0% found this document useful (0 votes)
230 views16 pages

MS41908M

Uploaded by

dtx86vn
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
230 views16 pages

MS41908M

Uploaded by

dtx86vn
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 16

MS41908M

Lens Driver IC for Camcorder and Surveillance Camera(Built-in Iris Control)

PRODUCT DESCRIPTION
MS41908M is a lens driver chip for camcorder and

surveillance camera.

The chip incorporates iris control. It can enable extra-low

noise microstep drive by voltage driving way and torque ripple

correction technology.

FEATURES QFN44

⚫ Voltage Driving Way,

256 Microstep Drive Circuit (Two Channels)

⚫ Built-in Iris Control Circuit

⚫ Four-line Serial Bus Communication Control Motor

⚫ Built-in Open-drain Dual Systems for LED Drive

APPLICATIONS
⚫ Camcorder

⚫ Surveillance Camera

PRODUCT SPECIFICATION

Part Number Package Marking

MS41908M QFN44 MS41908M

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 1-
MS41908M
PIN CONFIGURATION

OP4OUT

OP4INN

CREFIN

VD_FZ
GNDA

VD_IS
VREF

RSTB

PLS2

PLS1

SIN
44

43

42

41

40

39

35

34
38

37

36
OP3INP 1 33 SCK

SENS 2 32 CS

OP3OUT 3 31 SOUT

REF 4 30 DVDD

AVDD3 5 29 OSCIN

ADTESTIN 6 MS41908M 28 GNDD

TEST 7 27 LED2

OUTE2 8 26 LED1

VDD5 9 25 OUTA1

GND5 10 24 MGNDA

OUTE1 11 23 N.C
12

13

14

15

16

17

21

22
18

19

20
MVCCA
OUTD2

OUTD1
N.C.

OUTB1
OUTC2

OUTC1
MVCCB

OUTA2
MGNDB

OUTB2

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 2-
MS41908M
PIN DESCRIPTION

