The Hong Kong Polytechnic University

Department of Electrical and Electronic Engineering

High Voltage Engineering

EE509
Prof. Derek S. W. Or

2023 / 2024
Contents
Chapter 1 Introduction to Electrical Insulation ................................................................................ 1-1
1.1 Background ........................................................................................................................................ 1-1
1.2 Electric Fields .................................................................................................................................... 1-1
1.3 Dielectric Breakdowns ...................................................................................................................... 1-4
1.4 Fundamentals of Gaseous, Liquid, and Solid Insulation and Breakdown ........................................ 1-5
1.4.1 Gaseous Insulation and Breakdown .................................................................................... 1-5
1.4.2 Liquid Insulation and Breakdown ....................................................................................... 1-6
1.4.3 Solid Insulation and Breakdown ......................................................................................... 1-7
1.5 Industrial Applications of Electrical Insulating Materials ................................................................ 1-9
1.5.1 Essences of Applications..................................................................................................... 1-9
1.5.2 Applications in Rotating Machines ................................................................................... 1-11
1.5.3 Applications in Cables ...................................................................................................... 1-12
1.5.4 Applications in Power Transformers ................................................................................ 1-13
1.5.5 Applications in Power Capacitors ..................................................................................... 1-15
1.6 Supplementary Information on Insulating Materials ...................................................................... 1-17
1.6.1 Sulphur Hexafluoride (SF6) Gas ....................................................................................... 1-17
1.6.2 Petroleum Oil (Transformer Oil) ...................................................................................... 1-20
1.6.3 Solid Dielectrics ................................................................................................................ 1-22
1.7 References........................................................................................................................................ 1-36

EE509 High Voltage Engineering ii

Chapter 1 E = V/d

Introduction to Electrical Insulation

1.1 Background

In modern times, high voltages are used in various applications covering electrical power systems, renewable
energy systems, transportation systems, communication systems, medical equipment, research laboratories, etc.
These applications are essential to sustain modern civilization. For example, high voltages are utilized to transmit
large bulks of power over long distances; are employed to energize high-speed and intercity railway systems; are
used to sustain the operation of power transmitters; are deployed in X-ray tubes for medical equipment; and are
applied in laboratories for nuclear research. The various conditions under which high voltages are used require a
careful design of their electrical insulation. The principal media of electrical insulation are: (1) Gases (including
vacuum), (2) Liquids, (3) Solids, and (4) A combination of them (e.g., coils/transformers with epoxy molding and composite
system
oil impregnation). For reliability, safety, and economic reasons, modern electrical engineers should have adequate
knowledge of electrical insulating materials and insulation failures. In this chapter, some of the general
principles, concepts, materials, and applications of electrical insulation are introduced.
most high voltage failure is insulation failure

1.2 Electric Fields

The electric field intensity E (units: V/m) at any location in an electrostatic field is the ratio of the force acting
on an infinitely small (point) charge at that location to the charge itself as the charge reduces to zero. The force F
acting on any charge q at that point in the field is given by Coulomb’s law as follows:
electron inside a E field, force will be generated
𝐅 = 𝑞 𝐄. (1.1)

EE509 High Voltage Engineering 1-1

 The electric flux density D (units: C/m2) associated with the electric field intensity E is
Q <--> flux interchangable flux/V = permittivity * A/d = C
𝐃 = 𝜀 𝐄, (1.2)

where 𝜀 = 𝜀r 𝜀0 (units: F/m) is the permittivity of the (dielectric) medium in which the electric field exists; 𝜀r is the
relative permittivity or the dielectric constant; and 𝜀0 = 8.85410–12 F/m is the permittivity of free space or the
absolute permittivity.

The work done on a charge moving in an electric field is defined as the electric potential 𝜑 (units: V), which, in
integral form, is expressed as

𝜑 = ∫𝑙 𝐄 𝑑𝑙, (1.3)

where l is the path through which the charge is moved.

The electric field intensity E, in point form, is numerically equal to the electric potential gradient 𝛁𝜑 by
e field can be used for direct comparison, because per unit stregth
V, voltage, not used for direct comparison, because not per unit strength𝐄 = −𝛁 𝜑, E = -gradient( potential ) (1.4)

where 𝛁 (gradient, read “del” operator) is a vector differential operator defined as

𝜕 𝜕 𝜕
𝛁 ≡ 𝑖̂ + 𝑗̂ + 𝑘̂
𝜕𝑥 𝜕𝑦 𝜕𝑧
in the rectangular coordinate.

It is noted that electrons can move freely in a conductor under the influence of an electric field. This means that
the charges are distributed inside and over the surface of the conductor such that E = 0 in all places of the
conductor. Since E in Eq. (1.4) vanishes, it is necessary that 𝜑 is constant inside and on the surface of the
conductor; that is, the conductor has an “equipotential” surface with maximal charges and currents.

EE509 High Voltage Engineering 1-2

 In the presence of an electric field, a coordinate movement of free electrons occurs, but the average space
charge density remains zero at any point in the conductive medium. This movement of free electrons is referred to
as an electric current and can be described as a current density vector J. In a conductive medium, the relationship
between J and E is known as Ohm’s law:

𝐉 = 𝜎𝐄, (1.5)

where  is the conductivity of the medium (units: S).

The electric (conduction) current I passing through some open surface is defined as the net positive charge Q
passing through that surface per unit of time t as follows:
𝑑𝑄
𝐼= . (1.6)
𝑑𝑡

A simple capacitor consists of two conductors separated by a dielectric medium. If one conductor surface
contains positive charge +Q and the other has negative charge –Q, and if the potential difference between them is
𝜑12 , the capacitance of such a capacitor is defined as the ratio of charge Q to the potential difference 𝜑12 by
𝑄
𝐶= . (1.7)
𝜑12

If the charge is not distributed uniformly over the two conductor surfaces, and if the charge density is ρ and the
electric field intensity in the dielectric medium is E, then
∬ 𝜌𝑑𝑆
𝐶 = 2S , (1.8)
∫1 𝐄 𝑑𝑙
where S is the closed surface containing the charge and l is the path through which the charge is moved.

