www.makaut.

com
www.makaut.com

Name : …………………………………………….………………
Roll No. : …………………………………………...……………..
Invigilator’s Signature : ………………………………………..

CS/B.TECH (CSE)(N)/(IT)(N)/SEM-3/CS-301/2012-13

2012
ANALOG & DIGITAL ELECTRONICS
Time Allotted : 3 Hours Full Marks : 70

The figures in the margin indicate full marks.

Candidates are required to give their answers in their own words
as far as practicable.

GROUP – A
( Multiple Choice Type Questions )
1. Choose the correct alternatives for any ten of the following :
10 × 1 = 10
i) A 2-transistor class B power amplifier is commonly
called
a) push-pull b) dual
c) differential d) none of these.
ii) A stable multivibrator has
a) no stable state b) one stable state
c) two stable states d) none of these.
iii) Schmitt trigger circuit generates
a) triangular wave b) square wave
c) saw tooth wave d) none of these.
iv) A Wien-bridge oscillator has a frequency
1 1
a) b)
2π RC RC
1
c) d) none of these.
2π RC

3152(N) [ Turn over

www.makaut.com
 www.makaut.com
www.makaut.com

CS/B.TECH (CSE)(N)/(IT)(N)/SEM-3/CS-301/2012-13

v) Which of the following oscillators is used at audio

frequency ?
a) Crystal oscillator
b) Hartley oscillator
c) RC phase-shift oscillator
d) Colpitts oscillator.
vi) A + A′B + B ′ is equal to
a) A b) B′
c) 1 d) 0.
vii) Negative feedback in an amplifier is
a) reduced gain
b) increased noise
c) increased frequency & phase
d) reduced bandwidth.
viii) How many minimum NOR gates is required to
implement NAND gate ?
a) 3 b) 4
c) 5 d) 2.
ix) The digital logic family which has minimum power
dissipation is
a) TTL b) RTL
c) DTL d) CMOS.
x) If the input to T-flip-flop is 100 Hz signal, the final
output of the three T-flip-flops is cascade is
a) 1000 Hz b) 500 Hz
c) 300 Hz d) 12·5 Hz.
xi) Which one is the sequential circuit ?
a) Multiplexer b) Decoder
c) Encoder d) Counter.

3152(N) 2

www.makaut.com
 www.makaut.com
www.makaut.com

CS/B.TECH (CSE)(N)/(IT)(N)/SEM-3/CS-301/2012-13

xii) 8421 is a
a) weighted code b) non-weighted code
c) complementary code d) none of these.
GROUP – B
( Short Answer Type Questions )
Answer any three of the following 3 × 5 = 15
2. Implement Full-adder circuit using two Half-adders. Write
the truth table of Half-subtractor. 3+2
3. What is Multiplexer ? Why is it called 'data selector' ? Write
the important characteristics of digital IC. 2+1+2
4. Implement the function F ( A, B , C ) = ∑ m (1, 3, 5, 6 ) using
decoder. What is the difference between combinational
circuit and sequential circuit ? 3+2
5. Draw and explain the operation of Monostable multivibrator
using 555 Timer.
6. Draw and explain the Schmitt trigger circuit.
GROUP – C
( Long Answer Type Questions )
Answer any three of the following. 3 × 15 = 45
7. a) Write truth table, circuit diagram and timing diagram of
SR flip-flop using NOR gate.
b) Convert D flip-flop to JK flip-flop. 8+7
8. a) Design a 2-bit Asynchronous up counter using negative
edge trigger JK flip-flop and draw timing diagram.
b) Design a MOD-6 Synchronous counter using JK flip-
flop. 6+9
9. Write short notes on any three of the following : 3×5
a) Johnson counter
b) TTL family
c) Serial input parallel output shift register
d) BCD adder
e) 8 : 3 encoder.

3152(N) 3 [ Turn over

www.makaut.com
 www.makaut.com
www.makaut.com

CS/B.TECH (CSE)(N)/(IT)(N)/SEM-3/CS-301/2012-13

10. a) What are the advantages of negative feedback ?

b) Explain the operation of a phase shift oscillator with
circuit diagram.
c) Derive an expression for its frequency of oscillation.
3+6+6
11. a) Explain the working of a R-2R Ladder type DAC with a
neat circuit diagram.
b) Explain the working of a successive approximation
register (SAR) type ADC. 7+8
=============

3152(N) 4

www.makaut.com