production date after 9/98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/2
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
Important information on the installation of the on-board monitor and navigation system

Only for use in the BMW dealer organisation.

The on-board monitor and navigation system may only be installed by a specialist workshop that has the
required special tools and manuals (servicing, repair, diagnostics, etc.).

Ensure that the cables/lines are not kinked or damaged as you install them in the car.

Additionally installed cables/leads should where necessary be fastened with cable ties.

Item numbers refer only to the overview drawings and to the texts next to the appropriate figure.

All the work is shown for a LHD car, the same procedure should be used as appropriate in RHD
cars.
Electrical knowledge is required.

The on-board monitor radio / CD changer control cable is not supplied with the installation kit and must
be ordered separately for cars with a CD changer without a DSP amplifier using the electronic parts
catalogue (EPC).
The trim at the rear left of the boot in front of the navigation computer does not form part of the
installation kit and must be ordered separately depending on the equipment in the car using the
electronic parts catalogue (EPC)."

Subject to technical modifications

Required tools and equipment

MoDIC III or DIS Hot air blower
1/4 inch socket set Set of Torx sockets
Set of Philips screwdrivers Set of flat screwdrivers
Cable lamp Universal knife
Angle cutter Set of short Philips screwdrivers
Silicone

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/3
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
1. Preparations

TIS instruction No.

Print out error memory -
Disconnect the battery 12 00 ...
Remove the central instrument panel décor trim on the left-hand side 51 45 030
Remove the instrument panel décor trim on the right-hand side 51 45 030
Remove the radio (no longer required) 65 11 030
Remove the control (no longer required) 65 12 040
Undo the bottom part of the instrument panel trim (according to TIS) -
Remove the radio module holder, it is replaced by the on-board monitor 51 16 202
module holder (installation is described in TIS)
Remove the front left centre console 51 16 239
Undo the centre console at the front left at the bottom 51 16 239
Remove the left front seat 52 17 000
Remove the rear seat bench 52 24 005
Remove the rear seat backrest 52 24 015
Remove the door sill strip at the front and rear left 51 47 000/51 47 030
Remove the bottom section of the B pillar trim on the left -
Raise the carpet at the left -
Remove the C pillar trim on both sides 51 43 251
Remove the rear window shelf 51 46 000
Remove the left speaker under the rear window shelf -
Remove the boot floor 51 47 101
Remove the rear left boot trim 51 47 151
(it is replaced by a new trim)
Remove the left boot trim -
Remove the rear right boot trim 51 47 172
Remove the closing panel trim 51 46 050
Remove the door sill strip at the front and rear right 51 47 000/51 47 030
Remove the bottom section of the B pillar trim on the right -
Remove the A pillar trim at the bottom right -
Remove the glove compartment 51 16 360
Fold up the carpet on the right -
Remove the CD changer (if fitted) 65 11 070
Remove the holder for the CD changer (if fitted) -
Remove the video module bracket (if fitted) -
Remove the DSP amplifier holder (if fitted) 65 11 070
Remove the holder for the DSP amplifier (if fitted) 65 11 070

Also in RHD cars

0

Remove the footwell trim below the steering column -

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/4
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
1. Preparations

In addition, in cars with a production date after 9/99 without a tacho A signal on the radio
connection plug X18126
0

Remove the instrument cluster trim 62 21 000

Remove the instrument cluster 62 21 000

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/5
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
2. Parts list

2 3 4 5

7 8 9 10 11

12 13 14 15
INFO
1 4

2 5
3 6 TONE SELECT
FM AM

MODE MENU

16 17 18 19

039 0525 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/6
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
2. Parts list

20 21 22 23

24 25 26 27 28 29 30

31 32 33 34 35 36

37 38 39 40 41 42 43

039 0526 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/7
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
2. Parts list

1 On-board monitor wiring harness

2 Navigation system wiring harness
3 Supplementary wiring harness for navigation systems in cars with a production date prior to 9/98
4 Supplementary wiring harness for navigation systems in cars with a production date after 9/98
5 Aerial extension for the GPS aerial
6 GPS aerial
7 Additional tacho A signal cable
8 Shrink hose (included in additional cable pack containing additional tacho A signal cable)
9 2-way insulation-piercing connector (included in additional cable pack containing additional tacho A
signal cable)
10 Securing clip
11 Holder for the GPS aerial
12 On-board monitor, complete
13 On-board monitor holding pin (to support the on-board monitor)
14 On-board monitor module holder
15 Fillister head Philips screw M3x8 (4x)
16 Trim for on-board monitor
17 On-board monitor radio
18 Holder for DSP amplifier
19 Base holder
20 Front video module bracket
21 Holder for on-board monitor radio and CD changer
22 Navigation computer
23 Navigation computer holder
24 Hexagonal nut with washer M5
25 Hexagonal screw with washer M5x14 (8x)
26 Speed nut M5 (7x)
27 Hexagonal self-tapping screw with washer 4.8x16 (3x)
28 Plastic expanding nut 4.8 (3x)
29 Plastic cap nut (3x)
30 Rubber grommet (2x)
31 Fastening grommet (GPS aerial holder) (2x)
32 Expanding rivet for securing the GPS aerial (2x)
33 Removal bar (2x)
34 Cable tie (20x)
35 Cable holder (2x)
36 Sealing strip
37 Shrink hose (included in pack for the supplementary navigation system wiring harness) (2x)
38 Protective strip (2x)
39 Butt-joint connector (7x) * (for cable cross-section 0.2 – 0.5 mm2)
40 Butt-joint connector (10x) * (for cable cross-section 0.75 – 1.0 mm2)
41 Butt-joint connector (4x) * (for cable cross-section 1.5 – 2.5 mm2)
42 Hose (20x) *
43 Fabric tape *

Retrofitparts
The marked
kit No. 65 with an asterisk
90 0 025 171 (others(*)
see are
cover not
sheet)required. Issue date: EN/8
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
3. Connection diagram

A7 A8
A6 A9

A13
A5 A10
A14
A A4 A11
A3
A12
A15
A2
A1 B
A16

B4
B5
B3
B6
C C3
B2 C5
B1 C1

C6
C2 C4
D3 D4
D

D1 D5

E D6
D2
E1 E2

F
F2

F1

F3
039 0527 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/9
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
3. Connection diagram

Cable
Item Description Connection location in the car
colour
A On-board monitor wiring harness - -
A1 Blue 12-pin socket casing - To blue 12-pin plug casing on on-board monitor (12)
A2 White 12-pin socket casing - To white 12-pin plug casing on on-board monitor (12)
A3 Black 17-pin plug casing - To radio connection plug X18126
A4 Coaxial plug casing black To be laid to the installation site of the left TV amplifier in the left-hand
C pillar and tied back
A5 Coaxial plug casing black To be laid to the installation site of the right TV amplifier in the right-
hand C pillar and tied back
A6 Angled coaxial socket casing black To be tied back on the on-board monitor wiring harness A with a cable
tie
A7 Angled coaxial socket casing black To be tied back on the on-board monitor wiring harness A with a cable
tie
A8 Black coaxial socket casing (aerial connector) black To the coaxial plug casing on the on-board monitor (17) (aerial
connector)
A9 Angled coaxial socket casing black To the coaxial plug casing on the on-board monitor (17)
A10 Cable eyelet, 6 mm in diameter brown To earth post connection X13016 on the left-hand C pillar
A11 Coaxial socket casing black To the coaxial plug casing on the aerial diversity
A12 Coaxial plug casing black To the coaxial socket casing on the aerial diversity
A13 Black 17-pin socket casing - To the on-board monitor radio (17)
A14 10-pin socket casing - To be clipped into the black 17-pin socket casing A13 of the on-board
monitor wiring harness A and connected to the on-board monitor radio
(17) using the black 17-pin socket casing A13
A15 White 6-pin plug casing - To branch B1, white 6-pin socket casing, of the navigation system
wiring harness B
A16 Blue 18-pin socket casing - To blue 18-pin plug casing on navigation computer (22)