EE509 High Voltage Engineering 1-3

 1.3 Dielectric Breakdowns

In high voltage equipment, the essential materials used are: (1) Conductors and (2) Insulators. Conductors
promote the flow of electric currents, while insulators prevent the flow of electric currents to undesired paths or
circuits. If for some reason, the flow of an electric current deviates from the desired path or circuit, the electric
potential associated with that path or circuit will drop, as in the case of a “short circuit”.

Usually, all dielectrics are good insulators at sufficiently low magnitudes of electric field intensities. However,
as the applied electric field increases, the electrons bound to the molecules of the dielectrics will be subject to
higher forces, as reflected by Eq. (1.1): 𝐅 = 𝑞 𝐄, and some of them will be “free” from their molecular bonding.
The electrons move in the opposite direction to the applied electric field, thus creating an electric current as
material
indicated by Eq. (1.6): 𝐼 = 𝑑𝑄/𝑑𝑡. This is a temporary phenomenon in gases in which a combination occurs when property
the electric field is removed but is a partial or permanent phenomenon in liquids and solids. The phenomenon is
called dielectric breakdown. The magnitude of an electric field leading to the dielectric breakdown and the
just
kV/cm=V/d destruction of the insulation properties of the dielectric materials is called dielectric breakdown strength. It is maxiumum
=e-field; usually expressed in kV/cm, MV/cm, or MV/m. The basic ideas of the electrical insulating materials and their E field
before
efield ! breakdown mechanisms are highlighted in later sections, while their details are discussed in subsequent chapters. breakdown
=efields e-fieldS: whole area; e-field: ????
Besides the dielectric breakdown strength ⎯ an intrinsic property of insulating materials, the electric field
stress developed in insulating materials when subjected to a high voltage is another important parameter in high
voltage engineering. According to Eq. (1.4): 𝐄 = −𝛁𝜑, the electric field stress acting on an insulating material is gives E
equal to E and is numerically equal to 𝛁𝜑. In other words, the dielectric breakdown strength of an insulating field, actually will
material can be defined as the maximum dielectric stress that the material can withstand. It can also be stress the
material
characterized by the maximum electric field stress required to cause a breakdown in a dielectric insulation. The
dielectric breakdown strength of insulating materials depends on various parameters such as pressure, temperature,
humidity, field configurations, nature of applied voltage, imperfections in dielectric materials, electrode materials,
surface conditions of electrodes, etc. An understanding of the failure of the insulation will be possible by studying
the insulation breakdown mechanisms to be discussed in the following chapters.

EE509 High Voltage Engineering dieletric strength is the external, E; this gives stress to material 1-4
 1.4 Fundamentals of Gaseous, Liquid, and Solid Insulation and Breakdown
Photo electric + 2nd ionization + collision ionization =
1.4.1 Gaseous Insulation and Breakdown
tungsen breakdown ionization

Breakdown in gases occurs as a result of collision ionization. Electrons can be emitted from the cathode
electrode if the electric field stress is 100–1,000 kV/cm due to field emission. Electrons in the outermost orbit bear valence
the least attraction forces from the central nucleus, so they can be “free” easily by collision of electrons. Electrons shell
get multiplication exponentially, and breakdown occurs when the applied electric field stress is sufficiently large.
gap small: The breakdown strength of gases increases steadily with the gap distance between the electrodes. Meanwhile, the
large E field electric field stress reduces greatly from ~30 kV/cm for small gaps of several centimeters to ~6 kV/cm for
gap large: large gaps of several meters under uniform fields. For very large gaps, as in lightning, the average stress reduces to E=V/d,
small e- small gap,
field
1–3 kV/cm. The breakdown in gases can be described by Townsend and Streamer breakdown mechanisms. E large;
bec. E = v/d large gap,
Air at atmospheric pressure is the most common gaseous insulation with a breakdown strength of ~100 kV/cm. E small
High-pressure (or compressed) gases have more considerable breakdown strengths because free electrons have
been intentionally attached to neutral gas molecules to form negative ions via an electron attachment process.
Nitrogen (N2) was the first high-pressure gas used due to its inertness and chemical stability, but its breakdown
strength is the same as that of air. Other practical insulating gases include carbon dioxide (CO2),
dichlorodifluoromethane (CCl2F2) (a nonflammable hydrocarbon popularly known as Freon), and sulfur
hexafluoride (SF6). Among them, SF6 has the most attractive arc quenching properties and breakdown strength of
~250 kV/cm (~2.5 times larger than N2 and CO2 at atmospheric pressure).

Vacuum is the best insulator with breakdown strengths up to 10,000 kV/cm, limited only by emission from the
electrode surfaces. Breakdown strength decreases to <100 kV/cm for a gap distance of several centimeters. Under
high vacuum conditions where pressures are as low as 10–3–10–6 torr (1 torr = 1 mm of Hg), a breakdown cannot
generally occur. Vacuum insulation is used in particle accelerators, X-ray and field emission tubes, electron
microscopes, capacitors, circuit breakers, etc.
what did he say about vaccum?
E, d, Pressure, Temp
EE509 High Voltage Engineering 1-5
1.4.2 Liquid Insulation and Breakdown

Liquids are mainly used to provide the dual purpose of electrical insulation and heat conduction (or removal).
The most attractive feature of liquid insulation is the self-healing of puncture paths. That is, a temporary failure due
to overvoltage is reinsulated quickly by liquid flow to the attacked area. However, discharge products may deposit
on solid insulation supports, leading to surface breakdown over the solid supports.
gas bubble killer of water's insulation
Highly purified liquids have breakdown strengths as high as 1,000 kV/cm, being ~10 times higher than air and
N2. Under actual service conditions, however, the breakdown strength reduces greatly due to impurities. The
breakdown mechanism is similar to the gas breakdown in highly purified liquids. Still, in commercial liquids, the
breakdown mechanisms are significantly changed by the presence of impurities (e.g., gas or vapor bubbles,
moisture or water droplets, solid particles, etc.) with several times reduction in the breakdown strengths in general.

