Display User’s Manual

VistaLine & MedicLine

VL127D, VL157D, VL177D, VL197D, VL227D
VL221D
ML157D, ML177D, ML197D

www.olorin.com

Downloaded from www.Manualslib.com manuals search engine

 2

Downloaded from www.Manualslib.com manuals search engine

 Contents
1. Preface 4

2. Product features 5

3. Intended use of this product 6

4. Intended markets 6

5. Safety Precautions 7

6. Regulatory Tests and Certifications 10

7. Test of Medical Power adapter 11

8. FCC Information 11

9. Warranty and Limitation of Liability 12

10. Product identification 12

11. Cleaning of the Product 13

12. Disposal of the Product 13

13. Getting started 14

14. How to assemble Panel and Base unit 15

15. Mounting on a wall or LCD arm 16

16. Rotating the LCD Panel 17

17. Connection Method 18

18. Input signals 19

19. How to Operate 20

20. OSD Adjustment Functions 21

21. Marine & Touch technology information 24

22. Applicable Signal Timings 25

23. Specifications 26

24. Special Considerations for LCD Panels 38

25. Longer life for your monitor 40

26. Troubleshooting 41

27. Reference 42

27. Contact information 43

3

Downloaded from www.Manualslib.com manuals search engine

 Preface
Thank-you for purchasing this Olorin LCD Monitor.
To get the full benefit of the features that this product offers you, it is important that you read this
User’s Manual which, among other things, will explain how to properly install and operate the
monitor. In this user guide there are detailed product specifications, explanations for many of
the technical terms used in this manual as well as information on regulatory approvals, cleaning,
service instructions, warranty terms, waste disposal and some other useful information.

It is of utmost importance that you carefully read and follow the safety instructions and
safety notices included in this User´s Manual.

Failure to comply with these instructions could in some instances cause bodily harm to yourself
or other persons and/or un-repairable damage to the product or to other attached devices /
appliances.

Throughout this manual the following symbols are used to guide you to the proper use of the
product:

Symbols Person or properties could be

at risk of injury or damage.
Expresses DO NOT.
Caution

Expresses MUST DO.

Person could be at risk of
severe injury or death.

Warning

Keep this Users Manual in an easy accessible and safe place for future reading of it. If you lose
your copy, you may request a new one by contacting us at our internet home page www.olorin.
com.

Olorin reserves the right to change the specifications of this product without any notice. Such
changes could cause the operation of the product to be slightly different from the descriptions in
this copy of the Users Manual.

Windows and MS-DOS are trademarks and/or registered trademarks of Microsoft Corporation in
the United States and/or other countries. VESA is a trademark of the Video Electronics Standard
Corporation. All other product and company names are trademarks of their respective owners.

Copyright © 2012

Downloaded from www.Manualslib.com manuals search engine

 Product Features
Standard delivery
The product is normally delivered in 2 main parts, which, when mounted together, form a normal
monitor for desktop use.

• a LCD panel with TFT picture element which also contains the lamps for the backlight along
with necessary electronics and cable connectors as well as power connector. These parts are
mounted inside a plastic housing.
• a base unit (stand) to be mounted at the VESA holes at the back of the panel.

For certain applications, when the monitor is to be placed on a wall or built into a desk, then only
the LCD panel part is delivered. In these cases it is quite often delivered with the plastic housing
removed in what is called “open frame”. Certain other options or special mounting components
might have been pre-installed.

When the monitor has been delivered as open frame there is a greater risk to come
in contact with electric parts which could cause harm to yourself or your property. It
should therefore only be handled with special precaution and only by properly trained
Warning service personnel.

Power management
This unit has power management system. The monitor will go into “sleep mode”, where power
consumption is less than 5W, whenever either horizontal or vertical signals or both disappear.

High performance panel element

The color LCD panel used in this product is specifically designed for advanced applications such
as video, marine dimming and viewing digital X-ray images. ALC (Automatic Luminance Control)
circuits will automatically adjust for the decay of the backlight lamps.

Protective glass for ML157D, ML177D & ML197D (IPX)

The medical versions of the product are fitted with a protective glass for easy cleaning.

Preloaded DICOM curve

The monitor has a preloaded Barten DICOM curve for use as a plug-n-play X-ray review display.

Ergonomic features
To ease eyestrain on the user, the panel features excellent viewing angles. In addition, the base
unit can be adjusted to fit the individual user’s need by adjusting the height and tilt of the monitor.

VESA® standard wall / arm mountings

The unit is compliant with VESA’s 100mm-pitch (75 mm for 12” and 15” monitors) for hanging
tools. The base unit is detachable; the panel can be mounted on a wall or arm according to user’s
enviroment.

Downloaded from www.Manualslib.com manuals search engine

 Intended use of this product
This product has been designed and developed for use as a visual output device for direct
connection to a Personal Computer and PC compatible devices as well as other video generating
equipment, such as cameras. The product will accept industry standard video signals coming over
cables with industry standard type connectors. The product will operate and function properly in
normal office environment and under conditions as specified in the Product Specification chapter.

Attempting to use the product for any other purpose than its intended use or
connecting to other devices could cause damage to the product and / or to other
property and equipment. There could also be a risk of bodily harm to yourself or other
Warning persons.

The product operates on 12V (some on 24V) DC power and must be connected thru the AC 100-
240V, 50-60Hz to12V DC adapter (or 24V DC adapter) which is included with the product. Power
to the adapter should be coming from an ordinary grounded AC 100-240V power outlet.

Never try to connect the product to any other power source than the 12V/24V adapter
delivered together with the product. There would be a risk of electrical shock which
could cause bodily harm, possibly even death. Most certainly such electrical shock will
Warning damage the product.

The product can also be delivered with certain options installed. Such options could be touch
panel or other special accessories.

All other uses of the product, including but not limited to attempts such as;

• connection to other types of power sources

Warning
• using other types of mounting or placement of the product

• connection to other devices than those for which the monitor has been
designed.

will void any and all warranties of the product and the manufacturer will not be
responsible or libel for any bodily injury or property damage either directly or
indirectly caused by such non-intended use of the product.

Intended Markets
Olorin products are developed primarily for sales and installation in countries within Europe and
North America. The products comply with all regulations and directives issued by the European
Union and by authorities in the United States.

The products are not intended for sales and/or installation in countries, which require
other or additional mandatory approvals than those required by the authorities of the
Warning European Union or the United States.