Pin Name Type Description

1 OP3INP I Hall Signal Amplifier Positive Input

2 SENS O Hall Current Bias Output

3 OP3OUT O Hall Signal Amplifier Output

4 REF - Hall Current Bias Setting Impedance Connection Terminal

5 AVDD3 P 3V Analog Power Supply

6 ADTESTIN I ADC Test Input

7 TEST I Test Mode Input

8 OUTE2 O Motor Output E2

9 VDD5 P Iris Control Power Supply

10 GND5 - Iris Control GND

11 OUTE1 O Motor Output E1

12 N.C. - Not Connection

13 OUTD2 O Motor Output D2

14 MVCCB P Motor Power Supply B

15 OUTD1 O Motor Output D1

16 OUTC2 O Motor Output C2

17 MGNDB - Motor GND B

18 OUTC1 O Motor Output C1

19 OUTB2 O Motor Output B2

20 MVCCA P Motor Power Supply A

21 OUTB1 O Motor Output B1

22 OUTA2 O Motor Output A2

23 N.C. - Not Connection

24 MGNDA - Motor GND A

25 OUTA1 O Motor Output A1

26 LED1 O Open-drain 1 for LED Drive

27 LED2 O Open-drain 2 for LED Drive

28 GNDD - Digital GND

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 3-
MS41908M

Pin Name Type Description

29 OSCIN I OSCIN Input

30 DVDD P 3V Digital Power Supply

31 SOUT O Serial Data Output

32 CS I Chip Selection Signal Input

33 SCK I Serial Clock Input

34 SIN I Serial Data Input

35 VD_IS I Iris Control Image Synchronization Signal Input

Adjust Focal Length and Magnification for Image


36 VD_FZ I
Synchronization Signal Input

37 PLS1 O Pulse 1 Output

38 PLS2 O Pulse 2 Output

39 RSTB I Signal Input Initialization

40 GNDA - 3V Analog GND

41 CREFIN - (AVDD3)/2 Voltage Output Connection Capacitor Terminal

42 VREF O Hall Sensor Output with Reference Voltage

43 OP4INN I Amplifier Reverse Input Biased at the Intermediate Point

44 OP4OUT O Amplifier Output Biased at the Intermediate Point

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 4-
MS41908M
BLOCK DIAGRAM

AVDD3
GNDD

DVDD

GNDA
Driver A, B
MVCCA

CREFIN
OUTA1

OUTA2
VREF


OP4OUT

OP3INP
OUTB1
OUTB2
OP4INN

MGNDA
OP3OUT

SENS Driver C, D
MVCCB
8bit PWM
REF Current
Controller
DAC OUTC1
(Focus
Zoom OUTC2
DAC IRIS)


TEST ADC

OUTD1
ADTESTIN
OUTD2

MGNDB
CS
IRIS Driver
SOUT VDD5
SIF
&
SIN Control
Logic
SCK OUTE2
OSCIN OUTE1

GND5
Pulse LED
UVLO & TSD
Gen. Dr.
PLS1

LED1
VD_IS

PLS2

RSTB
LED2
VD_FZ

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 5-
MS41908M
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings
Note: Under no circumstances should the maximum ratings be exceeded in the application.
Parameter Symbol Rating Unit

AVDD3 -0.3  +4.0


Power Supply for Control Section1 V
DVDD -0.3  +4.0

Power Supply for Motor Control 1 1 MVCCx -0.3  +6.0 V

Power Supply for Motor Control 2 1 VDD5 -0.3  +6.0 V


Tolerance Loss Value2 PD 141.1 mW
Operating Temperature3 Topr -40  +100 °C
Storage Temperature3 Tstg -55  +125 °C

Motor Drive 1(Focus, Magnification)


IM1(CD) ± 0.25 A/ch
H-bridge Drive Current

Motor Drive(Iris)
IM2(CD) ± 0.15 A/ch
H-bridge Drive Current

Instantaneous H-bridge Drive Current IM(pluse) ± 0.4 A/ch

Digital Input Voltage4 Vin -0.3  (DVDD + 0.3) V

ESD HBM ± 3k V
Note: 1. The absolute maximum ratings can be applied within the tolerance range.
2. Tolerance loss value refers to the value of independent package at Ta = 85°C. When in practical use,
it is expected to carry out the heat dissipation design which does not exceed the tolerance loss value on the
base of technical data and PD - Ta characteristics diagram according to the power supply, load, operating
temperature.
3. Except for the tolerance loss value, operating temperature and storage temperature, all ratings are
for Ta = 25°C.
4. (DVDD + 0.3) voltage should not exceed 4.0V.

Operating Supply Voltage Range


Range
Parameter Symbol Unit
Min Typ Max

AVDD3 2.7 3.1 3.6

DVDD 2.7 3.1 3.6


Supply Voltage Range V
MVCCx 3.0 4.8 5.5

VDD5 3.0 4.8 5.5

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 6-
MS41908M
Terminal Allowable Current and Voltage Range
Note: 1. Terminal allowable current and voltage range, which is not allowed to exceed this electrical
parameter range under any circumstances.
2. Rated Voltage value referS to the voltage applied to GND terminals. GND refers to the voltage of
GNDA, GNDD, MGNDA and MGNDB. In addition, GND = GNDA = GNDD = GND5 = MGNDA = MGNDB.
3. 3V power supply refers to the voltage of AVDD and DVDD. In addition, AVDD3 = DVDD.
4. Voltage and current input from outside are strictly prohibited except for the terminals described
below.
5. For current, "+" indicates the current flowing to IC, "-" indicates the current flowing from IC.
Pin Port Name Range Unit
1 OP3INP -0.3  (AVDD3 + 0.3) V
6 ADTESTIN -0.3  (AVDD3 + 0.3) V
7 TEST -0.3  (DVDD + 0.3) V
29 OSCIN -0.3  (DVDD + 0.3) V
32 CS -0.3  (DVDD + 0.3) V
33 SCK -0.3  (DVDD + 0.3) V
34 SIN -0.3  (DVDD + 0.3) V
35 VD_IS -0.3  (DVDD + 0.3) V
36 VD_FZ -0.3  (DVDD + 0.3) V
39 RSTB -0.3  (DVDD + 0.3) V
43 OP4INN -0.3  (AVDD3 + 0.3) V
8 OUTE2 ± 0.15 A
11 OUTE1 ± 0.15 A
13 OUTD2 ± 0.25 A
15 OUTD1 ± 0.25 A
16 OUTC2 ± 0.25 A
18 OUTC1 ± 0.25 A
19 OUTB2 ± 0.25 A
21 OUTB1 ± 0.25 A
22 OUTA2 ± 0.25 A
25 OUTA1 ± 0.25 A
26 LED1 30 mA
27 LED2 30 mA
Note: (AVDD3 + 0.3) voltage should not exceed 4.0 V. And (DVDD + 0.3) voltage should not exceed 4.0 V.