The important electrical properties of liquid insulation include dielectric strength, conductivity, flash point, gas
content, viscosity, dielectric constant, dissipation factor, stability, etc. Petroleum oils (transformer oils) are the
most common commercial liquids with breakdown strengths of ~150 kV/cm. Askarels (the generic name for
synthetic chlorinated aromatic hydrocarbons; very toxic) (200–250 kV/cm) and silicone oils (300–400 kV/cm) are
used in transformers and capacitors due to their high operating temperatures above 200 ºC. Organic esters
(including castor oils) (~200 kV/cm) and polybutenes are suitable for high voltage energy storage capacitors
because of their low dielectric losses. Hexanes (~300 kV/cm) are helpful for cables. maintain temp. to avoid degradation of
oil
In practical applications, liquids are generally used at much reduced electric field stress levels of 50–60 kV/cm
to minimize the effect of heating when the equipment is continuously operated. In applications like high voltage
bushings where the liquid only fills up the voids in the solid dielectrics, it can be used at elevated electric field
stress levels of 100–200 kV/cm.

EE509 High Voltage Engineering 1-6

1.4.3 Solid Insulation and Breakdown

Homogenous and truly perfect solids have breakdown strengths as high as 10,000 kV/cm, 10 times higher than
liquids and 100 times larger than air. The breakdown in solids occurs over the surface rather than in the solid
themselves, so surface insulation failure is the most frequent cause of trouble in practice.

When a breakdown occurs on the surface of a solid insulator, it can be a simple flashover of the surface or the
formation of a conducting path on the surface called tracking, both resulting in the degradation of the insulation.
Surface flashover often occurs in the case when the solid insulator is immersed in a liquid dielectric. Porcelain
(ceramic) insulators for power transmission lines are designed to have a long path over the surface, typically 20–30
times greater than that through the solid. However, a surface breakdown is still a frequent type of failure.
especially for undergrd cable
The failure of solid insulation itself is called treeing. The phenomenon occurs when imperfections appear either
at the interfaces between the solid insulators and the conductors or inside the solid insulators.

Generally, solid insulation failure by discharges is called partial discharges (PDs). PDs may occur in the
internal voids and cavities of the solids. The energy dissipated in the PDs causes further deterioration of the cavity
walls and gives rise to further gas evolution. This is a cumulative process, eventually leading to a breakdown. PDs
are receiving much attention today since it determines a solid insulator's life versus stress characteristics. In
practice, it is impossible to eliminate PDs fully, but it is possible to control them at a certain level by the expected
working life of the equipment. For high voltage applications, cast epoxy resin (a thermosetting polymer) can solve
many problems, but great care should be taken during casting. Vacuum impregnation of the insulation can also
help minimize the effect of PDs. High voltage switchgears, bushings, cables, and transformers are typical devices
for which PDs should be considered in the design phase.

EE509 High Voltage Engineering 1-7

 As an essential supplement to electrical solid conductors and insulators, Fig. 1.1 shows the intrinsic physical
properties of the three basic categories of solid materials: (1) Metals, (2) Ceramics, and (3) Polymers.
conductor
insulator
insulator

thermal is much higher than metal's

Fig. 1.1 Intrinsic physical properties of metals, ceramics, and polymers.

EE509 High Voltage Engineering 1-8

1.5 Industrial Applications of Electrical Insulating Materials

1.5.1 Essences of Applications

In practice, no piece of electrical equipment does not need electrical insulation to prevent the flow of electric
current to undesired paths or circuits. Electrical insulation is used wherever there is a potential difference between
adjacent conducting bodies that carry currents. There are four main areas where electrical insulation must be
applied. They are:

(a) Between turns in a coil (inter-turn),

(b) Between coils of the same phase (inter-coil),
(c) Between coils of different phases (phase-to-phase), and
(d) Between coils and earth (phase-to-earth).

There are three main categories of electrical insulating materials: (1) Gases, (2) Liquids, and (3) Solids. While
insulation is primarily used to resist electric field stresses, the performance of an insulator depends on its operating
temperature. The higher the temperature, the higher the rate of its chemical deterioration and the lower the useful
life will result. Thus, it is required to determine the operating temperature limit for insulation in order to ensure
safe operation over its expected life. In the field of electrical insulation, the insulating materials are generally
grouped into four different classes as follows:

Class O: Up to 90 ºC Organic materials (papers, polymers, woods, cottons, pressboards,

waxes, etc.) without impregnation.
Class A: Up to 105 ºC Organic materials with impregnation.
Class B: Up to 130 ºC Inorganic materials (glasses, ceramics, mica, etc.) with a binder.
Class C: No specific limit Inorganic materials without a binder.