Consult the product identification label or product specification for regulatory approvals that apply
to this product.
6

Downloaded from www.Manualslib.com manuals search engine

 Safety Precautions
It is important that you read through the following notes of Safety Precautions to avoid any
damage to the Product, yourself or other property. Following these precautions will also ensure
that you get the best use of the Product.

DO NOT OPEN THE PRODUCT. There are no user serviceable parts inside. Because
of high voltage inside there is a risk of bodily injury or death. Only authorized and
qualified service personnel should maintain the product.
Warning

Cautions when setting up

Do not put the unit on unstable places (on a wonky table or in an inclined
place), which might cause injuries if it falls down.

Caution

Do not place the unit where it is subject to direct sunlight or near any
heating device. This could cause overheating resulting in damage to
the product and eventually causing a fire.
Caution

Cautions when using

Do not put the unit in such a place where there is bad air circulation,
dust, humidity, oily smoke or steam. It may lead to a fire.

Warning

Do not put any metal materials or flammable foreign objects into the
unit through the vent holes. It may lead to electric shock and/or fire.
Immediately disconnect the unit from the power outlet and contact your
Caution local re-seller for service.

Scratching or hitting with hard objects may damage the unit.

Caution

Downloaded from www.Manualslib.com manuals search engine

 Safety Precautions
Do not use the unit turned over on its back, put on its side, or upside
down. These positions may cause the heat that the unit generates to
accumulate inside the unit. Such overheating can cause damage to the
Warning product and eventually start a fire.

When using the unit for several hours, you should take a 10-15 minute
break every hour to reduce eyestrain. Failure to do so could cause injury to
your eyes.
Caution

Abnormal circumstances
In case of any abnormality such as odor, sound, and overheat taking
place, immediately turn off the power and disconnect the plug from
the outlet. Continuing to use the unit under such condition may lead to
Warning electric shock and/or fire. For assistance contact your local re-seller.

In the event of thunder, immediately turn off the power and

disconnect the plug from the outlet. Lightning strikes may cause
electric shock and/or fire.
Warning

In the event of broken panel and leaking liquid crystal, do not inhale,
swallow, or touch the liquid crystal. It may cause you to get poisoned
and/or having a skin irritation. If you put it in your mouth, immediately
Warning gargle with water and contact a doctor to get a checkup. In case of
getting it on your skin and/or cloth, wipe it off with alcohol and rinse
them.

Downloaded from www.Manualslib.com manuals search engine

 Safety Precautions
Maintenance
Do not remove the plastic cabinet. There are high voltage parts inside
that may lead to electric shock. Ask a re-seller for adjustment and
inspection.
Warning

Do not remodel or repair. It may lead to fire, electric shock, or injuries.

Warning

Clean the dust inside the display once a year. The dust that accumulates
inside the unit may lead to fire. Ask a re-seller for adjustments and
inspection.
Caution

Disconnect the plug from the outlet when you do not use the unit for a
prolonged period.

Caution

Downloaded from www.Manualslib.com manuals search engine

 Regulatory Tests and Certifications
All Olorin products have normally been tested to comply with all mandatory Regulatory
requirements for the markets where the products are sold. Approvals are listed by each
Regulatory Agency under the name of the manufacturer and model number as specified on the
Product Identification Label. Copies of such approvals can be requested by contacting Olorin AB
via www.olorin.com.

Approvals applicable for this product is listed in the Product Specification section of this
manual.

Tests and Approvals for VistaLine Series

Each product in the VistaLine series has been tested as an IT-category product for normal office
environment and for use as a desktop monitor. They comply with the following standards and
regulations:

• CE for use within the European Union member states

• UL for use in the United States
• FCC for use in the United States
• WEEE for use within the European Union member states
• RoHS for use within the European Union member states

Tests and Approvals for MedicLine Series

Each product in the MedicLine series has additionally been tested for risk of electrical shock and
to comply with

• MDD directive 93/42/EEC class 1 for the European Union member states
• EN60601-1, EN60601-1-2
• IEC 60601-1
Some of the products have also been tested to comply with:
• UL 60601-1
• CAN/CSA C22-2 No. 601-1

Under these directives and regulations, MedicLine products are complying with the requirements
for a Class 1 product with continuous mode of operation. The monitor must not be in direct contact
with a patient.

Using any other 12V/24V adapter than the medical approved one delivered with the
product or connecting this to a non-grounded power outlet voids the approval.
Warning

Before taking the product in use, the person installing it must test that the grounding
of the monitor complies with the impedance requirements of the country where it is
being installed.
Warning

When using at 240 V in the United States, supply must be from center-tapped, 240 V,
single phase circuit.
Warning
10

Downloaded from www.Manualslib.com manuals search engine

 Test of medical power adapter
The power supply is Class I. Protective earthed parts are only located inside the power supply
enclosure and therefore are not accessible. The accessible parts of the enclosure and output
are DOUBLE INSULATED from all mains voltage electrical parts. Ground continuality test is not
relevant.

Leakage test of the adapter is made by having the measurement equipment connected to the AC
plug, no need to open the plastic enclosure.

FCC Information
FCC (U.S. Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause unacceptable interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult your re-seller or an experienced radio/TV technician for help.

FCC Warning:
To assure continued FCC compliance, the user must use a grounded power supply cord and the
provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized changes
or modifications to this monitor would void the user’s authority to operate this device.

11

Downloaded from www.Manualslib.com manuals search engine

 Warranty and Limitation of Liability
Warranty
For details of the warranty please see the separate warranty document included with this product.

Limitation of Liability
Olorin AB, including any of its affiliates, manufacturing partners and sales agents, is not liable for
any claim for damages including, but not limited to, loss of business profits, disruption of business,
change or loss of saved data, when damage is arising from

• fire, earthquakes, actions taken by any third party, any other accidents, intentionally
or negligently, improper use of the product by the user, or any use under other abnormal
circumstances,
• the use or inability to use this product,
• the use for other purposes than the intended use as described in this document
• malfunctions caused by the combination of connected devices

Product identification
Affixed to the panel part of the product is a Product Identification Label. It is normally affixed in the
connector compartment. This label contains the following information:

• Olorin logo and web address

• Product Family name (example: Olorin VistaLine VC190D)
• Manufacturers product number
• Part number
• Serial Number
• Power information
• Symbols for Regulatory approvals
• WEEE symbol for disposal of the product
• Manufacturers name
• Country of Origin

12

Downloaded from www.Manualslib.com manuals search engine

 Cleaning of the Product
Be careful when cleaning the plastic housing of the panel so that no liquid or other
objects will drip down into the product through the ventilation holes. This could cause
electric shock and damage the product.
Caution

Normal dust and lint particles can be easily wiped off with a soft cloth tissue.