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 7-
MS41908M
ELECTRICAL CHARACTERISTICS
VDD5 = MVCCx = 4.8 V, DVDD = AVDD3 = 3.1 V. Unless otherwise noted, Ta = 25°C±2°C.
Current Circuit, Common Circuit
Parameter Symbol Condition Min Typ Max Unit
MVCC Supply Current on Reset IOmdisable No Load, No 27MHz Input 0 3 μA
MVCC Supply Current on Enable Imenable Output Open Circuit 0.5 1.5 mA
3V Supply Current on Reset Icc3reset No 27MHz Input 0 10 μA
3V Supply Current on Enable Icc3enable Output Open Circuit 3.6 20 mA
VDD5 Supply Current on Reset Icc5reset No 27MHz Input 0 3 μA
VDD5 Supply Current on Enable Icc5enable Output Open Circuit 0.3 1 mA
RSTB = High, Output Open
Supply Current on Standby Iccstandby Circuit, 27MHz Input, Total 4 10 mA
Current
RSTB = High, Output Open
Supply Current When FZ = Enable, Circuit, 27MHz Input, FZ =
ICCps 5 12 mA
Iris = Power Save Enable, Total Current

Digital Input/Output
Parameter Symbol Condition Min Typ Max Unit
High-level Input Vin(H) RSTB 0.54×DVDD DVDD+0.3 V
Low-level Input Vin(L) RSTB -0.3 0.2×DVDD V
[SOUT] 1mA Current
SOUT High-level Output Vout(H): SDATA DVDD-0.5 V
Source
SOUT Low-level Output Vout(L): SDATA [SOUT] 1mA Current Sink 0.5 V
PLS12
Vout(H): MUX 0.9×DVDD V
High-level Output
PLS12
Vout(L): MUX 0.1×DVDD V
Low-level Output
Input Pull-down
Rpullret RSTB 50 100 200 kΩ
Impedance

Motor Drive Section 1 (Focal Length, Magnification)


Parameter Symbol Condition Min Typ Max Unit
Upper-side ON Resistance RonFZHS IM =200mA 0.8 Ω
Lower-side ON Resistance RonFZLS IM =200mA 0.7 Ω
H-bridge Leakage Current IleakFZ 0.8 μA

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 8-
MS41908M
Motor Drive Section (Iris)
Parameter Symbol Condition Min Typ Max Unit

Upper-side ON Resistance RonISHS IM = 200mA 1.75 Ω

Lower-side ON Resistance RonISLS IM = 200mA 1 Ω

H-bridge Leakage Current IleakFZ 0.8 μA

LED Drive
Parameter Symbol Condition Min Typ Max Unit

LED1 Output ON resistance RonLED1 IM = 20mA, 5V Cell 2 Ω

LED2 Output ON resistance RonLED2 IM = 20mA, 5V Cell 2.6 Ω

Output Leakage Current IleakLED 0.8 μA

OPAMP3 (HALL Sensor Output Amplifier)