EE509 High Voltage Engineering 1-9

 With the development of newer insulating materials (e.g., plastics and silicones) during the middle of the last
century, a need was felt to reorganize the classification of the insulating materials. This led IEC (International
Electrotechnical Commission) to come up with the following new classes:

Class Y (formerly O): 90 ºC Paper, cotton, silk, natural rubber, polyvinyl chloride (PVC), etc.
without impregnation.
Class A: 105 ºC Same as Class Y but with impregnation, plus nylon.
Class E: 120 ºC Polyethylene terephthalate (PET) (terylene fiber, melinex film),
cellulose triacetate, polyurethanes (PU), polyvinyl acetate (PVA)
enamel.
Class B: 130 ºC Mica, fiberglass (alkali free alumino borosilicate), bituminized
asbestos, Bakelite (phenolics), polyester (PET) enamel.
Class F: 155 ºC As Class B but with epoxy- and alkyd-based resins.
Class H: 180 ºC As Class B but with silicone resin binder, silicone rubber, aromatic
polyamide (nomex paper and fiber), polyimide film (enamel, varnish
and film), and stermide enamel.
Class C: >180 ºC As Class B but with suitable inorganic binders; Teflon telfon, king of
(polytetraflouroethylene, PTFE). polymer
The temperatures mentioned above can only be regarded as an index to compare the various insulating
materials; they cannot be treated as the limiting operating temperatures. All the standards permit the equipment to
work up to these temperatures, but certain differentials are allowed in practice because of the overloads,
manufacturing advantages, and economics.

EE509 High Voltage Engineering 1-10

1.5.2 Applications in Rotating Machines

Rotating machines are generally divided into two groups: (1) Low Voltage Machines with ratings <6.6 kV and
(2) High Voltage Machines. High voltage machines with ratings >22 kV are not usually built due to the difficulty
in insulating superhigh voltages. Table 1.1 shows the various materials used in modern rotating machines. The two
extreme classes, Class Y (90 ºC) and Class C (>180 ºC), find no application in rotating machines. Class E (120 ºC),
which has been widely used in low voltage machines for over 20 years, is now being replaced by Class F (155 ºC)
for higher voltage machines. Also, Class F is being increasingly used in place of Class B (130 ºC). Hence, Class F
appears to be the insulation of the future. Considerable progress has been made in recent years to reduce the size of
the machines for a given rating by using Class H (180 ºC) and Class C, particularly for small machines. However,
the costs of Class H (with silicones) and Class C (with Teflon) are very high, and they are only used under special
conditions like severe overloads in traction and mill motors.

Table 1.1 Various materials used in modern rotating machines.

EE509 High Voltage Engineering 1-11

1.5.3 Applications in Cables

The physical properties required for wire and cable insulation depend on the type of application. Electrically,
they should also have low dielectric permittivity, dielectric loss, and power factor but high dielectric strength and
insulation resistance. Mechanically, they should have good elongation, tensile strength, and toughness to withstand
handling during installation and service. Thermally, they should have excellent resistance to aging at high
temperatures and withstanding long exposure to sunlight and various chemicals. In an underwater environment,
they should have very low water absorption. In a low-temperature setting, they should not become stiff and brittle.

Table 1.2 gives the various insulating materials for cables and their maximum cable operating voltages and
range of operating temperatures. Paper-insulated, lead-sheathed cables are still used because of their high dielectric
strength, low dielectric loss, and long service life, despite their low operating temperatures (<100 ºC). Polyvinyl
chloride (PVC) and polyethylene (PE) are commonly used in low and medium voltage (<3.3 kV) cables. Teflon
(PTFE) is best-suited for high voltage (<5 kV) and temperature (<250 ºC) operations. Silicone rubber forms very
little carbon when destroyed by fire, and as such, it continues to function even after the fire. It is thus used for
aircraft cables where contamination with aircraft fuel can occur at high temperatures.

Table 1.2 Some important insulating materials for cables.

EE509 High Voltage Engineering 1-12

1.5.4 Applications in Power Transformers

Transformers are liable to lightning and other high voltage surges, so the insulation has to withstand very high
impulse voltages many times the power frequency operating voltages. The transformer insulation is broadly
divided into five main areas:

(a) Conductor or turn-to-turn insulation,

(b) Coil-to-coil insulation,
(c) Low voltage coil-to-earth insulation,
(d) High voltage coil-to-low voltage coil insulation, and
(e) High voltage coil-to-ground insulation.

For (a), organic enamel is directly applied to the conductor in smaller rating transformers, whereas paper or
glass tape is wrapped on the rectangular conductors in higher rating transformers.

For (b), Kraft paper is used in smaller transformers, whereas thick radial spacers made of pressboard, glass
fabric, or porcelain are used in higher rating transformers.

For (c), (d), and (e), solid tubes combined with liquid- or gas-filled spacers are used to help in removing the
heat from the core and coil structure and also in improving the insulation strengths.

Oil-impregnated paper and pressboard are extensively used in liquid-filled transformers. However, the lack of
thermal stability at higher temperatures limits their use in continuously operated transformers up to 105 ºC. Also,
paper absorbs moisture very rapidly from the atmosphere, so it should be kept free of moisture during its life in
transformers.

EE509 High Voltage Engineering 1-13

 Transformer oil (petroleum oil) provides the required dielectric strength and insulation, besides cooling the
transformer by circulating itself through the core and the coil structure. However, it should be in the liquid state
over the complete operating temperature range of –40 to +50 ºC. The transformer oil gets oxidized when exposed
to oxygen (O2) at high temperatures, resulting in the formation of undesirable products such as peroxides, water,
organic acids, and sludge. These products cause chemical deterioration of the paper insulation and the metal parts
of the transformer. Sludge, being heavy, reduces heat transfer by forming a heat-insulating layer on the coil
structure, the core, and the tank walls. In present-day transformers, the oxidation problem is minimized by using
sealed transformers, filling the air space with N2 gas, and providing O2 absorbers like activated clay or alumina.