For grease or dirt that is more firmly fixed to the product, the use of a soft and dry micro fiber
based cloth tissue will normally remove it all.

You can also use a mild liquid detergent mixed with water for cleaning together with a soft cloth
tissue. This will clean both the cabinet and the LCD panel well. For the LCD panel you can also
use isopropyl alcohol based liquids (without abrasive) or non-ammoniac glass cleaner.

When cleaning the LCD panel you will get the best result if you clean the panel when its surface
has cooled down to normal room temperature. On a warm panel the liquid evaporates too quickly
leaving traces of the cleaning. Afterwards wipe the surface dry with another soft cloth tissue.

When cleaning the cabinet do NOT use thinner, benzene or alcohol as these might
damage the plastic and cause the paint to peel off. Do NOT use organic solvent such
as acetone and toluene when cleaning the panel.
Warning

If you use any liquid for cleaning you must first un-plug the power to the monitor and
not connect it again until you are certain that all the liquid particles have evaporated.
Failure to do so could result in electric shock.
Warning

Do not use any tools with hard or sharp material for cleaning. The panel can very
easily be scratched or damaged from such tools.
Caution

Do not press hard on the panel when cleaning. This could cause damage to the LCD
panel element.
Caution

Disposal of the Product

Do not dispose of the unit with general wastes.

The monitor has been manufactured to comply with the EU directive on RoHS (Reduction of
Harmful Substances) but even so the LCD panel contains a small amount of mercury and the
monitor should therefore be disposed of according to local laws. Please get information from your
local re-seller how collection is handled in your country. For countries that are members of the EU
the WEEE directive applies and proper marking is on the product label affixed to the monitor.

13

Downloaded from www.Manualslib.com manuals search engine

 Getting started
Before operating this monitor, please make sure that all items listed below are present in your
delivery.

Standard Items
• The LCD monitor panel
• User’s manual
• Warranty booklet
• AC/DC adapter
• AC Power cord
• DVI to DVI cable
• DVI to VGA cable
• 3,5 mm Audio cable

Optional Items
• The Base unit with 4 Screws and Screwdriver
• S-video cable
• DVI to VGA & DVI splitter cable

Optional Items (for Touch panel)

• USB cable
• Serial (RS-232) cable
• CD-ROM with Touch panel drivers

If any of the above items are found missing or if you wish to order the optional items, please
contact your reseller.

14

Downloaded from www.Manualslib.com manuals search engine

 How to assemble Panel and Base unit
The product normally comes in 2 cartons and you need to assemble the panel and the base unit.
A screwdriver and proper screws are included in the box for the base unit.

1. Remove the back of the base unit by grabbing it firmly at the top and pulling it up and
backwards.

2. Place the monitor with the front down on a level surface. Make sure that there are no objects
on the surface that could damage the panel element. It should be placed so that the OSD
wheel is at the lower left corner seen from yourself.

Place the metal plate onto the VESA mounting cut-out on the back of the panel. Hold the
bottom of the base unit towards yourself.

Test that you can swing the base unit to the left so that swivel between Landscape and
Portrait will be correct.

3. Locate the holes in the back of the base unit through which you can stick the screwdriver to
reach and put the 4 screws in place.

4. Remount the back cover.

If you mount any device using these 4 holes on the back of the panel you must not
use use screws longer than 10 mm. Longer screws will cause damage which is not
covered by the product warranty.
Caution

15

Downloaded from www.Manualslib.com manuals search engine

 Mounting on a wall or LCD arm
The Monitor has Video Electronics Standards Association (VESA) standard mounting holes
tapped into the rear panel. The standard holes are M4 set 100 mm (for 17” and larger monitors) or
75 mm (12” and 15” monitors) apart.

If you intend to mount the monitor on the wall, we strongly recommend that you use wall mount
kits with attached M4*10mm screws and which can hold a load of more than the weight of the
monitor. Ensure it is securely and safely installed.

If you mount any device using these 4 holes on the back of the panel you must not
use use screws longer than 10 mm. Longer screws will cause damage which is not
covered by the product warranty.
Warning

The position of the connectors can vary between models and they may or may not be covered
with a flap.

16

Downloaded from www.Manualslib.com manuals search engine

 4
Rotating the LCD Panel
When setting the LCD display to vertical display (portrait orientation), lift the LCD panel to the top
of the base unit as shown in the figure below and rotate it by 90 degrees.

Procedure
1. Tilt the LCD panel upward.(Perform this procedure before sliding the panel upward.)

2. Lift the LCD panel to the top.

3. Rotate the LCD panel by 90 degrees.

4. Reposition the LCD panel to the bottom while in the vertical position (portrait orientation).

ded.

Display in portrait orientation

Pivot® software or graphics card that enables portrait orientation is necessary.

ook

17

Downloaded from www.Manualslib.com manuals search engine

 Connection Method
No tools are required to connect the LCD monitor to your PC or other device. Simply follow the
instructions outlined in the next few pages.

Connectors for the signal cables and power are located on the back of the panel behind the cover
lid. Please refer to the diagram on the next page for the connector configuration.

Connect Power Adapter and Cable

Connect the round shape plug end of the AC/DC adapter to the DC Power input connector of the
LCD monitor. Connect the female end of the power cable to the AC power input receptacle on the
AC/DC adapter. Then, plug the male end of the power cable into an grounded AC outlet.

Make sure you use the AC to DC adapter delivered with the product.

Caution

Connect Signal cable

On next page you can see which input connectors there are available on your monitor and which
cable you should connect depends on your source for the input signal.

VGA, DVI, HDMI or Displayport output from a PC

If your source is VGA (analog) then use either a VGA to VGA cable for connection to the VGA
connector or a VGA to DVI-I cable for connection to the DVI-I connector on the monitor.

If your source is DVI (digital) then use the DVI-DVI cable supplied with the monitor and connect to
the DVI-I connector on the monitor.

If your source is HDMI or Display-Port then you need a converter from HDMI or Display-Port to
DVI. Then you connect the DVI-DVI cable between the DVI-I connector on the monitor and the
converter. There are also available HDMI or Display-Port to DVI cables that can purchased from
your local reseller.

Video input from camera or other NTSC/PAL signal generating equipment

Use S-video cable or for Composite video, BNC cables.

