PART OBSOLETE - NO ALTERNATE

PART

AP2008
PWM BUCK CONTROLLER

Features General Description

 PWM Buck Control Circuitry The AP2008 integrates Pulse-Width-Modulation (PWM) control
OBSOLETE – PART DISCONTINUED

 Operating voltage can be up to 20V circuit into a single chip, mainly designs for power-supply
 Under voltage Lockout (UVLO) Protection regulator. All the functions include an on-chip 0.77V reference
 Short Circuit Protection (SCP) output, an error amplifier, an adjustable oscillator, a soft-start,
 Soft-start circuit UVLO, SCP circuitry, and a push-pull output circuit. Switching
 Variable Oscillator Frequency -- 300Khz Max frequency is adjustable by trimming CT. During low VCC situation,
the UVLO makes sure that the outputs are off until the internal
 0.77V voltage reference Output
circuit is operational normally.
 8-pin SOP package
 SOP-8L: Available in “Green” Molding Compound
(No Br, Sb)
 Lead Free Finish/ RoHS Compliant (Note 1)

Applications

 Backlight inverter
 LCD Monitor
 XDROM, XDSL Product
 DC/DC converters in computers, etc.

Ordering Information

AP 2008 S X - 13

Package Lead Free Packing

S : SOP-8L L : Lead Free 13 : Tape & Reel
G : Green

Package Packaging 13” Tape and Reel

Device
Code (Note 2) Quantity Part Number Suffix
Lead-free
AP2008SL-13 S SOP-8L 2500/Tape & Reel -13
AP2008SG-13 S SOP-8L 2500/Tape & Reel -13
Notes: 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.

AP2008 1 of 8 June 2020

Document number: DS31047 Rev. 3 - 4 www.diodes.com © Diodes Incorporated
 AP2008
PWM BUCK CONTROLLER

Pin Assignments

( Top View )

OUT 1 8 GND

VCC 2 7 CT

COMP 3 6 SS

FB 4 5 SCP

SOP-8L

Pin Descriptions

Pin Name Description

OUT PWM Output

VCC Supply Voltage
COMP Feedback Loop Compensation
FB Voltage Feedback
SCP Short Circuit Protection
SS Soft-Start.
CT Timing Capacitor
GND Ground

AP2008 2 of 8 June 2020

Document number: DS31047 Rev. 3 - 4 www.diodes.com © Diodes Incorporated
 AP2008
PWM BUCK CONTROLLER

Block Diagram
VCC SS CT

10K-300KHz / CT value
2.5V
0.77V Bandgap Internal use
UVLO Oscillator
Reference
VCC

Iss
PWM Amplifier
FB
+ OUT
+
-
Error Amplifier

COMP
- 0.7V
-
1.5V +
+

SCP GND

Absolute Maximum Ratings

Symbol Parameter Rating Unit

VCC Supply voltage 22 V
VI Amplifier input voltage 20 V
VO Collector output voltage VCC-1.0V V
ISOURCE Source current 200 mA
ISINK Sink current 200 mA
o
TOP Operating temperature range -20 to +85 C
o
TST Storage temperature range -65 to +150 C

Recommended Operating Conditions

Symbol Parameter Min Max Unit

VCC Supply voltage 3.6 20 V
VI Amplifier input voltage 1.05 1.45 V
VO Collector output voltage Vcc-1.5 V
IFB Current into feedback terminal 45 µA
RF Feedback resistor 100 kΩ
CT Timing capacitor 100 6800 pF
FOSC Oscillator frequency 10 300 KHz

AP2008 3 of 8 June 2020

Document number: DS31047 Rev. 3 - 4 www.diodes.com © Diodes Incorporated
 AP2008
PWM BUCK CONTROLLER

Electrical Characteristics (TA=25ºC, VCC=6V, f=200 Khz)

Reference (REF)
Symbol Parameter Conditions Min Typ. Max Unit
Comp connect to FB 0.755 0.770 0.785 V
VREF Output voltage change with TA = -20ºC ~ 25ºC -0.1 ±1 %
temperature TA = 25ºC ~ 85ºC -0.2 ±1 %
Under voltage lockout (UVLO)
Symbol Parameter Conditions Min Typ. Max Unit
VUT Upper threshold voltage (VCC) 2.9 V
IO(REF) = 0.1mA
VLWT Lower threshold voltage (VCC) 2.4 V
TA = 25ºC
VHT Hysteresis (VCC) 500 mV
Short-circuit protection (SCP) control
Symbol Parameter Conditions Min Typ. Max Unit
VIT Input threshold voltage TA = 25ºC 0.60 0.67 0.75 V
VSTB Standby voltage No pull up 100 130 160 mV
VLT Latched input voltage No pull up 50 100 mV
ISCP Input (source) current VI = 0.7V, TA = 25ºC -10 -15 -20 µA
Comparator threshold voltage
VCT 1.5 V
(COMP)
Oscillator (OSC)
Symbol Parameter Conditions Min Typ. Max Unit
FOSC Frequency CT =270 pF 200 KHz
Standard deviation of frequency CT =270 pF 10
ΔFOSC %
Frequency change with voltage VCC=3.6V ~ 20V 1
Error-amplifier
Symbol Parameter Conditions Min Typ. Max Unit
VIO Input offset voltage VO (FB)=0.77V ±6 mV
IIO Input offset current VO (FB)=0.77V ±100 nA
IIB Input bias current VO (FB)=0.77V 160 500 nA
VCM Common-mode input voltage range VCC=3.6V ~ 20V 1.05 1.45 V
AV Open-loop voltage amplification RF=200 kΩ 70 80 dB
GBW Unity-gain bandwidth 1.5 MHz
CMRR Common-mode rejection ratio 60 80 dB
VOH Max. output voltage Vref-0.1 V
VOL Min. output voltage 1 V
IOI Output (sink) current (COMP) VID = -0.1V, VO = 0.77V 0.5 1.6 mA
IOO Output (source) current (COMP) VID = 0.1V, VO = 0.77V -45 -70 µA