When an arc discharge occurs inside a transformer, oil decomposition occurs and produces explosible products
of hydrogen and hydrocarbon gases. Thus, oil-insulated transformers are seldom used inside buildings or other
hazardous locations like mines, but dry-type and liquid (Askarel)- or gas (SF6)-filled transformers are used instead.
Askarel is a fireproof liquid, more stable to oxidation and arcing, and does not form acids or sludge at the expense
of giving out very toxic and paper insulation-attackable hydrochloric acid. Also, Askarel cannot be used in high
voltage transformers because the impulse strength of Askarel-impregnated paper is very low compared to the
oil-impregnated paper. Moreover, its dielectric strength rapidly deteriorates at high voltages and frequencies,
releasing hydrochloric acid.

Even today, there is no perfect all-purpose transformer fluid. In recent years, progress has been made with
fluorocarbon liquids and SF6 gas. SF6-insulated transformers have become popular, but fluorocarbon liquids are not
because of their high cost.

EE509 High Voltage Engineering 1-14

1.5.5 Applications in Power Capacitors

Power capacitors are indispensable for power system administration, power transmission system voltage
regulation, and power factor improvement of power distribution networks. They are made in simple units with
voltage ratings of 220–13,800 V and kVAR ratings varying from 0.5 to 25 kVAR. They are generally formed by
several layers of insulating paper of adequate thickness and aluminum foil of 6 μm thickness as electrodes are
interleaved and wound. Single units are connected in parallel depending on the rating of the capacitor unit to be
manufactured. These are placed in containers hermetically sealed, thoroughly dried, and then impregnated with
insulating oil.

The insulation paper should have high dielectric strength, low dielectric loss, high dielectric constant, uniform
thickness, and minimum conducting particles. Polypropylene (PP) film generally has good properties, but paper is
still widely used mainly due to its cost.

The impregnating oils should provide high dielectric strength, dielectric constant equal to that of paper, high
permeability to paper, and sufficient viscosity to enter the voids in paper. Their flash and solidifying points should
be >120 ºC and <–10 ºC, respectively. Mineral oil and synthetic oil (Askarels) are popular. Mineral oil-based
capacitors are quite expensive, while Askarel-based capacitors are harmful to the environment and humans. The
dielectric properties of the tissue paper and impregnating oils are given in Tables 1.3 and 1.4.

Aluminum foil of 6 μm thickness is widely used as the electrode material because of its high tensile strength,
low specific resistance, high melting point, low specific gravity, low cost, and easy availability.

EE509 High Voltage Engineering 1-15

Table 1.3 Properties of tissue paper.

Table 1.4 Properties of impregnating oils.

EE509 High Voltage Engineering 1-16

1.6 Supplementary Information on Insulating Materials

1.6.1 Sulphur Hexafluoride (SF 6 ) Gas

Generally, the preferred properties of a gaseous dielectric for high voltage applications are:
(a) High dielectric strength,
(b) Thermal stability and chemical inactivity towards materials of construction,
(c) Non-flammability and physiological inertness,
(d) Low temperature of condensation,
(e) Good heat transfer, and
(f) Ready availability at moderate cost.

Of the above properties, dielectric strength is the most important property of a gaseous dielectric for practical
use. The dielectric strength of gases is comparable with those of solid and liquid dielectrics (Fig. 1.2). This feature
of high dielectric strength of gases is attributed to the molecular complexity and the high rates of electron
attachment. Recently, the dielectric properties of many complex chlorinated and fluorinated molecular compounds
have also been studied (Fig. 1.3).

The physical and chemical properties of some commercially important insulating gases are shown in Table 1.5.
From the figures and the table, it is seen that SF6 has high dielectric strength and low liquefication temperature, and
it can be used over a wide range of operating conditions. SF6 also has excellent arc-quenching properties. Thus, it
is widely used as an insulating and arc-quenching medium in high voltage equipment such as high voltage cables,
current and voltage transformers, circuit breakers, and metal-enclosed substations. It is also seen that an addition of
30 % SF6 to air (by volume) increases the dielectric strength of air by 100%. One of the qualitative effects of
mixing SF6 with air is to reduce the overall cost of the gas while attaining relatively high dielectric strength or
simply preventing the onset of the corona at desired operating voltages. In addition to the use of SF 6 gas in recent
times, everyone knows of the essential quality of air as an insulating medium for overhead power transmission
lines and in air blast circuit-breakers.
EE509 High Voltage Engineering 1-17
 Fig. 1.2 DC breakdown strength of typical solid, liquid,
gas, and vacuum insulations in uniform fields.
Fig. 1.3 Breakdown strength of insulating gases for
75 cm diameter uniform field electrodes having
a 12 mm gap.

EE509 High Voltage Engineering 1-18

Table 1.5 Physical and chemical properties of some commercially important insulating gases.

EE509 High Voltage Engineering 1-19

1.6.2 Petroleum Oil (Transformer Oil)

The electrical properties that are essential in determining the dielectric performance of a liquid dielectric are:
relative permittity: the Er. Remembers?
(a) Capacitance per unit volume or relative permittivity,
(b) Resistivity,
(c) Loss tangent (tan δ) or power factor, which is an indication of the power loss under a.c. voltage
application, and
(d) Ability to withstand high electric stresses.

Permittivity of most petroleum oils varies between 2.0 and 2.6. The variation for Askarels and silicone oils is
from 4.5 to 5.0 and 2.0 to 73, respectively. In the case of non-polar liquids, the permittivity is independent of
frequency, but in the case of polar liquids such as water, it changes with frequency. For example, the permittivity
of water is 78 at 50 Hz and reduces to ~5.0 at 1 MHz.

Resistivity of insulating liquids used for high voltage applications should be more than 1016 ·m, and most of
the liquids in their pure state exhibit this property.