Connect Audio Cable

Connect an audio output device to the monitor with the included stereo mini cable, using the 9mm
audio jack.

RJ45 Connector
If you want to control the On/Off and OSD at a distance from the monitor there is an optional
external control box available. This box is connected with an RJ45 cable.

When you disconnect the cord /cables, be sure to hold the connector and not the
cable itself. Also make sure you use cables and connectors of high quality.

Caution

18

Downloaded from www.Manualslib.com manuals search engine

 Input signals
15”, 17” and 22” *1

19” Connections (RJ45 connector placed at bottom of panel)

DVI-I to DVI-D & VGA splitter cable

*1
On 22” monitors, RJ45 is located on the opposite side of the backet, next to Audio.

19

Downloaded from www.Manualslib.com manuals search engine

 How to Operate

Control Dial
The Control Dial is a multi-functional device located behind the LED Indicator on the right side of
the front bezel. It has three movements-rotate upward, rotate downward and press inward as a
button.

1. Power On/Off
Press the Control Dial to power the unit on from the off stage (the display is off). To turn the
power off, press the Control Dial and hold for at least 1 second until the display turns off.

2. OSD Control
While the monitor is on (image on the screen), pressing on the Control Dial activates the
OSD. While the OSD menu is active, use the three way movements of the Control Dial to
adjust the monitor.

Rotate Downward: Move Up/Right, Increase, Larger, More

Rotate Upward: Move Down/Left, Decrease, Smaller, Less
Button Press: Execute, Do, Save

3. Change of Brightness Setting

If you rotate the Control Dial without first having clicked to enter the OSD, then it will change
the brightness setting. It will do so in a quick way by adjusting with larger steps in the bright
area and gradually lower values towards the dark area. This is to facility quick change of
brightness when you have the “Dimming option” installed.

LED Indicator
This LED indicator turns green when the power is switched ON and the power cord is properly
attached. It turns amber when the monitor goes into a power saving mode (Active Off). On some
models it will be switched off entirely after 10 minutes to avoid that the lamp will distract your
vision.

20

Downloaded from www.Manualslib.com manuals search engine

 OSD Adjustment Functions
PreVu™ On-Screen Display
The LCD monitor features a PreVu™ On-Screen Display(OSD) menu with easily identifiable icons
designed to make adjusting your monitor display settings a more user-friendly process. When
highlighted, the icon illustrates the control function and a brief instruction to assist the user in
identifying which control needs adjustment.

The OSD menu is activated by pressing the Control Dial inward and you can select and adjust
the function of your choice by rotating and clicking the Control Dial. The main menu displays a
list of control icons and the current video input mode. Rotate the dial to move the highlights to
the control you would like to adjust, then press the Control Dial inward to select that control or
to activate that function. Depending on the control you selected, a submenu of the control with a
status bar will appear. The status bar indicates in which direction, from the factory preset, your
adjustments are being made. Rotate the Control Dial to adjust the control.

When you have finished making the adjustments, the setting is saved automatically by exiting
the control function. If you do not touch the control dial for 20 seconds, the OSD is automatically
exited saving your current settings.

Menu descriptions
The LCD monitor is capable of accepting DVI-I VGA, DVI-I DVI, S-Video and Composite/BNC
signal inputs and therefore has three different sets of OSD control functions.

Depending on your input source and also depending on which color mode you have selected
there are some functions that are not necessary, cannot be executed or are locked out to comply
with certain standards. You will then encounter the message “Not Available” when you try to select
such functions.

The following charts show the function tree and brief explanations of the functions.

21

Downloaded from www.Manualslib.com manuals search engine

 Charts of OSD Adjustment Functions

When you enter the OSD you first come to the menu for selection of input so, if you have 2
sources connected (i.e. PC and camera) you can quickly switch from one source to the other.
When you click on another source you will leave the OSD system. If you want to proceed to the
regular Main Menu you must choose “MAIN MENU”.

Source selection
• DVI-I VGA Selects VGA
• DVI-I DVI Selects DVI
• VIDEO S-video Selects S-video
• VIDEO BNC Selects Composite video
• MAIN MENU Continue to Main Menu

Main menu
Exit Exit OSD Menu, in sub menus ’Exit’ will move you up in the tree structure.

Auto setup *1 Adjust monitor to analog signal from graphics card.

Image OK? If you answer YES then you will exit the menu. If you answer NO, proceed to Clock /
Phase menu.

Brightness Adjust brightness level. See also special note on brightness adjustment in special
situations.

Contrast Adjust contrast of the monitor. Not active when Clear base Barten color mode has
been selected.

Display *1

H. Position Adjust horizontal screen position.

V. Position Adjust vertical screen position.

Hue *2 Adjust the hue of the color settings.

Color mode

Cool Select a cold color temperature of about 9000K.

Neutral Select a neutral color temperature of about 6500K.

Warm Select a warm color temperature of about 5500K.

User In a separate sub-menu you can set individual values for Red, Green and Blue.

Clear base Barten A special color mode intended for viewing of X-ray pictures. Has a preset greyscale
curve in accordance with the DICOM standard. Automatically sets the monitor to
brightness of about 170 candela and color temperature of about 6500K. When set to
this mode the OSD functions for Brightness, Contrast, Black Level are in-activated. It
also locks ALC to ON.

Clock/phase *1

Clock Fine tune video signal for positioning of the picture horizontally on the screen.

Phase Adjust Phase frequency to control flickering or horizontal waves on the screen.

Saturation *2 Adjust the saturation of the color settings.

Black level Adjust the offset level for black color, inactive when Clear Base Barten color mode is
selected.

22

Downloaded from www.Manualslib.com manuals search engine

 Charts of OSD Adjustment Functions

Main menu continued

Management

Scaling Scaling of the input signal

Full Displays the image on the full screen

1:1 Will display the input without any scaling. For instance a resolution of 640x480
will be displayed over the corresponding number of pixels in the center of the
screen.

4:3 Will scale the picture to 4:3 format.

5:4 Will scale the picture to 5:4 format.

16:9 Will scale the picture to 16:9 format.

16:10 Will scale the picture to 16:10 format.

OSD Display Positioning of the OSD on the display.

H. Position Move position of the OSD display horizontally.

V. Position Move position of the OSD display vertically.

Language Select language for OSD. Returns to Main Menu and will from then on show
the OSD in the selected language. You can choose between English, French,
German, Italian, Spanish or Japanese.