B Navigation system wiring harness - -

B1 White 6-pin socket casing - To branch A15, white 6-pin plug casing, of the on-board monitor wiring
harness A
B2 Black 6-pin socket casing - In cars with a production date prior to 9/98
To branch C1, black 6-pin plug casing, of the supplementary wiring
harness for the navigation system C
-------------------------------------------------------------------------------
In cars with a production date after 9/98
To branch D1, black 6-pin plug casing, of the supplementary wiring
harness for the navigation system D
B3 White 18-pin socket casing - To be tied back on the navigation system wiring harness B with a cable
tie
B4 Black 6-pin plug casing - To be tied back on the navigation system wiring harness B with a cable
tie
B5 Blue 18-pin socket casing - To be tied back on the navigation system wiring harness B with a cable
tie
B6 Bordeaux 18-pin socket casing - To Bordeaux 18-pin plug casing on navigation computer (22)

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/10
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
3. Connection diagram

Cable
Item Description Connection location in the car
colour
C Supplementary wiring harness for - -
navigation systems in cars with a
production date prior to 9/98
C1 Black 6-pin plug casing - To branch B2, black 6-pin socket casing, of the navigation system
wiring harness B
C2 Cable eyelet, 6 mm in diameter brown To earth post connection X10305 below the left tail light
C3 Cable eyelet, 6 mm in diameter brown To earth post connection X10012 in the front area of the right-hand door
sill
C4 1-pin blade terminal contact white/yellow To light module X10117 in black 54-pin socket casing, PIN 38

C5 1-pin blade terminal contact black To connection plug X1171 of the ABS control unit, PIN 9, tie back
excess length in LHD cars
-------------------------------------------------------------------------------
In automatic cars with M62 B44 engine and DSC, from
production date 9/97 to production date 9/98
To connection plug X1171 of the ABS control unit
in PIN 72, tie back excess length in LHD cars
C6 1-pin blade terminal contact yellow To connection plug X1171 of the ABS control unit, PIN 42, tie back
excess length in LHD cars
-------------------------------------------------------------------------------
In automatic cars with M62 B44 engine and DSC, from
production date 9/97 to production date 9/98
To connection plug X1171 of the ABS control unit, PIN 73, tie back
excess length in LHD cars

D Supplementary wiring harness for - -

navigation systems in cars with a
production date after 9/98
D1 Black 6-pin plug casing - To branch B2, black 6-pin socket casing, of the navigation system
wiring harness B
D2 1-pin blade terminal contact white/yellow To light module X10117 in black 54-pin socket casing, PIN 38
D3 1-pin blade terminal contact red/yellow To joint connector X10183 (yellow/red cable on joint connector), if D3
is not required, insulate with a shrink hose and tie back, tie back excess
length in LHD cars
D4 1-pin blade terminal contact yellow/white To joint connector X10184 (yellow/white cable on joint connector), if
D4 is not required, insulate with a shrink hose and tie back, tie back
excess length in LHD cars
D5 1-pin blade terminal contact red/yellow To black 42-pin connection plug X1170 of the ABS hydraulic unit in
PIN 35, if D5 is not required, insulate and tie back with shrink hose
D6 1-pin blade terminal contact yellow/white To black 42-pin connection plug X1170 of the ABS hydraulic unit in
PIN 18, if D6 is not required, insulate and tie back with shrink hose

E Aerial extension for the GPS aerial - -

E1 Coaxial plug casing - To GPS aerial (6)
E2 Coaxial socket casing - To the navigation computer (22)

F Additional tacho A signal cable - -

F1 Black 1-pin black/white With 2-way insulation-piercing connector to tacho A signal, black/white
socket casing cable, PIN 10 of branch A3, black 17-pin plug casing of the on-board
monitor wiring harness A
F2 1-pin blade terminal contact black/white Connect to white 18-pin instrument cluster connection plug X10113
Terminal TAA in PIN 3
F3 1-pin blade terminal contact white Insulate with a shrink hose and tie back
Terminal TAA

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/11
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
4. Installation and cabling diagram of the on-board monitor wiring harness

A5
A3
A2
A1 A11 A12 A9 A8
A4 A7
A A6
A13
A15 A16 A14
A10
X13016 039 0528 B

The on-board monitor wiring harness A is to be laid along the audio or main wiring harness and secured with
0

cable ties as shown in the figure.

When installing the on-board monitor wiring harness A, start at the earth post X13016 near the
C pillar at the rear left.
Screw branch A10 to the earth post connection X13016 near the C pillar at the rear left.
Route branch A4 to the installation site for the left TV amplifier on the left-hand C pillar and tie back (only to
be connected if you are also installing a video module and the TV amplifier)
Route branches A11 and A12 to the aerial amplifier on the left-hand C pillar
Route branch A5 to the installation site for the right TV amplifier on the right-hand C pillar and tie back (only
to be connected if you are also installing a video module and the TV amplifier)
Route branches A6 to A9 through the passage grommet in the rear window shelf into the boot to the
installation site for the on-board monitor radio in the rear left side part
Tie back branches A6 to A17 (only to be connected if you are also installing a video module and TV amplifier)
Route branches A13 to A16 through the passage grommet behind the rear seat backrest along the main
cable loom into the boot
Route branches A13 and A14 to the installation site of the on-board monitor radio in the rear left side part
Route branch A15 to the installation site of the video module bracket at the front in the rear left side part and
clip onto the securing clip
Branch A16 to the installation site of the navigation computer in the rear left side part

The on-board monitor wiring harness A crosses behind the left front seat and is to be routed from there
along the cardan tunnel behind the centre console to the installation site of the on-board monitor."

Route branches A1 to A3 along the standard audio wiring harness to the installation site of the on-board
monitor in the instrument panel

Tie back any excess lengths.

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/12
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
5. Installation and cabling diagram of the supplementary wiring harness for the
navigation system in cars with a production date prior to 9/98

C4
C3 C
C5
C6

RHD C5 C2
C1
RHD C6

039 0530 B

The supplementary wiring harness for the navigation system C is to be installed in cars with a production date
0

prior to 9/98 as shown in the figure and secured with cable ties.

When routing the supplementary wiring harness for the navigation system C, start with branch
C1.
Branch C1 to the installation site of the video module bracket at the front in the rear left of the boot
Branch C2 to the earth post connection X10305 below the left tail light
Branches C3 to C6 along the closing panel to the right side part, from there through the passage grommet
in the rear window shelf into the vehicle interior and from there along the right main cable loom to the
installation site of the light module in the A pillar on the right
Branch C3 to the earth post connection X10012 in the front of the right door sill
Branches C5 and C6 to the installation site of the ABS control unit on the left next to the glove compartment
or in RHD cars behind the heating box to the left to the ABS control unit on the right next to the glove
compartment
Tie back any excess lengths.

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/13
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
6. Installation and cabling diagram of the supplementary wiring harness for the
navigation system in cars with a production date after 9/98

D2 D

D5 D6
D3
D4

RHD D3 D1
RHD D4

039 0531 B

The supplementary wiring harness for the navigation system D is to be installed in cars with a production date
0

after 9/98 as shown in the figure and secured with cable ties.

When installing the supplementary wiring harness for the navigation system D, start with branch
D1.
Branch D1 to the installation site of the video module bracket at the front in the rear left of the boot
Branches D2 to D6 along the closing panel to the right side part, from there through the passage grommet
in the rear window shelf into the vehicle interior and from there along the right main cable loom to the
installation site of the light module in the A pillar on the right
Branches D3 and D4 to the joint connectors behind the glove compartment or, in RHD cars, behind the
heating box and to the left to the joint connectors behind the glove compartment
Branches D5 and D6 through the passage grommet in the bulkhead into the engine compartment to the
right to the installation site of the ABS hydraulic unit

Tie back any excess lengths.

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/14
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
7. To install the additional tacho A signal cable in cars with a production date after 9/
99, without tacho A signal on the radio connection plug X18126

On cars with a production date after 9/99, check whether there is still a tacho A signal at the radio
connection plug X18126, PIN 10, black/white cable, in the instrument panel. If there is no tacho A
signal, the following work must be completed in addition."

