SFAF504G

Isolation 5.0 AMPS. Glass Passivated Super Fast Rectifiers

Voltage Range
200 Volts
Current
5.0 Amperes
ITO-220AC
Features
a Low forward voltage drop .185(4.7)
MAX .406(10.3)MAX

a High current capability .124(3.16)

MAX
.134(3.4)DIA
.113(3.0)DIA
.112(2.85)
.100(2.55)

a High reliability .272(6.9)

a High surge current capability .248(6.3)

.606(15.5)
.583(14.8)

Mechanical Data
.063(1.6)

a Case: ITO-220AC molded plastic

MAX

.161(4.1)

a Epoxy: UL 94V-O rate flame retardant MAX

a Terminals: Leads solderable per MIL-STD-

.110(2.8) .055(1.4) .543(13.8)
.071(1.8)
.098(2.5) MAX .512(13.2)
MAX

202, Method 208 guaranteed .030(0.76)

MAX
.035(0.9)

a Polarity: As marked
MAX

a High temperature soldering guaranteed: .100(2.55) .100(2.55)

250oC/10 seconds .16”,(4.06mm) from

case.
aWeight: 2.24 grams
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25
ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number SFAF504G Units
Maximum Recurrent Peak Reverse Voltage 200 V
Maximum RMS Voltage 140 V
Maximum DC Blocking Voltage 200 V
Maximum Average Forward Rectified Current
.375 (9.5mm) Lead Length @TC = 100
5.0 A
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated Load 125 A
(JEDEC method )
Maximum Instantaneous Forward Voltage 0.975 V
@ 5.0A
Maximum DC Reverse Current @ TA=25
10.0 uA
at Rated DC Blocking Voltage @ TA=100
400 uA
Maximum Reverse Recovery Time (Note 1) 35 nS
Typical Junction Capacitance (Note 2) 70 pF
Typical Thermal Resistance R(Note 3) 5.0
/W
Operating Temperature Range TJ -65 to +150

Storage Temperature Range TSTG -65 to +150

Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C.
3. Thermal Resistance from Junction to Case Mounted on Heatsink.
 RATINGS AND CHARACTERISTIC CURVES ( SFAF504G )

FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM

50W 10W
NONINDUCTIVE NONINDUCTIVE trr
+0.5A

(-)
DUT
(+) PULSE 0
50Vdc GENERATOR
(approx) (NOTE 2) -0.25A
(-) 1W OSCILLOSCOPE
NON (NOTE 1) (+)
INDUCTIVE

NOTES: 1. Rise Time=7ns max. Input Impedance= -1.0A

1 megohm 22pf 1cm
2. Rise Time=10ns max. Sourse Impedance= SET TIME BASE FOR
50 ohms 5/ 10ns/ cm

FIG.2- MAXIMUM FORWARD CURRENT DERATING FIG.3- TYPICAL REVERSE CHARACTERISTICS

CURVE 1000
10
AVERAGE FORWARD CURRENT. (A)

INSTANTANEOUS REVERSE CURRENT. ( A)

TC=100 0C
6 100

2
10

0
0 50 100 150
o
CASE TEMPERATURE. ( C) TC=25 0C
1.0
FIG.4- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
PEAK FORWARD SURGE CURRENT. (A)

TC=125 0C
120
0.1
8.3ms Single Half Sine Wave 0 20 40 60 80 100 120 140
JEDEC Method
90 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)

60 FIG.6- TYPICAL FORWARD CHARACTERISTICS

100
30
INSTANTANEOUS FORWARD CURRENT. (A)

30
1 2 5 10 20 50 100
NUMBER OF CYCLES AT 60Hz 10

FIG.5- TYPICAL JUNCTION CAPACITANCE

3.0
100
Tj=25 0C 1.0
90
CAPACITANCE.(pF)

80 0.3

70 0.1

60
.03
Tj=25oC
50 Pulse Width=300 s
1% Duty Cycle
.01
.4 .6 .8 1.0 1.2 1.4 1.6 1.8
1 2 5 10 20 50 100 200 500
FORWARD VOLTAGE. (V)
REVERSE VOLTAGE. (V)