Key lock A function with which you can lock the OSD menu to settings you have made.
When you then try to enter into the OSD you will stop at source menu. To enter
into this function you must click on the OSD wheel 3 times within 2 seconds.
You also do the same when you want to un-lock the Key Lock.

Bright bar Special setting used to select if the setting bar for Brightness adjustment shall
be shown on the monitor or not. Active only for when you adjust the brightness
by turning the control wheel without having entered the OSD menu. You select
YES or NO if it should be shown or not.

ALC Automatic Luminance Control (ALC) is a function which can be set to ON or

OFF. When set to ON it will automatically increase the Brightness setting to
off-set the wear on the backlight lamps. It has been developed mainly for when
you select Clear base Barten color mode and is always ON in that mode. It will
make the monitor to better comply with the DICOM requirements during the
full life of the product and not only at the time of delivery. In other color modes
you can set it to ON or OFF but since you have the ability to manually adjust
brightness in these color modes the recommendation is to set it to OFF.

Recall If you execute Recall the monitor will be reset to values that are default values
at time of delivery.

Mute You can set this to ON or OFF and the function is to switch off the speaker
sound.

Volume You can adjust the sound volume from the built in speakers.

Monitor info This will show some information of the monitor which are useful for service. The
information contains the following: Model number, Firmware version, Operating
Hours, ALC check, Dimming check, Resolution and Color mode.

*1 Only available if the monitor input source is VGA

*2 Only available if the monitor input source is S-video or BNC.

23

Downloaded from www.Manualslib.com manuals search engine

 Marine functionality
The following features are optional.

Dimming
To lower the brightness to minimum on a monitor without sacrificing contrast values. This is
especially useful on ships during night use in order to keep night vision intact.

Sunlight readable
Polarizing filter that is applied on top of the LCD display, increases color saturation and decreases
reflections on the panel in environments where strong sunlight is common.

Touch technologies
The following features are optional.

Surface Acoustic Wave (SAW)

Surface acoustic wave (SAW) technology uses ultrasonic waves that pass over the touchscreen
panel. When the panel is touched, a portion of the wave is absorbed. This change in the ultrasonic
waves registers the position of the touch event.

Projected Capacitive Touch (PCAP)

Projected Capacitive Touch (PCAP) are made up of a matrix of rows and columns of conductive
material, layered on sheets of glass. Voltage applied to this grid creates a uniform electrostatic
field, which can be measured. When a conductive object, such as a finger, comes into contact
with a PCAP panel, it distorts the local electrostatic field at that point.This is measurable as a
change in capacitance. If a finger bridges the gap between two of the ”tracks,” the charge field is
further interrupted and detected by the controller. The capacitance can be changed and measured
at every individual point on the grid (intersection). Therefore, this system is able to accurately
track touches. Due to the top layer of a PCAP being glass, it is a more robust solution than less
costly resistive touch technology. It is possible for a PCAP system to sense a passive stylus or
gloved fingers.

24

Downloaded from www.Manualslib.com manuals search engine

 Applicable Signal Timings
The display may not work correctly with timings other than listed below.
◎ : Recommended timing ○ : Applied timing ∆ : Pseudo-display timing Int : Interlaced display

Resolution Frequency
Display mode Horizontal Vertical 12" 15" 17" 19" 22"
Horizontal Vertical
(kHz) (Hz)
720 400 31.5 70 ○ ○ ○ ○
VGA
640 480 31.5 60 ○ ○ ○ ○ ○

640 480 37.9 72 ○ ○ ○ ○ ○

640 480 37.5 75 ○ ○ ○ ○ ○

800 600 35.1 56 ○ ○ ○ ○ ○

800 600 37.9 60 ○ ○ ○ ○ ○

800 600 48.1 72 ○ ○ ○ ○ ○

800 600 46.9 75 ○ ○ ○ ○ ○

1024 768 48.4 60 ◎ ◎ ○ ○ ○

1024 768 56.5 70 ○ ○ ○ ○ ○

1024 768 60.0 75 ○ ○ ○ ○ ○

1280 1024 64.0 60 ∆ ∆ ◎ ◎ ○

VESA
1280 1024 80.0 75 ∆ ∆ ○ ○ ○

1600 1200 75.0 60 ∆ ∆ ○

848 480 75 / 60 ○

1280 720 75 / 60 ○

1600 900 60 ○

1920 1080 60 ◎

480p 60 / 50 ○

720p 60 / 50 ○

1080i 60 / 50 ○

1080p 60 / 50 ○

640 480 35.0 67 ○ ○ ○ ○ ○

MAC 832 624 49.7 75 ○ ○ ○ ○ ○

1024 768 60.2 75 ○ ○ ○ ○ ○

Video NTSC 15.73 60 Int. Int. Int. Int. Int.

Input PAL 15.63 50 Int. Int. Int. Int. Int.

The display mode ∆ is a downscaled Pseudo-display.

Caution

25

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL127D
Display Screen size, Format 12,1”, 4:3

Brightness, candela/m2 450 cd/m2

Contrast 700:1

Resolution, Megapixel 1024x768

Response time 25 ms (Full cycle)

Viewing angles, H/V 160 / 160

Color depth 262K / 16,2M

Panel type TN

Backlight type CCFL

Environmental Operating Storage

Temperature, Celcius 10~40°C -20~60°C

Humidity (non-condensation) 30~75% 10~90%

Air pressure 700~1060hPa 500~1060hPa

Input signal Connections (1) DVI-I (29-pin) connector:Compliant with DVI 1.0
(2) S-video connector: Color signal:0.286Vp-p/75 Ω Brightness
signal:1Vp-p/75 Ω
(3) BNC connector: Composite signal:1Vp-p/75 Ω
(4) Audio signal (pin jack3.5mm) connector:0.2-2.0 Vrms
(5) RJ 45 connector: Extended interface (OSD control)

Power Power supply Ext. Adapter 12v

Power consumption Approx. 20W Max. / Less than 2.5W in stand-by mode

Functionality Automatic adjustment Yes (via OSD)

OSD for settings PreVu™

Speakers No

Luminance compensation ALC

Pivot Yes, software required.