34
The figure shows the installation site of the
instrument cluster in a LHD car. Proceed in exactly
8 the same way in RHD cars."
F
Open and release the white 18-pin instrument cluster
F1 connection plug X10113.
Connect branch F2, 1-pin socket contact, black/white
cable on the additional tacho A signal cable F, to the free
F3 slot PIN3 on the connection plug X10113.
Insulate and tie back branch F3, 1-pin socket contact,
F2 white cable, with a shrink hose (8).
Then lock and close connection plug X10113 again.
X10113 039 0532 B
Route branch F1, black 1-pin socket casing, black/white
cable, to the radio connection plug X18126 in the
instrument panel and secure it with cable ties (34).

Cut off the excess length of the additional tacho A signal

0

A cable F, black/white cable, near branch F1.

Then use a 2-way insulation-piercing connector (9) to
F connect the free cable end to the tacho A signal, black/
F1 white cable, PIN 10 of branch A3, black 17-pin plug
X18126 casing of the on-board monitor wiring harness A.
A3
9 F
A3
PIN10
039 0534 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/15
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
8. To install the on-board monitor wiring harness, on-board monitor and on-board
monitor radio

The figure shows the left C pillar from the inside."

A5 Screw branch A10, 6 mm cable eyelet, of the on-board
A4
monitor wiring harness A onto earth post connection
A10 X13016 on the C pillar at the rear left.
Tie back branch A4, coaxial plug casing, of the on-board
monitor wiring harness A using a cable tie (34) (only to be
connected if you are also installing a video module and
the TV amplifier).
34
Route branch A5, coaxial plug casing, of the on-board
X13016 monitor wiring harness A on the rear window shelf along
A6-A9 the rear window to the installation site of the right TV
039 0535 B amplifier to the C pillar on the right and tie it back with
cable ties (34) (only to be connected if you are also
installing a video module and the TV amplifier).
Route branches A6 to A9 through the passage grommet
in the rear window shelf into the boot to the installation
site for the on-board monitor radio in the rear left side
part.

Unscrew the existing coaxial plug casing (50) from the

0

aerial amplifier (51) and tie it back (no longer required).

Screw branch A12, coaxial plug casing, of the on-board
52
51 monitor wiring harness A to the released coaxial socket
casing (52) of the aerial amplifier (51).
50 Unplug the existing coaxial socket casing (53) from the
54 53 aerial amplifier (51) and tie it back (no longer required).
Connect branch A11, coaxial socket casing, of the on-
board monitor wiring harness A onto the released coaxial
plug casing (54) of the aerial amplifier (51).

A12
A11 039 0536 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/16
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
8. To install the on-board monitor wiring harness, on-board monitor and on-board monitor radio

50 Before the work steps are carried out as shown in

51 the figure, the new module holder of the on-board
monitor (14) must be equipped as described in the
14 TIS."
38 Connect branch A3, black 17-pin plug casing on the on-
A3 52 board monitor wiring harness A, to the existing radio
38 connection plug X18126.
Affix a rattle guard (38) to the second rattle guard (38) and
then affix them to the wiring harness so that they enclose
X18126 A2 the existing angled coaxial socket casing (50), the black
coaxial socket casing (51) (aerial connection), the
A1 connection plug for the receiver (52) and the plug
A 039 0537 B connection A3+X18126.
The enclosed connections (50, 51, 52) and the wrapped
plug connection A3+X18126 are no longer required and
are to be placed behind the heating control.

0
0
0

Screw the on-board monitor holding pin (13) onto the on-
0

52 board monitor (12).

Connect branch A1, blue 12-pin socket casing, of the on-
board monitor wiring harness A to the blue plug casing
51 (50) on the on-board monitor (12).
Connect branch A2, white 12-pin socket casing, of the
A1 A2 on-board monitor wiring harness A to the white plug
casing (51) on the on-board monitor (12).
Then insert the cables into the on-board monitor slot (52)
12 and carefully slide the on-board monitor (12) into
position.
50
13 039 0538 B
As you insert the holder ensure that no cables/
leads are damaged."
0
0
0
0

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/17
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
8. To install the on-board monitor wiring harness, on-board monitor and on-board monitor radio

Screw the on-board monitor (12) to the module holder of

0

the on-board monitor (14) with four fillister head Philips

screws M3x8 (15).
14 Then put the on-board monitor cover (16) onto the on-
board monitor (12).
12
INFO
1 4

2 5
3 6 TONE SELECT
FM AM

16
MODE MENU

15

039 0539 B
0

50 The figure shows the boot at the rear left."

Insert plastic expanding nuts 4.8 (28) into the cross strut
(50) in the side part at the rear left.
Place another plastic expanding nut 4.8 (28) into the
28 frame part at the rear left.

28

039 0540 B
0

Place the DSP amplifier holder (18) in the boot at the rear
0

26 left onto the mounting bolt (50) and secure it with two
18 hexagonal self-tapping screws and washers 4.8x16 (27).
Place a speed nut M5 (26) onto the DSP amplifier holder
27 (18).

50

039 0541 B
0

Affix the sealing strip (36) to the base holder (19).

0

Place five speed nuts M5 (26) onto the base holder (19)
18 and screw the base holder (19) onto the boot floor at the
rear left using two plastic cap nuts (29) and an hexagonal
self-tapping screw with washer 4.8x16 (27).
30 Then insert two rubber grommets (30) into the recesses
provided in the holder for the DSP amplifier (18) and in
36 the base holder (19).

19 26
29 29
0
26 27 039 0542 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/18
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
8. To install the on-board monitor wiring harness, on-board monitor and on-board monitor radio

Secure the front video module bracket (20) to the base

0

holder (19) with two hexagonal screws and washers

M5x14 (25) and to the mounting bolt (50) using a plastic
20 cap nut (29).

25
29

19
50
039 0543 B

Push the on-board monitor radio (17) into the rubber

0

grommets (30) inserted previously.

Insert the holder for the on-board monitor radio and CD
changer (21) and screw onto the base holder (19) using
three hexagonal screws and washers M5x14 (25).
Screw the on-board monitor radio (17) onto the holder for
the on-board monitor radio and CD changer (21) using a
24/25 hexagonal nut and washer M5 (24) or with a hexagonal
screw and washer M5x14 (25), depending on the design
21 of the on-board monitor radio.
25 19
30 17

039 0544 B

Remove the blue locking clip (50) from branch A13, black
0

A14 17-pin socket casing, of the on-board monitor wiring

harness A and connect branch A14, 10-pin socket
A13 casing, of the on-board monitor wiring harness A to
branch A13.

If the car has a CD changer without a DSP

amplifier, the on-board monitor radio/CD changer
50 control cable must also be fitted.
Secure branch A14 with the blue locking clip (50).

039 0545 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/19
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
8. To install the on-board monitor wiring harness, on-board monitor and on-board monitor radio

0
0
0

Connect branch A8, black coaxial socket casing (aerial

0

A7 connection), of the on-board monitor wiring harness A to

A6 the on-board monitor radio (17).
34 Connect branch A9, angled coaxial socket casing, of the
35 on-board monitor wiring harness A to the on-board
A13 monitor radio (17).
A9 Connect branch A13, black 17-pin socket casing, of the
on-board monitor wiring harness A to the on-board
monitor radio (17).
17 Insert the cable holder (35) into the hole (50) in the holder
50 for the on-board monitor radio and CD changer (21).
A15 A8 Secure the cables of the connected branches A8 and A9
and, if present, the control cable for the on-board monitor
10 21 039 0546 B radio/CD changer using the cable holder (35).
Clip branch A15, white 6-pin plug casing, of the on-board
monitor wiring harness A into the securing clip (10) (it is
subsequently clipped onto the front video module
bracket).
Tie back branches A6 and A7, angled coaxial socket
casing, of the on-board monitor wiring harness A to the
on-board monitor wiring harness A using cable tie (34).