Power Factor of a liquid dielectric under a.c. voltage will determine its performance under load conditions.
Power factor is a measure of the power loss and is an essential parameter in cable and capacitor systems. However,
in the case of transformers, the dielectric loss in the oil is negligible compared to copper and iron losses. Pure and
dry transformer oils will have a very low power factor varying between 10 –4 at 20 ºC and 10–3 at 90 ºC at a power
frequency.

Dielectric Strength is the most critical parameter in the choice of a given liquid dielectric for a given
application. The dielectric strength depends on the atomic and molecular properties of the liquid itself. However,
under practical conditions, the dielectric strength depends on the material of the electrodes, temperature, type of
applied voltage, gas content in the liquid, etc., which changes the dielectric strength by changing the molecular

EE509 High Voltage Engineering 1-20

properties of the liquid. The above factors, which control the breakdown strength and lead to the electrical
breakdown of the liquid dielectric, are discussed in subsequent sections.

Table 1.6 shows the electrical properties of some liquid dielectrics used in transformers, cables, capacitors, and
other special applications. In practice, the choice of a liquid dielectric for a given application is made based on its
chemical stability. Other factors such as saving space, cost, previous usage, and susceptibility to environmental
influences are also considered. Transformer oil is the cheapest and the most commonly used liquid dielectric in
power equipment. It is an almost colorless liquid consisting of a mixture of hydrocarbons, including paraffins, iso-
paraffins, naphthalenes, and aromatics. When in service, the liquid in a transformer is subject to prolonged heating
at high temperatures of ~95 ºC, and consequently, it undergoes a gradual aging process. With time the oil becomes
darker due to the formation of acids and resins, or sludge in the liquid. Some of the acids are corrosive to the solid
insulating materials and metal parts in the transformer. Deposits of sludge on the transformer core, on the coils, and
inside the oil ducts can reduce oil circulation and thus its heat transfer capability. Complete specifications for the
testing of transformer oils are given in IS 1866 (1983), IEC 296 (1969), and IEC 474 (1974).

Table 1.6 Electrical properties of some commercial liquid dielectrics.

EE509 High Voltage Engineering 1-21

1.6.3 Solid Dielectrics

The majority of the insulating systems used in practice are solids. They can be broadly classified into three
groups: (1) Organic Materials, (2) Inorganic Materials, and (3) Synthetic Polymers. Some of these materials are
listed in Table 1.7.

Table 1.7 Classification of solid insulating materials.

Organic materials are produced from vegetable or animal matter with similar characteristics. They are good
insulators and can be easily adopted for practical applications. However, their mechanical and electrical properties
always deteriorate rapidly when temperatures exceed 100 ºC. Therefore, they are generally used after treatment
with a varnish or impregnation with an oil. Examples are paper and pressboard used in cables, capacitors, and
transformers.

EE509 High Voltage Engineering 1-22

 Inorganic materials, unlike organic materials, do not show any appreciable reduction (<10 %) in their electrical
and mechanical properties, almost up to 250 ºC. Typical inorganic materials used for electric applications are
glasses and ceramics. They are widely used to manufacture insulators, bushings, etc., because of their resistance to
atmospheric pollutants and excellent performance under varying temperature and pressure conditions.

Synthetic polymers are polymeric materials with excellent insulating properties and can be easily fabricated and
applied to the apparatus. These are generally divided into two types: thermoplastic and thermosetting plastics.
Although they have low melting temperatures of 100–120 ºC, they are very flexible and can be molded and
extruded at temperatures below their melting points. They are widely used in bushings, insulators, etc. Their
electrical use depends on their ability to prevent the absorption of moisture.

Some of the essential dielectric properties of the above materials are discussed below.

(a) Paper
The kind of paper commonly employed for insulation purposes is a special variety known as tissue paper or
Kraft paper. The thickness and density of paper vary depending on the application. Low-density paper (0.8 g/cm3)
is preferred in high-frequency capacitors and cables, while medium-density paper is used in power capacitors.
High-density paper is preferable for energy-storage capacitors and d.c. machines.

Paper is hygroscopic. Therefore, it has to be dried and impregnated with impregnants such as mineral oil,
chlorinated diphenyl, and vegetable oils. The relative dielectric constant of impregnated paper depends upon the
permittivity of cellulose of which the paper is made, the permittivity of the impregnant, and the density of the paper.
Table 1.8 gives the dielectric constants for different densities of paper impregnated with different oils.

When very thin (thickness 8–20 µm) paper is used, it is essential to see that the number of conducting particles
on the surface of the paper is minimum. The conventional method of detecting conducting particles uses a roller
and plate, the conduction being indicated by means of headphones.

EE509 High Voltage Engineering 1-23

Table 1.8 Dielectric constant and density of paper impregnated with different oils.

(b) Fibers
Fibers, when used for electrical purposes, will have the ability to combine strength and durability with extreme
fineness and flexibility. The fibers used are both natural and artificial. They include cotton, jute, flax, wool, silk
(natural fibers), rayon, nylon, terylene, Teflon, and fiberglass.

The properties of fibrous materials depend on temperature and humidity. Figures 1.4 and 1.5 show the variation
of 𝜀𝑟 and tan δ of various fibrous materials as a function of the frequency. It can be observed from these figures
that 𝜀𝑟 decreases with frequency, while tan δ is higher at lower frequencies. Most of the perfectly-dried fibers have
a dielectric constant between 3 and 8. The presence of ionic impurities (e.g., salt) considerably reduces the
electrical resistance of the fiber. Artificial fibers, such as terylene and fiberglass, absorb very little water and hence
have very high resistance. Table 1.9 gives the density, 𝜀𝑟 and tan δ of various fibers.

EE509 High Voltage Engineering 1-24

 Fig. 1.4 Variation of dielectric constant, 𝜺𝒓 with temperature for paper.
1. Trichlorodipheny impregnated paper.
2. Pentachlorodiphenyl-impregnated paper.