Protective glass No

Touch panel No

Dimming Optional

Sunlight Readable Optional

DICOM pt. 14 preset No

International standards Medical certificates No

IT certificates No

Warranty Replacement warranty Two (2) years

26

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL127D
Appearance Net. weight 1,8kg

Measurements (WxDxH) 262 x 45 x 222 mm

Product color Metallic

Open frame Yes

Mounting Kensington lock No

VESA standard 75 mm

262 mm 45 mm
222 mm

27

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL157D & ML157D
Display Screen size, Format 15” (304 x 228 mm), 4:3

Brightness, candela/m2 250 cd/m2 (typical value)

Contrast 700:1 (typical value)

Resolution, Megapixel 1024x768 0,8 Mpix

Response time 8 ms (Full cycle)

Viewing angles, H/V 160 / 150 (typical value at CR 10:1)

Color depth 262K / 16,2M

Panel type TN

Backlight type CCFL

Environmental Operating Storage

Temperature, Celcius 10~40°C -20~60°C

Humidity (non-condensation) 30~75% 10~90%

Air pressure 700~1060hPa 500~1060hPa

Input signal Connections (1) DVI-I (29-pin) connector: Compliant with DVI 1.0
(2) S-video connector: Color signal:0.286Vp-p/75 Ω Brightness
signal:1Vp-p/75 Ω
(3) BNC connector: Composite signal:1Vp-p/75 Ω
(4) Audio signal (pin jack3.5mm) connector:0.2-2.0 Vrms
(5) RJ 45 connector: Extend interface (OSD control)

Power Power supply 12Vdc, 5A

Power consumption Approx. 35W Max. / Less than 4.5W in stand-by mode

Functionality Automatic adjustment Yes, via OSD.

OSD for settings PreVu™

Speakers Yes

Luminance compensation ALC

Pivot Yes, software required.

Protective glass VL157D: Optional, ML157D: Yes

Touch panel Optional, Surface Wave Touch (SAW) USB or RS-232

Dimming Optional

Sunlight Readable Optional, 550 cd/m2

DICOM pt. 14 preset Clearbase Barten

International standards Medical certificates, *1 IEC60601-1, EN60601-1, EN60601-1-2,

IT certificates UL/cUL, FCC-B, CE, WEEE, RoHS

Warranty Replacement warranty Two (2) years

28

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL157D & ML157D
Appearance Net. weight Approx. 3.3 kg (w/o base) 5.4 kg (w/ base)

Measurements (WxDxH) 375 x 59 x 282 mm (w/o base) *2

375 x 201 x 358 mm (w/ base)

Product color Graphite grey or white

Open frame Optional

Base unit Height adjustable No

Tilting and swivel Yes

Mounting Kensington lock Yes, prepared

VESA standard 75 mm

59

*1 Only applies to ML157D.

*2 Units with Protective glass (ML157D) or Touch panel are 63 mm deep.

29

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL177D & ML177D
Display Screen size, Format 17” (337 x 270 mm), 5:4

Brightness, candela/m2 350 cd/m2 (typical value)

Contrast 1000:1 (typical value)

Resolution, Megapixel 1280x1024 1,3 Mpix

Response time 5 ms (Full cycle)

Viewing angles, H/V 160 / 150 (typical value at CR 10:1)

Color depth 262K / 16,7M

Panel type TN

Backlight type CCFL

Environmental Operating Storage

Temperature, Celcius 10~40°C -20~60°C

Humidity (non-condensation) 30~75% 10~90%

Air pressure 700~1060hPa 500~1060hPa

Input signal Connections (1) DVI-I (29-pin) connector: Compliant with DVI 1.0
(2) S-video connector: Color signal:0.286Vp-p/75 Ω Brightness
signal:1Vp-p/75 Ω
(3) BNC connector: Composite signal:1Vp-p/75 Ω
(4) Audio signal (pin jack3.5mm) connector:0.2-2.0 Vrms
(5) RJ 45 connector: Extend interface (OSD control)

Power Power supply 12Vdc, 5A

Power consumption Approx. 50W Max. / Less than 4.5W in stand-by mode

Functionality Automatic adjustment Yes, via OSD.

OSD for settings PreVu™

Speakers Yes

Luminance compensation ALC

Pivot Yes, software required.

Protective glass VL177D: Optional, ML177D: Yes

Touch panel Optional, Surface Wave Touch (SAW) USB and RS-232

Dimming Optional

Sunlight Readable Optional

DICOM pt. 14 preset Clearbase Barten

International standards Medical certificates, *1 IEC60601-1, EN60601-1, EN60601-1-2

IT certificates UL/cUL, FCC-B, CE, WEEE, RoHS

Warranty Replacement warranty Two (2) years

30

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL177D & ML177D
Appearance Net. weight Approx. 5.5 kg (w/o stand) 7.5 kg (w/ base)

Measurements (WxDxH) 378mm x 70mm x 314mm (w/o base)

378mm x 201mm x 372mm (w/ base)

Product color Graphite grey or white

Open frame Optional

Base unit Height adjustable No

Tilting and swivel Yes

Mounting Kensington lock Yes, prepared

VESA standard 100 mm

*1 Only applies to ML177D.

31

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL197D & ML197D
Display Screen size, Format 19” (376 x 301 mm), 5:4

Brightness, candela/m2 300 cd/m2 (typical value)

Contrast 1000:1 (typical value)

Resolution, Megapixel 1280x1024 1,3 Mpix

Response time 20 ms (Full cycle)

Viewing angles, H/V 178 / 178 (typical value at CR 10:1)

Color depth 16,7M

Panel type MVA

Backlight type CCFL

Environmental Operating Storage

Temperature, Celcius 10~40°C -20~60°C

Humidity (non-condensation) 30~75% 10~90%

Air pressure 700~1060hPa 500~1060hPa

Input signal Connections (1) DVI-I (29-pin) connector:Compliant with DVI 1.0
(2) S-video connector: Color signal:0.286Vp-p/75 Ω Brightness
signal:1Vp-p/75 Ω
(3) BNC connector: Composite signal:1Vp-p/75 Ω
(4) Audio signal (pin jack3.5mm) connector:0.2-2.0 Vrms
(5) RJ 45 connector: Extended interface (OSD control)

Power Power supply 12Vdc, 5A

Power consumption Approx. 55W Max. / Less than 4.5W in stand-by mode

Functionality Automatic adjustment Yes, via OSD.

OSD for settings PreVu™

Speakers Yes

Luminance compensation ALC

Pivot Yes, software required.