AP2008 4 of 8 June 2020

Document number: DS31047 Rev. 3 - 4 www.diodes.com © Diodes Incorporated
 AP2008
PWM BUCK CONTROLLER

Electrical Characteristics (Continued) (TA=25ºC, VCC=6V, f=200 Khz)

Output section
Symbol Parameter Conditions Min Typ. Max Unit
ILEAK Leakage current VO = 20V 10 µA
Sink current VIN= 12V 200 mA
IDRV
Source current VIN= 12V 200 mA
VSAT Output saturation voltage IO = 10 mA 1.0 1.5 V
ISC Short-circuit output current VO = 6V 120 mA
PWM comparator
Symbol Parameter Conditions Min Typ. Max Unit
VT0 Input threshold voltage at f = 10 KHz CT=6800pF 0.6 0.7 V
VT100 (COMP) Maximum duty cycle 1.2 1.3 V
Total device
Symbol Parameter Conditions Min Typ. Max Unit
ICCA Average supply current CT = 270pF 6 10 mA
Soft Start
Symbol Parameter Conditions Min Typ. Max Unit
VSS Soft-start Voltage 2.3 V
ISS Constant Charge Current 20 µA

Typical Application Circuit

R3 30K
Vcc = 12V
C2
10nF Q1 C1
(Optional) 470uF
P mos
L1
4
3 COMP SS 6
2 VCC
1 OUT GND 8

10uH Output
FB

1V/5A
5A C4
R1
1K 50nF
SCP 5

(Optional) C3
CT 7

470uF
R2
4K
C4 270pF
C5 50nF
C6 220nF

Step-Dow n DC/DC conv erter

AP2008 5 of 8 June 2020

Document number: DS31047 Rev. 3 - 4 www.diodes.com © Diodes Incorporated
 AP2008
PWM BUCK CONTROLLER

Typical Characteristics

REFERENCE OUTPUT VOLTAGE AVERAGE SUPPLY CURRENT

vs. vs.
POWER-SUPPLY VOLTAGE POWER-SUPPLY VOLTAGE
0.785
5
0.78
Voltage (V)

Supply Current
Reference

Icc-Average
4
Output

0.775
Vref-

(mA)
0.77
0.765 2
0.76 1
0.755 0
4 6 8 10 12 14 16 18 20 0 4 8 12 16 20
Vcc-Power Supply Voltage (V) Vcc - Power-Supply Voltgae (V)

VCT(min)
AVERAGE SUPPLY CURRENT VCT vs. FREQUENCY VCT(max)
vs.
AMBIENT TEMPERATURE 1.6
7
1.4
Supply Current

6 1.2
ICC - Average

1
VCT (V)

5
(mA)

0.8
4 0.6
0.4
3 0.2
0
2
0 100 200 300
-50 -25 0 25 50 75 100
TA - Ambient Temperature (℃) Frequency (KHz)

OSCILLATOR FREQUENCY SCP TIME-OUT PERIOD

vs. vs.
TIMING CAPACITANCE SCP CAPACITANCE
350 35
tscp-SCP Time-out
fosc - Frequency

300 30
Period (ms)

250 25
20
(KHz)

200
15
150
10
100
5
50
0
0
100 600 1100 1600 2100 2600 3100 3600 4100 4600 5100 5600 6100 6600
45 90 135 180 225 270 315 360 405 450 495

CT-Timing Capacitor (pF) Cscp - SCP Capacitance (nF)

AP2008 6 of 8 June 2020

Document number: DS31047 Rev. 3 - 4 www.diodes.com © Diodes Incorporated
 AP2008
PWM BUCK CONTROLLER

Typical Characteristics (Continued)

SOFT-START TIME (Ts)

vs.
SOFT-START CAPACITOR (Css)
30
25
20
Ts (mS)

15
10
5
0
25 50 75 100 125 150 175 200
Css (nF)

Marking Information

(1) SOP-8L

( Top View )
8 5
Logo L : Lead Free
G : Green
Part Number AP2008
YY WW X X YY : Year : 08, 09,10~
WW : Week : 01~52; 52
represents 52 and 53 week
X : Internal Code
1 4

AP2008 7 of 8 June 2020

Document number: DS31047 Rev. 3 - 4 www.diodes.com © Diodes Incorporated
 AP2008
PWM BUCK CONTROLLER

Package Information (All Dimensions in mm)

(1) Package Type: SOP- 8L

3.85/3.95
5.90/6.10

0.254
0.10/0.20

Gauge Plane
Seating Plane
0.62/0.82
Detail "A"

7°~9° 7°~9°
0.35max. 45°
0.15/0.25
1.30/1.50
1.75max.

Detail "A"
0°/8°

1.27typ 0.3/0.5

4.85/4.95

8x-0.60
5.4

6x-1.27
8x-1.55

Land Pattern Recommendation

(Unit: mm)

IMPORTANT NOTICE

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further
notice to any product herein. Diodes Incorporated does not assume any liability arising out of the application or use of any product described herein; neither
does it convey any license under its patent rights, nor the rights of others. The user of products in such applications shall assume all risks of such use and will
agree to hold Diodes Incorporated and all the companies whose products are represented on our website, harmless against all damages.

LIFE SUPPORT

Diodes Incorporated products are not authorized for use as critical components in life support devices or systems without the expressed written approval of the
President of Diodes Incorporated.

AP2008 8 of 8 June 2020

Document number: DS31047 Rev. 3 - 4 www.diodes.com © Diodes Incorporated