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/20
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
9. To install the supplementary wiring harness for navigation systems in cars with a
production date prior to 9/98

Clip the securing clip (10) with the clipped in branch A15
0

of the on-board monitor wiring harness A into the front

C1 video module bracket (20).
Clip branch C1, black 6-pin plug casing, of the
A supplementary wiring harness for the navigation system
10
C onto branch A15.
C C2 A15 Screw branch C2, 6 mm cable eyelet, onto the earth post
connection X10305 below the left tail light.
20 Route the supplementary wiring harness for the
34 navigation system C along the closing panel to the right
X10305 side part and from there to the passage grommet in the
boot at the top right and attach using cable ties (34).

039 0547 B

Route the supplementary wiring harness for the

0

C navigation system C with branches C3, C4, C5 and C6

through the passage grommet (50) into the vehicle
interior and along the right main cable loom to the
installation site of the light module in the A pillar on the
50 right and secure with cable ties (34).

34

039 0548 B

Screw branch C3, 6 mm cable eyelet, onto the earth post

0

connection X10012 in the front area of the right-hand

C door sill.

C3

X10012 039 0549 B

Remove the light module (50), unplug the black 54-pin

0

socket casing X10117 from the light module (50) and

C4 open it.
Connect branch C4, 1-pin blade terminal contact, white/
yellow cable, to PIN 38 of the black 54-pin socket casing
X10117 X10117.
Then close the black socket casing X10117, plug it in
and reinstall the light module (50).
Tie back any excess length on the supplementary wiring
harness for the navigation system C before branch C4.
50

039 0550 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/21
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
9. To install the supplementary wiring harness for navigation systems
in cars with a production date prior to 9/98

The figure shows the installation in a LHD car.

Proceed in exactly the same way on a RHD car."
In left-hand drive cars, route branches C5 and C6 of the
supplementary wiring harness for the navigation system
C5 C to the ABS control unit (50) on the left by the side of the
glove compartment (excess length must be tied back).
C6 51 In RHD cars, route branches C5 and C6 of the
34 supplementary wiring harness for the navigation system
C behind the heating box to the left to the ABS control
unit on the right next to the glove compartment. Remove
X1171 50 the ABS control unit (50).
Disconnect and dismantle the control unit connector
039 0551 B
X1171. Insert branches C5 and C6 into the plug-in
guide (51).
Connect branch C5, 1-pin blade terminal contact, black
cable, to PIN 9 of the control unit connector X1171. If
PIN 9 is already occupied, cut off the contact part from
branch C5 and solder the black cable onto the cable of
PIN 9 in the installation space of the ABS plug and
insulate it.
Connect branch C6, 1-pin blade terminal contact, yellow
cable, to PIN 42 of the control unit connector X1171. If
PIN 42 is already occupied, cut off the contact part from
branch C6 and solder the yellow cable onto the cable of
PIN 42 in the installation space of the ABS plug and
insulate it.
Assemble the control unit connector X1171 again and
connect it to the ABS control unit (50).
Install the ABS control unit (50) and fasten the
supplementary wiring harness for the navigation system
C with cable ties (34).
Only for automatic cars with M62 B44 engine and
DSC, from production date 9/97 to production
date 9/98.
Connect branch C5, 1-pin blade terminal contact, black
cable, to PIN 72 of the control unit connector X1171. If
PIN 72 is already occupied, cut off the contact part from
branch C5 and solder the black cable onto the cable of
PIN 72 in the installation space of the ABS plug and
insulate it.
Connect branch C6, 1-pin blade terminal contact, yellow
cable, to PIN 73 of the control unit connector X1171. If
PIN 73 is already occupied, cut off the contact part from
branch C6 and solder the yellow cable onto the cable of
PIN 73 in the installation space of the ABS plug and
insulate it.
Assemble the control unit connector X1171 again and
connect it to the ABS control unit (50).
Install the ABS control unit (50) and fasten the
supplementary wiring harness for the navigation system
C with cable ties (34).

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/22
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
10. To choose installation of the supplementary wiring harness for navigation systems
in cars with a production date after 9/98
0

The figure shows the engine compartment, front

right."
Disconnect the black 42-pin connection plug X1170
from the ABS hydraulic unit (50) in the engine
50 compartment at the front right, open it and check
PIN35 whether PIN 18 and PIN 35 are occupied.
If PIN 18 and PIN 35 are not occupied, install the
supplementary wiring harness for the navigation system
PIN18 as described in section 11.
Section 11. To install the supplementary wiring harness
X1170 for navigation systems in cars with a production date after
039 0552 B 9/98 (PIN 18 and PIN 35 on the connection plug of the
ABS hydraulic unit not occupied).
If PIN 18 and PIN 35 are occupied, install the
supplementary wiring harness for the navigation system
as described in section 12.
Section 12. To install the supplementary wiring harness
for navigation systems in cars with a production date after
9/98 (PIN 18 and PIN 35 on the connection plug of the
ABS hydraulic unit occupied).
If PIN 18 is occupied and PIN 35 is not occupied, install
the supplementary wiring harness for the navigation
system as described in section 13.
Section 13. To install the supplementary wiring harness
for navigation systems in cars with a production date after
9/98 (PIN 18 occupied and PIN 35 not occupied on the
connection plug of the ABS hydraulic unit).
If PIN 18 is not occupied and PIN 35 is occupied, install
the supplementary wiring harness for the navigation
system as described in section 14.
Section 14. To install the supplementary wiring harness
for navigation systems in cars with a production date after
9/98 (PIN 18 not occupied and PIN 35 occupied on the
connection plug of the ABS hydraulic unit).

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/23
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
11. To install the supplementary wiring harness for navigation systems in cars with a
production date after 9/98 (PIN 18 and PIN 35 on the connection plug of the ABS
hydraulic unit not occupied)

The figure shows the engine compartment at the

D1 rear left."

A Clip the securing clip (10) with the clipped in branch A15
10 of the on-board monitor wiring harness A into the front
D video module bracket (20).
A15 Clip branch D1, black 6-pin plug casing, of the
supplementary wiring harness for the navigation system
20 34 D onto branch A15.
Route the supplementary wiring harness for the
navigation system D along the closing panel to the right
side part and from there to the passage grommet in the
boot at the top right. Secure the supplementary wiring
039 0553 B
0
harness for the navigation system D with cable ties (34).
Route the supplementary wiring harness for the
0

D navigation system D with branches D2, D3, D4, D5 and

D6 through the passage grommet (50) into the vehicle
interior and along the right main cable loom to the
installation site of the light module in the A pillar on the
50 right and secure with cable ties (34).

34

039 0554 B
0

Remove the light module (50), unplug the black 54-pin

0

D2 socket casing X10117 from the light module (50) and

open it.
Connect branch D2, 1-pin blade terminal contact, white/
X10117 yellow cable, to PIN 38 of the black 54-pin socket casing
X10117.
Then close the black socket casing X10117, plug it in
and reinstall the light module (50).
Tie back any excess length on the supplementary wiring
harness for the navigation system D before branch D2.
50

039 0555 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/24
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
11. To install the supplementary wiring harness for navigation systems in cars with a production date
after 9/98 (PIN 18 and PIN 35 on the connection plug of the ABS hydraulic unit not occupied)

D
0

Remove the cover from the control unit box in the

right of the engine compartment before routing the
supplementary wiring harness for the navigation
system any further."
D5 D6 D3
D4 Insulate branches D3 and D4 of the supplementary
wiring harness for the navigation system D with shrink
hose and tie back in the area of the right front door sill.
Route branches D5 and D6 of the supplementary wiring
harness for the navigation system D through the passage
grommet in the bulkhead, front right, into the control unit
box and from there on to the ABS hydraulic unit. Connect
039 0556 B it to the connection plug X1170 of the ABS hydraulic
unit.
0

50 The figure shows the area behind the glove

compartment in a left-hand drive car. You should
proceed in the identical sequence for right-hand
drive cars."
Feed the supplementary wiring harness for the navigation
system D with branches D5 and D6 through the passage
grommet (50) in the bulkhead, front right, to the control
unit box in the engine compartment and fasten with cable
37 D3 D4 ties (34).
D Push a shrink hose (37) onto branch D3, 1-pin blade
terminal contact, yellow/red cable, and onto branch D4,
1-pin blade terminal contact, yellow/white cable, of the
34 039 0557 B
supplementary wiring harness for the navigation system
D to insulate them and shrink the hoses with a hot air
blower.
Then tie back branches D3 and D4 near the front right
door sill with cable ties (34).