Parameter Symbol Condition Min Typ Max Unit
Input Voltage Range VIN ½ AVDD3-0.5 ½ AVDD3 ½ AVDD3+0.5 V
Input Offset Voltage VOF -15 +15 mV
Output Voltage (Low) VOL ILOAD = - 100 μA 0.1 0.2 V
Output Voltage (High) VOH ILOAD = 100 μA AVDD3-0.2 AVDD3-0.15 V
Gain VOG Gain Set Value: 0h 20.5 21.8 22.8 V/V

OPAMP4 (Amplifier for Eliminating HALL Sensor Common-mode Voltage)


Parameter Symbol Condition Min Typ Max Unit
Input Voltage Range VIN ½ AVDD3-0.1 ½ AVDD3+0.1 V
Input Offset Voltage VOF -10 +10 mV
Output Voltage (Low) VOL ILOAD = - 10μA 0.1 0.2 V
Output Voltage (High) VOH ILOAD = 3 mA AVDD3-0.5 AVDD3-0.2 V

Reference Voltage Output Section


Parameter Symbol Condition Min Typ Max Unit

ILOAD = 0 A,
Output Voltage 1 VREF ½ AVDD3-0.1 ½ AVDD3 ½ AVDD3+0.1 V
CVREF = 100pF

ILOAD = ±100μA,
Output Voltage 2 VREFL ½ AVDD3-0.1 ½ AVDD3 ½ AVDD3+0.1 V
CVREF = 100 pF

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 9-
MS41908M
Hall Bias Control Section (SENS Terminal Output)
Parameter Symbol Condition Min Typ Max Unit

REF = 10kΩ, SENS = 0.7V


Minimum Output Current IBL 0 0 0.1 mA
Set Value: 00h

REF = 10kΩ, SENS = 0.7V


Output Current Accuracy 1 IB40H 0.9 0.99 1.1 mA
Set Value: 40h

REF = 10kΩ, SENS = 0.7V


Output Current Accuracy 2 IBBFH 2.8 2.95 3.1 mA
Set Value: BEh

Digital Input/Output
Parameter Symbol Condition Min Typ Max Unit

SCK,SIN,CS,OSCIN,
High Input Threshold Voltage Vin(H) 1.36 V
VD_IS,VD_FZ,TEST

SCK,SIN,CS,OSCIN,
Low Input Threshold Voltage Vin(L) 1.02 V
VD_IS,VD_FZ,TEST
RSTB Signal Pulse Trst 100 μs

SCK,SIN,CS,OSCIN,
Input Maximum Hysteresis Error Vhysin 0.34 V
VD_IS,VD_FZ,TEST
Image Synchronization
VDw 80 μs
Signal Width

Waiting Signal 1 of CS Signal T(VD-CS) 400 ns

Waiting Signal 2 of CS Signal T(CS-DT1) 5 μs

Pulse Generating Circuit


Parameter Symbol Condition Min Typ Max Unit
Wait Time for Pulse 1 to Arrive PL1wait OSCIN = 27MHz 20.1 μs
Pulse 1 Width PL1width OSCIN = 27MHz 1.2 μs
Wait Time for Pulse 2 to Arrive PL2wait OSCIN = 27MHz 20.1 μs

Iris Control
Parameter Symbol Condition Min Typ Max Unit

AD Referenced Frequency IRISSample OSCIN = 27MHz 500 kHz

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 10-
MS41908M
Overheat Protection
Parameter Symbol Condition Min Typ Max Unit
Overheat Protection
Ttsd 145 °C
Operating Temperature
Maximum Hysteresis Error of
ΔTtsd 35 °C
Overheat Protection

Power Supply Voltage Monitoring Circuit


Parameter Symbol Condition Min Typ Max Unit

3.3V Reset Vrston 2.48 V

3.3V Reset Maximum Hysteresis Error Vrsthys 0.2 V

MVCCx Reset VrstFZon 2.42 V

MVCCx Reset Maximum Hysteresis Error VrstFZhys 0.21 V

VDD5 Reset VrstlSon 2.42 V

VDD5 Reset Maximum Hysteresis Error VrstlShys 0.21 V

8-bit DAC for Hall Offset Adjustment


Parameter Symbol Condition Min Typ Max Unit
Adjustment Range (High) DAOTHof AVDD3 V
Adjustment Range (Low) DAOTLof 0 V

