Scribd
Upload
54 views37 pages

BAlancing of Rotating Masses

Uploaded by

arasheedkhan902
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
54 views37 pages

BAlancing of Rotating Masses

Uploaded by

arasheedkhan902
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 37

Lecture_02

Balancing of Rotating Masses


Introduction
Why Balancing is Required ??
Balancing

OR
Balancing is the process of designing or modifying machinery so
that the unbalance is reduced to an acceptable level and if
possible is eliminated entirely.

Types:
• Balancing of rotating masses
• Balancing of reciprocating masses
Types of Balancing
Balancing of Rotating Masses
(Categories)
1. Balancing of a single rotating mass by a single mass rotating
in the same plane.

2. Balancing of a single rotating mass by two masses rotating in


different planes.

3. Balancing of different masses rotating in the same plane.

4. Balancing of different masses rotating in different planes.


Balancing of a Single Rotating Mass By a Single
Mass Rotating in the Same Plane
Consider a disturbing mass m1 attached to a shaft rotating at ω rad/s .
Let r1 be the radius of rotation of the mass m1.
centrifugal force exerted by the mass m1 on the shaft,
Balancing of a Single Rotating Mass By Two
Masses Rotating in Different Planes
Two balancing masses are placed in two different planes, parallel to the plane of
rotation of the disturbing mass, in such a way that they satisfy the following
two conditions of equilibrium.

1. The net dynamic force acting on the shaft is equal to zero. This requires that
the line of action of three centrifugal forces must be the same. This is the
condition for static balancing.

2. The net couple due to the dynamic forces acting on the shaft is equal to zero.
The algebraic sum of the moments about any point in the plane must be
zero.
1. When the plane of the disturbing mass lies in between the planes of the
two balancing masses
Consider a disturbing mass m lying in a plane A to be balanced by two rotating
masses m1 and m2 lying in two different planes L and M as shown in Fig. Let r, r1
and r2 be the radius of rotation of the masses in planes A, L and M respectively.
2. When the plane of the disturbing mass lies on one end of the planes of
the balancing masses
Balancing of Several Masses Rotating in the
Same Plane

Consider any number of masses (say four) of magnitude m1, m2, m3 and m4 at
distances of r1, r2, r3 and r4 from the axis of the rotating shaft. Let θ1, θ2,θ3 and
θ4 be the angles of these masses with the horizontal line OX, as shown in Fig.
Balancing of Several Masses Rotating in
Different Planes
For the Complete balance of the several revolving masses in different planes,
the following two conditions must be satisfied :
Methods of Balancing
Analytical method
1. Find out the centrifugal force (or the product of the mass and its radius of rotation)
exerted by each mass on the rotating shaft.
Graphical method
Example.1 (Static Balancing)
Example. 2 (Static Balancing)
Four masses m1, m2, m3 and m4 are 200 kg, 300 kg, 240 kg and 260 kg
respectively. The corresponding radii of rotation are 0.2 m, 0.15 m, 0.25 m and
0.3 m respectively and the angles between successive masses are 45°, 75° and
135°. Find the position and magnitude of the balance mass required, if its
radius of rotation is 0.2 m.

m1 = 200 kg ; m2 = 300 kg ; m3 = 240 kg ; m4 = 260 kg ;


r1 = 0.2 m ; r2 = 0.15 m ; r3 = 0.25 m ; r4 = 0.3 m ;
θ1 = 0° ; θ2 = 45° ; θ3 = 45° + 75° = 120° ;
θ4 = 45° + 75° + 135° = 255° ;
r = 0.2 m
1. Analytical Method
Example.1 (Dynamic Balancing)
A shaft carries four masses A, B, C and D of magnitude 200 kg, 300 kg, 400 kg and 200
kg respectively and revolving at radii 80 mm, 70 mm, 60 mm and 80 mm in planes
measured from A at 300 mm, 400 mm and 700 mm. The angles between the cranks
measured anticlockwise are A to B 45°, B to C 70° and C to D 120°. The balancing
masses are to be placed in planes X and Y. The distance between the planes A and X is
100 mm, between X and Y is 400 mm and between Y and D is 200 mm. If the balancing
masses revolve at a radius of 100 mm, find their magnitudes and angular positions.
Given : mA = 200 kg ; mB = 300 kg ; mC = 400 kg ;mD = 200 kg ,rA = 80 mmv= 0.08m ; rB =
70 mm = 0.07 m ; rC = 60 mm = 0.06 m ; rD = 80 mm = 0.08 m ; rX = rY = 100 mm = 0.1 m
Example. 2 (Dynamic Balancing)
a) Position of planes of masses
Choose a reference plane at ‘O’ so that the distance of the planes 1, 2, 3
and 4 from ‘O’ are L1, L2 , L3 and L4 respectively. The reference plane
chosen is plane ‘L’. Choose another plane ‘M’ between plane 3 and 4 as
shown.
Plane ‘M’ is at a distance of Lm from the reference plane ‘L’. The
distances of all the other planes to the left of ‘L’ may be taken as
negative( -ve) and to the right may be taken as positive (+ve).
The magnitude of the balancing masses mL and mM in planes L and M
may be obtained by following the steps given below.
Step 1:
Tabulate the given data as shown after drawing the sketches of position of
planes of masses and angular position of masses. The planes are tabulated
in the same order in which they occur from left to right
Example.3 (Dynamic Balancing)

A, B, C and D are four masses carried by a rotating shaft at radii 100, 125, 200
and 150 mm respectively. The planes in which the masses revolve are spaced
600 mm apart and the mass of B, C and D are 10 kg, 5 kg, and 4 kg
respectively. Find the required mass A and the relative angular settings of the
four masses so that the shaft shall be in complete balance.
Given : rA = 100 mm = 0.1 m ; rB = 125 mm = 0.125 m ; rC = 200 mm = 0.2 m ;
rD = 150 mm = 0.15 m ; mB = 10 kg ; mC = 5 kg ; mD = 4 kg
Example.4 (Dynamic Balancing)
Four masses A, B, C and D as shown below are to be completely balanced.

The planes containing masses B and C are 300 mm apart. The angle between planes
containing B and C is 90°. B and C make angles of 210° and 120° respectively with
D in the same sense. Find :
1. The magnitude and the angular position of mass A ; and
2. The position of planes A and D.
Given rA = 180 mm = 0.18 m ; mB = 30 kg ; rB = 240 mm = 0.24 m ; mC = 50 kg ;
rC = 120 mm = 0.12 m ; mD = 40 kg ; rD = 150 mm = 0.15 m ; ∠BOC = 90° ;
∠BOD = 210° ; ∠COD = 120°
Example. 5 (Dynamic Balancing)
A shaft is supported in bearings 1.8 m apart and projects 0.45 m beyond
bearings at each end. The shaft carries three pulleys one at each end and one
at the middle of its length. The mass of end pulleys is 48 kg and 20 kg and
their centre of gravity are 15 mm and 12.5 mm respectively from the shaft
axis. The centre pulley has a mass of 56 kg and its centre of gravity is 15 mm
from the shaft axis. If the pulleys are arranged so as to give static balance,
determine : 1. relative angular positions of the pulleys, and 2. dynamic forces
produced on the bearings when the shaft rotates at 300 r.p.m.
Given : mA = 48 kg ; mC = 20 kg ; rA = 15 mm = 0.015 m ; rC = 12.5 mm =
0.0125 m ; mB = 56 kg ; rB = 15 mm = 0.015 m ; N = 300 r.p.m. or ω= 2 π
× 300/60 = 31.42 rad/s

You might also like