Fig. 1.5 Variation of tan δ with the density of the paper.

1. Trichlorodiphenyl-impregnated paper.
2. Mineral oil impregnated paper.
3. Dry paper.

EE509 High Voltage Engineering 1-25

Table 1.9 Electrical properties of fibrous dielectrics.

(c) Mica and Its Products

Mica is the generic name of a class of crystalline mineral silicates of alumina and potash. It can be classified
into four main groups: (1) Muscovite, (2) Phlogopite, (3) Fibiolite, and (4) Lipidolite. The last two groups are hard
and brittle and hence are unsuitable for electrical insulation. Mica can be split into a very thin flat laminate. It has
unique electrical properties such as high dielectric strength, low dielectric losses, resistance to high temperatures,
and good mechanical strength. These have enabled it to be used in many electrical apparatus. Very pure mica is
used for high-frequency applications. Spotted mica is used for low voltage insulation such as commutator segment
separators, armature windings, switchgear, and electrical heating and cooling equipment. Table 1.10 shows the
electrical properties of mica.

EE509 High Voltage Engineering 1-26

 Mica is built into sheet form by bounding together with a suitable resin or varnish. Depending on the type of
application, mica can be mixed with the required type of resin to meet the operating temperature requirements.
Micanite is another form of mica that is extensively used for insulation purposes. Mica splitting and mica powder
are used as fillers in insulating materials such as glass and phenolic resins. Using mica as a filler results in
improved dielectric strength, reduced dielectric loss, and improved heat resistance and hardness of the material.

Table 1.10 Electrical properties of muscovite and phlogopite mica.

EE509 High Voltage Engineering 1-27

(d) Glass
Glass is a thermoplastic inorganic material comprising complex systems of oxides (SiO 2). The dielectric
constant of glass varies from 3.7 to 10, and the density varies from 2.2 to 6 g/cm3. At room temperature, the
volume resistivity of glass varies from 10 12 to 1020 ohmcm. The dielectric loss of glass varies from 0.004 to 0.020,
depending on the frequency. The losses are highest at the lowest frequencies. The dielectric strength of glass varies
from 3,000 to 5,000 kV/cm. It decreases with increasing temperature, reaching half the value at 100 ºC. Glass is
used as a cover and for internal supports in electric bulbs, electronic valves, mercury arc switches, X-ray
equipment, capacitors, and insulators in telephones.

(e) Ceramics
Ceramics are inorganic materials that consolidate minerals into monolithic bodies by high-temperature heat
treatment. Ceramics can be divided into two groups depending on the dielectric constant. Low permittivity
ceramics (𝜀𝑟 < 12) are used as insulators, while the high permittivity ceramics (𝜀𝑟 > 12) are used in capacitors and
transducers.

Tables 1.11 and 1.12 give the various dielectric properties of some ceramics commonly used for electrical
insulation.

EE509 High Voltage Engineering 1-28

Table 1.11 Properties of low permittivity ceramics.

Table 1.12 Properties of high permittivity ceramics.

EE509 High Voltage Engineering 1-29

(f) Rubbers
Rubber is a natural or synthetic vulcanizable high polymer having high elastic properties. The electrical
properties of rubber depend on the degree of compounding and vulcanizing. General impurities, chemical changes
due to aging, moisture content, and variations in temperature and frequency have substantial effects on the
electrical properties of rubber. Some important electrical properties and applications of different types of rubber are
given in Table 1.13.

Table 1.13 Properties and applications of rubbers.

EE509 High Voltage Engineering 1-30

(g) Plastics
Plastics are widely used as insulating materials because of their excellent dielectric properties. Many new
developments in electrical engineering and electronics would not have been possible without the development of
plastics. Plastics are made by combining large numbers of small molecules into a few big ones. When small
molecules link to form the more giant molecules of the plastics, many different types of structures result. Most
thermoplastic resins approximate a structure in which several thousand atoms are tied together in one direction.
The thermosetting resins, on the other hand, form a three-dimensional network. Because of the large number of
plastics available, it will not be possible to deal with all of them, and only materials commonly used for insulation
are described.

(i) Polyethylene
Polyethylene is a thermoplastic material that combines unusual electrical properties, high resistance to moisture
and chemicals, easy processability, and low cost. It has high resistivity and good dielectric properties at high
frequencies. Therefore, it is widely used for power and coaxial cables, telephone cables, multi-conductor control
cables, TV lead-in wires, etc. By varying the methods of manufacture, different types of polyethylene are made
with specific properties for various applications. They may have low, medium, and high densities or may be
irradiated. The dielectric properties of these are summarized in Table 1.14.

Table 1.14 Electrical properties of polyethylene.

EE509 High Voltage Engineering 1-31

(ii) Fluorocarbon Plastics
Polytetrafluoroethylene (PTFE), polychlorotrifluoroethylene (PCTFE), and polyvinylidene (PVF2) plastics
come under this category. PTFE is the most thermally stable and chemically resistant of all three. It is considered
one of the best plastics used for insulation because of its excellent electrical and mechanical properties. It can be
used without decomposition up to temperatures of 327 ºC. It is widely used in almost all applications. P.C.T.F.E.
has a higher dielectric constant and loss factor than PTFE but melts at 190 ºC. PVF2 can be worked in the
temperature range of –30 to 150 ºC. It is used as thin wall insulation, jacketing for computer and special control
wires, and tubing and sleeving for capacitors, resistors, terminal junctions, and solder sleeves. The electrical
properties of fluorocarbons are tabulated in Table 1.15.

Table 1.15 Properties of fluorocarbon plastics.