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/25
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
 Carefully cut the rubber grommet (50) on the control unit
0

BMW PIN18
box at the front and carefully push the supplementary
wiring harness for the navigation system D with branches
34
PIN35 X1170 D5 and D6 through the opening in the rubber grommet
(50) and route them to the ABS hydraulic unit (51).
51
Seal the opening in the rubber grommet (50) with
silicone (splash-water protection) after installation
of the supplementary wiring harness for the
D5 navigation system D."
50 D
D6 Unfasten the black 42-pin connection plug X1170 of the
ABS hydraulic unit and connect branches D5 and D6 as
039 0558 B follows:
Connect branch D5, 1-pin blade terminal contact, yellow/
red cable, to the connection plug X1170 of the ABS
hydraulic unit, slotPIN 35.
Connect branch D6, 1-pin blade terminal contact, yellow/
white cable, to the connection plug X1170 of the ABS
hydraulic unit, slotPIN 18.
Close the connection plug X1170 again and connect it to
the ABS hydraulic unit.
Then use cable ties (34) to fasten the supplementary
wiring harness for the navigation system D in the area of
the engine compartment.

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/26
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
12. To install the supplementary wiring harness for navigation systems in cars with a
production date after 9/98 (PIN 18 and PIN 35 on the connection plug of the ABS
hydraulic unit occupied)

The figure shows the boot at the rear left."

D1 Clip the securing clip (10) with the clipped in branch A15
A of the on-board monitor wiring harness A into the front
10 video module bracket (20).
D Clip branch D1, black 6-pin plug casing, of the
A15 supplementary wiring harness for the navigation system
D onto branch A15.
20 34 Route the supplementary wiring harness for the
navigation system D along the closing panel to the right
side part and from there to the passage grommet in the
boot at the top right. Secure the supplementary wiring
harness for the navigation system D with cable ties (34).
039 0553 B
0

Route the supplementary wiring harness for the

0

D navigation system D with branches D2, D3, D4, D5 and

D6 through the passage grommet (50) into the vehicle
interior and along the right main cable loom to the
installation site of the light module in the A pillar on the
50 right and secure with cable ties (34).

34

039 0554 B
0

Remove the light module (50), unplug the black 54-pin

0

D2 socket casing X10117 from the light module (50) and

open it.
Connect branch D2, 1-pin blade terminal contact, white/
X10117 yellow cable, to PIN 38 of the black 54-pin socket casing
X10117.
Then close the black socket casing X10117, plug it in
and reinstall the light module (50).
Tie back any excess length on the supplementary wiring
harness for the navigation system D before branch D2.
50

039 0555 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/27
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
12. To install the supplementary wiring harness for navigation systems in cars with a production date
after 9/98 (PIN 18 and PIN 35 on the connection plug of the ABS hydraulic unit occupied)

Insulate branches D5 and D6 of the supplementary

0

D wiring harness for the navigation system D with shrink

hose and tie back in the area of the right front door sill.
In LHD cars, route branches D3 and D4 of the
D5 supplementary wiring harness for the navigation system
D6 D to the joint connector box behind the glove
D3 compartment (tie back excess length) and connect to the
D4 joint connectors X10183 and X10184.
In RHD cars, route branches D3 and D4 of the
RHD D3 supplementary wiring harness for the navigation system
RHD D4 D behind the heating box left to the joint connector box
behind the glove compartment and connect it to the joint
039 0562 B connectors X10183 and X10184.
0

50 The figure shows the area behind the glove

compartment in a left-hand drive car. You should
proceed in the identical sequence for right-hand
drive cars."
Push a shrink hose (37) onto branch D5, 1-pin blade
terminal contact, yellow/red cable, and onto branch D6,
1-pin blade terminal contact, yellow/white cable on the
D3 D supplementary wiring harness for the navigation system
37 D5 D to insulate them and shrink the hoses with a hot air
D4 D6 blower.

34 039 0563 B Then tie back branches D5 and D6 near the front right
door sill with cable ties (34).
Connect branch D3, 1-pin blade terminal contact, yellow/
red cable, onto the joint connector X10183 (yellow/red
cable on the joint connector) in the joint connector box
(50) behind the glove compartment.
Connect branch D4, 1-pin blade terminal contact, yellow/
white cable, onto the joint connector X10184 (yellow/
white cable on the joint connector) in the joint connector
box (50) behind the glove compartment.
Tie back excess lengths of branches D3 and D4 with
cable ties (34).

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/28
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
13. To install the supplementary wiring harness for navigation systems in cars with a
production date after 9/98 (PIN 18 occupied and PIN 35 not occupied on the
connection plug of the ABS hydraulic unit)

The figure shows the boot at the rear left."

D1 Clip the securing clip (10) with the clipped in branch A15
of the on-board monitor wiring harness A into the front
A video module bracket (20).
10
Clip branch D1, black 6-pin plug casing, of the
D A15 supplementary wiring harness for the navigation system
D onto branch A15.
20 34 Route the supplementary wiring harness for the
navigation system D along the closing panel to the right
side part and from there to the passage grommet in the
boot at the top right. Secure the supplementary wiring
harness for the navigation system D with cable ties (34).
039 0553 B
0

Route the supplementary wiring harness for the

0

D navigation system D with branches D2, D3, D4, D5 and

D6 through the passage grommet (50) into the vehicle
D

05

interior and along the right main cable loom to the

43

B 45 0 93

installation site of the light module in the A pillar on the

50 right and secure with cable ties (34).

34

039 0554 B
0

Remove the light module (50), unplug the black 54-pin

0

D2 socket casing X10117 from the light module (50) and

open it.
Connect branch D2, 1-pin blade terminal contact, white/
yellow cable, to PIN 38 of the black 54-pin socket casing
X10117 X10117.
Then close the black socket casing X10117, plug it in
and reinstall the light module (50).
Tie back any excess length on the supplementary wiring
harness for the navigation system D before branch D2.
50

039 0555 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/29
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
13. To install the supplementary wiring harness for navigation systems in cars with a production date
after 9/98 (PIN 18 occupied and PIN 35 not occupied on the connection plug of the ABS hydraulic unit)

D Before further installation of the supplementary

wiring harness for the navigation system, you
should remove the cover for the control unit box in
the engine compartment on the right."
D5 D6 Route branches D5 and D6 of the supplementary wiring
D3 harness for the navigation system D through the passage
D4 grommet in the bulkhead, front right, into the control unit
box and from there onwards to the ABS hydraulic unit.
RHD D3 Only connect branch D5 to connection plug X1170 on
RHD D4 the ABS hydraulic unit.
Insulate branch D6 with a shrink hose and tie it back.
In LHD cars, route branches D3 and D4 of the
039 0567 B supplementary wiring harness for the navigation system
D to the joint connector box behind the glove
compartment (the excess length must be tied back).
In RHD cars, route branches D3 and D4 behind the
heating box left to the joint connector box behind the
glove compartment and secure them with cable ties.
Insulate branch D3 with a shrink hose and tie it back.
Only connect branch D4 to the joint connector X10184.

50 The figure shows the area behind the glove

compartment in a left-hand drive car. You should
51 proceed in the identical sequence for right-hand
drive cars."
Feed the supplementary wiring harness for the navigation
system D with branches D5 and D6 through the passage
grommet (50) in the bulkhead, front right, to the control
unit box in the engine compartment and fasten with cable
37 D3 D4 ties (34).
D Push a shrink hose (37) onto branch D3, 1-pin blade
terminal contact, yellow/red cable. Use a hot air blower to
shrink the insulation and tie it back.
34 039 0568 B Then connect branch D4, 1-pin blade terminal contact,
yellow/white cable, onto the joint connector X10184
(yellow/white cable on the joint connector) in the joint
connector box (51) behind the glove compartment.
Tie back excess lengths of branches D3 and D4 with
cable ties (34).

