PLMRA402

Elite Series Waterproof Amplifier

400 Watt 4-Channel Amp System,
Dual MOSFET Power Supply
 Read through this user manual before using the product to ensure
its correct use. Keep this manual for future reference.

INTRODUCTION
The PLMRA402 has been designed using the latest electronic technology available.
The PLMRA402 is with engineered features allowing you to produce high quality
stereo repro duction in mobile applications. This innovative system has been
designed a 12 volts DC negative ground power supply.
Easy installation with mounting hardware is provided. The PLMRA402 has two
input levels. The high or low impedance input can be connected to units which
incorporate BTL circuity or common-ground types.

3 2 1 2 3

4
5

6 7
FIG 1

2 www.PyleUSA.com
FUNCTIONS

1. POWER ON LED: Lights up when the remote on system is energized.

2. INPUT GAIN CONTROL: Adjust high impedance input gain from 1 V to 300mV
for best matching with PREAMP output for your car stereo.

3. LOW IMPEDANCE INPUT (HIGH LEVEL INPUT): This unit is provided with two
terminal inputs (Front & Rear) for LOW impedance. If your car stereo has four
speaker outputs (LF, RF, LR, RR). Wire input as per FIG. 3 & FIG 3A.
If your car stereo has two speaker outputs, please wire as per FIG 4 & FIG 4A.

4. HIGH IMPEDANCE INPUT (LOW LEVEL INPUT): This unit is provided with gold
plated RCA input jacks for high impedance. Couple the RCA input with the car
stereo output using RCA type connector cables. If your stereo has only left and
right 2 channels outputs. You must use a Y-adaptor for connection (FIG 2).

5. POWER FUSE: Power fuse protects both this amplifier and the automobile
electrical system from wrong electrical conditions.

6. POWER SUPPLY TERMINAL: Connct the +12V DC power supply wire into this
terminal. By lugs and screws accessible at the panel of this amplifier (Fig. 5).

A. BATT + : Connect +12V DC power supply wire into this terminal from the (+)
terminal of the battery.

B. GROUND: Ground terminal connects the ground wire from the chassis of the
automobile.

C. REMOTE: Remote terminal connects the control wire which provides remote
turn-on and off of the amplifier by the RADIO/CASSETTE players power
antenna wire.

7. SPEAKERS TERMINALS: Speakers can be easily connected to signal barrier strip.

You may use 4 to 8 ohms speakers. Before connecting, please check speaker
connection diagrams.

www.PyleUSA.com 3
 ELECTRICAL AND AUDIO CONNECTIONS
A. STEREO INPUT CONNECTION
1. High impedance input

FRONT INPUT

FRONT INPUT
REAR INPUT

REAR INPUT
TO RIGHT

TO RIGHT
TO LEFT

TO LEFT

FRONT INPUT

FRONT INPUT
REAR INPUT

REAR INPUT
TO RIGHT

TO LEFT
TO RIGHT

TO LEFT
FROM LEFT FRONT PREAMP
OUTPUT OF CAR STEREO FROM LEFT
REAR PREAMP
FROM RIGHT FRONT PREAMP OUTPUT OF
OUTPUT OF CAR STEREO CAR STEREO
FROM RIGHT REAR PREAMP
OUTPUT OF CAR STEREO
FROM PREAMP FROM PREAMP
CAR STEREO LEFT OUTPUT RIGHT OUTPUT
OF CAR STEREO OF CAR STEREO

FIG 2

2. Low impedance (BTL or Common Ground) Input

a. Four Speaker Output Mode
a-1. Floating Ground Type
RR (+)

RF (+)
LR (+)

LF (+)
RR (-)

RF (-)
LR (-)

LF (-)

FIG 3 CAR STEREO

4 www.PyleUSA.com
 a-2. Common Ground Type

COMMON

COMMON
RR (+)

RF (+)
LR (+)

LF (+)
CAR STEREO
FIG 3A
b. Two Speaker Output Mode
b-1. Floating Ground Type
RIGHT (+)
RIGHT (-)
LEFT (+)

LEFT (-)

CAR STEREO
FIG 4

www.PyleUSA.com 5
 b-2. Common Ground Type

COMMON

RIGHT
LEFT

CAR STEREO
FIG 4A

NOTE: High and low impedance input cannot be used at same time.

B. SPEAKER CONNECTION
Connect the speaker output terminals to the corresponding speakers. (Figure 5)
The speakers must be high quality and capable of handling high power.
Separated return paths and strong wires are required. (Fig. 5)

NOTE:
This amplifier has built-in short circuit protection. If you mistakingly connect any
speaker wires to ground, or positive power (+) and (-) wires short together, the
protection circuit will operate automatically and cut-off output. In case of this,
you must switch OFF the whole system immediately double check speaker wire
connections and isolation before switching on the amplifier again.