Protective glass VL197D: Optional, ML197D: Yes

Touch panel Optional, Surface Wave Touch (SAW) SAW USB and RS-232

Dimming Optional

Sunlight Readable Optional

DICOM pt. 14 preset Clearbase Barten

International standards Medical certificates *1 IEC60601-1, EN60601-1, EN60601-1-2

IT certificates UL/cUL, FCC-B, CE, WEEE, RoHS

Warranty Replacement warranty Two (2) years

32

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL197D & ML197D
Appearance Net. weight Approx. 5.7 kg (w/o stand) 8.4 kg (w/ base)

Measurements (WxDxH) 432 x 65 x 353 mm (w/o base) *2

432 x 251 x 467 mm (w/ base)

Product color Graphite grey or white

Open frame Optional

Base unit Height adjustable Yes

Tilting and swivel Yes

Mounting Kensington lock Yes, prepared

VESA standard 100 mm

65

*1 Only applies to ML197D.

*2 Units with Protective glass (ML197D) or Touch panel are 69 mm deep.

33

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL227D
Display Screen size, Format 21,5, 16:9

Brightness, candela/m2 300

Contrast 800:1

Resolution, Megapixel 1920x1080, 2,1 Mpix

Response time 16ms

Viewing angles, H/V 178/178

Color depth 16,7M

Panel type MVA

Backlight type LED

Environmental Operating Storage

Temperature, Celcius 10~40°C -20~60°C

Humidity (non-condensation) 30~75% 10~90%

Air pressure 700~1060hPa 500~1060hPa

Input signal Connections (1) DVI-I (29-pin) connector:Compliant with DVI 1.0
(2) S-video connector: Color signal:0.286Vp-p/75 Ω Brightness
signal:1Vp-p/75 Ω
(3) BNC connector: Composite signal:1Vp-p/75 Ω
(4) Audio signal (pin jack3.5mm) connector:0.2-2.0 Vrms
(5) RJ 45 connector: Extended interface (OSD control)

Power Power supply 12v, 5A

Power consumption Approx. 40W Max. / Less than 2W in stand-by mode

Functionality Automatic adjustment Yes

OSD for settings PreVu™

Speakers Yes

Luminance compensation ALC

Pivot Yes

Protective glass No

Touch panel No

Dimming Optional

Sunlight Readable Optional, 550 cd/m2

DICOM pt. 14 preset Yes, 10 bit Barten

International standards Medical certificates No

IT certificates UL/cUL, FCC-B, CE, WEEE, RoHS

Warranty Replacement warranty Two (2) years

34

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL227D
Appearance Net. weight Approx 5,6 kg (w/o base unit)

Measurements (WxDxH) 537 x 65 x 329 mm (w/o base)

537 x 175 x 384 mm (w/ base)

Product color Graphite grey

Open frame No

Base unit Height adjustable No

Tilting and swivel Yes

Mounting Kensington lock Yes, prepared

VESA standard 100 mm

35

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL221D
Display Screen size, Format 21,5, 16:9

Brightness, candela/m2 300

Contrast 800:1

Resolution, Megapixel 1920x1080, 2,1 Mpix

Response time 16ms

Viewing angles, H/V 178/178

Color depth 16,7M

Panel type MVA

Backlight type LED

Environmental Operating Storage

Temperature, Celcius 10~40°C -20~60°C

Humidity (non-condensation) 30~75% 10~90%

Air pressure 700~1060hPa 500~1060hPa

Input signal Connections (1) DVI-I (29-pin) connector:Compliant with DVI 1.0
(2) S-video connector: Color signal:0.286Vp-p/75 Ω Brightness
signal:1Vp-p/75 Ω
(3) BNC connector: Composite signal:1Vp-p/75 Ω
(4) Audio signal (pin jack3.5mm) connector:0.2-2.0 Vrms
(5) RJ 45 connector: Extended interface (OSD control)

Power Power supply 12v, 5A

Power consumption Approx. 40W Max. / Less than 2W in stand-by mode

Functionality Automatic adjustment Yes

OSD for settings PreVu™

Speakers Yes

Luminance compensation ALC

Pivot Yes

Protective glass Yes, AG 80

Touch panel Optional, Projected Capacitive Touch (PCAP) USB & RS232

Dimming Optional

Sunlight Readable Optional, 550 cd/m2

DICOM pt. 14 preset Yes, 10 bit Barten

International standards Medical certificates No

IT certificates UL/cUL, FCC-B, CE, WEEE, RoHS

Warranty Replacement warranty Two (2) years

36

Downloaded from www.Manualslib.com manuals search engine

 Specifications
VL221D
Appearance Net. weight Approx 5,8kg (w/o base unit)

Measurements (WxDxH) 535 x 60 x 326 mm (w/o base)

537 x 175 x 384 mm (w/ base)

Product color White with grey front bezel

Open frame No

Base unit Height adjustable No

Tilting and swivel Yes

Mounting Kensington lock Yes, prepared

VESA standard 100 mm

37

Downloaded from www.Manualslib.com manuals search engine

 Special Considerations for LCD Panels
Manufacturing of LCD panels is very delicate with large panel elements being manufactured in
one unit and then cut to smaller sizes to be used in different products. In addition a panel consists
of several layers of components (back-light lamps, diffusers, electronics and color filters). There
are different technologies used with each having its advantages and disadvantages resulting in
end user products with different specifications even when taken from the same manufacturing
batch. Below are explanations to some observations that can be made and which are not
considered defects since they are merely problems inherent in the technology of LCD monitors.
Over time, the performance of the panel will also change.

Native resolution a new product. Due to wear of the backlight

All panels have a fixed number of pixels in lamps the values will change over time and
both horizontal and vertical directions. For gradually become lower.
instance is a 19” panel normally built with
1280 pixels horizontal and 1024 vertical giving Uniformity and Mura patterns
a native resolution of 1280x1024. At this Depending on the placement of the backlight
resolution you will get the sharpest picture and lamps, how many they are and the size of
it is therefore recommended that you use the the panel the brightness over the entire panel
native resolution. Thru scaling technologies it is will vary by up to 20%. Generally the highest
possible to use other resolutions but the picture brightness is in the centre of the panel and
will be less sharp. Some text will appear to becoming gradually lower towards the outer
have shadows. edges. This does not follow a linear curve
and there might also be “areas” on the screen
Native color temperature where there is a noticeable difference in the
Most commonly LCD panels are manufactured uniformity. Such clouded areas are referred
to have a color temperature of 6500K (Kelvin to as “Mura” and are more related to the
degrees) for full white picture. The color panel itself than to the backlight. These Mura
temperature can vary with shade of grey being patterns are different in size and shape and are
showed. For instance it could be 7500K at color and grayscale dependent since they are
50% grey and more than 9000 at 90% grey. a result from deterioration of the liquid crystal
For an individual panel the color temperature alignment layer. Mura is most commonly
at full white can also vary by +/- 15%. Inside caused by long term operation under high
the panel there is a color filter and over time ambient temperature and is a phenomenon
this will age and become more yellow in its that cannot be repaired.
color tone. Therefore, over time, the color
temperature will gradually go lower so that at Non-performing pixels
full white it could come down to 5000K. Each pixel on the panel actually consists of 3
sub-pixels (one for each of Red, Green and
Typical values Blue). A 19” panel with 1280x1024 therefore
In product specifications there are values for has almost 4 million sub-pixels. It can happen
brightness, contrast, view angles etc. The that a pixel can get stuck in ON status (bright
values are given as “typical values” meaning pixel defect) or in OFF status (dead pixel
that actual value for any given product can vary defect) or in an in-between status (low bright
by up to 20% from this value. For instance, pixel defect). Usually such defects only affect
a product specified to give 300 candela as a sub-pixel and not an entire pixel. The defect
typical maximum value for brightness may can therefore only be seen at certain color
for individual samples vary from 240 candela settings. The ISO 13406-2 standard specifies
to 360 candela. The values specified are for how many pixel defects that are acceptable
before an entire panel will be considered faulty.