10-bit ADC
Parameter Symbol Condition Min Typ Max Unit

Input Range (High) Vin(H) AVDD3-0.2 V


Input Range (Low) Vin(L) 0.2 V
Differential Linearity Error DNL10A 1.0 LSB
Integral Linearity Error INL10A 2.0 LSB

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 11-
MS41908M
TYPICAL APPLICATION CIRCUIT DIAGRAM

0.1 μF

V+

Hall
Sensor
8.2kΩ H- H+

V- 0.01 μF
44 OP4OUT 100 pF 0.1 μF

43 OP4INN

41 CREFIN

VD_FZ

VD_IS
GNDA
VREF

RSTB

PLS1
PLS2

SIN
42

40

39

35
38

37

36

34
OP3INP 1 33 SCK

SENS 2 32 CS

OP3OUT 3 31 SOUT

AVDD3 REF 4 30 DVDD DVDD


(3. 1V) (3. 1 V)
AVDD3 5 29 OSCI N

ADTESTI N GNDD

TEST
6

7
MS41908M 28

LED2
27

OUTE2 8 26 LED1
VDD5
(4. 8 V) VDD5 9 25 OUTA1
M GND5 10 24 MGNDA

OUTE1 11 23 N.C.
21

22
12
OUTD2 13

MVCCB 14

15
OUTC2 16

MGNDB 17

OUTC1 18

OUTB2 19

20
OUTD1

OUTB1

OU TA2
MVCCA
N.C

MVCCB MVCCA
(4. 8 V) (4. 8 V)

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 12-
MS41908M
PACKAGE OUTLINE DIMENSIONS
QFN44(0606X0.75-0.4)

Dimensions in Millimeters Dimensions in Inches


Symbol
Min Max Min Max

A 0.700 0.800 0.028 0.031

A1 -0.004 0.046 0.000 0.002

A3 0.110REF 0.004REF

D 5.900 6.100 0.232 0.240

E 5.900 6.100 0.232 0.240

D1 - - - -

E1 - - - -

b 0.110 0.210 0.004 0.008

e 0.400TYP 0.016TYP

L 0.524 0.676 0.021 0.027

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 13-
MS41908M
MARKING and PACKAGING SPECIFICATIONS
1. Marking Drawing Description

MS41908M
XXXXXXX

Product Name: MS41908M


Product Code: XXXXXXX

2. Marking Drawing Demand


Laser printing, contents in the middle, font type Arial.

3. Packaging Specification

Device Package Piece/Reel Reel/Box Piece /Box Box/Carton Piece/Carton

MS41908M QFN44 4000 1 4000 8 32000

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 14-
MS41908M
STATEMENT

⚫ All Revision Rights of Datasheets Reserved for Ruimeng. Don’t release additional notice.

Customer should get latest version information and verify the integrity before placing order.

⚫ When using Ruimeng products to design and produce, purchaser has the responsibility to observe safety

standard and adopt corresponding precautions, in order to avoid personal injury and property loss

caused by potential failure risk.

⚫ The process of improving product is endless. And our company would sincerely provide more excellent

product for customer.

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 15-
MS41908M

MOS CIRCUIT OPERATION PRECAUTIONS

Static electricity can be generated in many places. The following precautions can be taken

to effectively prevent the damage of MOS circuit caused by electrostatic discharge:

1. The operator shall ground through the anti-static wristband.

2. The equipment shell must be grounded.

3. The tools used in the assembly process must be grounded.

4. Must use conductor packaging or anti-static materials packaging or transportation.

+86-571-89966911

Rm701, No.9 Building, No. 1 WeiYe Road, Puyan Street, Binjiang District, Hangzhou, Zhejiang

http:// www.relmon.com

Hangzhou Ruimeng Technology Co.,Ltd VERSION: V4.1 2024.05.21


http://www.relmon.com -PAGE 16-

You might also like