Scribd
Upload
33 views4 pages

Practice Sheet-2 A

Uploaded by

shivangpal039
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
33 views4 pages

Practice Sheet-2 A

Uploaded by

shivangpal039
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Pranveer Singh Institute of Technology, Kanpur

BME 101/201 Practice Sheet-2 (UNIT-1)


Q1.Three cylinders are piled in a rectangular ditch. Find reaction between cylinder C and vertical wall. Radius of cylinder A=5
cm , B=6cm,C=4cm. Figure-1.

Q2.Three identical cylinders each weighing W are stacked on incline surfaces at angle  with horizontal. Find smallest angle 
to prevent the stack from collapsing.fig-2.

Q3.A 4m long bar AB of negligible weight rests in a horizontal position on smooth inclines. Find distance x at which 100N load
should be placed from B to keep the bar horizontal. Fig-3

Q4.A string of length 60cm is tied to two supports at the same level & 40cm apart.A smooth ring of 400N is tied to the string at
40cm from left end & pulley by a horizontal force P.Find the value of P assuming tension in both sides of string is same.fig-18

Q5.Two cylinders of weight 4KN & 3KN rest on smooth inclined planes as shown in fig-16.They are connected to a weightless
bar hinged to each cylinder at its geometric centre by smooth pins.Find the force P to be applied to smaller cylinder at 45 0 to
vertical to hold the system in given position.

Q6.Figure 10 shows a smooth cylinder of radius 25cm supporting a rod AB 80cm long weighing 120N.End A of rod is hinged to
a horizontal surface AD.Cylinder is also attached to the hinge by a string of length 25cm.Find tension in the string for
equilibrium of the system.

Q7.A frictionless pulley is supported by two bars AB & AC which are hinged at B & C to a vertical wall as shown in fig-19.A
flexible cable DG hinged at D goes over the pulley & supports a load of 15KN at G. Find forces in the bars AB & AC.

1 Fundamental of Mechanical Engineering [BME-101/202]


Pranveer Singh Institute of Technology, Kanpur
BME 101/201 Practice Sheet-2 (UNIT-1)
Q8.Forces F1 & F2 act on a bracket as shown in fig-10. Determine their resultant.

Q9.Find the resultant of four forces acting at point A.fig-6

Q10. Find x and y components of forces P & T, all of which act on A of the bracket as shown in figure 4.

Q11 Forces 2,√3,5,√3 and 2KN are acting at one of angular points of a regular hexagon towards five other angular
points.Find magnitude and direction of resultant force.fig-13

Q12.Determine reactions at points of supports in given figures.

2 Fundamental of Mechanical Engineering [BME-101/202]


Pranveer Singh Institute of Technology, Kanpur
BME 101/201 Practice Sheet-2 (UNIT-1)
Q13- Determine the resultant of the four forces acting on a body as shown in Fig [R = 200; α = 60°; at a
distance y = 8.7679 m below O]]

Q14- A roller of radius r = 300 mm and weight 2000 N is to be pulled over a curb of height 150 mm [Fig.]
by a horizontal force P applied to the end of a string wound tightly around the circumference of the roller.
Find the magnitude of P required to start the roller move over the Curb

Q15- Determine the reactions at A,B and D of system shown in fig [RDV = 16.07KN, RC = 21.43KN, RBV = 8.57KN,
RA = 12.86KN]

Q16- A system of parallel forces is acting on a rigid bar as shown in Fig. Reduce this system
to (i) a single force
(ii) A single force and a couple at A
(iii) A single force and a couple at B.

3 Fundamental of Mechanical Engineering [BME-101/202]


Pranveer Singh Institute of Technology, Kanpur
BME 101/201 Practice Sheet-2 (UNIT-1)
Q17. The frictionless pulley A shown in fig. is supported by two bars AB and AC which are hinged at B
and C to a vertical wall. The flexible cable DG hinged at D goes over the pulley and supported a load of
20 kN at G. The angles between the various members are shown in fig. determine the forces in AB and
AC. Neglect the size of pulley.

Q18. A roller of weight 500 N is held in equilibrium on a smooth inclined plane by means of a rope as
shown in fig. Calculate the reaction force on the roller and tension in the rope.

Q19. Two identical bars PQ and RS, each weighing 50 N welded together to form a T and are suspended
in a vertical plane as shown in fig. calculate the value of angle θ that the bar PQ will make with vertical,
when a vertical force of 100 N is applied at S.

Q20. Four forces are acting tangentially on the circumference of a circle of radius 1m as shown in fig.
Find the magnitude and direction of the resultant and its location from the center of the circle.

4 Fundamental of Mechanical Engineering [BME-101/202]

You might also like