6 www.PyleUSA.com
C. POWER CONNECTION

MAIN POWER LEAD

(TO CAR BATTERY
POSITIVE TERMINAL)

GROUND LEAD
(CONNECT TO A WELL 4 RIGHT SPEAKER 1 LEFT SPEAKER
GROUNDED METALLIC
PARTOF YOUR CAR)

REMOTE SWITCH
(CONNECT POWER ANT
(ACC) LEAD WIRE OF 3 LEFT SPEAKER 2 RIGHT SPEAKER
YOUR CAR STEREO)
FIG 5
1. Connect the B+12V pole of power supply directly to the battery (+) position
terminal.

2. Connect the GND pole of power supply directly to the (-) negative ground
battery terminal or car chassis.

3. To make a good grounding and prevent motor boating noise problem connect
another 12 gauge minimum wire from the (-) negative battery terminal to
chassis of stereo unit.

4. Connect the 'Remote' pole to external switch for positive 12V ON/OFF.
This may be connected to the receiver power antenna lead.

www.PyleUSA.com 7
 INSTALLATION
This amplifier comes complete with mounting hardware, if the unit is used in the
line level (high impedance) mode, it is recommended to use gold plated RCA
connection cables with the length as short as possible and mount the unit as
close as possible to the receiver. This will lower the chance of stray magnetic pick
up that may cause noise in the system.

1. Choose a suitable location.

2. Check the clearance behind and above the mounting area.

3. Wire unit according to the proper wiring digram.

4. Using the hardware provided, attach the unit to mounting surface.

8 www.PyleUSA.com
MAINTENANCE
Your PYLE power Amplifier is an example of superior design and craftsmanship.
The fllowing suggestions will help you care for your amplifier so you can enjoy it
for years.

Keep the amplifier dry. If it gets wet, wipe it dry immediately.

Liquids can contain minerals that corrode electronic circuits.

Use and stre the amplifier only in normal temperature environments.

Temperature extremes can shorten the lile of electronic devices and
distort or melt plastic parts.

Handle the amplifier gently and carefully. Dropping it can damage circuit
boards and cases and can cause theamplifier to work improperly.

Keep the amplifier away from dust and dirt which can cause premature
wear of parts.

Wipe the amplifier with a damp cloth occasionally to keep it looking new.
Do not use harsh chemicals, cleaning solvents, or strong deter gents to
clean the amplifier.

www.PyleUSA.com 9
 TESTING
1. After all the connections have been made, turn ON your stereo and listen for the
amplifier to turn ON. If there are any unusual noises from the speakers then turn
the system off and recheck all the wiring.

2. After you have connected your radio or equalizer to the amplifier, you may
adjust the gain control to match the output level of your radio.

A. Set the volume control on your radio to 2/3 position.

B. Adjust the gain control for an average listening level.

C. Turn the radio volume all the way down and listen for background noise.

D. Start your vehicle and listen for electrical noise.

E. Making fine adjustments to the sensitivity can reduce background noise and
some engine noise.

F. CAUTION: Never turn the sensitivity up any farther than you need to get clear
sound at 2/3 volume.

G. This adjustment only needs to be made once.

10 www.PyleUSA.com
Features:
• 4-Channel Amp System
• Dual MOSFET Power Supply
• Marine Grade Construction
• Waterproof Marine Rating IP-01
• Dual Adjustable Input GAIN Level Controls
• Dual High-Level Speaker Input Connectors
• Dual RCA (L/R) Input Connector Jacks
• Gold-Plated Speaker Output Terminal Connectors
• Adjustable Input GAIN Level Control
• Anti-Thump Delay Circuitry
• Built-in Thermal, Overload & Speaker Short Protection
• Heavy-Duty Aluminum Alloy Heatsink
• Power ON LED Indicator
• Remote Turn ON/OFF

What's in the Box:

• 4-Ch. Marine Amplifier
• Audio Connection Cables

Technical Specs:
• Output Power: 100 Watt x 4 MAX
• Amplifier Class: AB
• Fuse Type: 20A
• Input Gain Impedance Adjustment: 1 - 300mV
• Frequency Response: 15 - 30kHz +/-3dB
• Input Impedance: 10k Ohms (Low), 100 Ohm (High)
• Input Sensitivity: 250mV (Low), 2.5V (High)
• T.H.D.: <0.04%
• Matching Speaker Impedance: 4-8 Ohms
• Power Supply: DC 12V
• Dimensions (L x W x H): 9.0'' x 7.9'' x 2.0'' -inches

www.PyleUSA.com 11
 Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: [email protected]