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/30
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
13. To install the supplementary wiring harness for navigation systems in cars with a production date
after 9/98 (PIN 18 occupied and PIN 35 not occupied on the connection plug of the ABS hydraulic unit)

Carefully cut the rubber grommet (50) on the control unit

0

37
BMW box at the front and carefully push the supplementary
wiring harness for the navigation system D with branches
34 D5 and D6 through the opening in the rubber grommet
PIN35 X1170 (50) and route them to the ABS hydraulic unit (51).

51 Seal the opening in the rubber grommet (50) with

silicone (splash-water protection) after installation
of the supplementary wiring harness for the
D5 navigation system D."
50 D Unfasten the black 42-pin connection plug X1170 of the
D6 ABS hydraulic unit and connect branch D5 as follows:
039 0569 B
Connect branch D5, 1-pin blade terminal contact, yellow/
red cable, to the connection plug X1170 of the ABS
hydraulic unit, slotPIN 35.
Push a shrink hose (37) onto branch D6, 1-pin blade
terminal contact, yellow/white cable. Use a hot air blower
to shrink the insulation and tie it back.
Close the connection plug X1170 again and connect it to
the ABS hydraulic unit.
Then use cable ties (34) to fasten the supplementary
wiring harness for the navigation system D in the area of
the engine compartment.

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/31
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
14. To install the supplementary wiring harness for navigation systems in cars with a
production date after 9/98 (PIN 18 not occupied and PIN 35 occupied on the
connection plug of the ABS hydraulic unit)

The figure shows the boot at the rear left."

D1 Clip the securing clip (10) with the clipped in branch A15
of the on-board monitor wiring harness A into the front
A video module bracket (20).
10
Clip branch D1, black 6-pin plug casing, of the
D A15 supplementary wiring harness for the navigation system
D onto branch A15.
20 34 Route the supplementary wiring harness for the
navigation system D along the closing panel to the right
side part and from there to the passage grommet in the
boot at the top right. Secure the supplementary wiring
harness for the navigation system D with cable ties (34).
039 0553 B
0

Route the supplementary wiring harness for the

0

D navigation system D with branches D2, D3, D4, D5 and

D6 through the passage grommet (50) into the vehicle
interior and along the right main cable loom to the
installation site of the light module in the A pillar on the
50 right and secure with cable ties (34).

34

039 0554 B
0

Remove the light module (50), unplug the black 54-pin

0

D2 socket casing X10117 from the light module (50) and

open it.
Connect branch D2, 1-pin blade terminal contact, white/
yellow cable, to PIN 38 of the black 54-pin socket casing
X10117 X10117.
Then close the black socket casing X10117, plug it in
and reinstall the light module (50).
Tie back any excess length on the supplementary wiring
harness for the navigation system D before branch D2.
50

039 0555 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/32
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
14. To install the supplementary wiring harness for navigation systems in cars with a production date
after 9/98 (PIN 18 not occupied and PIN 35 occupied on the connection plug of the ABS hydraulic unit)

D Remove the cover from the control unit box in the

right of the engine compartment before routing the
supplementary wiring harness for the navigation
system any further.."
D5 D6 Route branches D5 and D6 of the supplementary wiring
D4 harness for the navigation system D through the passage
grommet in the bulkhead, front right, into the control unit
D3 box and from there onwards to the ABS hydraulic unit.
RHD D4 Insulate branch D5 with a shrink hose and tie it back.
Only connect branch D6 to connection plug X1170 on
RHD D3 the ABS hydraulic unit.
In LHD cars, route branches D3 and D4 of the
039 0573 B supplementary wiring harness for the navigation system
D to the joint connector box behind the glove
compartment (the excess length must be tied back).
In RHD cars, route branches D3 and D4 behind the
heating box left to the joint connector box behind the
glove compartment and secure them with cable ties.
Only connect branch D3 to the joint connector X10183.
Insulate branch D4 with a shrink hose and tie it back.

50 The figure shows the area behind the glove

compartment in a left-hand drive car. You should
proceed in the identical sequence for right-hand
51 drive cars."
Feed the supplementary wiring harness for the navigation
system D with branches D5 and D6 through the passage
grommet (50) in the bulkhead, front right, to the control
unit box in the engine compartment and fasten with cable
37 D3 D4 ties (34).
D Push a shrink hose (37) onto branch D4, 1-pin blade
terminal contact, yellow/white cable. Use a hot air blower
to shrink the insulation and tie it back.
34 039 0574 B Connect branch D3, 1-pin blade terminal contact, yellow/
red cable, onto the joint connector X10183 (yellow/red
cable on the joint connector) in the joint connector box
(51) behind the glove compartment.
Tie back excess lengths of branches D3 and D4 with
cable ties (34).

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/33
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
14. To install the supplementary wiring harness for navigation systems in cars with a production date
after 9/98 (PIN 18 not occupied and PIN 35 occupied on the connection plug of the ABS hydraulic unit)

Carefully cut the rubber grommet (50) on the control unit

0

BMWPIN18
37 box at the front and carefully push the supplementary
34 wiring harness for the navigation system D with branches
X1170 D5 and D6 through the opening in the rubber grommet
(50) and route them to the ABS hydraulic unit (51).

51
Seal the opening in the rubber grommet (50) with
silicone (splash-water protection) after installation
of the supplementary wiring harness for the
D5 navigation system D."
50 D
Unfasten the black 42-pin connection plug X1170 of the
D6 ABS hydraulic unit and connect branch D6 as follows:
039 0575 B
Connect branch D6, 1-pin blade terminal contact, yellow/
white cable, to the connection plug X1170 of the ABS
hydraulic unit, slotPIN 18.
Push a shrink hose (37) onto branch D5, 1-pin blade
terminal contact, yellow/red cable. Use a hot air blower to
shrink the insulation and tie it back.
Close the connection plug X1170 again and connect it to
the ABS hydraulic unit.
Then use cable ties (34) to fasten the supplementary
wiring harness for the navigation system D in the area of
the engine compartment.

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/34
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
15. To install the navigation system

Overview drawing for installation of the navigation system

0

wiring harness B and the aerial extension for the GPS

aerial E.
B5 Navigation system wiring harness B
B1 E1 B3 Branch B1 to the free branch A15 of the on-board
E B6 monitor wiring harness A on the front video module
bracket
B4 Branch B2 to the free branch C1/D1 of the
E2 supplementary wiring harness for the navigation system
C/D on the front video module bracket
Tie back branches B3 and B4 to the navigation system
B2 B wiring harness B
Branches B5 and B6 to the installation site of the
039 0576 B
navigation computer
Aerial extension for the GPS aerial E
Branch E1 to the installation site of the GPS aerial under
the rear window shelf
Branch E2 to the installation site of the navigation
computer

Place the GPS aerial holder (11) on the GPS aerial holder
0

(6) and secure it with two expanding rivets (32).

32

11

039 0577 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/35
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
0

The figure shows rear window shelf on the left."

Remove the prepunched cut-out (50) under the rear
window shelf.
31 Check the existing attachment points (51) are 8 mm in
diameter; if necessary, drill out the attachment points to
8 mm diameter.
51 Press attachment grommets (31) into the attachment
50 points (51).

039 0578 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/36
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
15. To install the navigation system

Fit the GPS aerial holder with the mounted GPS aerial
0

50 6 34 into the attachment grommets (31).

Plug together branches E1, coaxial plug casing, of the
E aerial extension for the GPS aerial E with the aerial cable
(50) of the GPS aerial (6).
Route the aerial extension for the GPS aerial F along the
audio wiring harness through the passage grommet
E1 behind the rear seat backrest to the installation site of the
31 navigation computer in the boot at the rear left and
secure it with cable ties (34).

039 0579 B
0

Place a speed nut M5 (26) onto the front video module

0

50 bracket (20).