38

Downloaded from www.Manualslib.com manuals search engine

 Special Considerations for LCD Panels
Olorin products are warranted to follow this Cable length and input signal
standard as a Class II product. When using long cables from the video source
(PC, camera etc) to the monitor the signal
Image sticking level will be lower and cause distortions in the
If the same image is shown for a long period of picture shown. A low quality graphic board
time there is a risk for “image sticking”. This is could also cause such problems. Always use
a result of that the thin film transistors will get high quality graphic boards and signal cables.
stuck in a certain position and continue to show
that image even when a new image is sent to
the panel. The image will disappear if you put
a full white picture on the monitor for several
hours. The best solution is to have a screen
saver that moves around on the screen so that
no static image is constantly shown.

Slow operating in cold environments

The thin film transistors contain some liquid
that will cause them to operate slowly in cold
temperatures. When temperature inside
the panel has increased to normal room
temperature, the speed will be up to normal
again.

39

Downloaded from www.Manualslib.com manuals search engine

 Longer life for your monitor
The components that have biggest influence The higher the luminance is set on the
on the useful life of the product are the monitor the greater is the wear of the backlight
backlight lamps. These are made of CCFL lamps. All monitors have the facility to adjust
(Cold-cathode Fluorescent Lamp). Over time brightness. Never set this at maximum since
these will decay and give less and less light. this will cause the lamps to decay faster. A
They generally have a spedification of 40,000 setting at 50% will be sufficient for use in office
hours before they are worn out. If they are environment.
constantly on one year of use corresponds to
just over 8,000 hours and thus a life of 5 years. Gradual change of color
As the backlight lamps ages they will show
There are ways to improve the useful life. a warmer color temperature which can be
The most radical and efficient way is to always perceived as more yellow for white color than it
switch the monitor off when not used. was initially when the monitor was new. There
are color filters in the panel which also will age
The second best is to use the Power Save and add to the yellowish color tone.
feature within the PC´s DPMA system. This
will not switch off the monitor entirely but the You can usually from the monitors OSD set
backlight lamps will be switched off which is your own color and by setting the value for blue
the important thing. When you start to use higher than red and green will change the color
the keyboard or mouse, the monitor will be temperature back to more normal. However,
switched on within a couple of seconds. the blue color filter has lower translucence so
the consequence is that you will get a lower
PLEASE, NOTE THAT A SCREENSAVER brightness.
WILL NOT SWITCH OFF THE BACKLIGHT
LAMPS AND THUS IS NOT A SOLUTION
FOR LONGER LIFE.

40

Downloaded from www.Manualslib.com manuals search engine

 Troubleshooting
Start your trouble shooting with the following actions

Possible power problem

• Make sure power is connected. If you switch the monitor off and then back on, the diode on
the front should show green light. Some models have a main power switch next to the power
inlet check that this is set to on. If you have a model without power adapter and still the no
green light it’s not a power problem.
• If not, check your power connection to the 12V/24V adapter and to the wall. There is a
similar diode on the 12V/24V adapter that should show green light.
• If not, the adapter might be broken. If you have another adapter of the same type you
can verify by using that adapter.
• If yes, there is a problem with the panel which should be repaired.
• If yes, then it is not a power problem.

Possible signal problem

• If picture is not stable or not shown at all or you get “No Sync” then check connection of the
signal cable and graphic board settings.
• If cable connections and graphic board settings are OK, then try the following
• Switch monitor off. Wait 10 seconds and switch it back on
• Re-boot the PC
• Test monitor by connecting it to another PC
• If nothing of this helps, then there is something wrong with the monitor and it should be
repaired. Contact your local reseller for assistance.

41

Downloaded from www.Manualslib.com manuals search engine

 Reference
Barten curve
Curve used to emphasize areas of a digital grayscale where the human eye have trouble
discerning similar shades of gray, named after its creator Dr. Peter G.J. Barten.

DDC *1
This unit conforms with DDC-2B and VESA *2 standards.

The DDC function reads information stored in the monitor about its capabilities. It communicates
over the 15-pin D-sub connector and the 24-pin DVI-D connector and it takes place during start-up
of Windows®. It sets the detailed information of the color LCD display in the system file in order to
achieve Plug & Play.

The video cable must be connected for reading of the information to take place.

*1 DDC (Display Data channel) and *2 VESA are registered trademarks of Video
Electronics Standards Association.

DICOM (Digital Imaging and Communications in Medicine)

DICOM is a standard for handling, storing, printing, and transmitting information in medical
imaging, Part 14 refers to the chapter: ”Grayscale Standard Display Function”.

Kensington Anti-Theft Security Lock Slot

The LCD monitor is equipped with a security lock slot compatible to Kensington® security lock
type. The security cable lock maybe available thru your dealer or it can be purchased at most
computer peripheral stores near you.

Power management
This unit conforms to the DPMS standard (Display Power Management Signaling).

42

Downloaded from www.Manualslib.com manuals search engine

 Contact

Olorin BV
Achterzeedijk 57,
Unit 53.
2992 SB Barendrecht
The Netherlands
Phone:+31 (0)180 699711
Fax: +31 (0)180 532121

E-mail: [email protected]

www.olorin.nl

OLM0002EN_1204

43

Downloaded from www.Manualslib.com manuals search engine