EE509 High Voltage Engineering 1-32

(iii) Nylon
Nylon is a thermoplastic with high impact, tensile, and flexural strengths over a wide range of temperatures
(0 – 300 ºC). It also has high dielectric strength and good surface and volume resistivities even after lengthy
exposure to high humidity. It is also resistant to chemical action, and can be easily molded, extruded, and machined.
It is generally recommended for high-frequency, low-loss applications. In electrical engineering, nylon moldings
are used to make coil forms, fasteners, connectors, washers, cable clamps, switch housings, etc. There are three
different types of nylon commonly used. They are nylon 6/6, nylon 6, and nylon 6/10. The dielectric properties of
these three types are given in Table 1.16.

Table 1.16 Dielectric properties of nylon.

EE509 High Voltage Engineering 1-33

(iv) Polyvinyl Chloride
Polyvinyl chloride, or PVC, is used commercially in various forms. It is available as an unplasticized, tough,
and rigid sheet material and can be easily shaped to any required format. It is chemically resistant to strong acids
and alkalis and is insoluble in water, alcohol, and organic solvents like benzene. The upper-temperature limit of
operation is about 60 ºC. The dielectric strength, volume resistivity, and surface resistivity are relatively high. The
dielectric constant and loss tangent are 3.0–3.3 and 0.015–0.02, respectively, at all frequencies up to 1 MHz.
PVC is also available as a highly plasticized flexible material, which is used extensively for wire covering,
insulated sleeving, and cable sheathing in preference to natural rubber because of its resistance to the action of
sunlight, water, and oxygen.

(v) Polyesters
Polyesters have excellent dielectric properties and superior surface hardness and are highly resistant to most
chemicals. They represent a whole family of thermosetting plastics produced by condensing dicarboxylic acids and
dihydric alcohols and are classified as either a saturated or unsaturated type. Unsaturated polyesters are used in
glass laminates and glass fiber-reinforced moldings, both of which are widely used to make small electrical
components for large structures. Saturated polyesters are used in producing fibers and films. Polyester fiber is used
to make paper, mat, and cloth for electrical applications. The film is used for insulating wires and cables in motors,
capacitors, and transformers. The dielectric properties of polyester compounds are given in Table 1.17.

Mylor polyester film is used mainly in preference to paper insulation. Its dissipation factor is very low at power
frequencies, decreasing as increasing temperature. It has a dielectric strength of 2,000 kV/cm, and its volume
resistivity is better than 1015 ·cm at 100 ºC. Its high softening point enables it to be used at temperatures above
the operating limit of paper insulation. It has high weather resistance and can be buried under the soil. Therefore,
this can be used for motor and transformer insulation at power frequencies and high-frequency applications
subjected to varying weather conditions.

EE509 High Voltage Engineering 1-34

Table 1.17 Dielectric properties of polyesters.

(vi) Polystyrenes

Polystyrenes are obtained when styrene is polymerized with itself or with other polymers or monomers,
producing various thermoplastic materials with varying properties in different colors. Electrical grade polystyrenes
have a dielectric strength comparable to mica and have low dielectric losses, independent of the frequency. Their
volume resistivity is about 1019 ohm·cm, and the dielectric strength is 200 – 350 kV/cm. The dielectric constant at
20 ºC is 2.55, and the loss tangent is 0.0002 at all frequencies up to 10,000 MHz.

Polystyrene films are extensively used to manufacture low-loss capacitors, which will have a very stable
capacitance and high insulation resistance. Films and drawn threads of polystyrene are also used for high-
frequency and cable insulations.

EE509 High Voltage Engineering 1-35

(h) Epoxy Resins
Epoxy resins are thermosetting types of insulating materials. They possess excellent dielectric and mechanical
properties. They can be easily cast into desired shapes, even at room temperature. They are very versatile, and their
basic properties can be modified either by the selection of a curing agent or by the use of modifiers or fillers. They
are highly elastic; samples tested under very high pressures, up to about 18,000 psi (12,000 atm), returned to their
original shape after the load was removed, and the sample showed no permanent damage. Resistance to weathering
and chemicals is also very good. The tensile strength of Araldite CT200 and hardener HV901 is in the range of
5.5 – 8.5 kg/mm2, and the compressive strength is 11–13 kg/mm2. The dielectric constant varies between 2.5 and
3.8. The dielectric loss factor is very small under power frequency conditions lying in the range of 0.003 – 0.03.
The dielectric strength is ~750 kV/cm. The volume resistivity of the material is of the order of 10 13 ·cm.

Epoxy resins can be formed into an insulator of any desired shape for almost any type of high voltage
application, including insulators, bushings, apparatus, etc. It can also be used to encapsulate electronic components,
generator windings, transformers, etc. It is used to bond diverse materials such as porcelain, wood, metals, plastics,
etc. It is an essential adhesive used for the sealing of high vacuum joints. In any laboratory or industry where
electrical or electronic components or equipment are handled or manufactured, numerous occasions arise wherein
epoxy resins can be used to save time, labor, and money.

1.7 References

1. Naidu, M.S. and Kamaraju, V., High Voltage Engineering, 4th Edition, McGraw-Hill, New Delhi (2004).
2. Naidu, M.S. and Kamaraju, V., High Voltage Engineering, 2nd Edition, McGraw-Hill, New Delhi (1996).
3. Kuffel, E. E. and Zaengl, W.S. and Kuffel, J., High Voltage Engineering Fundamentals, 2nd Edition, Butterworth Heinemann,
Oxford (2000).
4. John, A.J. and Platts, J. R., High Voltage Engineering and Testing, Peter Peregrinus, Lodon (1994).
5. Shugg, W. T., Handbook of Electrical and Electronic Insulating Materials, 2nd Edition, IEEE Press, New York (1995).
6. Guide for the Determination of Thermal Endurance Properties of Electrical Insulating Materials, I.E.C. Publication, 216-1
(1974).

EE509 High Voltage Engineering 1-36