24 23 Insert the navigation computer holder (23) and secure it

to the stud bolt (50) on the gutter reinforcement with the
hexagonal nut and washer M5 (24) and to the DSP
amplifier holder and the front video module bracket (20)
18 26 with two hexagonal screws with washers M5x14 (25).

25 If the car is equipped with a car phone or mobile

20 phone, use the existing hexagonal nut and washer
M5 from the telephone holder."

039 0580 B
0

Push branch A16, blue 18-pin socket casing, of the on-

0

board monitor wiring harness A through the navigation

23 computer holder (23).
B5 Push branch B5, blue 18-pin socket casing, and branch
34 B6, Bordeaux 18-pin socket casing, of the navigation
system wiring harness B through the navigation
B6 computer holder (23).
E2 Then tie back branch B5 on the navigation system wiring
34
A16 harness B with a cable tie (34).
Push branch E2, coaxial socket casing, of the aerial
extension for the GPS aerial E through the navigation
computer holder (23).
039 0581 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/37
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
15. To install the navigation system

Tie back branch B3, white 18-pin socket casing and

0

34 C/D
C1/D1 branch B4, black 6-pin plug casing, of the navigation
system wiring harness B to the navigation system wiring
harness B using cable tie (34).
A
A15
Connect branch B2, black 6-pin socket casing, of the
B3 B
navigation system wiring harness B to branch C1/D1,
black 6-pin plug casing, of the supplementary wiring
34 harness for the navigation system C/D.
B1 B4
Connect branch B1, white 6-pin socket casing, of the
navigation system wiring harness B to branch A15, white
6-pin plug casing, of the on-board monitor wiring harness
B2 A.
039 0582 B
Then attach the navigation system wiring harness B, on-
board monitor wiring harness A and supplementary
wiring harness for the navigation system C/D using cable
ties (34).

Connect branch A16, blue 18-pin socket casing, of the

0

B E on-board monitor wiring harness A onto the navigation

23 computer (22).
A Connect branch B6, Bordeaux 18-pin socket casing with
tied back branch B5, of the navigation system wiring
A16 harness B to the navigation computer (22).
Connect branch E2, coaxial socket casing, of the aerial
B6 extension for the GPS aerial E to the navigation computer
E2 (22).
22
When inserting the navigation computer ensure
that you do not jam or damage any cables or lines
(including behind the navigation computer)."
039 0583 B
Slide the navigation computer (22) into the navigation
computer holder (23) until it engages.
Then install the new boot trim for the rear left, which you
ordered separately using the Electronic Parts Catalogue
(EPC).

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/38
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
16. Coding and concluding work

If you also wish to install the video module and TV amplifiers for TV function, the coding and the
concluding work should not be completed until after the video module and TV amplifiers for TV
function have been installed, see section 18)."

Coding
This system requires coding.
To ensure that the retrofit system
- is fully functional and
- prevents malfunctions and errors when combined with other electrical systems in the car, this retrofit
system and, possibly, other components must be coded and saved in the central code of the IKE.
This coding process is automatic using the current coding program in the “Retrofit” path.
The procedure is user-guided, follow the text instructions for completing each individual step.

Procedure
– Connect DIS/MoDIC to the car
– Ignition “ON”
– Select “Coding ZCS”
– Series: “E39”
– Path: “2 Retrofit”
– System: “7 Navigation”

The “Navigation operating software V16” CD ROM is required to load the operating system.
Caution! Do not insert the “Operating software V16” CD ROM into the CD drive yet.
Do not insert the “Operating software V16” CD ROM until asked to do so by the instructions on the
on-board monitor.
At the same time, this “Operating software V16” CD ROM also encodes the language."

- Start automatic coding (confirm with “Y”)

- Follow the instructions on the on-board monitor
- Print out the new central label for the amended coding key and affix it to the car on the right-hand side of
the boot near the battery.
- After the message “Coding complete” appears on the monitor of the DIS/MoDIC, switch the ignition
“OFF”, wait for at least 10 seconds and then switch the ignition “ON” again.
- Print out error memory
- Insert the “Road map” CD ROM into the navigation computer
- Conduct a function test

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/39
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
16. Coding and concluding work

In cars with a DSP amplifier, the DSP amplifier also has to be recoded."

Procedure
- Connect DIS/MoDIC to the car
- Ignition “ON”
- Select “Coding ZCS”
- Series: “E39”
- Path: “1 Recoding”
- System: “82 DSP”
- Start automatic coding (confirm with “Y”)
- After the message “Coding complete” appears on the monitor of the DIS/MoDIC, switch the ignition
“OFF”, wait for at least 10 seconds and then switch the ignition “ON” again.
- Print out error memory
- Conduct a function test

Language coding:
The language coding can be repeated using the “Navigation CD-ROM operating software V16”.

Concluding work
Connect battery
Conduct a function test
Print out the error memory
Assemble the car again following the instructions for dismantling it in reverse order

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/40
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
17. Connection description for TV function

This chapter is only applicable if the car is also to be upgraded with the TV function."
To complete the upgrade the required parts (video module, TV amplifier and small parts) must be ordered
separately using the electronic parts catalogue (EPC) and installed.
The relevant branches of the wiring harnesses also have to be connected as follows:
Undo the tied-back branch A4, coaxial plug casing, of the on-board monitor wiring harness A and plug it onto
the previously mounted left TV amplifier in the left C pillar.
Undo the tied-back branch A5, coaxial plug casing, of the on-board monitor wiring harness A and plug it onto
the previously mounted right TV amplifier in the right C pillar.
Disconnect branch A16, blue 18-pin socket casing, of the on-board monitor wiring harness A from the
navigation computer.
Undo branch B5, blue 18-pin socket casing, which is tied back on the navigation system wiring harness B
and connect it to the blue 18-pin plug casing on the navigation computer.
Undo branches A6, angled coaxial socket casing, and A7, angled coaxial socket casing, which are tied back
on the on-board monitor wiring harness A and undo branch B3, white 18-pin socket casing, which is tied
back on the navigation system wiring harness B.
The route branches A6, A7, A16 and B3 to the video module and connect them to the video module as
follows:
Connect branches A6 and A7, angled coaxial socket casing, to the two coaxial plug casings on the video
module.
Connect branch A16, blue 18-pin socket casing, to the blue 18-pin plug casing of the video module.
Connect branch B3, white 18-pin socket casing, to the white 18-pin plug casing of the video module.

Should the car be equipped at a later date with TV function, the system must be re-coded. For further
details refer to section “16. Coding and concluding work”."

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/41
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
 0

X229
X6500S VB R
RADIO/HIFI
-
X1543
VB 30 RADIO RADIO/HIFI
14 6 12 3 11 2 8 1 16 10 4 7 9 5 13
-
RADRH- RADRH+ RADLH- RADLH+ RADRV- RADRV+ RADLV- RADLV+ ANT TAA TELM I-BUS 30<64 R 58G
RADIO/HIFI
0,35 0,35 2,5 1,5 0,5 X18344 X1362
SWWS WSGRGE RTGN VIWS GRRT VB I-BUS VB 58G
-

Retrofit kit No. 65 90 0 025 171

58G
RADIO/HIFI RADIO/HIFI
0,5 0,5 0,5 0,5 0,5
RTGN WSGRGE RTGN VIWS GRRT

X581 X18344 X1543 X229 X1362 30<64 I/K-BUS 30<64 R<E 58G

Installation Instructions No. 01 29 0 028 309

VB TACHO A VB I-BUS VB 30 RADIO VB R VB 58G X18802 X18801
- - - - 8 RADIO/HIFI 6 7 11 1 RADIO/HIFI
-

RADIO RADIO RADIO RADIO RADIO

/HIFI /HIFI /HIFI /HIFI /HIFI A196

BORDMONITOR
1 2 3 4 5 6 7 12 12 3 4 10 9 2 X18801
VMR VMR31 VMG VMG31 VMB VMB31 VMLC31 PL X18802 PL TAPEL+ TAPEL- TAPER+ TAPER- 31E<RAD

0,35 0,35 0,35 0,5 0,5 0,5 0,5 0,5 0,5 0,5
SW SW SW BRRT SW BLSW BLBR GESW GEBR BR

X1543 X229 X581 X18344

1724213.9 1724213.9 1724213.9 VB 30 RADIO VB R VB TACHO A VB I-BUS

(others see cover sheet)

LTG1-ADR.GESCH. LTG1-ADR.GESCH. LTG1-ADR.GESCH.
- - - -

RADIO RADIO RADIO RADIO

Issue date: 01.2002

/HIFI /HIFI /HIFI /HIFI

0,5 0,5 0,5 0,35 0,35 0,35

RTGN RTGN WSGRGE SCHIRM SCHIRM SCHIRM

30<64 30<64 I/K-BUS VMR VMR31 VMG VMG31 VMB VMB31 VMLC31

1 2 3 7 16 5 14 6 15 12 X18804

10 11 9 18 X18804
A197 RADIO/HIFI
31E<RAD 31E<RAD VM+ VM-

VIDEOMODUL
0,5 0,5
1393906.9 1393905.9 1393904.9 1393903.9 BR BR 1386698.9
1386696.9 1386699.9
LTG VERDRILLT LTG VERDRILLT LTG VERDRILLT LTG VERDRILLT LTG VERDRILLT LTG VERDRILLT LTG VERDRILLT
18. Circuit diagram for on-board monitor wiring harness

X13016
MASSE STEREO/HIFI
-

RADIO/HIFI 1,5 0,5 0,5 0,75

0,75 0,75 0,75 0,75 0,75 0,75 0,75 0,75 0,5 0,35 0,35 0,35 2,5 1,5 0,5 0,5 0,35
0,5 RTGN WSGRGE BR
BROR BLSW BROR GESW BROR BLRT BROR GERT WS SWWS WSBR WSGRGE RTGN VIWS GRRT VIWS SWWS
GERT GEBR

RADRH- RADRH+ RADLH- RADLH+ RADRV- RADRV+ RADLV- RADLV+ ANT TAA TELM I-BUS 30<64 R 58G 30<64 R<E TAA I/K-BUS 31E<RAD
VM+ VM- TAPEL+ TAPEL- TAPER+ TAPER-

16 10 4
X18126 X18805 1 5 4 3 2
14 6 12 3 11 2 8 1 7 9 5 13 RADIO/HIFI 10 5 6 7 1 2 RADIO/HIFI
X1532S
RADIO/HIFI

15 X18126
N9

RADIO
31E<RAD

2,5
BR
X13016 X13016
MASSE STEREO/HIFI MASSE
- -
STEREO/HIFI

Issue date:
RADIO/HIFI
RADIO
/HIFI

039 0584 B

EN/42
18. Circuit diagram for on-board monitor wiring harness

Legend

A196 On-board monitor

A197 Video module
N9 Radio
X229 Connector R
X581 Tacho A connector
X1362 58g connector
X1532 Radio/HiFi navigation
X1543 Connector 30 radio
X6500 Plug connector, adapter
X13016 Earth, stereo/Hi Fi
X18126 Radio A
X18344 I bus connector
X18801 On-board monitor control
X18802 On-board monitor
X18804 Video module A
X18805 Radio B

Colour abbreviations

BR Brown
RT Red
VI Violet
WS White
GR Grey
SW Black
GN Green
GE Yellow
BL Blue

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/43
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
19. Circuit diagram for the navigation system wiring harness

VIDEOMODUL

KAR-KBB NAVIGATION HIFI-KBB A197

X1310B X13318S X1532B X18806
1 2 3 NAVI 1 4 3 2 5 NAVI 5 2 1 3 NAVI 18 17 16 8 7 3 12 NAVI
DFAVL DFAVR RFL GND RXD CTS RTS TXD R 31 30 I-BUS R75 B75 G75 SYNC RGBGND VOICE VOICEGND

8373297.9 8373297.9 1386697.9

MANTEL LTG. LTG. GESCH. LTG. VERDRILLT

0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,5 0,5 0,35 0,35 0,35 0,35 0,35 0,35 0,5 0,5
GERT GEWS WSGE SCHIRM WS SW RT GR VIRT BRSW RTGN WSGRGE RT SW GR WS SCHIRM BLRT BLBR

DFAVL DFAVR RFL GND RXD CTS RTS TXD R 31 30 I-BUS R75 B75 G75 SYNC RGBGND VOICE VOICEGND
X1312 X1313
10 11 1 15 16 14 13 12 3 NAVI 10 1 3 4 13 8 17 15 9 18 NAVI

A112
STG-NAVIGATION

039 0585 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/44
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
19. Circuit diagram for the navigation system wiring harness

Legend

A112 Navigation plug casing

A197 Video module
X1310 KAR navigation
X1312 Navigation A
X1313 Navigation B
X1532 Radio/HiFi navigation
X18806 Video module A
X13318 Navigation/telephone

Colour abbreviations

BR Brown
RT Red
VI Violet
WS White
GR Grey
SW Black
GN Green
GE Yellow
BL Blue

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/45
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
20. Circuit diagram for supplementary wiring harness for navigation systems in cars
with a production date prior to 9/98

X10012
MASSE-IVE
31
SA-LTG

STG ABS/ASC 1.0

BR
Lichtmodul

A3 A52
38 9 (72) 42 (73)

SA-LTG SA-LTG
X11374
RFSI DFAVL DFAVR Schirm
X10117 X1171 SA-LTG
0.35
Schirm

0.35 0.35 0.35

WSGE SW GE

1724214.9
LTG. 2-ADR.
GESCH.

S
RFSI DFAVL DFAVR 31 X1310S
SA-LTG
3 1 2 4

Navigation
0.5
BR

X10305
MASSE SCHIRMLTG.
NAVIGATION
31
SA-LTG

039 0587 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/46
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
20. Circuit diagram for supplementary wiring harness for navigation systems in cars with a production date
prior to 9/98

Legend

A3 Light module
A52 ABS hydraulic unit/ASC
X1171 ABS/ASC
X1310 KAR navigation
X10012 Earth IVE
X0117 Black 54-pin socket casing of the light module
X10305 Navigation earth shield cable
X11374 Shield connector

In automatic cars with the M62 B44 engine and DSC from production date 9/97 to production
date 9/98 only, the DFAVL signal is at PIN 72 and the DFAVR signal is at PIN 73 of the ABS/ASC
control unit connector X1171.

Colour abbreviations

BR Brown
RT Red
VI Violet
WS White
GR Grey
SW Black
GN Green
GE Yellow
BL Blue

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/47
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
21. Circuit diagram for supplementary wiring harness for navigation systems in cars
with a production date after 9/98

Lichtmodul

ABS/DSC
A3 A65
38 35 18

RFSI X10117 DFAVL DFAVR X1170

X10183 X10184
VB DFAVL VB DFAVR

0.35 0.35 0.35 0.35

GERT GERT GEWS GEWS

X001* X002*
VB DFAVL VB DFAVR

0.35 0.35 0.35

WSGE GERT GEWS

RFSI DFAVL DFAVR X1310S

3 1 2
Navigation

039 0586 B

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/48
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002
21. Circuit diagram for supplementary wiring harness for navigation systems in cars with a production date
after 9/98

Legend

A3 Light module
A65 ABS hydraulic unit/DSC
X001* DFAVL connector
X002* DFAVR connector
X1170 Black 42-pin connection plug of ABS/DSC hydraulic unit
X1310S Black 6-pin plug casing
X10117 Black 54-pin socket casing of the light module
X10183 DFAVL joint connector
X10184 DFAVR joint connector

The components marked with an asterisk (*) and X designations are only valid for this circuit diagram, all other
components and X designations comply with the BMW after-sales circuit diagrams.

Colour abbreviations

BR Brown
RT Red
VI Violet
WS White
GR Grey
SW Black
GN Green
GE Yellow
BL Blue
0

Retrofit kit No. 65 90 0 025 171 (others see cover sheet) Issue date: EN/49
Installation Instructions No. 01 29 0 028 309 Issue date: 01.2002